Point Mobile PM5 Quick Start Manual

V 2.0, Apr 2021 Copyright © 2021 Point Mobile Co., Ltd. All rights reserved. Point Mobile Co., Ltd. is the designer and manufacturer of mobile handheld devices. The Point Mobile logo is a registered trademark and symbol of Point Mobile Co., Ltd. Features and specifications are subject to change without prior notice. PM5 (Single trigger SKU)

1. Scanner 2. NFC tagging area 3. Battery release button 4. Battery 5. Trigger assembly latch 6. Trigger connector pin 7. Speaker 8. Reset button 9. LED Indicators 5 8 7 6 9 2 3 4 1 Standard Package PM5 Ring Scanner with battery pack Single Trigger

Install Battery 1. Align the connector on the PM5 with the connector on the battery 2. Slide and press the battery into the battery slot so that the battery is firmly engaged Remove Battery Single Trigger Parts 1. USB type C Connector 2. PM5 connector pin 3. Trigger locker 4. Trigger scan button 5. Cradle charging connector 6. Finger strap 4 2 6 3 1 5

PM5 with trigger can be worn on the index finger like a ring and is designed for ambidextrous use. Determine which hand do you wear PM5, and assemble trigger with right orientation. 1. Align the trigger so that the trigger scan button is positioned next to the thumb 2. Insert the opposite side of trigger locker to PM5’s trigger assembly latch first 3. Push the other end down until it clicks. Make usre that the trigger is engaged firmly 4. To remove the trigger, press the trigger locker and pull the trigger up. Left hand mount Right hand mount

1. Assemble the single trigger 2. Plug the USB type C cable to USB connector on the trigger and provide power through power supply 3. Confirm the connection with PM5’s LED indicator (Red – Charging / Green – Fully charged) Before using PM5 for the first time, charge the scanner at least 1 hour for stable operation. You can charge the PM5 and the battery with charging cradles, 4SC and 8SBC (Sold separately). Charging via Cradle (4SC, 8SBC) The cradles can connect up to 5 pcs, in one type only or two different types (4SC + 8SBC). You can charge more PM5 and batteries using it at the same time. 4SC Insert PM5 into cradle. Single trigger must be assembled to use 4SC. 8SBC Detach battery from PM5 and insert into cradle.

1. Insert the end of finger strap into the hole on the single trigger 2. Wear PM5 with trigger on the index finger as the scan button facing the thumb 3. Tighten the finger strap Power On & Warmboot Install battery and press and release scan button on single trigger. To reboot the PM5, press reset button for 3 seconds. Power On Warmboot

Connect PM5 with host device and control the configuration of the ring scanner using Ring Control or Ring Control Lite app. 1. Log in to Service Portal and go to the Download board. 2. Find a post about PM5 resources or Ring Control application. 3. Download and install Ring Control (Lite). • Ring Control - Only compatible with Point Mobile devices • Ring Control Lite – Compatible with other Android devices Barcode Reading To scan a barcode, aim the barcode while pressing the scan button on the single trigger. Aim the barcode so the center cross is centered on the barcode, and the whole barcode is inside the rectangle.

the host device. Above figure indicates how to Tap-to- Pair between PM85 and PM5. Tap-to-Pair is supported on SPP mode and HID mode, both. Tap-to-Pair Bluetooth Connection Scan the barcode provided by Ring Control (Lite) to make connection between host device and PM5. Scan-to-Pair is supported on SPP mode only. Scan-to-Pair There are two ways for connection between ring scanner and host device, Scan-to-Pair and Tap-to-Pair. Choose more comfortable method.

Category Description LED Sequence Beep Sequence Booting PM5 is powered on Green (Until the beep sequence ends) Short low → Short medium → Short high PM5 is booting as warmboot Blue None PM5 is booting after factory reset Red None Low battery warning Battery is low (Less than 20%) Red (Until the beep sequence ends) 4x Short high Battery Level (Press Reset button to activate) Battery level is more than 20% Green (For 5 seconds) None Battery level is between 10 % and 20% Blue (For 5 seconds) None Battery level is less than 10% Red (For 5 seconds) None Charging Charging battery Green None Fully charged Red None Bluetooth Communication Bluetooth connected Green Short medium → Short high Bluetooth disconnected Red 3x high

Check PM5’s status with beep sound and LED as below. Category Description LED Sequence Beep Sequence Firmware Update Updating firmware Blue blinking None Scanning Decoding success Green flash Short low Decoding success and Bluetooth is not connected Red 3x Short low Decoding fail Red flash Short medium → High Temperature warning Battery temperature is low (Under 0 ℃) Red High → Low → High → Low Battery temperature is critical low (Under -5 ℃ & Voltage is under 3.8V) None High → Middle → Middle → Low (Then shutdown)

We have included this bulletin to comply with Directive 2012/19/EU of the EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on Waste Electrical and Electronic Equipment (WEEE). This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed. In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound away. The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal. If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration. You can also contact your supplier for more information on the environmental performances of this product. CE Compliance (for EU only) This product is labeled with the CE mark in accordance with the provisions of the applicable RoHS Directive 2011/65/EU for this product and the electric accessories.