Pixel SXMLCR72-VR1 Installation Instructions

Installa�on Instruc�ons Pixel Technologies, Inc. | www.pixelsatradio.com | [email protected] | (800) 595-0845 | Page 1 Package Includes (1) SiriusXM™ Roady BT Display Controller (1) Intelligent Power Adapter (1) Handlebar Clamp Mount (1) RAM Ball Mount Adapter (25 MM) (1) Weatherproof Protec�ve Case (1) SiriusXM™ Antenna (1) Auxiliary Cable (1) L-Bracket with AMPS Plate & Lock Ring (1) AMPS Plate (Male Dual Notch) with Screws (1) Display Cable Loosen this screw Loosen this screw Rubber inserted here Step 1 - Install Clamp Mount Before ge�ng started, it is important to select an installa�on loca�on for the protec�ve case with receiver. A�er selec�ng the installa�on loca�on for the protec�ve case, loosen the two screws on the handlebar clamp mount all the way out and separate it from the back side of the clamp mount. Place the clamp mount on the handlebars, line up the screw holes and �ghten the screws to mount the clamp. Use the supplied rub- ber strips to increase the grip of the mount. BACK PLATE ASSEMBLY Locate the bag containing the parts shown below. AMPS Socket Plate with Lock Ring Dual Male AMPS Plate Metal L-bracket

Next, place the Dual Male AMPS Plate on the opposite side as the AMPS Socket Plate and line up the screw holes. Please note the posi�oning of the Dual Male AMPS Plate with the notches at the bo�om. The dual notches must be posi�oned at the bo�om in order to properly seat into the back of the case. Use the supplied screws and nuts to secure the plates to the L-bracket. The mount can be assembled with the top plate of the L-bracket facing forward or backwards to fit your installa�on needs. Next, slide the L-bracket assembly onto the back of the protec�ve case. The case should slide down over the dual notches. Op�onal - RAM Mount Assembly To install the kit onto a RAM mount, use the RAM Mount Adapter Plate located in the supplied parts bag. Screw the RAM Mount Adapter Plate to the L-bracket with the Dual Male AMPS Plate on one side and the RAM Mount Adapter Plate on the other side. The mount can be assembled with the top plate of the L-bracket facing forward or backwards to fit your installa�on needs. Next, slide the L-bracket assembly onto the back of the protec�ve case. The case should slide down over the dual notches. RAM Mount Adapter Pixel Technologies, Inc. | www.pixelsatradio.com | [email protected] | (800) 595-0845 Step 2 - Connect Mount to Back Plate and Mount Antenna To connect the handlebar or strap mount to the back plate, insert the ball joint into the AMPS Female Socket Plate with the Lock Ring having the wide end facing towards the socket plate. Push the mount into the socket un�l it clicks. Once the ball joint is firmly in place, screw the Lock Ring clockwise un�l it �ghtens all the way. To change the angle of the case, loosen the ring and pivot the case, then re�ghten the Lock Ring to secure. Do not over �ghten the Lock Ring to avoid damaging it. Next, place the antenna on the metal L-bracket and run the antenna wire through the bo�om of the case connec�ng it to the antenna port on the dock.

Roady BT Intelligent Power Adapter Unlike SiriusXM Dock and Play receivers, the tuner for the Roady BT is built into the Intelligent Power Adapter (cigare�e lighter power adapter). This means you will need to bring the display controller and power adapter with you when moving the unit from motorcycle to car or other loca�on. The power adapter also has all the connec�ons that would normally be on a docking cradle for older Sirius, XM and SiriusXM receivers. This means that you will need to route all cables to the power adapter except the display controller cable. This will be the only cable that will route to the protec�ve case. The next set of instruc�ons are provided as a basic reference for installing the Roady BT with the motorcycle kit parts. Re- fer to the Roady BT user guide for more detailed instruc�ons on how to install and operate the Roady BT. Connec�ng to the Intelligent Power Adapter Step 1 - Connect Antenna Cable In previous steps, we installed the magne�c antenna to the L-bracket. Run the antenna cable from the L-bracket to the loca�on of the power adapter and plug the antenna cable into the antenna port on the power adapter. Be sure to leave some slack in the line a�er rou�ng the cable from the case to the power adapter. Step 2 - Audio Connec�on The Roady BT has several different audio op�ons including Bluetooth®, Auxiliary, FM transmission and direct FM relay via the FMDA25. Each op�on requires a different setup. Refer to the Roady BT user guide for detailed installa�on instruc�ons on connec�ng audio. If you are connec�ng via Bluetooth® or FM transmission, you will start the process once the system is powered on. If you are connec�ng via AUX or an FMDA25, you will make your connec�ons to the power adapter before plugging in the adapter. Auxiliary Audio Out FM Audio Out Antenna Port

Step 3 - Connect Display Controller Included in the package is a micro USB to micro USB cable that powers the display controller. Run that cable from the power adapter to the protec�ve case. Feed the wire up through the bo�om of the case as shown in the figure to the right. The case has several different sized spacers. Use the spacer that best mounts the display controller inside the case. Note: Using all spacers will give you the best results when pressing bu�ons. The spacers will push the controller to the front of the case, making it easier to press the bu�ons on the controller. Addi�onal Resources Fully Assembled When fully assembled, the unit should look like the images below. Roady BT Quick Start Guide Roady BT Quick Start Guide