EGig eG2G24T Operation & User’s Manual

Auto-MDIX Modular Gigabit Ethernet Switch User's Manual I II 24 Ports + 2 Ports Gigabit Ethernet Switch Auto MDIX 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 RESET POWER 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 LINK / ACT 10 / 100M FDX LINK / ACT 10 / 100M FDX LINK/ACT Fiber Optic Gigabit Ethernet TX RX 1000BASE-T Gigabit Ethernet 1G 100M L.A. FDX AUTO MDIX

a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and radiates radio frequency energy and, if not installed and used in accordance with the user's manual, may cause interference in which case user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Chapter 1 -------------------------------------------------------------------1 Introduction ---------------------------------------------------------------------1 Key Features -------------------------------------------------------------------2 Chapter 2 -------------------------------------------------------------------3 Package Contents ------------------------------------------------------------3 Chapter 3 -------------------------------------------------------------------4 Front Panel Layout -----------------------------------------------------------4 24 RJ-45 10/100Mbps Switch Ports --------------------------------4 Uplink port----------------------------------------------------------------4 Reset----------------------------------------------------------------5 LED Definitions ----------------------------------------------------------6 Power LED --------------------------------------------------------------6 FDX LED -----------------------------------------------------------------6 10/100M LED -----------------------------------------------------------6 LINK/ACT LED ---------------------------------------------------------6 Gigabit Optional module series: -------------------------------------7 Gigabit 1000Base-T Gigabit Ethernet Module ------------------7 Gigabit 1000Base-SX Fiber Module(Multi-Mode) --------------8 Gigabit 1000Base-SX Fiber Module(Multi-Mode) --------------9 Gigabit 1000Base-LX Fiber Module(Single-Mode) ----------10 Gigabit 1000Base-LX Fiber Module(Single-Mode) ----------11 Rear Panel Layout ----------------------------------------------------------11 AC input-------------------------------------------------------------------11 Chapter 4 ------------------------------------------------------------------12 Rack Mounting ---------------------------------------------------------------12 Chapter 5 ------------------------------------------------------------------13 Installation ---------------------------------------------------------------------13 To connect the Switch to PCs, servers, and other network devices. -------------------------------------------------------13 To connect the Switch to a Switch or a Hub --------------------13 Chapter 6 ------------------------------------------------------------------14 Technical Specifications ---------------------------------------------------14 Appendix ------------------------------------------------------------------16 ANSI/TIA/EIA-568-A PLUG & Twisted-pair Cable -----------------16 EIA568A pin assignment: ------------------------------------------------16 Recommend CAT5 UTP specifications ------------------------------16 RJ-45 Modular Phone Jack: ---------------------------------------------17 I. II. III. IV. V. I. II. I. II. III. IV.

Modular switch Introduction The Switch provides 24 10/100Mbps ports. The Switch was designed for easy installation and high performance in an environment where traffic on the network and the number of user increase continuously. The 19-inch standard rack-mount size was specifically designed for ROBO (Remote Office & Branch Office) and medium to large workgroups. The Switch can be installed where space is limited; moreover it provides smooth network migration and easy upgrade to network capacity. -1- I II 24 Ports + 2 Ports Gigabit Ethernet Switch Auto MDIX 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 RESET POWER 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 LINK / ACT 10 / 100M FDX LINK / ACT 10 / 100M FDX LINK/ACT Fiber Optic Gigabit Ethernet TX RX 1000BASE-T Gigabit Ethernet 1G 100M L.A. FDX AUTO MDIX

IEEE802.3u 100BASE-TX IEEE802.3z 1000BASE-SX, 1000BASE-LX IEEE802.3ab 1000BASE-TStandards 24 ports 10/100Mbps Fast Ethernet switch and 2 ports Gigabit Ethernet optional slots, each allows for single-port Gigabit Ethernet Switch module 1000BASE-SX or 1000BASE-LX or 1000BASE-T Provided non-blocking and non-head-of-line-blocking full wire speed forwarding Built-in 16K MAC addresses 96Mbits dynamic packet buffer allocation for each port. - Total 8,000 Packet Capacity Store-and-forward switch mode Automatic learning of network configuration Broadcast storm control Flow control fully supported: Half-duplex mode a Collision-based Congestion Control Full duplex mode a 802.3x compliant Flow Control Status LEDs: Gigabits copper module: 100M, 1000M, Full Duplex, Link/Activity. Gigabits fiber module: Link/Activity. 10/100TX port: Link/Act, Speed, Full Duplex/Collision. System: Power All 100Base-TX or 1000Base-T (twisted pair) port support Auto MDIX crossover capabilities Provided front panel reset button -2-

contains the following items: One Fast Ethernet Switch Rack-mount Kit For Rack Installation One Power Cord One User's Manual Option Gigabit Module Note: If any of these items is found missing or damaged, please contact your local supplier for replacement. -3- 24 Port 10/100Mbps plus 2 Gigabit TX/FX Auto-MDIX Modular Gigabit Ethernet  Switch Hub User's Manual 24 Port Gigabit Switch Power Cord Rack-mount Kit User's Manual I II 24 Ports + 2 Ports Gigabit Ethernet Switch Auto MDIX 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 RESET POWER 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 LINK / ACT 10 / 100M FDX LINK / ACT 10 / 100M FDX I II 24 Ports + 2 Ports Gigabit Ethernet Switch Auto MDIX 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 RESET POWER 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 LINK / ACT 10 / 100M FDX LINK / ACT 10 / 100M FDX LINK/ACT Fiber Optic Gigabit Ethernet TX RX 1000BASE-T Gigabit Ethernet 1G 100M L.A. FDX AUTO MDIX 1000BASE-T Gigabit Ethernet AUTO MDIX Fiber Optic Gigabit Ethernet TX RX MT-RJ Gigabit Ethernet Option Gigabit Module

I. 24 RJ-45 10/100Mbps Switch Ports There are 24 RJ-45 connectors on the front panel for connecting to servers, workstation or other devices. The Switch provides 24 10/100Mbps switching ports that could sense the 10/100M speed and negotiate Full/Half-duplex mode automatically. The Switch provided new Auto-MDIX technology. Besides, it can auto detect the cable signal to make optimum connection. Please make sure the CAT. 5, 5e or CAT. 6 twisted pair cable meet the E/TIA568 standards. Please refer to the appendix at page 16 for quickly trouble-shooting. II. 2 Gigabit Optional module The Switch provided 2 Gigabit modular slots on the front panel for connecting to servers or other gigabit switches. The Gigabit modules have copper & fiber selection. The Gigabit modules only could negotiate Full-duplex mode and do not need jumper or software to configuration. The copper supports Auto-MDIX and Auto-negotiation function. The fiber supports multi-mode and single-mode at the SC or MT-RJ connector. Please refer to the gigabit modular list at page 7, 8, 9, 10 and 11 for detail. -4-

-5- 10 / 100M FDX 10 / 100M FDX LINK / ACT LINK / ACT POWER RESET 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 Yellow Yellow Yellow Green Green Green Green

Power LED On : The unit is powered on and ready for use. Off : The unit is powered off. FDX LED On : The port is operating at Full-duplex. Off : The port is operating at Half-duple without any data being transmitted or received. Flashing : Collisions occurred and the port is operating at Half-duplex mode. 10/100M LED (on the 24 10/100TX port) On : The port is on the 100Mbps status. Off : The port is on the 10Mbps status. LINK/ACT LED (on the 24 10/100TX port) On : The port is ready for 10/100Mbps connection. Flashing : The data is transmitted or received on the port. 100M LED (on the Gigabit module) On : The port link & work on the 100Mbps. LINK/ACT LED (on the Gigabit module) On : The port is ready for 100/1000Mbps connection. Flashing : The data is transmitted or received on the port. 1G LED (on the Gigabit module) On : The port link & work on the 1000Mbps. -6-

1000Base-T Gigabit Ethernet Module Model Name Description Compliant with IEEE802.3ab 1000Base-T Std. 1 x 1000Mbps STP port (RJ-45 connector). Support Auto-MDIX & Auto-negotiation. Supports Cat5, 5e or 6 twisted pair cable. Jumper-less configuration. Full duplex operation only. LED-indicators for 1000M, 100M, Link/ACT, FDX. -7- MB-001T 1000BASE-T Gigabit Ethernet AUTO MDIX

Model Name Description Compliant with IEEE802.3z 1000Base-SX Std. 1 x 1000Base-SX Fiber port (SC connector). Supports 62.5/125um or 50/125um multi-mode optic cable. Jumper-less configuration. Full duplex operation only. LED-indicators for Link/ACT. Distance: Use the 62.5/125um MMF optic cable for 220m (721 ft) links. Use the 50/125um MMF optic cable for 500 (1640 ft) links. -8- MG-001SC Fiber Optic Gigabit Ethernet TX RX

Model Name Description Compliant with IEEE802.3z 1000Base-SX Std. 1 x 1000Base-SX Fiber port (MT-RJ connector). Supports 62.5/125um or 50/125um multi-mode optic cable. Jumper-less configuration. Full duplex operation only. LED-indicators for Link/ACT. Distance: Use the 62.5/125um MMF optic cable for 220m (721 ft) links. Use the 50/125um MMF optic cable for 500 (1640 ft) links. -9- MG-001MT MT-RJ Gigabit Ethernet

Model Name Description Compliant with IEEE802.3z 1000Base-SX Std. 1 x 1000Base-LX Fiber port (SC connector). Supports 62.5/125um, 50/125um multi-mode and 9/125um single-mode optic cable. Jumper-less configuration. Full duplex operation only. LED-indicators for Link/ACT. Distance: Use the 62.5/125um MMF optic cable for 220m (721 ft) links. Use the 50/125um MMF optic cable for 500 (1640 ft) links. Use the 9/125um SMF optic cable for 10Km links. -10- MG-001LS Fiber Optic Gigabit Ethernet TX RX

Model Name Description Compliant with IEEE802.3z 1000Base-LX Std. 1 x 1000Base-LX Fiber port (MT-RJ connector). Supports 62.5/125um, 50/125um multi-mode and 9/125um single-mode optic cable. Jumper-less configuration. Full duplex operation only. LED-indicators for Link/ACT. Distance: Use the 62.5/125um MMF optic cable for 220m (721 ft) links. Use the 50/125um MMF optic cable for 500 (1640 ft) links. Use the 9/125um SMF optic cable for 10Km links. Rear Panel Layout AC input AC input (90~260V/AC, 50~60Hz) UL Safety. -11- MG-001LM MT-RJ Gigabit Ethernet OFF 50~60Hz ON 90~260VAC

standard EIA 19-inch rack. 24 port 10/100Mbps Switch is supplied with two mounting brackets, eight screws. First, put the Switch on the flat surface. Locate the mounting bracket on the sides of the Switch with the mounting holes on each. Next, insert the screw through the bracket and into the bracket mounting holes in the Switch. Then, place the Switch in to 19-inch rack. -12- II LINK/ACT Fiber Optic Gigabit Ethernet TX RX II LINK/ACT Fiber Optic Gigabit Ethernet TX RX

devices. Use straight-through twisted-pair cable (Cat. 5) to connect the Switch to PCs, servers and other network devices. Networks can be build as figure shown. II. To connect the Switch to a Switch or a Hub Use straight-through twisted pair cable to connect the Switch to another Switch or Hub on uplink port. If you connect the Switches on port 1 to port 24, the cable should be changed to crossover cable. -13- PC MAC Server Workstation 1 2 3 4 Dual Speed Hub Uplink Fast Ethernet Switch Gigabit Ethernet Switch PC PC PC PC PC MAC Server Server Workstation I II 24 Ports + 2 Ports Gigabit Ethernet Switch Auto MDIX 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 RESET POWER 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 LINK / ACT 10 / 100M FDX LINK / ACT 10 / 100M FDX LINK/ACT Fiber Optic Gigabit Ethernet TX RX 1000BASE-T Gigabit Ethernet 1G 100M L.A. FDX AUTO MDIX I II 24 Ports + 2 Ports Gigabit Ethernet Switch Auto MDIX 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 RESET POWER 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 LINK / ACT 10 / 100M FDX LINK / ACT 10 / 100M FDX LINK/ACT Fiber Optic Gigabit Ethernet TX RX 1000BASE-T Gigabit Ethernet 1G 100M L.A. FDX AUTO MDIX 8 Ports Smart Gigabit Ethernet Module Switch RESET POWER 1 1 2 3 4 5 6 2 3 4 5 6 FDX ACT 1000M 100M CONSOLE 19200 , 8 , N , 1 I II LINK/ACT Fiber Optic Gigabit Ethernet TX RX LINK/ACT Fiber Optic Gigabit Ethernet TX RX

- IEEE 802.3 10BASE-T; IEEE 802.3u 100BASE-TX - IEEE802.3z 1000BASE-SX, 1000BASE-LX - IEEE802.3ab 1000BASE-T 2. Protocol: - CSMA/CD 3. Number Of Ports - 24 integrated ports (10/100Mbps Nway port) - 2 optional Gigabit Ethernet module 4. Fully Flow Control Supported - Half-duplex mode: Backpressure - Full-duplex mode: IEEE 802.3x 5. Network Transmission Media - 10Base-T Cat. 3, 4, 5 UTP/STP - 100Base-TX Cat. 5 UTP/STP - 1000Base-T Cat5, 5e, 6 UTP/STP 6. Network Status Monitoring LEDs - System: POWER - 10/100TX port: LINK/ACT, 10/100M and FDX - Gigabit TP port: 100M, 1G, Link/ACT and FDX - Gigabit Fiber port: Link/ACT 7. Buffer Memory - RAM: 96Mbits per device 8. Filter/Forward Rate - Packet Filtering/ Forwarding Rates(By 64 packet length) -1000Mbps port - 148,800pps -100Mbps port - 148,800pps -10Mbps port - 14,880pps -14-

- Up to 16K per device 10. Power - AC input (90-240V/AC, 50-60Hz) UL Safety 11. Power Consumption - 23 Watts (Max) 12. Operating Temperature - 0 C ~ 60 C 13. Store Temperature - -20 C ~ 90 C 14. Humidity - 10% ~90% RH (Non-condensing) 15. Dimension (L x W x H) - 440mm x 220mm x 44mm 16. Weight - 3.2 Kg 17. Safety & EMI Certificates - CE & FCC-A -15- PC PC PC FTP Server Web Server Proxy Server Laptop Print Print Server WAN Router Firewall Gigabit Ethernet Switch Gigabit Ethernet Switch Fast Ethernet Switch I II 24 Ports + 2 Ports Gigabit Ethernet Switch Auto MDIX 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 RESET POWER 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 LINK / ACT 10 / 100M FDX LINK / ACT 10 / 100M FDX LINK/ACT Fiber Optic Gigabit Ethernet TX RX 1000BASE-T Gigabit Ethernet 1G 100M L.A. FDX AUTO MDIX 8 Ports Smart Gigabit Ethernet Module Switch RESET POWER 1 1 2 3 4 5 6 2 3 4 5 6 FDX ACT 1000M 100M CONSOLE 19200 , 8 , N , 1 I II LINK/ACT Fiber Optic Gigabit Ethernet TX RX 1000BASE-T Gigabit Ethernet 1G 100M L.A. FDX AUTO MDIX

The IEE802.3ab Standards permits the use of category 5 or better balanced cable pairs, installed according to ANSI/EIA-568-A. This appendix provides pinout and brief information for the CAT5 unshielded twisted pair cables II. EIA568A pin assignment: Pin Number Assignment Data Pair 3 + Data Pair 3 - Data Pair 2 + Data Pair 2 - Data Pair 1 + Data pair 1 - Data Pair 4 + Data Pair 4 - III. Recommend CAT5 UTP specifications Physical: FR-PVC cable construction Cable Type: 4-pair unshielded-twisted pair solid copper Conductors: 24 AWG, solid bare annealed copper Operating temperature: -20 0C to +75 0C Electrical: Impedance: 100 +15 % Near-End Cross-talk: 38dB @ 100 MHz Attenuation: 22 dB/100 m typical @ 100 MHz Maximum DC resistance: 9.38 /100 m (24 AWG) at 20 C Maximum DC insulation resistance: 150M /km -16- 1 2 3 6 4 5 7 8