TP-Link TL-SM331T Installation Manual

For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code. If you have any suggestions or needs on the product guides, welcome to email [email protected]. To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. RJ45 SFP Module Install the RJ45 SFP Module 1. Lock the yellow latch into place and insert the module into an SFP slot with label side up. 2. Gently push the module into the slot until you hear a click. Then, insert the RJ45 network cable. Remove the RJ45 SFP Module 1. Press the RJ45 crystal head and pull out the cable. Note: Images may differ from the actual products.

TP-Link devices. Note: *TL-SM331T does not support the data rate of 10 Mbps or 100 Mbps. **When a gigabit RJ45 SFP module is inserted into a 10G SFP+ slot, extra configuration for port data rate may be required. https://www.tp-link.com/support/download/tl-sm331t/#Compatibility To check the compatible TP-Link devices of your module, please scan the QR code or visit our website: Product Operating Temperature 0˚C to 70˚C (32˚F to 158˚F) Storage Temperature -40˚C to 85˚C (-40˚F to 185˚F) Storage Humidity 5% to 90% RH, Non-condensing Operating Humidity 10% to 90% RH, Non-condensing Environmental and Physical Specifications General Specifications RX_LOS MAC Interface Power Consumption (max.) Standards and Protocols Model Data Rate* (max.) TX_Fault TX_Disable Hot Swappable LLF LFP Cable Distance DDM 0.8 W / / Yes Yes / / 1000BASE-X 1.25 Gbps TL-SM331T 1000BASE-T: UTP cat.5e or above (max. 100m) / IEEE 802.3 IEEEE 802.3ab SFF-8472 Model Supported Gigabit SFP Slot (SFP Slot) TL-SM331T Supported** 10G SFP+ Slot (SFP+ Slot) 2. Pull down the latch and remove the module. Safety Information Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce. EU Declaration of Conformity UK Declaration of Conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Product Name: RJ45 SFP Module Model Number: TL-SM331T Responsible party: TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: [email protected] We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2021/09/14 This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. CE Mark Warning BSMI Notice 安全諮詢及注意事項 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 注意防潮，請勿將水或其他液體潑灑到本產品上。 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某 些適當的對策。 Explanation of the symbols on the product label RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. Note: The product label can be found at the bottom of the product. 限用物質含有情況標示聲明書 產品元件名稱 PCB 外殼 產品元件名稱 PCB 外殼 限用物質及其化學符號 備考： "○"系指該項限用物質之百分比含量未超出百分比含量基準值。 鉛 Pb ○ ○ 鎘 Cd ○ ○ 汞 Hg ○ ○ 六價鉻 Cr+6 ○ ○ 多溴聯苯 PBB ○ ○ 多溴二苯醚 PBDE ○ ○ CAN ICES-3 (A)/NMB-3(A) Industry Canada Statement Indoor use only Caution Operator’s manual