total sheds Pent Potting Shed Assembly Manual

STEP • 15 09 © Sheds (Midlands) Limited 2021 www.totalsheds.co.uk = Drill Points using screws provided as shown SIDE & CORNER STRIPS SIDE & CORNER STRIPS Hide the panel edges. Cover the framework & seams. 14a. Use all the side/corner strips to finish off the shed, by covering any exposed framework and the panel joining seams. INFORMATION The Corner Strips cover all panel edges. Remember to attach these to the exterior back panels too. 14b TACKS PROVIDED ATTACH THE ROOF FELT Use the felt lengths provided. 15a. Apply the roof felt as shown. Apply lower levels first to create corre ...

STEP • 19 09 © Sheds (Midlands) Limited 2021 www.totalsheds.co.uk SECURE THE SHELVING SECTIONS IN PLACE (If 6ft, 10ft, 14ft or 18ft Start with the 2ft Shelf Section). 18a. Insert the shelf assembly into the correct section of the shed interior. 18b. Use 4.0 x 70mm screws to secure the shelving panels in place. Use 4 screws per shelf panel to ensure that the section is properly secured. 18c. Repeat this for all shelving sections. For the 6ft, 10ft, 14ft and 18ft Builds, the 2ft section will always be first. SECURING THE SHELVES = Drill Points using screws provided as shown x2 4.0 ...

02 Unpack all of the components and check that you have all the parts required. Please use the checklist on previous page. Carefully dispose of the delivery pallet and any excess timber. Advisable: The underside of the floor must be treated with a quality wood preserver. Recommended: Paint shed in an oil based treatment to prevent water ingress into the timber. Also silicon your windows (Must silicon inside & outside) to prevent rain water seeping through the gaps between glass and the timber. SHED FLOOR: Setting Shed Base Unpacking your Parts SET THE SHED FOUNDATION Th ...

STEP • 7 05 = Drill Points using screws provided as shown = Drill Points using screws provided as shown x2 4.0 x 70mm Per Floor Section x3 x2 4.0 x 70mm Per Floor Section x3 x3 x3 4.0 x 70mm 4.0 x 70mm Per Panel Edge Per Panel Edge © Sheds (Midlands) Limited 2021 www.totalsheds.co.uk 4FT WINDOW PANEL 2FT WINDOW PANEL 4FT WINDOW PANEL 4ft FRONT WINDOW PANEL Fix the First 4ft Window Panel 7b. 2ft WINDOW PANEL 2ft WINDOW PANEL Place the Window panel againts far right of shed floor as shown. IMPORTANT Start Build point from Left to Right of Shed NOTE: Place panel to sit firmly on the ...

Per Floor Section x3 STEP • 16 STEP • 17 10 = Drill Points using screws provided as shown © Sheds (Midlands) Limited 2021 www.totalsheds.co.uk FELT STRIPS ATTACH FELT STRIPS Create the Final Roof Edges. Final steps finishing off the roof. 16a. Using the felt strips provided cover the edges of the roofs and ends of the roof felt. You will need to measure these and saw to fit to your requirements and create the perfect roof finish as shown below. 16b. Drill in the felt strips as shown on front and back of the shed to finish the roof off. Use the framework of the roof blocks to ...

STEP •11 07 © Sheds (Midlands) Limited 2021 www.totalsheds.co.uk = Drill Points using screws provided as shown x2 4.0 x 70mm Per Floor Section x3 x3 4.0 x 70mm Per Window Panel 4ft DOOR PANEL DOOR PANEL Attach Door Panel Next to the 2ft Window Panel 10a. Use the RED areas below as reference to the joining points of the final panel. Note the 4ft section should fit perfectly to continue the front section. x2 4.0 x 70mm Per Floor Section = Drill Points using screws provided as shown x3 x4 4.0 x 70mm 6ft SIDE PENT ANGLE TOPS SIDE PENT ANGLE TOPS Now attach all the 6ft Side Tops of P ...

02 Unpack all of the components and check that you have all the parts required. Please use the checklist on previous page. Carefully dispose of the delivery pallet and any excess timber. Advisable: The underside of the floor must be treated with a quality wood preserver. Recommended: Paint shed in an oil based treatment to prevent water ingress into the timber. Also silicon your windows (Must silicon inside & outside) to prevent rain water seeping through the gaps between glass and the timber. SHED FLOOR: Setting Shed Base Unpacking your Parts SET THE SHED FOUNDATION Th ...

STEP • 15 09 © Sheds (Midlands) Limited 2021 www.totalsheds.co.uk = Drill Points using screws provided as shown SIDE & CORNER STRIPS SIDE & CORNER STRIPS Hide the panel edges. Cover the framework & seams. 14a. Use all the side/corner strips to finish off the shed, by covering any exposed framework and the panel joining seams. INFORMATION The Corner Strips cover all panel edges. Remember to attach these to the exterior back panels too. 14b TACKS PROVIDED ATTACH THE ROOF FELT Use the felt lengths provided. 15a. Apply the roof felt as shown. Apply lower levels first to create corre ...