Toshiba NV Series Instruction Manual

6F8C1583 34 5.2.1 Controller interface (I/O variables) structure 5.2.1.1 Normal mode Use the I/O variable to access to the status/command. The status/command is used to do handshake to send/receive data between CF622 and the type1 light controller. Offset IWn CH1 Status IWn+1 CH2 Status QWn+2 CH1 Command QWn+3 CH2 Command Figure 5-14 I/O variables structure Details of Status and Command are shown as follows. (1) Status The status is used to do handshake to send/receive data and error information between CF622 and the user’s application. CF622 writ ...

6F8C1583 16 16 3.2.2 4-bit DIP switch (reserve) 4-bit DIP switch is reserve switches for future works. Figure 3-1 Operation mode setting switch REMARK ・ Do not use reserve switches. Table 3-2 4-bit DIP switch settings Switch no. Function OFF ON M1 Reserve Normal - M2 Reserve Normal - M3 Reserve Normal - M4 Reserve Normal - 1 2 3 4 M1 M2 M3 M4 ON→ ...

Unified Controller nv series type1 light Communication Interface Module (CF622) Instruction Manual 45 （7）Timeout check time (offset +13) Parameter 13W contain the receive timeout interval between characters of the receive data. Receive timeout is not checked if it is set to 0. Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name Receive timeout(0 - 600) × 100 [ms] Default 600 R / W R / W ...

This chapter describes how to install and wire CF622. Before installation and wiring, read this operation manual thoroughly. 4.1 Installation Condition and Mounting Base Unit ··········· 18 4.2 Mounting/Dismounting Modules ······························· 19 4.3 Power Supply Wiring and Grounding ························ 20 4.3.1 Power supply wiring ·············································· 20 4.3.2 Grounding ·················� ...

6F8C1583 58 7 7.1 CF622 cannot start up When the power is turned on, if the RUN LED located on the front panel of CF622 is not turned on, check the following: Power on On the PS module, is “POWER” LED is on? YES NO Is CF622 mounted to a base unit correctly? On CF622, “ERR” LED is off? On CF622, RESET switch is off? If CF622 is abnormal, Contact our service representatives. YES YES YES YES Go to “Power system check” written in “Unified Controller nv series type1 light Controller Unit User’s Manual - Basic Hardware - (6F8C1497) 7.1. If “RUN” LED is ...

Unified Controller nv series type1 light Communication Interface Module (CF622) Instruction Manual 27 5.1.1 Registration of CF622 Register CF622 to engineering tool with the following procedure. 1 Registration of type1 light station Select the [Station] sub folder and select from the menu. Figure 5-1 Registration of the station When the registration dialog appears, input a model and name as follows. Input Station Name (ex “CF622-Station”). Select Station Catcode [nv light station], Click OK . Figure 5-2 Registration of the station ...

6F8C1583 80 E ■ Describe 16#000D MOVE_WORD 6000 Param.Timeout MOVE_UINT 16#0001 Param.Mode MOVE_WORD 256 MOVE_UINT 0 Param.Wire MOVE_WORD 0 MOVE_WORD Param.Delimiter Param.Rcv MsgLen Param.RSCSCtrl 256 MOVE_UINT 0 MOVE_UINT 16#0054 Param.Format MOVE_UINT Param.SndMsgLen Param.AddMsgLen 16#8000 MOVE_WORD MWRITE E T TADDR P N Target 1 ( ) Trash |↑| EQ_WORD 16#0400 Target 1 ( ) Trash MREAD E T TADDR P N (S) Enable Param.Status Param.Command Param.Status Param.Command | | Req | | Req 8961 8960 ...