SEON vMax Pulse Install And Setup Manual

Install and Setup Guide © Seon Design Inc. | November 2016 | All rights reserved. www.seon.com Part Number: 700-1065 R001 Installation Kit Contents • Pulse Receiver (032-1022) • Antenna (085-1041) • Power Supply (085-1060) • Mounting Bracket (660-1052) • Mounting Screws • Installation Guide Tools Required • Phillips driver bit • 5/32” diameter drill bit • Power drill • Marking pen 1. Receiver Installation 1. Select an interior location with a line of sight to the vehicles entering or leaving the yard. The unit should be installed at least 8” inches away from users. 2. Using the screw holes on the back plate, mark the screw positions. 3. With the label arrow facing downward, fasten the receiver to the wall using the 4 supplied screws. 4. Attach the antenna to the antenna connector. 5. Attach the AC cable to the power connector. 6. Plug the AC cable to AC power. 2. LEDS LEDs on the receiver indicate power, signal, and data transfer activity. . *700-1065* WARNING: RF Exposure A separation distance of 7.875” (20 cm) or more should be maintained between the antenna of this device and persons during device operation. POWER Lit - DC power is present TR Terminal Ready, lit - data is being transmitted CD Carrier Detect, lit - data connection established LS Link Status, lit - power and connection, but no data in or out. slow blink - searching for a connection fast blink - transmitting or receiving - or SIM card not installed. Signal Single bar - Very weak signal Double bar - Weak signal Triple bar - Good signal Install this unit with the arrow pointing down Antenna Connector Power Connector

password provided by Seon. 4. Assign Senders to Vehicles Installers provide a list of ID numbers for all Senders, and the vehicles they are installed in. Perform the following steps to assign all the devices to vehicles in the vMax Pulse Web site: 1. On the dashboard, select the fleet from the drop down menu. 2. Above the dashboard, click Devices. 3. In the Devices list, locate the {unassigned} Sender ID in the Pulse Box serial number list. 4. In the Actions column for the Sender, click Assign. 5. In the Sender Assignment dialog, enter the vehicle number and select the fleet. Click Save,. 6. Above the Devices list, click Dashboard. 7. In the dashboard view, confirm that the vehicle is displayed. 8. Click the vehicle icon to see the vehicle history. 9. Repeat for all fleet vehicles. 10. When the installation is complete, click Log Out. 5. Specifications Service If your vMax Pulse system is to be returned to Seon Design for service, please call toll free 1-877-630-7366, or 604-941-0880, and provide the model and/or serial number of your unit. Ask for a Return Authorization (RA) number. An RA number allows the Service Technicians to better track your product when it comes in for service. Please show the RA number on the outside of the package. ANY PRODUCT SENT TO SEON DESIGN WITHOUT AN RA NUMBER MAY BE REFUSED. Warranty For full warranty information, go to www.seon.com/warranty.html. Information in this guide is subject to change without notice. Customer Service Contact Information Power Consumption 15 W max. @ 12 VDC Operating Voltage 12 VDC Operating Temperature Range 32 to 140°F (0 to 60°C) Compliance FCC Part 15 Class B EMC - EN55022 Class B, EN55024 Safety - UL/IEC 60950-1 - ANSI/ISA - 12.12.01 2013, CSA C22.2 No. 213 - EN 60079-0:2012+A11:2013 - EN 60079-15:2010 Network - GCF, PTCRB (approved modules) Enclosure weight 12 oz. (340 grams) Enclosure Size, LxWxH 4 1/2” (114 mm) x 1.13/16” (46 mm) x 15/16" (49 mm) Enclosure Material Plastic Toll free telephone 1-877-630-7366 Local telephone 604-941-0880 Email: [email protected] Web: www.seon.com