Toshiba NV Series Instruction Manual

6F8C1509 68 68 D.1 Decimal-hexadecimal Conversion Table Table D-1 Decimal-hexadecimal conversion table (1) Decimal Hexadecimal Decimal Hexadecimal Decimal Hexadecimal Decimal Hexadecimal 0 0 32 20 64 40 96 60 1 1 33 21 65 41 97 61 2 2 34 22 66 42 98 62 3 3 35 23 67 43 99 63 4 4 36 24 68 44 100 64 5 5 37 25 69 45 101 65 6 6 38 26 70 46 102 66 7 7 39 27 71 47 103 67 8 8 40 28 72 48 104 68 9 9 41 29 73 49 105 69 10 A 42 2A 74 4A 106 6A 11 B 43 2B 75 4B 107 6B 12 C 44 2C 76 4C 108 6C 13 D 45 2D 77 4D 109 6D 14 E 46 2E 78 4E 110 6E 15 F 47 2F 79 4F ...

does not guarantee the intellectual property rights or other rights of Toshiba or third parties nor allows license of its use. 2. No part or the whole of this document may be reproduced without prior consent. 3. The information herein may be changed in the future without notice. 4. All possible measures have been taken to prepare the information herein. If you have any question, comment, or find any error, please contact us. PROSEC, TOSLINE, TOSDIC are registered trademarks of To ...

Installation and Wiring This chapter describes installation and wiring methods of the IS911 module. Before installation and wiring, read this operation manual thoroughly. 2.1 Types of I/O Base Units ··············································· 14 2.2 Installing the Module ··················································· 15 2.3 Replacing the Module ·················································· 19 2.3. ...

6F8C1509 30 Module registration and parameter registration are performed in the following order. (1) System registration  Register the system name, and register the nv type2 module configuration and the TC-net I/O configuration that connects IS911.  Register IS911 on the network. (2) PLC registration  Register the PLC that transmits with IS911 in “other station”.  Register the PLC to the network. (3) IS911 module parameter settings  Set the transmission format using the module parameters.  Set the transmission partner PLC, transmission data type, data n ...

6F8C1509 16 CAUTION When using it in an environment with extreme vibrations, insert a cushion rubber cap (ADP901) or other cushion material between the base unit and DIN rail stopper. This will prevent damage and scratch of the case. Mandatory 2 Connect the base unit connection cable and terminating connector. Terminating connector is a terminating-only connector that has a terminating resistor inside. Connect the terminating connector to the base unit at the both ends of the TC-net I/O bus. Normally, the base unit BU901 of the SA911 is located at the end of ...

6F8C1509 64 B.1 Outline drawing The following figure shows the outside dimensions of the IS911. Figure B-1 IS911 outside dimensions 35 95 185 IS911 TX RX MOD RUN ERR I/O STN-H STN-L I/O TOOL MODE RS-232C MAINT ↓RUN RS-485 2W/4W D1/TXD1 D0/TXD0 - /RXD1 - /RXD0 GND 1 2 3 4 5 Front Side Top ...

Unified Controller nv series TC-net I/O Serial Communication Module IS911 Instruction Manual 61 A.2 IS911 Module Specifications Table A-2 IS911 Module specifications Item Specification Transmission Specifications Applicable standard RS485 (4W Only), RS232C Data transmission speed 1200bps, 2400bps, 4800bps, 9600bps, 19200bps Communication method Half-duplex communication method Synchronization method Asynchronous type Topology  RS-232C 1:1  RS-485 / RS-422 1:N (Max 32) Cable length  RS-232C Max15m  RS-485 Total extension 500m Protocol ...

6F8C1509 46 46 4.1 Operation This chapter describes the operations of the IS911 module, such as checking before operation, startup, and shutdown. The switches of the product have been adjusted for the system at the site adjustment. For normal operation, do not change any switch other than the ones the customer is required to operate. CAUTION Avoid incorrect setting. The product does not operate normally if the switches are set incorrectly. Read this operation manual thoroughly to avoid incorrect setting. Prohibited CAUTION Stop using immediately when an error occurs. Whe ...