Venturer PLV36220S1 Instruction Manual

SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: • DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. • TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF WALL OUTLET, THEN FULLY INSERT. • USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. WARNING : • TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT. • SHOULD ANY TROUBLE OCCUR, DISCONNECT THE AC POWER CORD AND REFER SERVICING TO A QUALIFIED TECHNICIAN. PLACEMENT INFORMATION • Do not use this unit in places that are extremely hot, cold, dusty or humid. • Do not restrict the airflow of this unit by placing it somewhere with poor air flow, by covering it with a cloth, by placing it on bedding or carpeting. • The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. SAFETY INFORMATION • When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard. • When you are not going to use the unit for a long period of time, disconnect the AC power cord. CONDENSATION INFORMATION • When left in a heated room where it is warm and damp, water droplets or condensation may form inside the equipment. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1-2 hours before turning the power on or gradually heat the room and let the unit dry before use. RATING PLATE LOCATION The rating plate is located on the rear of the unit. FCC STATEMENTS NOTE: This unit has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is not guarantee that interference will not occur in a particular installation. If this unit does cause harmful interference to radio or television reception, which can be determined by turning the unit off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the unit and receiver. - Connect the unit into a wall outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the unit. The symbol for Class II (Double Insulation)

IMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS SAFETY PRECAUTIONS ................................ 1 IMPORTANT SAFETY INSTRUCTIONS ............................................................................. 2 TABLE OF CONTENTS ................................... 2 QUICK INSTALLATION ...............................3-4 ACCESSORIES ................................................ 5 GETTING STARTED ......................................... 5 REMOTE CONTROL REFERENCE GUIDE ............................................................................. 6 CONTROL REFERENCE GUIDE ..................... 7 CONNECTIONS ........................................... 8-11 Connecting a TV Antenna / Cable / Satellite ...................................................................... 8 Connecting an A / V Device ........................ 8 Connecting Devices with a Composite (Yellow RCA-Type) Video Output ............................ 9 Connecting Devices with a Composite (Yellow RCA-Type) Video Input ............................... 9 Connecting a High-Definition (HD) Source ..................................................................... 10 Connecting a PC ......................................... 10 Connecting an Audio Amplifier .................... 11 Connecting the AC Power Cord ................. 11 USING HEADPHONES ................................... 11 TV SETUP ................................................ 12-16 Picture Menu ............................................... 12 Audio Menu ............................................... 12 TIME Menu ................................................... 13 Set Up Menu ........................................ 13-14 Parental Menu ..................................... 14-15 TV Menu ...................................................... 16 MAINTENANCE ............................................... 17 TROUBLESHOOTING GUIDE ....................... 17 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (Including amplifiers) that produce heat. 9) Do not defect the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your wall outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments / accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

QUICK INSTALLATION ATTACHING THE BASE STAND • Before attaching (or detaching) the stand, unplug the AC cord from the AC input terminal. Note: To detach the base stand, perform the steps in reverse order. CAUTIONS: • Attach the base stand in the correct direction. • Incorrect installation of the stand may result in the unit falling over. • Be sure to follow the instructions. 1. Confirm 4 screws (silver screws x2 & black screws x2) are supplied with the unit. 2. Lay the unit down on a flat surface, so the backside is facing up, making sure to place a soft cushioned material (such as a pillow or thick piece of foam) beneath the screen. 3. Attach the BASE STAND to the opening on the rear of the unit. 4. Insert and tighten the four screws (supplied) into the holes as shown below. WARNING: The LCD display is very fragile and must be protected at all times when attaching the base stand. Be sure that nothing hard or sharp, or anything that could scratch or damage the LCD display, comes in contact with it. Do NOT place pressure on the front of the unit at any time because the screen could crack. MOUNTING ON THE WALL This unit is VESA-compliant, and is designed to be wall-mounted with a VESA-compliant 3 15/16” x 3 15/ 16” (100mm x 100mm) mounting kit designed for flat-panel TVs (sold separately). Mount this unit according to the directions included with the mounting kit. Four mounting holes 3 15/16” 3 15/16” The Base Stand Soft cushion Silver screws (x2) Black screw (x1) Black screw (x1)

QUICK INSTALLATION When you turn on your television set for the first time, be sure to place it on a solid stable surface. To avoid danger, do not expose the TV to water, or a heat source (e.g. lamp, candle, radiator). Do not obstruct the ventilation grid at the rear and be sure to leave sufficient gaps around the unit as shown. TURNING ON THE UNIT FOR THE FIRST TIME The first time you turn on the unit, the unit will enter Setup mode. You can easily follow the prompt message on the screen to complete basic TV settings. 1. Press the / button to select Yes. Press the ENTER button to proceed with the initial setup. 2. Use the / button to select Antenna, then press the / button to select Air or CATV. 3. Use the / button to select Auto Scan, then press the button to enter auto scan menu. Use the / button to select Start to Scan, and press the button to begin scanning (If you selected CATV on Step 2, you need to select Cable System before Start to Scan). The system will automatically start to scan and preset all available TV channels. 4. After scanning has finished, the system will return to the first TV channel scanned. Make sure the RF aerial has been connected properly to the TV ANTENNA input jack on the rear of the system. :SELECT Proceed with auto scan ? No Yes "ENTER":COMFIRM PICTURE AUDIO TIME SET UP PARENTAL TV TV Antenna Auto Scan Auto Scan Add CH Channel Skip Channel No. Channel Label DTV Signal CATV UP/DOWN ADJUST "MENU":EXIT PICTURE AUDIO TIME SET UP PARENTAL TV TV Cable System Start to Scan AUTO UP/DOWN ADJUST "MENU":EXIT PICTURE AUDIO TIME SET UP PARENTAL TV TV RF CH Found 16 0 : : PRESS TO EXIT AUTO SCAN

ACCESSORIES Please check and identify the supplied accessories. Remote Control ......................................................................................................................... x 1 “AAA” Batteries (for remote control) ........................................................................................ x 2 Screws (for base stand) .......................................................................................................... x 4 GETTING STARTED USING THE REMOTE CONTROL • Point the remote control at the remote sensor located on the unit. • When there is a strong ambient light source, the performance of the infrared remote sensor may be degraded, causing unreliable operation. • The recommended effective distance for remote operation is about 16 feet (5 meters). TO INSTALL BATTERIES 1. Open the battery door. Many universal remote controls have a “learning” feature. We recommend you use this feature to program the remote control. For any questions or problems related to programming a universal remote control, you must contact the customer service department of the universal remote control manufacturer for assistance, or refer to the instructions included with the universal remote control. We cannot offer assistance in programming universal remote controls. BATTERY REPLACEMENT When the batteries become weak, the operating distance of the remote control is greatly reduced and you will need to replace the batteries. CAUTION: Danger of explosion if battery is incorrectly replaced. NOTES: • If the remote control is not going to be used for a long time, remove the batteries to avoid damage caused by battery leakage corrosion. • Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable (NICKEL-CADMIUM) batteries. • Always remove batteries as soon as they become weak. • Weak batteries can leak and severely damage the remote control. • Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 2. Insert 2 “AAA” batteries. WARNING : Do not dispose of batteries in a fire. Batteries may explode or leak. + _ + _

REMOTE CONTROL REFERENCE GUIDE REMOTE CONTROL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1. FUNCTION Button Press to switch between TV/AV In/YUV In/ PC In. 2. Number (0 - 9) Buttons 3. [dot] Button Press to enter digital sub-channels (i.e. 11.3 or 12.7) 4. EXIT Button Press to exit the TV SET UP menu and return directly to normal viewing. 5. CURSOR ( , , , ) Buttons Press to highlight selections on a menu screen and adjust certain settings. ENTER Button Press to confirm selections on a menu screen. CH + / CH - Buttons Press to change the TV channels. 6. DISPLAY button Press to show that input you are watching (TV/AV In/YUV In/PC In). 7. VOLUME (- / +) Buttons Press to adjust the volume level. 8. CC Button Press to activate the Closed Captioning feature. This function only works on programs broadcasted with captions. 9. TV Button Press to switch to TV mode. 10. PICTURE Button Press to select from preset screen display settings to match the type of show you are watching (Standard/Soft/Movie/ Personal). 11. STANDBY / ON Button Press to turn ON the unit or put it in STANDBY (OFF) mode. 12. LAST CH Button Press to switch repeatedly between the last two channels displayed. 13. MENU Button Press to display the on-screen TV menu. 14. MUTE Button Press to turn off the sound. 15. MTS Button Press to select between MONO sound, STEREO sound and Secondary Audio Program (SAP). FORMAT Button Press to select the picture format (Wide/ Zoom/Auto/4:3). SOUND Button Press to select from preset sound settings to match the type of show you are watching (Standard/Music/Movie/ Personal). 16. HD Button Press to switch to source connected to YUV in (component) inputs. 17. AV IN Button Press to switch to source connected to AV (composite) inputs.

CONTROL REFERENCE GUIDE FRONT AND SIDE VIEWS 1) Button Turns the unit on and off. 2) MENU Button Enters the on-screen TV menu. 3) FUNCTION Button Selects TV/AV In/YUV In/PC In. 4) CH Buttons Confirms selections on the TV menu screen and changes the TV channels. 5) - VOL + Controls Adjusts the volume level. 6) Color LCD Screen 7) Remote Sensor Receives the remote control signal. 8) Speaker 9) Removable Stand REAR VIEW 10) AC Power Cord 11) VIDEO OUT Jack - AV OUT 12) AUDIO OUT Jacks (Left/Right) - AV OUT 13) VIDEO IN Jack - AV IN 14) AUDIO IN Jacks (Left/Right) - AV IN 15) MONITOR/VGA Jack - PC IN 16) AUDIO Jack - PC IN 17) Component VIDEO IN Jacks (Y/PB/ PR) - YUV IN 18) AUDIO IN Jacks (Left/Right) - YUV IN 19) S-VIDEO Jack - AV IN 20) HEADPHONES Jack 21) TV Antenna Terminal

CONNECTIONS CONNECTING A TV ANTENNA / CABLE / SATELLITE To view television channels correctly, a signal must be received from one of the following sources: - An indoor or outdoor aerial antenna - A cable system - A satellite system CONNECTING AN A/V DEVICE To connect other equipment such as a VCR, camcorder, satellite system or cable, etc.: Connecting a VCR / Camcorder / Satellite System / Cable Connect the AUDIO and S-VIDEO cable (not included) as shown. Make sure you connect the cable from the other equipment (AUDIO OUT and S-VIDEO OUT) to this unit (AUDIO IN and S-VIDEO IN). NOTE: Please refer to the user manual for the other equipment for more information. Connecting a Digital Antenna The tuner in this TV receives ATSC TV signals from an antenna. This digital TV can receive standard (SDTV) and high definition (HDTV) over the air broadcasts. Connecting an Analog Antenna or Device The tuner in this TV receives NTSC TV signals, analog cable signals or the RF output from a satellite receiver, VCR or cable box. Satellite, cable or TV antenna cable to TV ANTENNA terminal (cable not included) To S-VIDEO OUT / AUDIO OUT jacks To S-VIDEO IN jack To AUDIO IN jacks (AV IN)

CONNECTIONS CONNECTING DEVICES WITH A COMPOSITE (YELLOW RCA-TYPE) VIDEO OUTPUT To connect A/V devices such as a VCR, video game system or camcorder: Connecting a VCR / Video Game System / Camcorder Connect the AUDIO / VIDEO cable (not included) as shown. Make sure you connect the cable from the other equipment (AUDIO and VIDEO OUT) to this unit (AUDIO and VIDEO IN). NOTE: Please refer to the user manual for the other equipment for more information. CONNECTING DEVICES WITH A COMPOSITE (YELLOW RCA-TYPE) VIDEO INPUT To connect A/V devices such as a VCR, PVR or camcorder: Connecting a VCR / PVR / Camcorder Connect the AUDIO / VIDEO cable (not included) as shown: Make sure you connect the cable from the other equipment (AUDIO and VIDEO IN) to this unit (AUDIO and VIDEO OUT). NOTE: Please refer to the user manual for the other equipment for more information. To AUDIO / VIDEO IN jacks (AV IN) To AUDIO / VIDEO OUT jacks To AUDIO / VIDEO OUT jacks To AUDIO / VIDEO IN jacks

CONNECTIONS CONNECTING A HIGH-DEFINITION (HD) SOURCE High-Definition (HD) devices with component video output must be connected to the YUV input. Connect the component video cable and audio cable (not included) as shown. Make sure you connect the component video cable and audio cable from the other equipment (COMPONENT VIDEO OUT and AUDIO OUT) to this unit (COMPONENT VIDEO IN and AUDIO IN - YUV IN). NOTE: When connecting a DVD player to the television, the picture resolution is solely dependent upon the resolution supported by the DVD player attached. DVD player resolutions vary from 480i to 1080i, and this unit can support DVD players up to a maximum resolution of 1080i. CONNECTING A PC Connect the 15-pin D-SUB PC/VGA connector from your computer to the 15-pin D-SUB PC/VGA input on this unit using a monitor cable and audio cable (not included) as shown. Make sure you connect the cable from the computer (PC Connector and AUDIO - PC OUT) to this unit (MONITOR / VGA and AUDIO - PC IN). To AUDIO jack (PC OUT) * May require a subscription for receiving HD channels. Check with your cable/ satellite service provider for details. To AUDIO IN jacks (YUV IN) To AUDIO OUT jacks To COMPONENT VIDEO IN jacks (YUV IN) To COMPONENT VIDEO OUT jacks To PC connector

USING HEADPHONES • Turn down the volume before connecting headphones to the unit, then adjust the volume to your desired level. • When headphones are connected, no sound will come from the front speakers. NOTE: Avoid listening to sound at high levels for prolonged periods of time. This may be harmful to you and may cause hearing loss. CONNECTIONS CONNECTING AN AUDIO AMPLIFIER This connection allows you to use an audio amplifier and external speakers. Connect the AUDIO cable (not included) as shown. Make sure you connect the cable from the other equipment (AUDIO IN) to this unit (AUDIO OUT). CONNECTING THE AC POWER CORD • Connect the AC power cord into a wall outlet. • Press the STANDBY / ON button on the left side of the unit or use the remote control to turn on the unit. NOTES: • TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF WALL OUTLET, THEN FULLY INSERT. • When the AC power cord is plugged in, the unit is not completely disconnected from the main power, even when the power is turned off. • Be sure the AC power cord is disconnected and all functions are off before making connections. • Make sure all components are connected correctly. • When you are not going to use the unit for a long period of time, disconnect the AC power cord. • Mains plug is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use. To be completely disconnected the apparatus from supply mains, the main plug of the apparatus shall be disconnected from the mains socket outlet completely. To AC wall outlet Headphones (1/8” [3.5mm] diameter plug) To AUDIO IN jacks To AUDIO OUT jacks

TV SETUP PICTURE MENU 1. Press the MENU button. 2. Press the button to enter PICTURE settings. 3. Use the or button to select the options (Picture Mode, Contrast, Brightness, Sharpness, Tint or Color). Adjust them using the or button (The screen will change to your desired setting). 4. Repeat step 3 to adjust other options. 5. To exit the MAIN MENU and return to the normal screen, press the EXIT or MENU button repeatedly. Note: Some settings on the menu screen may not activate depending on which mode the unit is currently in (TV/AV/YUV/PC). Picture Mode: Select from preset screen display settings to match the type of show you are watching (Standard, Soft, Movie and Personal). Select Personal mode to recall your custom settings on contrast, brightness, sharpness, tint and color. Contrast : Adjust to sharpen the picture quality. The black portions of the picture become richer in darkness and the white become brighter. Brightness : Adjust the brightness of the picture. Brighten or darken the whole picture. Sharpness : Adjust the sharpness level to improve detail in the picture. Tint : Adjust the tint of the picture (Toward purple / Toward green). Color : Adjust the color of the picture. PICTURE PICTURE AUDIO TIME SET UP PARENTAL TV Picture Mode Contrast Brightness Sharpness Tint Color 63 44 38 0 60 Standard UP/DOWN ADJUST "MENU":EXIT AUDIO MENU 1. Press the MENU button. 2. Use the or button to select AUDIO, then press the button to enter the AUDIO settings. 3. Use the or button to select the options (Sound Mode, Bass, Treble, Balance, Audio Language or MTS). Adjust them using the or button. 4. Repeat step 3 to adjust other options. 5. To exit the MAIN MENU and return to the normal screen, press the EXIT or MENU button repeatedly. Sound Mode : Select from preset sound settings (Standard, Music, Movie or Personal) to match the type of show you are watching. Select Personal mode to recall your custom settings on bass, treble and balance. Bass : Adjust the bass range. Treble : Adjust the treble range. Balance : Adjust the balance level toward the left or right speakers. Audio Language : Select from English / Spanish / French (available for digital channels if multiple audio languages are broadcasted). MTS (Multi Channel Television Sound) : Select Stereo / SAP (Secondary Audio Program) / Mono. Note: Experiment with different sound settings until you find the settings you prefer. Note: The SAP (Secondary Audio Programs) feature allows a TV station to broadcast other information, which could be audio in another language. PICTURE AUDIO AUDIO TIME SET UP PARENTAL TV Sound Mode Bass Treble Balance Audio Language MTS 50 50 0 Standard UP/DOWN ADJUST "MENU":EXIT English Stereo PLV36220CS1_12-19.pmd 10/24/2007, 7:47 PM 12

TV SETUP SET UP MENU 1. Press the MENU button. 2. Use the or button to select SET UP, then press the button to enter the SET UP settings. 3. Use the or button to select the options (OSD Language, Color Mode, PC Set Up, Closed Caption or Restore Setting). Adjust them using the or button (The screen will change to your desired setting); or press the button to go into the detailed settings. 4. Press the MENU button to return to the previous menu. 5. Repeat steps 3 and 4 to adjust other options. 6. To exit the MAIN MENU and return to the normal screen, press the EXIT or MENU button repeatedly. OSD (On Screen Display) Language : Select On-screen menu language from English / French / Spanish. Color Mode : Adjust the three color temperature of the picture. Choose from Normal (balanced), Warm (red white), or Cool (blue white) modes. Restore Setting : If you reset the TV to the factory settings, all your present settings on PICTURE and AUDIO will be erased and replaced by the factory’s default settings. PICTURE AUDIO TIME SET UP SET UP PARENTAL TV OSD Language Color Mode PC Set Up Closed Caption Restore Setting English Normal UP/DOWN ADJUST "MENU":EXIT TIME MENU 1. Press the MENU button. 2. Use the or button to select TIME, then press the button to enter the TIME settings. 3. Use the or button to select the options (OSD Duration, Sleep Timer, Time Zone, Day Saving Time or Clock). Adjust them using the or button. 4. Repeat step 3 to adjust other options. 5. To exit the MAIN MENU and return to the normal screen, press the EXIT or MENU button repeatedly. OSD (On Screen Display) Duration : Select the length of time the On Screen Menu is displayed: 15 Sec / 30 Sec / 45 Sec / 60 Sec. Sleep Timer : Select the length of time before the unit automatically changes to Standby Mode: Off -> 5 Minutes -> 10 Minutes -> 15 Minutes -> 30 Minutes -> 60 Minutes -> 90 Minutes -> 120 Minutes -> Off. Time Zone : Select the time zone from Eastern / Central / Mountain / Pacific / Alaska / Hawaii. Day Saving Time : Select On to activate daylight savings time. Clock : Displays the current time. PICTURE AUDIO TIME TIME SET UP PARENTAL TV OSD Duration Sleep Timer Time Zone Day Saving Time Clock 50 50 15 Sec Off Eastern Off 2007/03/05 04:39PM UP/DOWN ADJUST "MENU":EXIT PLV36220CS1_12-19.pmd 10/24/2007, 7:47 PM 13

TV SETUP PC Set Up (in PC mode only) - Resolution : 1680 x 1050 max - Refresh Frequency : 60Hz max H - Pos : Center the image by moving it left or right. V - Pos : Center the image by moving it up or down. Clock : Adjusts the display clock to change width of the image. Phase : Adjusts the image if there is flicker of screen letters, color misalignment, or blurring. Closed Caption CC Mode : Select closed caption On, Off or CC on Mute. Analog Closed Caption : Select the analog closed caption or turn it off. Digital Closed Caption : Select the digital closed caption or turn it off. Digital Caption Style : Select As Broadcaster to use the default digital caption style of the broadcaster. Select Custom to activate the caption style items and set your desired detailed settings. Note: This function only works on ATSC programs broadcast with captions. PARENTAL MENU Password 1. Press the MENU button. 2. Use the or button to select PARENTAL, then press the button to enter the PARENTAL settings. The menu locked screen will be displayed. 3. Enter a 4-digit password. Once entered, the screen will enter the Parental menu. The preset password is 0000. If you forget the password, enter " 8888 " to unlock parental control. SETUP SETUP H - Pos V - Pos Clock Phase Auto adjust UP/DOWN ADJUST "MENU":EXIT 50 50 50 100 Best Resolution is 1680x1050 PICTURE AUDIO TIME SETUP PICTURE AUDIO TIME SET UP SET UP PARENTAL TV CC Mode Analog Closed Caption Digital Closed Caption Digital Caption Style CC on Mute CC1 Service1 UP/DOWN ADJUST "MENU":EXIT PICTURE AUDIO TIME SET UP PARENTAL PARENTAL TV Enter Password UP/DOWN ADJUST "MENU":EXIT PLV36220CS1_12-19.pmd 10/24/2007, 7:47 PM 14

TV SETUP Rating Enable: Select On to edit the following parental items. Select Off to disable parental control. US : Set TV and MPAA ratings. Canada : Set Canada English and Canada French ratings. RRT Setting : Set Rating Region Table. Reset RRT : Reset Rating Region Table to the default settings. Parental 1. Use the or button to select various Parental settings. Adjust them using the or button, or press the button to go into the detailed settings. 2. Press the MENU button to return to the previous menu. 3. Repeat steps 1 - 2 to adjust other options. 4. To exit the MAIN MENU and return to the normal screen, press the EXIT or MENU button repeatedly. TV-Y : Recommended for all children. TV-Y7 : Recommended for all children age 7 and above. TV-G : General Audience. TV-PG : Parental Guidance Suggested. TV-14 : Parental Strongly Cautioned. TV-MA : Mature Audience Only. N/A : Not rated. G : GENERAL AUDIENCES, Suitable for all ages. PG : PARENTAL GUIDANCE SUGGESTED - Some material may not be suitable for children. PG-13 : PARENTS STRONGLY CAUTIONED - Some material may be inappropriate for children under 13. R : RESTRICTED, Under 17 requires accompanying parent or adult guardian for viewing in movie theaters. NC-17 : No one 17 or under admitted in movie theaters, X : Adults Only. E : Exempt. C : Children. C8+ : Recommended for children age 8 and older. G : GENERAL AUDIENCES, Suitable for all ages. PG : PARENTAL GUIDANCE SUGGESTED - Some material may not be suitable for children. 14+ : Viewers 14 years and older. 18+ : Adult Programming. E : Exempt. G : GENERAL AUDIENCES, Suitable for all ages. 8 ans+ : Not recommended for young children. 13 ans+: Not suitable for children under the age of 13. 16 ans+: Not suitable for children under the age of 16. 18 ans+: Adult Programming. U.S. MPAA Ratings U.S. TV Ratings Canadian English Ratings Canadian French Ratings PICTURE AUDIO TIME SET UP PARENTAL PARENTAL TV Change Password Rating Enable US Canada RRT Setting Reset RRT On UP/DOWN ADJUST "MENU":EXIT PLV36220CS1_12-19.pmd 10/24/2007, 7:47 PM 15

TV SETUP Antenna : Air (over-the-air broadcasts, Ch 2-69) or CATV (cable/satellite broadcasts, CH 1-135) mode is available. Auto Scan : Search for usable stations and store them in memory. Auto Scan Add CH : Search for more usable stations and add them in memory. The stations stored before are still kept. Channel Skip : Skip weak channels and the channels you do not like. Channel No. : Select a different TV channel. Channel Label : Display and edit the channel label. DTV Signal : Display the signal strength (for digital TV channels only). TV MENU (For TV Mode Only) 1. Press the MENU button. 2. Use the or button to select TV, then press the button to enter the TV settings. 3. Use the or button to select the options (Antenna, Auto Scan, Auto Scan Add CH, Channel Skip, Channel No., Channel Label or DTV Signal). Adjust them using the or button, or press the button to go into the detailed settings. 4. Press the MENU button to return to the previous menu. 5. Repeat steps 3 and 4 to adjust other options. 6. To exit the MAIN MENU and return to the normal screen, press the EXIT or MENU button repeatedly. Channel Skip 1. Use the or button to select a channel (Press the button to select the last channel of the page; press again to go to the next page. Press the button to select the first channel of the page; press again to go to the previous page). 2. Press the ENTER button to shift between On / Off (Select On to skip the selected channel. The channel will not appear when you press the CH / CH Button). Channel Label You can edit a label for each channel. 1. Use the or button to select the number or letter. Use the or button to move and edit the next character. Press the ENTER button to confirm. 2. After editing, the Channel and Channel Label will be displayed on the screen when you press the DISPLAY button. PICTURE AUDIO TIME SET UP PARENTAL TV TV Antenna Auto Scan Auto Scan Add CH Channel Skip Channel No. Channel Label DTV Signal Air 5-5 XXX UP/DOWN ADJUST "MENU":EXIT Good PICTURE AUDIO TIME SET UP PARENTAL TV TV "MENU":EXIT "ENTER":SELECT Skip On On Off Off Off On Off No. 3 2 4 5 5-1 6 7 Program Name XXXX XXX XX XX XXXX XXXXX XXXX PICTURE AUDIO TIME SET UP PARENTAL TV TV EDIT SELECT "MENU":EXIT X PLV36220CS1_12-19.pmd 10/24/2007, 7:47 PM 16

MAINTENANCE CLEANING THE UNIT • Be sure to turn the unit off and disconnect the AC power cord before cleaning the unit. • Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been dipped in a weak soap-and-water solution and wrung out thoroughly. Then wipe it with a dry cloth. • Never use alcohol, benzene, paint-thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust. TROUBLESHOOTING GUIDE SYMPTOM CAUSE (AND REMEDY) The remote does not function. • Make sure the AC power cord is connected. • The unit is not turned on. No power. • Remove any obstacles between the remote and the unit. • Use the remote near the unit. • Point the remote at the remote sensor on the unit. • Replace the batteries in the remote with new ones. • Check the location of the antenna and adjust it if necessary. • Make sure the antenna cable is firmly connected. • Make sure all input cables are firmly connected. TV Bad Picture (snow, multiple images, distortion, blurry) • Check the PICTURE MENU within the TV SETUP MENU. • Check to make sure the program you are watching is broadcast in Color and not black and white. Black and white picture. • Make sure the unit is plugged in and turned on. • Make sure TV mode is selected. • Try a new channel to check for possible station trouble. • Make sure the antenna is connected properly. • Increase the volume. • Make sure the antenna or audio video source device is working properly. • Make sure all cables are firmly connected. • Check for local interference. No picture or sound. • Make sure there are no unshielded electrical devices nearby that are causing interference. • Turn the unit off for 30 minutes, then try it again. Colored patches of picture. PLV36220CS1_12-19.pmd 10/24/2007, 7:47 PM 17

811-362291W060 VENTURER ELECTRONICS (“VENTURER”) makes the following limited warranty. This limited warranty extend to the original consumer purchaser and is limited to non-commercial use of the product. Ninety (90) Day Parts & Labor Warranty VENTURER products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of ninety (90) days from the date of their original retail purchase. If the unit fails to conform to this warranty, we will service the product using new or refurbished parts and products, at VENTURER’s sole discretion. During a period of ninety (90) days from the effective warranty date, VENTURER will provide, when needed, service labor to repair a manufacturing defect at its designated Service Center. To obtain warranty service in the Untied States, you must first call our Customer Support Center at (800) 252-6123, during the hours listed in the box below. The determination of service will be made by VENTURER Customer Support. PLEASE DO NOT RETURN YOUR UNIT TO VENTURER WITHOUT PRIOR AUTHORIZATION. New or remanufactured replacements for defective parts or products will be used for repairs by VENTURER at its designated Service Center for ninety (90) days from the effective warranty date. Such replacement parts or products are warranted for an additional ninety (90) days from the date of repair or replacement. The Customer will be required to ship the unit to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs. The customer is responsible for all transportation charges to the service facility. Packaging and Shipping Instruction When you send the product to the VENTURER service facility you must use the original carton box and packing material or an equivalent as designated by VENTURER. LIMITED WARRANTY Your Responsibility (1) You must retain the original sale receipt to provide proof of purchase. (2) These warranties are effective only if the product is purchased and operated in the U.S.A. or Canada. (3) Warranties extend only to defects in material or workmanship, and do not extend to any product or parts which have been lost or discarded, or damage to product or parts caused by misuse, accident, improper operation or maintenance, or use in violation of instructions provided with the product, or to product which has been altered or modified without authorization of VENTURER, or to products or parts thereof which have had the serial number removed or changed. Out of Warranty In the event your product requires repair after the limited warranty period has expired, please contact our Customer Support Center at 1-800-252-6123 or www.venturer.com. Hours: Monday–Thursday: 9–7, Friday: 9–5, Saturday: 9–12 EST. Important: You are responsible for any transportation, shipping or insurance relative to the return of product to our Product Returns Center. All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall VENTURER be liable for consequential or incidental damages. No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any manner whatsoever. The time within action must be commenced to enforce any obligation of VENTURER arising under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to ninety (90) days from the date of purchase. This limitation does not apply to implied warranties arising under state law. This warranty gives you specific legal rights and you may also have other rights, which may vary, from state to state. Some states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you. For more information on other products and services, please visit our web site at www.venturer.com Important: Also keep your “Bill of Sale” as proof of purchase. Model no. .............................................. Product name ............................................................... Type of set ........................................................................................................................................ Serial no. ................................................ Invoice no. ..................................................................... Date purchased ..................................... Dealer name ................................................................. © 2007 VENTURER Electronics Inc. PLV36220CS1_12-19.pmd 10/24/2007, 7:47 PM 19