Rompa 19280 Quick Start Manual

Copyright ROMPA ® Ltd SUPA SWITCH CONSOLE BY ROMPA 19280, KH 11.10 SUPA SWITCH CONSOLE BY ROMPA® 19280 CONTENTS 1 x Console (padded base) 1 x Bubble Tube Please note: This switch will not control the early models of ROMPA® Bubble Tubes. This product does not include a collar. You may wish to use a collar to secure your bubble tube to the wall. The collar 14694 is appropriate for these bubble tubes. ASSEMBLY 1. Carefully unpack all the components. 2. Take the padded top off the Console. This is attached by Velcro. Pull the padded top off firmly to release the Velcro. 3. You now should be able to see the ‘trap doors’. These are held in place by cross-head screws in the corners. Release all the screws and lift the trap door out. Take care as these contain staples and the wood used is a little rough. 4. Attach the Bubble Tube tube to the chassis inside the Console. The chassis is the metal box with a screw and washer in each corner. First release the screws and washers then align the bottom of the tube with these holes. Replace the screws and washers once the tube is aligned. 5. Attach the brown plastic pipe, which is already attached to the pump, to the bottom of the Bubble Tube column.

Copyright ROMPA ® Ltd SUPA SWITCH CONSOLE BY ROMPA 19280, KH 11.10 6. Connect the end of the white cable (with the telephone-type plug) to the socket (J) on the chassis as shown below. 7. Connect the black power supply box (shown below) to the round socket (H) in the bubble tube chassis. The power supply should be placed above water level – ideally this should be wall mounted out of reach. The lead from the other end of the power supply needs to be plugged in to a wall socket. There is no ON/OFF button on the power supply. The green LED light will be lit. There may be a slight delay.

Copyright ROMPA ® Ltd SUPA SWITCH CONSOLE BY ROMPA 19280, KH 11.10 8. The unit will begin to flash, displaying a sequence of coloured lights, and bubbles will begin to rise up the tube. Turn the wheel (I) on the white Base Cover to adjust the speed of the light change. Please note: The Connector marked J is for the 17274LED Super Interactive Switch Box only. Connecting any other cable to this socket may cause permanent damage to the Bubble Tube. The Connector marked K is for the USB cable only. Connecting any other cable to this socket may cause permanent damage to the Bubble Tube. Ensure that water does not come into contact with the electronic circuit boards in the base of the Bubble Tube. Please take extreme care when filling/emptying the Bubble tube to ensure that the electronics remains dry. H I K J LED Light Dust Protector Cover in socket J H

Copyright ROMPA ® Ltd SUPA SWITCH CONSOLE BY ROMPA 19280, KH 11.10 9. Look inside the console to find the small triangular cut-out along the floor edge – pass the power supply cable through this to make sure it does not get trapped. 10. Check the lights are working before filling with water. Place the Console in its final position as a Bubble Tube should not be moved when full. The Bubble Tube should now be placed on a stable, level surface in preparation to be filled with water. If the surface is not flat, the pump is likely to create more noise than a gentle background ‘humming’. 11. Fill with water carefully until the required level is achieved. This should be approximately 2” from the top of the tube. The water level will rise when filled with water. Place the bubble tube cap (lid) on top of the bubble tube. 12. Plug in the power supply at the wall and switch on. Make sure that the protective plastic sheet is over the circuit board to protect it from accidental spills and splashes. 13. Replace the trap doors and their screws, making sure these are the right way round - the Velcro forms a rectangle. 14. Replace the padded top of the Console, making sure it is the right way round – the hole is aligned with the hole in the Console. OPERATION 1. Press the central button (orange) on the control panel to stop/start bubbles. This button does not change the colour. 2. Press a coloured button to change the colour. 3. Adjust the controls on the front of the Console as required e.g. to change the length of time a colour remains on or if the bubbles are on/off till the central button is pressed. SAFETY 1. The Bubble Tube is suitable for use on a level horizontal floor. Do not attempt to move the Bubble Tube when it is full of water. 2. Always supervise the use of this product. 3. Regularly change the water and use a suitable water cleansing agent. 4. For indoor use, in dry environments. CARE AND MAINTENANCE TO EMPTY THE BUBBLE TUBE 1. Use an appropriate pump. Remove the cap (round lid at the top of the tube) and remove the water from the top of the tube using your pump. A pump is available separately from ROMPA®: code 20601. From November 2011, ROMPA® Bubble Tubes no longer have a drain hose at their base. 2. Refill the Bubble Tube. GENERAL CARE 1. Wash the exterior of the Maxi Bubble Tube with a slightly soapy cloth. Wipe excess soap away with a damp cloth. NOTE: Never use solvents or liquid detergents inside the Bubble Tube.

Copyright ROMPA ® Ltd SUPA SWITCH CONSOLE BY ROMPA 19280, KH 11.10 2. Since prevention is better than cure, we recommend the following: • To prevent the growth of microbes in the water: - Change the water monthly (use an appropriate pump to siphon out water) - Empty the tube altogether if it is not to be used for long periods - A suitable water sterilising tablet can be added to the water – consult your local Health and Safety Executive for guidelines (do not use with Ball Bubble Tubes as this could discolour the balls) - Do not add bleach, coloured dyes or salt to the water • To prevent the bubble tube from being knocked over we recommend the use of a collar (14694 for 15cm tubes). This should be secured to a wall with adequate fixtures. • To prevent lime-scale blocking component parts in hard water areas use an appropriate water softener as required. SPECIFICATION Pump: 12 Volt 50/60 Hz, Schwarzer Prazision, type SP 203 S. Power Supply 240 Volt (U - 110V) 110V Output 12V AC 60W 240V Output 12V AC 60W The power supply is UL listed – E1494743G58, and meets the requirements of BS EN61558-1 and BS EN61558-2-6 TROUBLE SHOOTING BUBBLE TUBE In the unlikely event of product failure, please check the following: Problem: No lights, no bubbles • Check that the bubble tube is plugged in at the wall • Check that the cable to the bubble tube is connected to the jack socket (as shown above) • Check that the telephone type plug from the white cable is correctly connected to the chassis as shown above. • Check that the two white plugs (shown right) that are attached to the circuit board are still connected. The circuit board is fixed to one side of the console Problem: Lights but no bubbles and very noisy • Check all pipes are firmly connected and free of kinks/bends. Check the pipes have not worked free – occasionally vibrations/transportation can loosen pipes. Further copies of these instructions can be downloaded at www.rompa.com We hope you find our instructions invaluable. If you have any suggestions for improving them further your comments will be greatly received – please contact us at [email protected]