Performance Tool W5194 Owner's Manual

Stock Number W5194 OWNER’S MANUAL For your saFety, please read these instructions carefully and retain them for future use. LIMIteD WarraNty PERFORMANCE TOOL extends only the following warranties, and only to original retail purchasers. These warranties give specific legal rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of warranties and remedies. There may be other rights which vary from state to state. PERFORMANCE TOOL warrants the product to be free from defects in materials and workmanship under normal use and service. A defective product may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to place of purchase immediately after discovery of defect. After 90 days and up to 1 year from date of purchase, PERFORMANCE TOOL will replace at no charge any parts which our examination shall disclose to be defective and under warranty. These warranties shall be valid only when a sales receipt showing the date of purchase accompanies the defective product or defective part(s) being returned. For part(s) after 90 days, please remit your request, postage prepaid to PERFORMANCE TOOL, P.O. Box 24086 Seattle, WA 98124 These warranties exclude blades, bits, punches, dies, bulbs, fuses, and other consumables which must be replaced under normal use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not design or which has been repaired or altered in any way so as to affect adversely its performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse, neglect, accident or wear and tear incident to normal use and service. PERFORMANCE TOOL does not authorize any other person to make any warranty or to assume any liability in connection with its products. Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL makes no express or implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL makes no implied warranty of merchantability and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for personal, family or household use and not for commercial or business use, PERFORMANCE TOOL makes an implied warranty of merchantability (and, if otherwise applicable, an implied warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the duration, expressly warranted above. The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in all cases. PERFORMANCE TOOL shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the repair, or replacement thereof as provided above. The laws on limitation of remedies or on consequential, incidental or special damages may vary from state to state, so the above limitations may not apply in all cases. Copyright ©2008 PerForMaNCe tooL – all rights reserved WarNING: This product and its packaging contain a chemical known to the State of California to cause cancer, birth defects or other reproductive harm. Always wear eye protection when using tools.

5 4 1 3 2 6 7 1. Attach upright supports (#3) to bottom feet (#1). 2. Connect brace supports (#2) to upright supports (#3) and bottom feet (#1). 3. Attach the 4 cross braces (#4) to the upright supports (#3) at brackets. NOTE: Ensure that all cross brace holes are in the same location for attaching center supports (#5). 4. Connect center supports (#5) to cross braces (#4). 5. Insert bar caps (#7) into bottom feet (#1) and upright supports (#3). No. Description Qty. 1 Bottom Feet 2 2 Brace Supports 2 3 Upright Supports 2 4 Cross Braces 4 5 Center Supports 3 6 Phillips Head Screws 20 7 Bar Caps 6 SPECIFICATIONS NOTE: Specifications are subject to change without notice. Small Bins: .................... 16 (5-1/2" x 3-1/4") Large Bins: ................... 10 (8-1/4" x 3-1/4") Rack Height: ......................................26" Tall Rack Width: ....................................36" Wide Rack Depth: ................................... 12" Deep Construction: .............. Powder Coated Steel