Mountup MU6002 Instruction Manual

Instruction Manual If you have any questions , please contact us. MU6002 V2.0 75x75 100x100 (2~8kg)x2 (4.4~17.6lbs)x2 32"

this product, please contact us. Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specifed in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use. This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED. NOTE: Not all hardware included will be used. WARNING! PACKAGE CONTENTS E (x1) Bracket F (x1) Clamp I (x1) Grommet Base L (x2) Bolt K (x1) Carriage Bolt N (x1) 3mm Allen Key O (x1) 4mm Allen Key P (x1) 6mm Allen Key G(x5) M6x10 H(x4) Pad D (x2) VESA Plate 01 M (x1) Support Plate DO NOT EXCEED WEIGHT CAPACITY. (17.6lbs)x2 (8kg)x2 J (x1) Wingnut M-C (x8) D6 Washer M-A (x8) M4x12 M-B (x8) M6x12 M-D (x8) spacer A (x2) Upper Arm B (x2) Lower Arm C (x1) Base

Mount Bracket (E) to Base Bottom (C) with Bolts (G). Bolts could be tightened by the 4mm Allen Key (O). Similarly, attach Clamp (F) to Bracket (E) with Bolts (G) and 4mm Allen Key (O). Adjust the Clamp width to ft with desk. Secure stand to desktop by tightening Clamp (F) or by Allen key (P). G O O G 10-60mm 10-90mm F F E C E E E G O OR STEP 2: Clamp Installation or Grommet Base Installation STEP 1: Apply Pads to the Base Bottom H Apply pads (H) to the base bottom to avoid desk scratches. C P OR

03 OPTION B: Grommet Base Installation For grommet hole mounting, place Carriage Bolt (K) through the center of Grommet Base (I). Mount Grommet Base to Base Bottom (C) with Bolts (G) and tighten by 4mm allen key (O). Run Carriage Bolt (K) through Grommet Hole on desktop. Attach Support Plate (M) and Wingnut (J). Last step, tighten Wingnut (J). O C I G K M J 10-90mm

using Allen key (N). STEP 3: Arm Installation Note: Please note that the side with the label“ ” is installed on the base(C) when installing the lower arm(B) to the base (C). DO NOT tighten the screw excessively or it might be stripped. DO NOT tighten the screw excessively or it might be stripped.

D D M-A M-B M-C P M-A M-B M-C M-D P OPTION A: Flat Back Monitor Attach the VESA plate (D) to back of monitor and secure with screws(M-A)or(M-B) with washers(M-C) using 6 mm Allen Key (P). Do not tighten the screws excessively or your monitor might be damaged. CAUTION:To select the correct screws(M-A or M-B) for your monitor, you can try to screw it on your monitor by hand. The one can screw inside is the correct screw for your monitor. OPTION B: Curved Back Monitor Attach the VESA plate (D) to back of monitor and secure with screws (M-A) or (M-B) with washers (M-C)and spacers(M-D)using 6 mm Allen Key (P). Do not tighten the screws excessively or your monitor might be damaged.

bolt is installed before you rotate the monitor. STEP 5: Hang Monitor Tilts down Note: 1. Loosen the tilting bolt. 2. Adjust monitor to your desired tilting angle. 3. Retighten the tilting bolt to P spring arm falls down greatly. L Important Notice: The gas spring is pre-set to minimum tension. Once the monitor is hanged on, hold the monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the monitor in a slow & gentle way while observing whether the arms will fall down wildly. Guideline to adjust monitor tilting angle.

P Note1: Be sure to keep the arm in horizontal position during adjustment. Falls down Turn counter-clockwise(“+”direction) to increase gas spring tension until the monitor can stay at the desired height by itself. Turn clockwise(“-”direction) to reduce gas spring tension until the monitor can stay at the desired height by itself. Rises up CAUTION Monitor Weight 2kg 3kg 4kg 5kg 6kg 7kg 8kg Circles (AT LEAST) For proper functioning of this mount, depending on diferent weight of monitor you might need to adjust tension in upper arm (A) using 6 mm allen key (P). 1 4 8 11 14 17 min As for how many circles the screw should be turned, refer to below diagram. Note2: If the monitor falls down and fails to stay at the desired height by itself: If the monitor rises up and fails to stay at the desired height by itself:

08 STEP 7: Cable Management Run cables from monitor through bottom of gas spring arm. Reattach plastic covers as shown in diagram. Remove bottom plastic covers from gas spring arm as shown in diagram.

09 DESK DESK Pay attention while clamp install ! 180° 360° +90° -45° 360° 270° Adjust monitor position and rotation.

Product Dimensions 10 6.3“ 55mm 2.2“ 2.5“ 6.9"-16.9" 7.87"-11" 270° 360° 180° -45° +90° 160mm 200mm-280mm 63mm 75mm 2.95" 3.94" 4.5" 100mm 114mm 75mm 100mm 114mm 2.95" 3.94" 4.5" 9.4" 240mm 0.39-3.5" 3.9" 100mm 10-90mm 175-430mm 360°

• Never allow children to climb, stand, hang, or play on any part of monitor or stand. • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. • Check that the bracket is secure and safe to use at regular intervals (at least every three months). If you have any questions, please contact us.