TKH security FD950 Quick Start Manual

FD950 5MP Vandal Fixed Dome Camera Quick Start Guide Unpack Installation Notices Connectors Connector Definition Camera Cabling Alarm I/O and RS-485 Connection Find additional manuals, the datasheet, the EU Declaration of Conformity, and the latest firmware for this product at: tkhsecurity.com CAUTION INSTALLATION SHALL BE PERFORMED BY QUALIFIED PERSONNEL ONLY. INSTALLATION SHALL BE IN ACCORDANCE WITH LOCAL PROCEDURES. THE CAMERA CONTAINS BATTERIES. DO NOT REPLACE IN RISK OF EXPLOSION. BATTERY REPLACEMENT SHALL NOT BE APPLIED IN VIEW OF THE RISK OF EXPLOSION. LE REMPLACEMENT DES PILES NE DOIT PAS ÊTRE APPLIQUÉ AU RISQUE D'EXPLOSION. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.. FOR “PoE” INPUT CONNECTION, USE ONLY WITH UL LISTED I.T.E WITH “PoE” OUTPUT. DESCRIPTION FOR THE “PoE” IS INTENDED TO BE CONNECTED TO NOT EXPOSED (OUTSIDE PLANT) NETWORKS OR EQUIVALENT STATEMENT IN INSTALLAION INSTRUCTIONS. POUR LA CONNEXION DâÇÖENTREE "PoE", UTILISER UNIQUEMENT AVEC UN I.T.E. LISTE AVEC UNE SORTIE "PoE". LA DESCRIPTION DE "POE" EST CONÇUE POUR ÊTRE CONNECTÉE À DES RÉSEAUX OR NON ÉNONCÉS (INSTALLATIONS EXTÉRIEURES), DANS LES INSTRUCTIONS D’INSTALLATION DE L’INSTALLATION. Subject to modification. Actual product and accessories may differ in appearance. FD950 IT IS NOT RECOMMENDED TO CONTINUOUSLY (24/7) RECORD WITH THE MICRO SD CARD, AS THE CAMERA MAY NOT SUPPORT LONG-TERM CONTINOUS DATA READ/WRITE. CONTACT THE MANUFACTURER OF THE MICRO SD CARD FOR INFORMATION REGARDING THE RELIABILITY AND THE LIFE EXPECTANCY. Figure 1 Camera Connectors See the diagram and the pin definition below for the audio and alarm I/O connection. Figure 2 Diagram of I/O connection pins Pin Definition Pin Definition 1 Audio In L 6 Alarm Out + 2 Audio In R 7 Alarm Out - 3 GND 8 Alarm In + 4 Audio Out L 9 Alarm In - 5 Audio Out R Table 3 Pin definitions for Alarm I/O and RS-485 connection Table 1 Connector definition ❑ The green link LED is lit when there is a good network connection. ❑ The orange network LED flashes to indicate that there is network activity. IN SOME CASES, AN ETHERNET CROSSOVER CABLE MAY BE NEEDED WHEN CONNECTING THE CAMERA DIRECTLY TO THE PC. CHECK THE STATUS OF THE LINK INDICATOR AND THE ACTIVITY INDICATOR LEDS. IF THE LEDS ARE UNLIT, CHECK THE LAN CONNECTION. Power Connector (DC 12V/AC24V) Table 2 Pin definition for power connection Pin Definition 1 AC24V + 2 AC24V - 3 DC12V + 4 DC12V - Quick Start Guide Plastic Screw Anchor(x2) 4-pin power terminal block DC 12V Power Connector M4 Self-tapping screw(x2) Cable Gland Security Torx BNC Connector No. Connector Definition 1 RJ-45 Port (Contact Siqura for a compatible PoE injecter.) For network and PoE connections 2 BNC For analogue video output 3 Power(DC 12V/AC 24V) Power Connection 4 Reset Button Press the button with a proper tool for at least 20 seconds to restore the system. 5 Micro SD Card Slot Insert the SD card into the card slot to store videos and snapshots. Do not remove the SD card when the camera is powered on. 6 Alarm & Audio I/O Alarm I/O & Audio connection + 1 - 2 + 3 - 4 1 2 3 4 5 6 7 8 9 2021 | Vision 1 (20210531) | FD950 QSG

1st time camera login Browser-based Viewer Figure 4 shows the main page of the IP camera user interface. Accessing the Camera Install browser-based viewer IP = 10.1.1.1 Netmask: 255.0.0.0 Auto detect with SDM2 Install browser-based viewer Tkhsecurity.com Enter to the camera product page, Link & Download section If the web interface is not showing video, you might to open your firewall or set the OCX protocol to RTP-over-RTSP(TCP) IP = 10.x.y.z Network Switch DHCP 1 2 3 SDM2-vx.xx-setup.zip Look for SDM2 1 Admin Admin1234 2 Set strong password qwer1234 x6W@oM0a!9#F 3 x6W@oM0a!9#F 4 11 Note 1: If the IE web interface is not showing video, you might need to open your firewall or set the OCX protocol to RTP-over- RTSP(TCP). Figure 4 Main page IP camera user interface 2021 | Vision 1 (20210531) | FD950 QSG