Saveo Scan M12D-BH Manual 

underside of the scanner. On the underside of the scanner you will fnd a small recessed button. Use a pen or paper clip to push the button until you hear a notifcation sound. Ensure power switch remains depressed after you release it. Power on Saveo Scan Switch on and Charge your Scanner Please switch on your scanner (as illustrated) and place it in the cradle to charge for 3~4 hours before frst use. If you want to charge smartphone and scanner simultaneously, please switch scanner to right “C” (charge mode) before placing it in the cradle. *Please remove the protective sticker from window before use Trigger/Power On button Wrist Strap Universal Holder Exit Window Operating Elements LED indicator Charging Cradle Switch for Operation Mode and Charge Mode/Bluetooth Mode Micro USB Cable Use Micro USB cable to connect to smartphone/tablet SAVEO-SCAN-M12D-BH Extend retractable arm Press button and slide outwards to extend the arm Attaching your smartphone to scanner using the universal holder Extend the retractable arm before placing phone in holder and then pushing it frmly back against the phone. Secure phone in holder Insert phone Attach your smartphone 1 2 3 Connect phone to scanner with Micro USB As USB connection locations vary on diferent models of smartphone, the cable can be confgured for your specifc model. For iOS devices, please attach the appropriate adapter to connect to your device.

Switch scanner to Operation Mode (Data trans- mission via USB OTG) Switch to left: Operation Mode/ Data transmission Confrm scanner is connected Saveo Scan is detected by your smartphone as an external keyboard. A message will appear on screen to notify you that a USB device has been connected. You are now connected. Start scanning. Scan the Wired USB OTG Communication barcodes below Demo %W%I%R Demo %E%R%A Connecting via Bluetooth Enable Bluetooth on your device Go to your phone’s homescreen and fnd “Settings”, then “Bluetooth” and turn Bluetooth on. Switch scanner to Charge Mode/Bluetooth Mode Scan the Wireless BT Communication barcodes below Demo %W%L%T When Bluetooth is enabled, the LED will remain red until the scanner has been paired with a Bluetooth device. Switch to right: Charge Mode/ Bluetooth Mode Demo %E%R%A Scan Bluetooth Profle Barcodes below After you scan the Bluetooth profle barcodes below, your scanner will become visible to Bluetooth enabled devices within range. Demo %H%I%D HID Profle A1 A2 Demo %B%R%C Search for devices Your phone will automatically search for devices, Saveo Scan will appear as an external keyboard with a unique identifer number (R-xxxxxx). Select R-xxxxxx to connect Please note: devices only need to be paired once. When they are within Bluetooth range they will automatically attempt to connect to each other. If you wish to pair to another device it is recommended you frst unpair this device. You are now connected. Start scanning. 4 5 6 Please note: The scanner should only be paired with one device at a time. Before you pair your scanner to another device, please frst unpair it from the device in use. Otherwise it will appear on your list of “Available Devices” but will not connect. In this case, please refer to “Unpairing your device” in this guide. Select scanner from “Available Devices” and wait for pairing process to complete. Devices are now paired Once “Connected” is displayed, your device is paired to the scanner. Your scanner is now ready to use.

sion mode and Data Storage Mode. Scan the appropriate barcodes when switching between these two modes. Please note: Switching between modes will wipe the scanner’s internal memory. Operating Modes Data Transmission Mode (Default) Our Default setting is Data Transmission mode. In this mode data will be sent to smartphone/tablet directly. To enter Data Transmission Mode please scan the follwing barcodes. Demo %E%R%A Demo %M%A%F Enter Data Transmission Mode Green/Orange LED fashes followed by 3 beeps. Demo %M%A%N Data Storage Mode In this mode, data will be saved directly to scanner’s memory. Scan Transmit Memory Data to receive data stored on scanner’s internal memory. Enter Data Storage Mode Green/Orange LED fashes followed by 3 beeps. Demo %E%R%A To enter Data Storage Mode please scan the follwing barcodes. 7 8 9 Demo %E%R%A Clean Memory Data Green/Orange LED fashes followed by 3 beeps. Demo %R%E%C Transmit Memory Data Green/Orange LED fashes followed by 3 beeps. Transmit Memory Data Scan the following barcode to receive data stored in the scanner’s internal memory.. After data is transmitted to your device it remains on the scanner’s internal memory. Scan the following barcode to clear the memory if you do not wish to send this data again. Reset Confguration to Defaults (scan from A1 to A4) A1 A2 Reset to Defaults Demo %E%R%A When the battery power is too low, the Orange LED will fash and beep once. Scanner should be charged immediately. If scanner shuts down it is recommended to charge it fully then power it back on. Under power-saving mode, there will not be an LED indication when charging. Orange LED ON Full charged Orange LED (Flashing) Charging / Low battery Red LED ON Ofine / Out of Range Green LED ON Good read Orange LED ON Good read (Batch mode) LED Indicator Information LED Indicator Demo Current Battery Level Scan to receive the current battery level Scan the following barcode to send battery level information to your device. The format is outlined in the table below. %^4^% 80% - 100% %^3^% 55% - 80% %^2^% 30% - 55% %^1^% 10% - 30% %^0^% under 10% Battery Level Status A3 A4 Demo %H%I%D Demo %B%R%C Sound Settings Scan the barcodes to select whether or not the decoder issues a beep signal after a good decode. If selecting Do Not Beep after Good Decode, beeper signals are issued during parameter menu scanning and to indicate errors. Enable (default) Disable

scanner to sleep after 1 minutes inactivity. To wake up the scanner press the trigger. Demo %P%D%T00 Disable Scan to disable power saving mode Demo %P%D%T01 Below are the barcodes to disable/enable power saving mode. Power Saving Mode Reading Mode The default setting for reading mode is Single Scan. To choose another mode please scan the appropriate barcodes below. Motion Sensor: Full Auto Mode In this mode the scanner attempts to decode when it senses motion. Single Scan (Default) In this mode the scanner attempts to decode when the scan button is pressed. Demo Demo 10 11 Transmission Speed Transmission speed is dependent on your device. In order not to lose data please choose the correct speed. Mid Speed is the default. Mid Speed Transmission (Default) High Speed Transmission Low Speed Transmission Demo %B%T%H Demo Demo %B%T%L Before connecting the scanner to another device it is recommended you frst unpair from the current device. Go to the Bluetooth menu on your phone and select the option menu for scanner from list of paired devices. Choose “Forget this Device”/”Unpair” Unpairing your device 12 1 Minute Enter Power Saving Mode after 1 minutes inactivity 5 Minute Enter Power Saving Mode after 5 minutes inactivity 15 Minute Enter Power Saving Mode after 15 minutes inactivity 30 Minute Enter Power Saving Mode after 30 minutes inactivity Mobile Phone/Display Mode This mode improves bar code reading performance with target bar codes displayed on mobile phones and electronic displays. Disable (default) Enable