Ubisense AngleID Quick Start Manual

AngleID™ Quick Start Guide AngleID™ Quick Start Guide AngleID™ Quick Start Guide Product Overview Product Overview Product Overview Product Overview AngleID is a completely new way of doing accurate long-range zone detection and tracking, using RFID. The AngleID reader detects ultra-wideband pulses from tags to precisely determine the angle between a tag and reader and locates the tag in up to eight different 3D zones simultaneously, reporting entry and exit events from each zone to a connected control system. AngleID has a number of uses in many industries including manufacturing, logistics and transportation such as forklift and AGV tracking, dock door management and wireless tool management on production lines. You can control multiple devices by using a single AngleID reader. About this Guide This guide explains how to set up your AngleID reader and configure the detection zone for a tag. This guide assumes that you are familiar with operating and connecting computer systems and networks. What’s in the Box? What’s in the Box? What’s in the Box? What’s in the Box? AngleID Reader Mount your reader in the area where the tag must be tracked. Mounting Bracket Use this bracket to mount your reader. The bracket contains an Installation Support Kit Instruction Sheet that explains how to fix your reader to a suitable surface. Setup Tag Use the supplied tag to configure the zones of your AngleID setup. Reader Features Reader Features Reader Features Reader Features Before you Begin Before you Begin Before you Begin Before you Begin Register your Reader Register your AngleID reader at the URL provided in your AngleID kit. The registration process activates your warranty and then allows you to download: • The AngleID Configuration Tool, which provides a graphical user interface for configuring your reader. • The AngleID Product Key, which enables the Configuration Tool to identify the reader that you have purchased. Ensure that you also have… • A Power Over Ethernet (PoE) source to power-up your reader. • A Windows® configuration PC (with Administrator privileges) to run the Configuration Tool. • A network switch to connect the reader and your PC to the same network. • Cat5 (or higher) Ethernet cables for connecting devices. A Status LED. Turns solid green after booting. B Network Status LEDs. Top LED (Red): If ON, the Ethernet link has been established. Middle LED (Green): If ON, there is activity on the Ethernet link. Bottom LED (Yellow): Shows the speed of the Ethernet link. ON= 100 Mbps OFF= 10 Mbps. C Mounting Bracket Securing Points. D Safety Cable Securing Point. For information about safety cables, see the Installation Support Kit Instruction Sheet. E Power Over Ethernet (PoE) Port. Workflow Workflow Workflow Workflow for Setting up your Reader for Setting up your Reader for Setting up your Reader for Setting up your Reader For information about these tasks, see Page 2 of this document.

2 Setting up your AngleID™ Reader Setting up your AngleID™ Reader Setting up your AngleID™ Reader Setting up your AngleID™ Reader Test your Setup Test your Setup Test your Setup Test your Setup Configure Zones Configure Zones Configure Zones Configure Zones Connect your Devices Connect your Devices Connect your Devices Connect your Devices 1. Unzip the AngleID package onto your PC, and then run the AngleIDConfig.exe program to launch the Config Client. The Config Client has three tabs. All readers that you are licensed for are listed on the Readers tab. 2. On the Readers tab, assign an IP address and gateway for the reader. After the IP address is assigned successfully, the reader goes through a firmware download and boot process. This process can take a few minutes on first boot. After the reader has booted successfully, the status changes to reader is running. Run the Config Client Run the Config Client Run the Config Client Run the Config Client Define the detection zone, connected device, and tag(s) that you want to detect. The following procedure explains how set up a detection zone, using a single reader. 1. On the Recipes tab, click Create Recipe. A new blank recipe is added. 2. Specify the following details: • IP/Port details for the external control system for this recipe. • Full Tag ID, with colons, for example 00:11:CE:00:00:00:1B:DF. • Preferred protocol. 3. Click Update Recipe. The device and tag details on the recipe are updated. You can now tune your recipe. 4. Click Tune Recipe. This opens the Recipes config interface. 5. From the drop-down menu, select the MAC address of your reader. 6. Place the tag at the bounds of your detection zone. 7. Using your mouse, drag and adjust the horizontal and vertical bounds of the detection zone for the tag. You can now test your setup. 1. Move your tag into the horizontal and/or vertical bounds that you have configured. The Config tool shows that the tag is within the detection zone. 2. Move your tag outside the horizontal and/or vertical bounds. The Config tool shows that the tag is outside the detection zone. 3. To save your settings, click Finished Tuning. Mount your Reader Mount your Reader Mount your Reader Mount your Reader 1. Using suitable Ethernet cables, connect your devices. • Connect your reader to a PoE network switch. You can also use a separate PoE source and network switch if necessary. • Connect your Windows configuration PC to the same network switch. 2. Power on the PoE source and/or switch. 3. Note down the following details: • IP address and subnet of your PC. • MAC address of your reader. • ID of your tag. 1. Attach the mounting bracket to the back panel of your reader. 2. Fix the bracket to an appropriate surface. 3. Position your reader at a suitable angle, covering the detection zone where the tag must be tracked. Note that your reader has 90° vertical and 120° horizontal angular field of view. For more information about mounting, see the Installation Support Kit Instruction Sheet supplied with your mounting bracket. For further information or assistance, contact your Ubisense Support Representative or email us at: [email protected].