Electrolux EIDW5705PB Wiring Diagram

To replace dispenser: • shut off electricity to dishwasher, • remove outer door panel assembly, • disconnect wiring to the actuator, • remove the six screws, • remove the dispenser, • replace and reinstall screws, • rewire actuator. Check the Following 1. Fuse (blown or tripped). 2. 120 VAC supply wiring connection faulty. 3. Electronic control board defective. 4. No 12 VAC power to control. 5. Motor (inoperative). 6. Door switch (open contacts). 7. Door latch not making contact with door switch. 8. Touch pad circuit defective. 9. No indicator lamps illuminate when START or OPTIONS are pressed. 1. Motor (bad bearings). 2. Motor stuck due to prolonged non-use. 1. Improper voltage. 2. Motor windings shorted. 3. Glass or foreign items in pump. 1. Heater element (open). 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Hi-Limit thermostat defective. 1. Latch mechanism defective. 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Broken spring(s). 5. Defective actuator. 1. Drain restricted. 2. Electronic control board defective. 3. Defective drain pump. 4. Blocked impeller. 5. Open windings. 6. Wiring or terminal defective. 1. Water supply turned off. 2. Defective water inlet fill valve. 3. Check fill valve screen for obstructions. 4. Defective float switch. 5. Electronic control board defective. 6. Wiring or terminal defective. 7. Pressure Switch Stuck. 1. Drain hose (high) loop too low. 2. Drain line connected to a floor drain not vented. 1. Detergent allowed to stand too long in dispenser. 2. Dispenser wet when detergent was added. 3. Detergent cover held closed or blocked by large dishes. 4. Improper incoming water temperature to properly dissolve detergent. 5. See "Detergent cover will not open." Always disconnect the dishwasher from the electrical power source before adjusting or replacing components. Personal Injury Hazard Heater Refer to the cycle chart on the reverse side to determine when the heater is on during the wash cycle. The heater cycles ON and OFF for brief periods during the drying cycle. Voltage checks of the heater should be made in the dry portion of the service test mode. The drain hose must have a loop at a minimum height of 32 inches in order to insure proper drainage. Pump Assembly The pump assembly is driven by a synchronous motor. The motor drives a pump which supplies 100 percent filtered water Draining is accomplished by using a small separate synchronous drain pump mounted to the side of the sump. The drain pump is connected to the main pump by a small rubber hose. The drain check valve is located at the discharge end of the drain pump. The drain hose is attached by a clamp to the discharge end of the drain pump. Detergent and Rinse Aid Dispenser The detergent and rinse aid dispenser is a one piece component consisting of a molded detergent cup and a built-in rinse aid dispenser. The detergent cup has a spring loaded cover and the rinse aid dispenser has a removable cover. Liquid rinse aid is added to the dispenser up to the fill line indicator. The amount of rinse aid released can be adjusted by turning the arrow indicator from one, being the least amount, to four, being the greatest amount. Remedy 1. Replace fuse or reset breaker. 2. Repair or replace wire fasteners at dishwasher junction box. 3. Replace control board. 4. Replace control board. 5. Replace motor/impeller assembly. 6. Replace latch assembly. 7. Replace latch assembly. 8. Replace console assembly. 9. Replace console assembly. 1. Replace motor assembly. 2. Rotate motor impeller. 1. Check voltage. 2. Replace motor/impeller assembly. 3. Clean and clear blockage. 1. Replace heater element. 2. Replace control board. 3. Repair or replace. 4. Replace thermostat. 1. Replace dispenser. 2. Replace control board. 3. Repair or replace. 4. Replace dispenser. 5. Replace dispenser. 1. Clear restrictions. 2. Replace control board. 3. Replace pump. 4. Check for blockage, clear. 5. Replace pump assembly. 6. Repair or replace. 1. Turn water supply on. 2. Replace water inlet fill valve. 3. Disassemble and clean screen. 4. Repair or replace. 5. Replace control board. 6. Repair or replace. 7. Repair or replace. 1. Repair to proper 32-inch minimum height Symptom Dishwasher will not operate when turned on. Motor hums but will not start or run. Motor trips out on internal thermal overload protector. Dishwasher runs but will not heat. Detergent cover will not latch or open. Dishwasher will not pump out. Dishwasher will not fill with water. Dishwasher water siphons out. Detergent left in dispenser. Standard Dry Air Flow The heated, moist air leaving the dishwasher through the lower vent causes drier air to be drawn into the unit by way of intake vents located at the side of the tub. 020905 The water on the dishes is evaporated into drier air and the venting process continues. The heating element is turned ON and OFF during the entire drying cycle. Product Specifications Electrical Rating ...................................120 Volts, 60Hz Separate Circuit..15 amp min.- 20 amp max. Motor (Amps) ...................................... 1 amp Heater Wattage .......................... 475 - 630W Total Amps (load rated) ........................... 8.7 TempAssure .............................. 135°F ±5°F (60°C±3°C) [with outer door in place] TempBoost ................................ 140°F ±5°F Heated Wash/Heated Rinse Hi-Limit Thermostat ............... 200°F (93°C) Water Supply Suggested minimum incoming water temperature ............................ 120°F (49°C) Pressure (PSI) min./max. ................... 20/120 Connection (NPT) ..................................... 3/8" Consumption (Normal Cycle) ....................... ............................................ 5.8-6.0 U.S. gal Water valve flow rate (U.S. GPM) ........... 0.9 Water recirculation rate (U.S. GPM) .............. ................................................. approx. 5.28 Water fill time ..................................... 43 sec.

P/N EIDW5705 Electronic Series Color Code BK...................... Black BU........................ Blue PK.........................Pink RD..........................Red WH/RD.........White/Red RD-YE........Red/Yellow VT.......................Violet OR....................Orange GR......................Green W........................White Wiring Diagram Display Codes (LED) Display Codes (Readout) To start To delay start Press START/CANCEL pad. Close and latch door. Press DELAY START pad to select desired delay time. Close and latch door. To select a new cycle or option Press desired cycle and/or option pad. The indicator lights will change. Press START/CANCEL within 15 seconds to begin cycle. To cancel cycle Press START/CANCEL. Dishwasher will drain for 60 seconds, then shut off. For controls lock . . . . . . . . . . . Press and hold the AIR DRY pad for 3 seconds. To unlock, press and hold the AIR pad for 3 seconds. DRY CLEAN OPTION LED's Flashing ----------------- Shows completion of cycle. Indicator light will go off 30 seconds after door is opened. -- HI-TEMP WASH and AIR DRY/ LED's flashing indicates power failure has occurred. Press START/CANCEL pad and reselect desired options and cycle. LOW RINSE SANITIZE ----------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is filled. --------------- The SANITIZED criteria has been met. Indicator light will go off 30 seconds after door is opened. This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products North America cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this Service Data Sheet. Operation LO. PF Cd '01-24' .........Low liquid in the rinse aid dispenser ..........A power failure has occurred ..........Close the door ....Hour(s) delay before start The water/service test is a Special function initiated from the power failure mode or idle mode. While in power failure or idle mode - simultaneously press the AIR DRY and START/CANCEL pads for 1 1/2 seconds. The dishwasher will then step through the test cycle per the chart. Pushing the START/CANCEL pad will advance the dishwasher to the next step. Water/Service Test (Some models) Cycle Selection Options