Vivotek FD8151V Quick Installation Manual

If the Network Camera becomes wet, power off immediately. Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera in high humidity environments. Warning Before Installation Do not insert sharp or tiny objects into the Network Camera. Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. 5 0 0 02 47 0 1 G Screws FD8151V Quick Installation Guide / Warranty Card Software CD Package Contents 1 NOTE: All cables are user-supplied. Use a CAT5 standard UTP or better quality cable. In order to pass the Ethernet cable through the routing path, the maximum cable diameter al- lowed is 5.2mm. Focus Adjustment Tool Anti-tamper Screwdriver Alignment Sticker

Outer View Physical Description 2 Leave the slide cover in place if you route cables through the bottom and then through a hole on the ceiling or wall. DI+ DI- Max. is 40V. Slide cover Digital input Lens Tilt retention screw Reset button Screw slot Inner View RJ-45 Socket Side View MicroSD/SDHC card slot Internal microphone IR LEDs

E li h Hardware Installation 3 Removing the Dome Cover 1. Unscrew the anit-tamper screws using the included screwdriver. 2. Remove the dome cover. 3. Remove the slide cover if you want to route cables from the side of camera instead of a hole on the ceiling or wall. 0002D10766AD FD8151V-F2 1. Record the MAC address before installing the camera. IMPORTANT: 1. It is recommended to use an Ethernet cable that comes without the strain relief boot. You can remove the boot if your cable comes with one. Strain relief boot NOTE: 

Mounting the Network Camera - Ceiling or Wall Mount 1. Use the alignment sticker as a template to mark where holes will be drilled on the ceiling. Drill two holes into the ceiling; and hammer in the plastic anchors. 2. Drill another hole if you want to route cables through the ceiling or wall. 3. Connect and route an Ethernet cable through the ceililng or wall. 4. Temporarily attach the Network Camera to the ceiling using two included screws. 2 3 1 4 NOTE: 1. Do not completely tighten the mounting screws in the screw slots yet. You may need to turn the camera left or right for a best shooting direction later. 2. The camera can only be powered by PoE. There is no DC or AC input connector. Routing hole position 5. After tuning the camera's shooting direction and tilt angle, you can remove the camera and drill another 2 holes to the ceiling for better support. For vandal-proof applications, you can secure the camera using all 4 mounting holes.

E li h Network Deployment 4 Power over Ethernet (PoE) POWER COLLISION LINK RECEIVE PARTITION 1 2 3 4 5 PoE Switch When using a PoE-enabled switch This Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch via Ethernet cable. When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch. POWER COLLISION LINK RECEIVE PARTITION 1 2 3 4 5 PoE Power Injector (optional) Non-PoE Switch

Assigning an IP Address 5 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up. Double-click on the MAC address that matches the one printed on the camera label or the S/N number on the package box label to open a browser management session with the Network Camera. For further setup, please refer to the user's manual on the software CD. Ready to Use 6 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents.

E li h 1 2 1. There is a tilt retention screw near the lens module. Use a #0, #1, or #2 Phillips screwdriver to loosen the screw. Use the lens adjustment tool to carefully change the tilt angle. 3. Tighten the tilt retention screw and the camera's mounting screws after you change the horizontal shooting direction. If you have concerns for vandalism, remove the camera and drill 2 more mounting holes for better support as previously mentioned. 25° 25° 60° Adjusting the Lens 7 2. You may also tune the camera's horizontal orientation by turning it along its curved screw slots. For the F2 lens: the max. tilt angle is 45°. For other lens: the max. tilt angle is 60°. IMPORTANT:

5. Use a piece of clean cotton cloth to hold and install the dome cover. 6. Install dome cover by fastening the 3 anti-tamper screws. 4. With a live video feed, you can place the included focus adjustment tool carefully on the lens, and use it to turn the lens clockwise or counter-clockwise to adjust to the best image focus. You may try tuning the focus slightly closer due to the concern that focus might be changed when the dome cover is installed.