Windsor ADM8IA Operator Instructions Manual

Lire ce manuel avant d’utiliser la machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen MODEL: COUNTRY ADM8IA - 10080010 AUSTRALIA ADM8IB - 10080020 BRITIAN ADM8IE - 10080030 EUROPE ADM8IS - 10080040 SWITZERLAND Operating Instructions (GB/USA) Manuel d’utilisation (FRE) Bedienungsanleitung (GER) 86038270 04/26/11 PRV NO. 98655 AL CARPET EXTRACTOR IPX4

ADMIRAL 86038270 04/26/11 1 Data Log/Table of Contents .............. 1 Safety Instructions ............................ 2 Controls ............................................ 3-5 Operations ........................................ 6-11 Troubleshooting ................................ 12 Blank Page ....................................... 13 Wiring Diagram ................................. 14 Maintenance ..................................... 15-17 Technical Specifications ................... 18 Parts Lists ......................................... 19-34 Spare Parts/Notes ............................ 35 EC Declaration of Conformity ........... 36 INSPECTION Carefully unpack and inspect your machine for shipping damage. Each unit is operated and thoroughly inspected before shipping, and any damage is the responsibility of the carrier, who should be notified immediately. Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product. To register your product go to: www.windsorind.com/WarrantyRegistration.aspx For customer assistance: 1-800-444-7654

2 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet. Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service. Use only indoors. Do not use outdoors or expose to rain. Do not allow machine to be used as a toy. Close attention is necessary when used by or near children. Use only as described in this manual. Use only manufacturer’s recommended components and attachments. Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center. Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run machine over cord. Keep cord away from heated surfaces. Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord. Do not handle the electrical plug or machine with wet hands. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is intended for cleaning carpet only. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. This machine is not suitable for picking up health endangering dust. Turn off all controls before unplugging. Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors. This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. SAVE THESE INSTRUCTIONS ! WARNING:

3 1. Main Handle. Used to pull and maneuver machine. 2. Handle Adjustment. Used to adjust height of handle. 3. Electrical Cord. 4. Solution Switch. Turns on pump. Continuous position (bottom) activates electro-valve to dispense solution to floor through jets. Intermittent position (up) requires operator to depress 1 of 3 trigger switches to dispense solution. Center position is off. 5. Brush Motor Switch. Turns on brush motor. 6. Vacuum Motor Switch. Turns on vacuum motor. 7. Trigger Switches. Activates electro-valve to dispense solution to floor through jets when solution switch is in the intermittent position. 8. Brush Motor Circuit Breaker. 4 amp. Breaker protecting brush motor. 9. Vacuum Motor Circuit Breaker. 7 amp. Breaker protecting vacuum motor. 10. Recovery Dump Hose. Facilitates draining dirty cleaning solution. 11. Solution Dump Hose. Facilitates draining excess cleaning solution from solution tank. 3 1 10 11 2 5 8 9 4 6 7

4 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning tools. 2. Vacuum Hose Door. Used to connect various auxiliary 1 ½ inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from storage position to various carpet heights. 4. Recovery Tank. Used to collect dirty cleaning solution. 5. Solution Tank. Used to hold cleaning solution. 6. Recovery Tank Dome. 7. Vacuum Shoe. 8. Brush Housing. 9. Front Lifting Handle. 10. Cleaning Solution Filter. 11. Solution Tank Fill Hose. 4 5 6 7 8 3 2 1 10 9 11

5 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 2 1 3 4 5 6 6

6 FILLING THE ADMIRAL NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank. Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank. CHEMICALS Suitable Chemicals Non-Compatible Chemicals Alkalis Aldehydes Detergents Aromatic Hydrocarbons Hydroxides SP Butyls Soaps Carbon Tetrachloride Vinegar Clorox* Chlorinated Bleaches Chlorinated Hydrocarbons Lysol* Methyl Ethel Ketone (MEK) Perchorethylene (perc) Phenolics Trichlorethylene D-Limonene * Product Trademark Names STEP 1 STEP 2 STEP 3 STEP 4 RECOVERY TANK SOLUTION TANK Remove recovery tank FILL LINE Replace recovery tank Add cleaning chemical 8 – 16oz. (237ml – 473ml) Add water 8 gal. (30.3 ltr.) 140°F (60°C) or

7 Remove electrical cord and literature from recovery tank. Fill solution tank (see filling instructions page 6). Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to prevent damage to motor or carpet. Plug cord into grounded outlet. Note: Be sure dome is seated on recovery tank, and float shut-off is installed correctly. Turn on brush and vacuum motor switches (“ON”=“I”). Turn on solution switch for continuous spray or set switch to intermittent to allow use of trigger switches. STEP 1 STEP 2 STEP 3 STEP 4 CORRECT INCORRECT 1/8in (3mm) SOLUTION VACUUM CONT INT BRUSH ON ON

8 Select continuous setting to start solution spray or select intermittent setting to enable use of trigger switches to start solution spray. The intermittent setting requires the operator to hold any one of the three trigger switches in the “on” position with the fingers, and is typically used in small areas where short cleaning passes are made. The continuous setting allows the operator to set the switch in the “on” position with one touch, and is typically used in large areas where long cleaning passes are made. Lower machine to floor. Adjust handle to comfortable operating position. Tip machine back by main handle to move to starting point. STEP 5 STEP 6 STEP 7 INT CONT

9 Release intermittent trigger switches or turn off continuous setting on solution switch approximately 1 foot before ending cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area a minimum of 1inch on the right (close cleaning) side of machine. During operation, observe the following: The Admiral is equipped with clear internal covers to facilitate operator viewing of dirty solution and vacuum air flow. During operation, observe the vacuum intake cover. Large amounts of water or foam entering the vacuum system can damage the vacuum motor. If you notice either condition, shut down the machine immediately. Empty recovery tank and/or add defoamer to recovery tank. STEP 2 STEP 3 STEP 4 Start at wall closest to power outlet. Pull straight back without pushing down on handle. STEP 1 SOLUTION INTAKE COVER VACUUM INTAKE COVER 1in. (25mm) OFF 1ft. (30cm)

10 To speed drying, use a Windblower™ fan. Empty recovery tank by releasing dump hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. STEP 7 STEP 8 After cleaning, turn off all controls, return brush to storage position and carefully unplug machine. STEP 6 STEP 5 Use right side of machine for cleaning against walls. RECOVERY DRAIN SOLUTION DRAIN OFF OFF OFF

ADMIRAL 86038270 05/22/07 11 Turn on vacuum motor switch and set solution switch to intermittent position. Note: Be sure brush switch is in off position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning. STEP 3 STEP 4 STEP 1 STEP 2 Use only one of the following acceptable accessory tools. 86000020 – PRV NO. HT 86000000 – PRV NO. DDH 86041150 – PRV NO. DH 86031540 – PRV NO. 39504 86000610 – PRV NO. 89227 86000600 – PRV NO. 89226 Pull back collar and insert over machine mounted fitting, then release collar to lock into place. Lift door on front of vacuum shoe and insert 1 ½ inch hose cuff into hole. SOLUTION VACUUM ON OFF INT BRUSH

12 PROBLEM CAUSE SOLUTION No Power, Nothing Runs 1. Is the cord plugged in. 2. Circuit breaker tripped in building. 3. Faulty switch. 4. Faulty power cord or pigtail. 1. Plug in cord. 2. Reset breaker 3. Call for service. 4. Call for service. Vacuum Motor Will Not Run 1.Vacuum circuit breaker tripped. 2.Faulty main vacuum switch. 3.Loose wiring. 4.Faulty vac motor. 1.Reset breaker 2.Call for service. 3.Call for service. 4.Call for service. Vacuum Motor Runs But Suction Is Poor 1.Debris lodged in vac shoe. 2.Dome gasket defective or missing. 3.Vacuum hose cracked or hose cuff loose. 4.Recovery tank full / float ball stuck in the up position. 1.Remove debris from vac shoe. 2.Replace as necessary. 3.Replace or repair as necessary. 4.Turn off vac motor. Drain and rinse recovery tank. Poor Or No Water Flow (Carpet Is Streaky) 1.Main pump switch off. 2.Jets clogged or missing. 3.Solution filter clogged. 4.Faulty solenoid. 1. Turn on. 2.Clean using a vinegar /water solution or replace. 3.Drain solution tank and clean solution filter. 4.Call for service. Brush Does Not Spin 1.Brush switch off. 2.Brush circuit breaker tripped 3.Brush belt broken. 4.Faulty brush motor. 1.Turn on brush switch. 2.Reset circuit breaker. 3.Replace as necessary. 4.Call for service.

14 86268290 PRV NO. 88229 86268460 PRV NO. 88333 86268430 PRV NO. 88323 86268370 PRV NO. 88276 FILTER 86003650 PRV NO. 34362 86268430 PRV NO. 88323 86268430 - PRV NO. 88323 86238840 PRV NO. 41356 86238830 PRV NO. 41355 86268900 PRV NO. 88655 86266720 PRV NO. 880043 86268420 PRV NO. 88317 86001240 PRV NO. 14020 86268750 PRV NO. 88567 86238820 PRV NO. 41351

15 PERIODIC MAINTENANCE Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow-dry. NOTE: Do not use pins, wire, etc. to clean nozzles as this could destroy spray pattern. Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. If the cable insulation is broken or frayed, repair or replace it immediately. Don’t take chances with electrical fire or shock. DAILY / REGULAR MAINTENANCE Before making any adjustments or repairs to the machine, disconnect the power cord from electrical source. 1. Empty unused cleaning solution from the solution tank. 2. Inspect and clean filter screen in solution tank. 3. Flush pumping system with 4 or 7 liters of clean, hot water. 4. After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a 1-10 bleach to water solution. Waste water should be disposed of properly. 5. Check for and remove any lint or debris around vac shoe. 6. Check spray jets for full spray pattern. 7. Remove lint and dirt build-up from brush and housing. NOTE: Brush removal. A. To remove brush, grab and pull brush out from end opposite drive belt (operator’s right). Remove other end from brush driver. B. To install brush, line up slots in brush core with pin in driver on drive belt side (operator’s left) and push brush onto driver. Then snap bearing end (opposite end) of brush into retaining clip. 8. Check cooling air screen (located on frame behind left wheel) for lint or debris. 9. Check float and shut-off screen and clean as necessary. NOTE: Always store machine with brush in “Store” position.

16 ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Locate the vacuum motor wires and disconnect at the connector. Close the solution tank. 5. Remove the (6) screws holding the vacuum motor cover (p/n 86003080 – PRV NO. 27809) to the solution tank. 6. Remove the vacuum motor. 7. Reverse process to install vacuum motor. WARNING: The green ground wire must be attached for safe operation. See wiring diagram. Note: When replacing carbon vac motor brushes loosen wire terminal BEFORE removing screws on bracket. Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely. If armature commutator is not concentric, extremely pitted, or grooved the motor will need to be replaced or sent to a qualified service center to restore vac performance. Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" long. Note: Place stop in groove. End Cap Carbon Brushes Vac Motor Carbon Brushes Replacement (Ametek) Wire Terminal Wire Terminal Vacuum Motor Carbon Brushes Replacement (Windsor) WARNING: The green ground wire must be attached for safe operation. See wiring diagram. End Cap Carbon Brushes If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely. Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long. 3 8 [9.5mm]

17 ! WARNING: SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug the machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Remove solution hoses from fittings in pump. 5. Remove the (2) screws that fasten the pump to the frame. 6. Reverse process to install pump. ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. BELT REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank and brush. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Loosen the (4) screws that hold the brush motor in place and slide motor forward to release tension in belt. 5. Remove the (2) screws that fasten the vacuum shoe links (p/n 86227350 – PRV NO. 05016) to the brush housing. 6. Remove the (3) screws that fasten the side plate (p/n 86249420 – PRV NO. 62759) to the brush housing to remove belt. NOTE: All components associated with driving the brush will come out with the side plate. 7. Reverse process to install belt. 86249420 PRV NO. 62759 86227350 PRV NO. 05016 Pressure Switch 86161980 PRV NO. 42-809332 Valve Asm 86258830 PRV NO. 84161 Diaphragm 86003400 PRV NO. 29206 Pump Replacement Parts for Shurflo 100 psi (86026400 – PRV NO. 65254) PumpHead 86251040 PRV NO. 65187 Motor 86247370 - PRV NO. 53246 Diaphragm 86235120 PRV NO. 29219 Pump Head 86251090 PRV NO. 65204 Valve Asm 86258860 PRV NO. 84166 Pump Replacement Parts for Flojet 100 PSI 230V (86004770 – PRV NO. 47477)

18 POWER TYPE ELECTRICAL: 230-240 V, 7 A, 50 HZ ELECTRIC VACUUM MOTOR: (1) –3 stage, 1 hp, 99 cfm (2.80 cubic meters/min.) Waterlift – 117” (297cm) BRUSH: (1) 15” (38.1 cm.) SOLUTION PUMP: 100 PSI, diaphragm style, internal bypass SOLUTION CAPACITY: 8 gallons (30.3 ltr) RECOVERY CAPACITY: 8 gallons (30.3 ltr) BRUSH SPEED: 1000 rpm GENERAL DIMENSIONS/WEIGHT Vacuum shoe: 17” (43.18 cm) cast aluminum with spring loaded down pressure WHEELS: (2) 10” dia. (25 cm) wheels by 2” WEIGHT: 92 lbs. (42 kg) LENGTH: 35” (89 cm) HEIGHT: 42” (107 cm) WIDTH: 18.5” (47 cm) SOLUTION SPRAY: 2 quick change jets. POWER CABLE: 50’ (12.7 m) (1 mm) 18.5” (47cm) 35” (89cm) 42” (107cm)

19 2 16 27 29 20 8 5 22 11 10 15 7 13 14 24 25 4 (SEE PG. 29) 3 26 34 21 18 19 A 12 33 9 6 B 30 31 (SEE PG. 27) C

20 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 - OPEN - - 2 86003620 34341 1 FRAME, CLP FAMILY 3 86004340 39528 1 HOSE ASM, 1.5 BLK VAC X 15.5 4 86001660 41236 2 HUBCAP, 5/8" SHAFT 5 86238820 41351 1 HARNESS, MAIN, CLP/ADM 6 86239610 41354 1 HINGE, TANK TO FRAME 7 86005370 53641 1 MOTOR ASM, BRUSH 230V 8 86005640 57030 2 NUT, 10-32 HEX NYLOCK 9 86005810 57245 3 NUT, 1/4-20 HEX NYLOCK SS 10 86198530 99809 2 FOAM TAPE, 1/8 THK X 3/4 1SDA 11 86249430 62761 1 PLATE, BRUSH MTR CLAMP 1000045872 12 86006020 64099 1 PULLEY, 1.4 OD, 6GR, MICRO-V 13 86250130 66282 6 PLUG, HOLE, .375" BLK 14 86250140 66288 2 PLUG, 9/16 OD BLK NYLON 15 86276410 70643 2 SCR, 1/4-20 X 3/8PPHMS 1000045872 16 86273980 70066 2 SCR, 10-32 X 3/4 PPHMS 17 - OPEN - - 18 86010630 87013 2 WASHER, 1/4 ID X 5/8 OD SS 19 86010660 87025 2 WASHER, 1/4 LOCK EXT STAR SS 20 86010650 87018 2 WASHER, #10 X 9/16 OD 21 86006550 70074 2 SET SCR, 10-32 X 1/4 KCP 22 86256190 73197 1 STRAIN RELIEF, 90 DEGREE 23 - OPEN - - 24 86259960 89506 2 WHEEL, 1-15/16 X 10” HOOSIER 25 86066230 03107 1 AXLE, 5/8 X 17.06L 26 86134490 99667 10” HEAT SHRINK, 3/4 ID UL/CSA 27 86253090 73943 1 SEAL, FRAME/TANK 28 86002370 20035 1 CLAMP, 7/16 DIA NYLON UL 29 86233140 20041 1 CLAMP, 2.0" WORM GEAR 30 86274760 70271 2 SCR, 1/4-20 X 1/2 HHCS PLTD 31 86006530 70057 2 SCR, 1/4-20 X 1 PPHMS SS 32 86272160 66052 1 PIN, ROLL 1/8” X 1.0”L 33 86276610 70697 1 SCR, ¼-20 X 1.25 PPHMS SS 34 86005710 57105 3 NUT, ¼-20 HEX W/ STAR WASHER

21 25 9 3 2 46 5 31 25 29 30 18 38 39 16 30 34 17 20 37 26 24 11 8 15 3 26 19 6 21 35 28 29 25 17 32 23 14 30 22 4 27 1 16 7 10 12 13 25 40 41 42 43 33 45 36 44 47

22 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86000730 03110 1 AXLE, ROLLER 2 86227100 04084 1 ADAPTER, BRUSH BRG. 3 86000900 09019 2 BEARING, 1.125ODX.500IDX.375 4 86001100 11045 1 BELT, 180J6 MICRO-V 5 86001140 12514 1 BRUSH, 15L X 3.38OD 6 86001300 140343 1 BRKT, BRUSH PULLEY 7 86001310 140351 1 BRKT, BRUSH HEIGHT 8 86003620 34341 REF FRAME, CLP FAMILY 9 86004060 36192 2 GUARD, THREAD 10 86004470 41345 1 HOUSING, BRUSH 15" 11 86004980 50998 1 LABEL, BRUSH HEIGHT 12 86093080 51311 1 LINKAGE, ASM, BRUSH HEIGHT 13 86005110 51312 1 LINKAGE ASM, ROLLER SUPPORT 14 86005120 51314 2 LINK, ROLLER, FRONT 15 86005130 51317 1 LEVER, HEIGHT ADJUSTMENT 16 86005640 57030 4 NUT, 10-32 HEX NYLOCK 17 86005850 57271 2 NUT, 3/8 DIA CAP, TYPE PUSH PLT 18 86249410 62758 1 PLATE, BRUSH HOUSING RH 19 86249420 62759 1 PLATE, BRUSH HOUSING LH 20 86005930 62762 2 PLATE, AXLE RETAINER 21 86250680 64098 1 PULLEY, 2.2 OD, 6GR, MICRO-V 22 86006220 66192 1 PIN, ROLL 1/4 X 1.25L 23 86006430 67411 1 ROLLER, 1.9 DIA X 10.5 LG 24 86006510 70043 2 SCR, 10-32 X 5/8 PFHMS 25 86006590 70088 8 SCR, 10-32 X 1/2 PPHMS SS DL 26 86006650 70177 7 SCR, 10-32 X 1/2 FHMS SS 27 86006700 70232 2 SCR, 10-32 X 3/8 FHMS SS 28 86275530 70497 2 SCR, #10-24 X 1/2 SHCS 29 86010640 87016 4 WASHER, #10 LOCK EXT STAR SS 30 86010650 87018 6 WASHER, #10 X 9/16 OD 31 86007030 70675 4 SCR, 1/4-20 X.5/8 THMS PLTD NP 32 86230620 12524 1 BRUSH 15 L X 3.38 OD G2 1000060649 33 86251710 67467 1 RING, TOLERANCE 7/8 ID X 1/2 W 1000060649 34 86003070 27805 1 CLIP, BEARING 35 86003370 29157 1 DRIVER, BRUSH 36 86278130 70737 1 SHLDR BOLT, 3/8 OD X 3/8 L SS NP 1000060649 37 86272770 67094 1 RING, 1/2 EXT. SNAP 38 86272510 66310 2 PIN, CLEVIS 1/4 X 1/2 PLTD 39 86008650 80604 2 COTTER, 1/4" RING 40 86342240 - 1 SPACER, .81 X 1.06 X.125 41 86006030 64102 1 PULLEY ASM, BRUSH 42 86003390 29208 1 DRIVER ASM, BRUSH 43 86001140 12514 1 BRUSH ASM, 15 IN 44 86227150 05158 1 ADAPTER, BRUSH BRG DIE CAST 1000060649 45 86228890 09137 2 BEARING, R6 3/8 ID 1000060649 46 86028010 47383 1 BRUSH BEARING ASM 47 86004750 47416 REF KIT, BRNG/ADPTR EXTRCTR

23 3 20 13 10 16 6 5 11 15 19 18 1 20 7 16 8 21 17 9 2 12 22 26 26 D 27 28 29 29 (SEE SOLUTION TANK) 22 4 25 25 23 24

24 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86002470 22072 1 COUPLING, 1/4 ANCHOR W/1" HEX 2 86002480 22090 2 CONNECTOR, 1/8FPT X 1/4 TUBE QC 3 86003470 31072 1 ELBOW, SWIVEL, 1/4MPTX1/4TUBE 4 86003490 31074 1 ELBOW, SWIVEL,3/8MPTX3/8TUBE QC 5 86004570 44067 2 JET BODY, MINI PROMAX BODY 6 86241680 44073 2 JET, MINI PROMAX 9503 7 86005640 57030 2 NUT, 10-32 HEX NYLOCK 8 86026400 65254 1 PUMP ASM, 230V 100PSI W/CONN 9 86250140 66288 2 PLUG, 9/16 OD BLK NYLON 10 86274410 70195 2 SCR, 10-32 X 1.25 PPHMS 11 86273750 70011 2 SCR, 1/4-20 X 5/8 HHCS SS 12 86003640 34355 1 FITTING,1/4 TUBE,"Y", QC 13 86008360 78419 1 TEE, 3/8 MPT X 3/8 TUBE, QC 14 86010570 84165 1 VALVE ASM,SOLENOID CLP FAMILY 15 86010810 87191 2 WASHER, 1/4"IDX1.0OD. FLAT SS 16 86010650 87018 4 WASHER, #10 X 9/16 OD 17 86010820 87192 2 WASHER, 7/16 X 3/4 X .19RUBBER 18 86005590 56014 1 NIPPLE, 1/4 CLOSE 19 86005580 56012 1 NIPPLE, 1/4 FPT QD 20 86003500 31076 2 ELBOW, 1/4 MPT X 3/8 TUBE, QC 21 86006590 70088 2 SCR, 10-32 X 1/2 PPHMS SS 22 86279930 29277 2 DUCT, 1/2 ID SPLT FLX X 16” 23 86267400 880278 1 WIRE, 22" GRN/18 76011 X 76011 24 86282340 39720 1 HOSE, 3/8 OD X 1/4 ID URTHN X 22” 25 86282350 39721 2 HOSE, 3/8 ID NYLON YLW X 17” 26 86281900 39531 3 HOSE, 1/4 ID NYLON YLW X 5” 27 86253020 73963 1 SCREEN, INTAKE 28 86197400 31022 1 ELBOW, 1/8NPT STREET 29 86227950 140387 2 BANDS, RUBBER

25 PRIOR TO S/N 1000153482 3 4 13 10 16 6 5 11 15 19 18 1 20 7 16 8 21 17 9 2 14 12 25 26 23 28 24 26 D 20 (SEE PG. 29) 27 (SEE SOLUTION TANK)

26 PRIOR TO S/N 10000153482 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86002470 22072 1 COUPLING, 1/4 ANCHOR W/1" HEX 2 86002480 22090 2 CONNECTOR, 1/8FPT X 1/4 TUBEQC 3 86003470 31072 1 ELBOW, SWIVEL, 1/4MPTX1/4TUBE 4 86003490 31074 1 ELBOW, SWIVEL,3/8MPTX3/8TUBEQC 5 86004570 44067 2 JET BODY, MINI PROMAX BODY 6 86241680 44073 2 JET, MINI PROMAX 9503 100003082 7 86005640 57030 2 NUT, 10-32 HEX NYLOCK 8 86004770 47477 1 Kit, 230V FLOJET PUMP REPLMNT 9 86250140 66288 2 PLUG, 9/16 OD BLK NYLON 10 86006830 70386 2 SCR, 10-32 X 1.0 PPHMS 11 86273750 70011 2 SCR, 1/4-20 X 5/8 HHCS SS 12 86003640 34355 1 FITTING,1/4 TUBE,"Y", QC 13 86008360 78419 1 TEE, 3/8 MPT X 3/8 TUBE, QC 14 86010570 84165 1 VALVE ASM,SOLENOID 230V 15 86010810 87191 2 WASHER, 1/4"IDX1.0OD. FLAT SS 16 86010650 87018 4 WASHER, #10 X 9/16 OD 17 86010820 87192 2 WASHER, 7/16 X 3/4 X .19RUBBER 18 86005590 56014 1 NIPPLE, 1/4 CLOSE 19 86005580 56012 1 NIPPLE, 1/4 FPT QD 20 86003500 31076 2 ELBOW, 1/4 MPT X 3/8 TUBE, QC 21 86006590 70088 2 SCR, 10-32 X 1/2 PPHMS SS 22 - OPEN - - 23 86267400 880278 1 WIRE, 22" GRN/18 76011 X 76011 1000045872 24 86281890 39529 1 HOSE, 3/8 URETHANE X 29" 25 86004350 39530 1 HOSE, 3/8 NYLON X 6" 26 86281900 39531 3 HOSE, 1/4 ID NYLON X 6" 27 86253020 73963 1 SCREEN, INTAKE 28 86285760 39551 1 HOSE, 3/8 NYLON X 29”

ADMIRAL 86038270 05/22/07 28 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86227350 05016 4 ARM, VAC SHOE PARALLEL 2 86234760 27674 1 COVER, ACCESSORY PORT 3 86005810 57245 4 NUT, 1/4-20 HEX NYLOCK SS 4 86006790 70351 2 SCR, 10-32 X 3/8 HHTR W/STAR 5 86275120 70360 4 SCR, 1/4-20 X.75 PPHMS PHIL 6 86006840 70390 4 SCR, 1/4-20 X 1 FHCS PLTD 7 86008130 73958 8 SPACER, 3/8ODX.058WX.2814,CRS 8 86010620 85039 1 VAC SHOE, 15" 9 - OPEN - - 10 86010630 87013 4 WASHER, 1/4 ID X 5/8 OD SS 11 86010700 87074 8 WASHER, WAVE 3/8ID X3/4D X.125 12 86003780 35171 1 GASKET, ACCESSORY PORT 13 86008120 73955 2 SPRING, EXT .38D X2.75L X.055W

ADMIRAL 86038270 05/22/07 29 13 17 6 12 4 10 15 5 14 16 20 7 1 19 18 11 8 3 9 2 33 32 31 30 29 28 27 26 25 24 23 22 21 35 34 C SEE FRAME 38 37 39 41 29 40 42 43 44 45 46 36A, 36B 36C, 36D 47

ADMIRAL 86038270 05/22/07 30 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86001240 14020 1 TERMINAL BLOCK, 115V (3-4-3) 2 86230110 14312 1 BREAKER, 7A 250VAC 50VDC 3 86002020 14949 1 BREAKER, 4A CIRCUIT 4 86002010 14942 2 BOOT, 3/8 CIRCUIT BREAKER 5 86233240 20084 2 CLAMP, HANDLE LOCK 6 86261000 23671 1 CORD ASM 7 86003130 27823 3 CONTACT, ELECTRICAL, FLAT 8 86003140 27824 3 CONTACT, ELECTRICAL, BENT 9 86076550 38283 2 HANDLE, ADM8 10 86004100 38286 1 HANDLE, CONTROL PANEL FRONT 11 86004110 38287 1 HANDLE, CONTROL PANEL REAR 12 86004790 48012 1 KNOB, 5/16-18 4 PRONG 13 86246300 51039 1 LEVER, HANDLE CLAMP 14 86246650 51313 2 LINK, HANDLE ADJ. 15 86005670 57040 2 NUT, 1/2 NPT CONDUIT 16 86081530 62766 1 PLATE, CONTROL PANEL, CLP/ADM 17 86264270 67073 1 ROD, HANDLE LOCK 18 86007140 72130 2 SWITCH, SPST 2-POSITION ROCKER 19 86087410 73180 1 SPACER, .50 ODX.058WX9.84L CRS 20 86256240 73505 1 STRAIN RELIEF, 1/2 NPT TRUMPET 21 86008350 78418 3 TRIGGER, SWITCH 22 86245950 50996 1 LABEL, CONTROL PANEL, CLP/ADM 23 86005760 57116 2 NUT, 6-32 W/STAR WASHER PLTD 24 86005810 57245 4 NUT, 1/4-20 HEX NYLOCK SS 25 86272190 66068 1 PIN, ROLL 1/8" X 5/8"L 26 86227650 03109 1 AXLE, HANDLE ADM8 27 86006870 70406 9 SCR, #10 X 3/4 PPHST TYPE B 28 86006620 70127 6 SCR, 6-32 X 1/4 PPHMS SS 29 86006790 70351 5 SCR, 10-32 X 3/8 HHTR W/STAR 30 86274150 70105 4 SCR, 1/4-20 X 1.75 HHCS 31 86006710 70235 2 SCR, 6-32 X 1.0 PH BLK NYLON 32 86005750 57113 2 NUT, 5/16-18 HEX NYLOCK 33 86010750 87100 2 WASHER, 3/8 ID INT.LOCK THIN 34 86198480 27371 2 CLIP, POWER CORD 35 86238820 41351 REF HARNESS, MAIN CLP/ADM 36A 86002610 23683 1 CORD ASM, 230V BRITIAN 50FT 36B 86002600 23682 1 CORD ASM, 230V EURO 50FT 36C 86031550 23681 1 CORD ASM, 230V SWISS 50FT 36D 86260960 23521 1 CORD ASM, 230V AUST 50 FT 37 86272840 67147 1 RING, 2" DIA SPLIT 38 86256170 73169 1 STRAIN RELIEF, CORD HOOK 39 86007200 72162 1 SWITCH, DPDT3-POSITION ROCKER 40 86006830 70386 1 SCR, 10-32 X 1” PPHMS 41 86005700 57104 3 NUT, 10-32 W/STAR WASHER PLTD 42 86010660 87025 1 WASHER, 1/4 LOCK EXT STAR SS 43 86010670 87029 2 WASHER, 5/16 FLAT SS 44 86002870 27417 1 CORD, 99807 1/8 X 12" 45 86232290 500017 1 CARD, INSTRUCTION ADM8 46 86007130 72128 1 SWITCH, DPDT, 2 POSITION ROCKER 47 86245040 50279 1 LABEL, GROUND SYMBOL

ADMIRAL 86038270 05/22/07 31 6 14* 27 16 5* 4 2 8 24* 17* 11 15 20 12 7 3 13 16 10 1 9 19 18 A B D 7* 22* 21* 23* 18 26 25 28 16 27 29 30 31 32 (SEE FRAME) (SEE FRAME) (SEE PUMP)

ADMIRAL 86038270 05/22/07 32 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86233140 20041 2 CLAMP, 2.0" WORM GEAR 2 86233150 20042 1 CLAMP, 3/8 HOSE (D-SLOT) 3 86003080 27809 1 COVER, VAC MOTOR 4 86003090 27810 1 COVER, BELT 5 86235500 31081 1 ELBOW, 3/8 MPT X 3/8 TUBE, PLASTIC 6 86003790 35175 2 GASKET, TANK TO VAC COVER 7 86003920 35231 2 GASKET, VAC COVER (CLP FAMILY) 8 86281880 39526 1 HOSE,1/2 CLEAR X 12 9 86240090 39527 1 HOSE, 1.5 BLK VAC X 3.0 10 86004340 39528 REF HOSE ASM, 1.5 BLK VAC X 15.5 11 86240980 41348 1 HOUSING, VAC MOTOR 12 86005420 53791 1 VAC MOTOR ASM, CLP FAMILY 13 86275690 70525 6 SCR, #10 X 1.0 PPHST TYPE B 14 86032260 75259 1 TANK, ADM SOLUTION 15 86259060 85037 1 VENT, COOLING AIR SMALL 16 86010650 87018 10 WASHER, #10 X 9/16 OD 17 86007970 73864 1 STRAINER, 3/8 IN. NPT 60 MESH 18 86010630 87013 5 WASHER, 1/4 ID X 5/8 OD SS 19 86006580 70085 3 SCR, 1/4-20 X 1/2 PPHMS SS DL 20 86233260 20092 1 CLAMP, 3.5" WORM GEAR 21 86003950 35236 1 GASKET, TANK, L-F 22 86003960 35237 1 GASKET, TANK, L-R 23 86003970 35238 1 GASKET, TANK, RH 24 86197940 40027 1 HOSEBARB, 3/8MPTX1/2 90D DL 25 86275120 70360 2 SCR, 1/4-20 X.75 PPHMS PHIL 26 86010660 87025 2 WASHER, 1/4 LOCK EXT STAR SS 27 86006600 70114 4 SCR, #10 X 3/4 PPHST TYPE B 28 86095840 89183 1 WELDMENT, HANDLE PIVOT ADM8 29 86005810 57245 2 NUT, 1/4-20 HEX NYLOCK SS 30 86260690 02130 1 HOSE ASSY- FILL HOSE 31 86233150 20042 1 CLAMP, 3/8 HOSE (D-SLOT) 32 86197920 40023 1 HOSEBARB, 1/2MPT X 3/8 DL 33 86026670 75277 1 TANK ASM, SOLUTION ADM8 ITEMS INCLUDED *

ADMIRAL 86038270 05/22/07 33 E E 16 15 5 7 4 12 11 10 1 9 12 2 6 17 13 8 18 14 3 1B 10B 11B 14B 12

ADMIRAL 86038270 05/22/07 34 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1A 86002400 20064 1 CLAMP, 2.0" WORM GEAR X .312 1000084015 1B 86002350 20002 1 CLAMP, 2.0” NYLON RATCHET 2 86233140 20041 1 CLAMP, 2.0" WORM GEAR 3 86008400 78499 1 TETHER, DRAIN PLUG 4 86003110 27816 2 COVER, REC. TANK 5 86235280 28060 1 DOME, CLP FAMILY 6 86003630 34351 1 FLOAT SHUT-OFF 7 86003910 35230 1 GASKET, DOME 8 86003930 35232 2 GASKET, PORT COVER 9 86004200 39353 1 HOSE, 1.5 X 12.0 DRAIN 10A 86004510 41391 1 HOSE, INSERT 1000084015 10B 86004450 40019 1 HOSEBARB, 1.5 DOUBLE MCHD 11A 86004500 41390 1 HOSE, CAP 1000084015 11B 86006240 66227 1 PLUG, DRAIN HOSE 12 86006600 70114 6 SCR, #10 X 3/4 PPHST TYPE B 13 86032270 75260 1 TANK, ADM RECOVERY 14A 86001370 140408 1 BRKT, HOSE HOOK 1000084015 14B 86001190 140133 1 BRKT, RECOVERY HOSE MTG 15 86002870 27417 1 CORD, 99807 1/8 X 12" 16 86242230 500009 1 LABEL, WARNING 17 86245930 50994 1 LABEL, ADMIRAL MAIN 18 86003330 28061 1 DOME ASM, CLP FAM

ADMIRAL 86038270 10/12/07 35 PART NO. PRV NO. DESCRIPTION SERIAL NO. FROM NOTES: 86001140 12514 BRUSH, 15L X 3.38OD 86001100 11045 BELT, 180J6 MICRO-V 86000900 09019 BEARING, 1.125ODX.500IDX.375 86004570 44067 JET BODY, MINI PROMAX BODY 86241680 44073 JET, MINI PROMAX 9503 86004770 47477 KIT, 230V FLOJET PUMP REPLACEMENT 86010570 84165 VALVE ASM 86003780 35171 GASKET, ACCESSORY PORT 86230110 14312 BREAKER, 7A 86002020 14949 BREAKER, 4A 86007140 72130 SWITCH, SPST 2-POSITION ROCKER 86007200 72162 SWITCH, DPDT3-POSITION ROCKER 86005420 53791 VAC MOTOR ASM, 230V 86007970 73864 STRAINER, 3/8 IN. NPT 60 MESH 86230760 140216 BRUSH SET, 230V VAC AMETEK 86135330 140688 BRUSH SET, 230V VAC MTR WINDSOR * 86003330 28061 DOME ASM, CLP FAMILY 86003630 34351 FLOAT SHUT-OFF 86006240 66227 PLUG, DRAIN HOSE