Windsor MPRO Operator Instructions Manual

Read these instructions before using the machine. Operating instructions (ENG) 86037780-AF 08/15/11

OVERVIEW The carpet extractor is a mains powered, portable extractor intended for commercial use. The appliance sprays a cleaning solution onto the carpet, agitates the wet carpet, and then extracts the soiled solution back into the unit’s recovery tank. The appliance can be fitted with an accessory tool for cleaning upholstery and stairs. Machine Data Log & Overview Warranty Registration Thank you for choosing our product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product. To register your product go to: http://warranty.karcherna.com/warrantyregistration.aspx

3 Table of contents Machine Data Log & Overview . . . . . . . . . . . . . . . . .2 Table of contents. . . . . . . . . . . . . . . . . . . . . . . . . . . .3 How to Use This Manual . . . . . . . . . . . . . . . . . . . . . .4 Safety IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . .5 HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . .7 GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . .9 Safety Label Location . . . . . . . . . . . . . . . . . . . . . . .10 Operation Technical Specifications . . . . . . . . . . . . . . . . . . . . .11 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Controls & Components . . . . . . . . . . . . . . . . . . . . .13 Filling The Solution Tank . . . . . . . . . . . . . . . . . . . .14 Operating the Machine . . . . . . . . . . . . . . . . . . . . . .15 Operating Machine With Accessory Tools . . . . . . .16 Maintenance Protect From Freezing . . . . . . . . . . . . . . . . . . . . . .17 Daily Regular Maintenance. . . . . . . . . . . . . . . . . . .17 Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . .17 Maintenance Instructions . . . . . . . . . . . . . . . . . . . .18 Brush Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Spray Jet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Brush Motor Removal . . . . . . . . . . . . . . . . . . . . . . .19 Pump Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Vacuum Motor Removal . . . . . . . . . . . . . . . . . . . . .20 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .21 PARTS Brush Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Decal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Frame & Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Handle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Tank & Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Vacuum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Wiring Diagram - Main 230V. . . . . . . . . . . . . . . . . 42 Wiring Diagram-Control Panel 115V. . . . . . . . . . . 44 Wiring Diagram-Vacuum, Brush Motor & Pump 115V . . . . . . . . . . . . . . . . . . . . . . . 46 Wiring Diagram-Control Panel 230V. . . . . . . . . . . 48 Wiring Diagram-Vacuum, Brush Motor & Pump 230V . . . . . . . . . . . . . . . . . . . . . . . 50 Hose Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

How to Use This Manual This manual contains the following sections: • HOW TO USE THIS MANUAL • SAFETY • OPERATIONS • MAINTENANCE • PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual. The model and serial number of your machine is located on the lower back panel. The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine. The MAINTENANCE section contains preventive main- tenance to keep the machine and its components in good working condition. They are listed in this general order: • Periodic • Daily/Regular • Troubleshooting The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information: • REF - column refers to the reference number on the parts illustration. • PART NO. - column lists the part number for the part. • PRV NO. - Reference number. • QTY - column lists the quantity of the part used in that area of the machine. • DESCRIPTION - column is a brief description of the part. • SERIAL NO. FROM - column indicates the first machine the part number is applicable to. When the machine design has changed, this column will indicate serial number of applicable machine. The main illustration shows the most current design of the machine. The boxed illus- trations show older designs. If column has an asterisk (*), call manufacturer for serial number. • NOTES - column for information not noted by the other columns. NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower left corner of the front cover.

5 Safety IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet. See Grounding Instructions. Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service. Use only indoors. Do not use outdoors or expose to rain. Do not allow machine to be used as a toy. Close attention is necessary when used by or near children. Use only as described in this manual. Use only manufacturer's recommended components and attachments. Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center. Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run machine over cord. Keep cord away from heated surfaces. Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord. Do not handle the electrical plug or machine with wet hands. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is intended for cleaning carpet only. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. This machine is not suitable for picking up health endangering dust. Turn off all controls before unplugging. Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors. This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. SAVE THESE INSTRUCTIONS

Safety CONSIGNES IMPORTANTES DE SÉCURITÉ Lors de l'utilisation d'un appareil électrique, il faut toujours observer des précau- tions élémentaires,qui comprennent parmi celles-ci : LISEZ BIEN L'ENSEMBLE DES CONSIGNES AVANT D'UTILISER CET APPAREIL. Cette machine est pour l’utilisation commerciale. Pour réduire les risques d'incendie, d'électrocution ou de blessure : Raccordez l'appareil à une prise adéquatement reliée à la terre. Voir les Consignes de mise à la terre. Ne laissez pas l'appareil sans surveillance lorsqu'il est branché. Débranchez l'appareil lorsqu'il n'est pas utilisé et avant tout entretien. Utilisez-le exclusivement dans des endroits fermés. Ne l'utilisez pas en plein air et ne le laissez pas sous la pluie. Ne pas permettre aux enfants dejouer avec l'appareil. Durant la manoeuvre de la machine, prendre garde aux personnes environnantes et notamment aux enfants. Utilisez-le exclusivement de la manière décrite dans ce manuel. Utilisez exclusivement les composants et les fixations recommandés par le fabricant. N'utilisez pas l'appareil si le cordon ou la fiche est endommagé(e). Observez toutes les consignes figurant dans ce manuel au sujet de la mise à la terre de l'appareil. Si l'appareil ne fonctionne pas correctement, s'il est tombé par terre, s'il est endommagé, s'il a été laissé dehors ou s'il a été plongé dans l'eau, veuillez le renvoyer à un centre d'entretien agréé. Ne tirez pas sur le cordon, ne portez pas l'appareil par le cordon, n'utilisez pas le cordon comme poignée, ne fermez pas une porte sur le cordon, ne tirez pas sur le cordon dans des angles ou des coins pointus. Ne faites pas passer l'appareil par-dessus le cordon. Maintenez le cordon à l'écart de surfaces chauffées.. Ne débranchez pas l'appareil en tirant sur le cordon. Pour le débrancher, empoignez la fiche, non pas le cordon. Ne manipulez pas la fiche ou l'appareil les mains mouillées. Ne faites pas fonctionner l'appareil si des ouvertures sont bouchées. Dégagez des ouvertures tous débris suscep- tibles d'entraver le passage de l'air. Cette machine est destinée pour nettoyer le tapis seulement. Ne pas ramasser quelque chose qui brûle ou fume, comme des cigarettes, des allumettes ou des cendres chaudes. Cet appareil n'est pas conçu pour aspirer des poussières dangereuses. Arrêtez toutes les commandes avant le débranchement. L'appareil peut déclencher un incendie s'il se trouve à proximité de vapeurs ou de matériaux inflammables. Ne faites pas fonctionner cet appareil à proximité de fluides, de poussières ou de vapeurs inflammables. Cet appareil est adapté à un usage commercial : par exemple dans les hôtels, les établissements scolaires, les hôpitaux, les usines, les magasins et les bureaux, à des fins plus étendues qu'un simple entretien de la maison. Les travaux de maintenance et de réparation doivent absolument être effectués par du personnel qualifié. Si de la mousse ou du liquide s'échappe de la machine, éteignez-la immédiatement. CONSERVEZ CES CONSIGNESS

HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage. FOR SAFETY: To Identify actions which must be followed for safe operation of equipment. Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel. FOR SAFETY: DO NOT OPERATE MACHINE: Unless Trained and Authorized. Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use only manufacturer approved replacement parts. 86037780 MINI EXTRACTOR Safety

DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante : AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou entraîner la mort. ATTENTION - Dangers ou méthodes dangereuses qui pourraient provoquer des blessures légères ou une détérioration du produit ou des biens immobiliers. POUR VOTRE SÉCURITÉ : ce signe permet d'identifier les mesures de précaution à prendre pour assurer un bon fonctionnement du matériel. Rendre compte immédiatement d'une défaillance ou d'une détérioration de la machine. Ne pas utiliser la machine si celle-ci ne fonctionne pas correctement. Lire soigneusement les informations ci-dessous signalant certains dangers potentiels pour l'opérateur de la machine. L'opérateur doit être absolument au courant de ces dangers potentiels. Localiser tous les dispositifs de sécurité sur la machine. Il est conseillé de prendre les mesures nécessaires pour former le personnel opérateur. POUR VOTRE SÉCURITÉ : NE PAS MANOEUVRER LA MACHINE : Lorsqu'on n'est pas expérimenté ou qualifié. Lorsque le guide d'utilisation n'est pas été lu ou compris. Dans des zones inflammables ou explosives. Dans des zones où des objets peuvent tomber. LORS DE L'ENTRETIEN DE LA MACHINE : Éviter les parties amovibles. Ne pas porter de vêtements amples, tels que des vestes, des chemises ou des vêtements avec manches lors de l'utilisation de la machine. Utiliser les pièces détachées Windsor homologuées. 86037780 MINI EXTRACTOR

USE ONLY. ELECTRICAL In the USA this machine operates on a standard 15 amp 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENSION CORDS If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length. GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunc- tion or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordi- nances. 120 VOLT MODELS This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in "Fig. A". A temporary adaptor that looks like the adaptor in "Fig. C" may be used to connect this plug to a 2-pole receptacle as shown in "Fig. B", if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or wire extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Le raccordement incorrect du conducteur de terre d'équipement peut entraîner des risques d'électrocu- tion. Vérifiez auprès d'un électricien qualifié ou d'un responsable de l'entretien si vous avez quelque doute que ce soit quant au raccordement à la terre de votre prise murale. Ne modifiez pas la fiche fournie avec l'appareil : si elle ne correspond pas à la prise murale, faites installer une prise adéquate par un électricien qualifié. 86037780 MINI EXTRACTOR GROUNDING PIN GROUNDED OUTLET ADAPTER METAL SCREW TAB FOR GROUNDING SCREW GROUNDED OUTLET BOX (A) (B) (C)

Safety WARNING LABEL PART NUMBER 86220140 PRV 500895 Safety Label Location The following WARNING LABEL(S) are found on your cleaning unit. These labels point out important Warnings and Cautions which should be followed at all times. Failure to follow warnings and cautions could result in fatality, personal injury to yourself and/or others, or property damage. Follow these instructions carefully! DO NOT remove these labels. NOTE: If at any time the labels become illegible, promptly replace them. Les ÉTIQUETTES D'AVERTISSEMENT suivantes se trouvent sur votre unité de nettoyage. Ces étiquettes signalent les avertissements et mises en garde importantes qui doivent être suivis en tout temps. Le non respect des avertissements et mises en garde pourrait entraîner des dommages matériels, des blessures graves ou même la mort. Suivez attentivement ces instructions ! NE PAS retirer ces étiquettes. REMARQUE : Si, à tout moment, les étiquettes deviennent illisibles, remplacez-les rapidement.

11 Operation Technical Specifications MODEL ITEM MEASURE ALL Vacuum Motor (1) 3 stage, 1.5hp 100 cfm (2.8cubic meters/min.) Waterlift - 120” (305cm) Floating Brush 10” (25.4cm) Main Jet Solution Pump Solenoid Style Accessory Solution Pump Solenoid Style Solution Capacity 4.6 Gal (17.3L) Recovery Capacity 3.9 Gal (14.7L) Brush Speed 1160 rpm Wheels (2) 10” dia. (25cm) by 2” (5cm) Vacuum Shoe 12” (30.48cm) cast aluminum Solution Spray 1 quick change jet Power cord 25’ (7.6m) (14 gauge) Height 39 inches (100cm) (Handle adjusted to highest position) Length 27 inches (69cm) (Handle adjusted to highest position) Width 14 inches (36cm) Weight 75 lbs. (34kg) 10080390 Electrical 115V, 15A, 60Hz 10080400 Electrical 230 V, 5A, 50Hz 10080410 10080420 Width Length Height

Operation To avoid electric shock use indoors only.To reduce risk of fire, do not use volatile substances. Use only cleaners intended for carpet application. Pour éviter une électrocution, utilisez la machine à l'intérieur seulement. Pour réduire les risques d'incendie, n'utilisez pas de substances volatiles. Utilisez seulement des nettoyants destinés à être appliqués sur les tapis. Inspection Carefully unpack and inspect your extractor for shipping damage. Each unit is operated and thor- oughly inspected before shipping, and any damage is the responsibility of the carrier, who should be notified immediately. To avoid possible distortion of polyethylene solution/ recovery tanks, DO NOT USE WATER TEMPERA- TURE THAT EXCEEDS 140°F (60° C). Pour éviter toute distorsion possible aux réservoirs de récupération /de la solution de polyéthylène, N’UTILISEZ PAS D'EAU DONT LA TEMPÉRATURE DÉPASSE 60° C (140° F). Chemicals Use only the suitable chemicals listed below. Using incompatible chemicals will damage the machine. Damages of this type are not covered under warranty. Carefully read ingredients on manufacturer's label before using any product in this machine. Suitable Chemicals Incompatible Chemicals Alkalis Aldehydes; Butyls Defoaming Agents Carbon Tetrachloride Detergents Chlorinated Bleaches Soaps Chlorinated Hydrocarbons Vinegar Trichlorethylene Hydroxides Phenols; Methyls (MEK) Perchlorethylene (perc) Aromatic Hydrocarbons D-Limonene

13 Operation Controls & Components 1. Power and Operation Mode Switch Turns accessory tool on or machine on. 2. Main Handle 3. Solution Button Sprays solution on floor when pressed. 4. Brush Motor Circuit Breaker Protects brush motor from overheating. 5. Vac Motor Circuit Breaker Protects the vac motor from overheating 6. Handle Adjustment Lever Adjusts handle position. 7. Solution Tank Drain Hose 8. Accessory Tool Connection Solution connection for accessory tools. 9. Accessory Hose Connection Hose connection for accessory tool. 10. Dome Clamp 11. Dome 12. Recovery Tank 13. Solution Tank 2 1 9 3 8 5 4 6 7 10 11 12 13

Operation Filling The Solution Tank 1. Release dome clamp. 2. Lift upper recovery tank from machine and set aside. 3. Use a clean bucket, recovery tank or hose to fill solution tank with hot water. The solution tank holds 4 gallons (15.2 liters) of cleaning solution. Add a non-foaming concentrate for use in hot water extractors at the proportions noted on the container. NOTE: Periodically operate the extractor with only hot water to remove chemical residue in carpet. To avoid possible distortion of the polyethylenesolution/ recovery tanks, DO NOT USE WATER WITH A TEMPERATURE THAT EXCEEDS 140°F(60°C). 4. Place recovery tank back on machine. Place dome on recovery tank. Make sure dome is seated correctly to ensure proper vacuum seal. Clamp dome securely to recovery tank. Use only the suitable chemicals listed in the Chemical Section. Using incompatible chemicals will damage the machine. Carefully read ingredients on manufacturer's label before using any product in this machine. SPECIAL NOTES: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowl- edge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be super- vised to ensure that they do not play with the appliance. The sound pressure level at the operator's ear was measured to be 73.7 dBA. This was a nearfield, broad- band measurement taken in a typical industrial environ- ment on a tile floor. This appliance contains no possible source of impact noise. The instantaneous sound pressure level is below 63 Pa. The weighted root mean square acceleration at the operator's arms was measured to be below 2.5m/s2. This was a tri-axial, third-octave-band measurement made during normal operation on a composite tile floor. The measurement and related calculations were made in accordance with ISO 5349-1.

15 Operating the Machine 1. Vacuum the carpet and make sure it is cleared of surface debris before cleaning. 2. Plug power cord into a grounded wall outlet. NOTE: Defeating the grounding pin on the power cord can result in a severe electrical shock. 3. Turn on the machine by pressing the switch in the normal operation mode. NOTE: The vacuum and the brush are protected by circuit breakers located on the control panel, to the right of the switch. NOTE: If either motor does not respond to being switched on, reset the circuit breakers by pressing them in, and attempt to switch the machine on again. NOTE: If solution does not dispense in an even pattern across the width of the machine, the spray jet may be clogged. Tilt the machine back, check for debris and clean surface of jet. NOTE: Do not use pins, wire, etc. to clean spray jet nozzle as this will deform the jet and destroy the spray pattern. 4. To operate the machine, pull straight back without pushing down on handle. Press the solution spray button to apply cleaning solution. 5. While operating machine, check for excessive foam buildup in the recovery tank. If excessive foam is present, add a defoamer solution to recovery tank, or empty tank. 6. Empty recovery tank when approximately 3/4 full. If the recovery tank is overfilled, the water will drain back onto the carpet when the vacuum is switched off. 7. Ventilate area after carpet has been cleaned. Keep children and pets away and do not walk on carpet until it is dry. A Windblower™ fan can be used to reduce drying time. Operation

Operation Operating Machine With Accessory Tools This extractor is easily adapted for use with Windsor accessory tools: Contact Customer Service for details. 1. Disconnect vacuum hose at dome, insert hose cuff into the dome, ensuring that there is a tight fit. Dome must be clamped to recovery tank. 2. Attach the solution hose from accessory tool to the brass solution fitting on the back of machine. 3. Turn on the switch in the accessory position. The application of cleaning solution is now controlled by the lever on the accessory tool. NOTE: The solution pump is not intended to run dry. When using the extractor for vacuum pick-up only. Do not press the solution spray button. This appliance is not suitable for picking up hazardous dust. Cet appareil n'est pas conçu pour aspirer des pous- sières dangereuses.

17 Maintenance Protect From Freezing If it becomes necessary to store in temperatures that could drop below 40°F, the pumping system, hoses and valves must be protected from freezing with a methyl hydrate window washer antifreeze solution. NOTE: Do not use ethylene glycol or cooling system antifreezes. 1. Add one gallon of window washer antifreeze to the supply tank. 2. Turn on pump switch and spray until the anti-freeze solution fills the solution lines. 3. Drain the leftover antifreeze from the supply tank. Always allow the unit to reach room temperature before filling with hot water or operating. 4. Before operation be sure to flush system completely. Failure to do so after winterizing machine will damage carpet. Daily Regular Maintenance Before making any adjustments or repairs to the machine, disconnect the power cord from the elec- trical source. 1. Empty unused cleaning solution from the solution tank. 2. Inspect and clean filter at solution tank fill port and at the vacuum intake port in the dome. 3. Flush pumping system with 1 to 2 gallons of clean, hot water. 4. Check spray jet for full spray pattern. 5. Empty the recovery tank and rinse with clean water. 6. Check for and remove any lint or debris around brush and vac shoe. 7. Clean float screen and check float valve to make sure it moves freely. Periodic Maintenance 1. After every 25 hours of operation, flush a white vinegar solution (ONE quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. 2. If the spray jet becomes clogged, check for debris and clean surface of jet. NOTE: Do not use pins, wire, etc. to clean spray jet nozzle as this will deform the jet and destroy the spray pattern. 3. Periodically inspect all hoses, electrical cables, filters, gaskets and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. 4. The electrical cable must be well insulated, if the cable insulation is broken or frayed, repair or replace it immediately. Don't take chances with electrical fire or shock. 5. The filter in the bottom of the solution tank and at the fill port must be clean to allow free flow of cleaning solution. The screen filter on the vacuum intake in the dome must be free of lint buildup to ensure full vacuum strength. 6. The dome gasket must be properly seated and free of damage to create the air seal needed to extract water.

Maintenance Maintenance Instructions Remove machine power cord from electrical source before making any adjustments or repairs to the machine. Retirez le cordon d'alimentation de la machine de la source électrique avant de procéder à des répara- tions ou des ajustements de la machine. Only qualified maintenance personnel are to perform repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations. Brush Assembly 1. Turn off switch and unplug machine. 2. Position the machine to have access to the bottom. Remove screws (2) at the sides of the machine holding the brush deck pivot axle. 3. Remove screw mounting belt cover and remove belt cover. 4. Loosen the nuts (2) at brush motor and slide motor forward to reduce belt tension. Remove belt. 5. Loosen set screw on brush pulley. Remove pulley. 6. Remove screws (4) mounting brush bearings to frame. Slide bearing off brush axle. 7. Remove brush by lifting drive end out of frame and sliding other end out of bearings mounted to frame. 8. Inspect/replace brush and bearings as required. The brush is equipped with yellow wear indicator bristles. Replace the brush when it wears down to the height of the yellow bristles. 9. Reverse the process to reinstall the brush and bearings. Check belt for proper belt tension. Only use the brushes provided with the appliance or those specified in the instruction manual. The use of other brushes may impair safety. N'utilisez que les brosses fournies avec l'appareil ou celles qui sont spécifiées dans le manuel d'instructions. L'utilisation d'autres brosses peut nuire à la sécurité. Spray Jet NOTE: To prevent a clogged jet due to alkali build- up, the spray system should be flushed with 1 to 2 gallons of clean hot water at the end of each day. 1. Turn off switch and unplug machine. 2. Position the machine to have access to the bottom. Remove screws (2) at the sides of the machine holding the brush deck pivot axle. 3. Position the machine to have access to the bottom. 4. Pull off the clip mounting the jet to the frame. Push the jet and hose out of the mounting hole in the frame. 5. Loosen the hose clamp and pull the jet out of the hose. 6. Reverse the process to reinstall the jet. Be sure to have jet rotated correctly before installing clip. Clip tab must face back of machine. NOTE: Do not use pins or wire to remove obstruction if clogged, this may damage jet and alter spray pattern.

19 Maintenance Brush Motor Removal 1. Turn off switch and unplug machine. 2. Set the machine in its upright position. Remove the screws (2) in the back metal cover. Rotate the cover down and slide back releasing the tab under the machine from the main frame. 3. Remove the pump box cover. Remove screws (4) at each leg of the cover. 4. To remove brush motor, position the machine to have access to the bottom. Remove screws (2) at the sides of the machine holding the brush deck pivot axle. 5. Remove screw mounting belt cover and remove belt cover. 6. Remove the nuts and washers (2) at brush motor and slide motor forward to reduce belt tension. Remove belt. 7. Remove pulley by loosening set screw and pull off shaft. 8. Unplug the brush motor wires from the rectifier located in the pump mount housing. Also, remove the ground lug from the stud on the main frame by removing the nut on the stud. 9. Reverse the process to reinstall the motor. Align motor pulley with brush pulley. Check belt for proper belt tension. Pump Removal 1. Turn off switch and unplug machine. 2. Set the machine in its upright position. Remove the screws (2) in the back metal cover. Rotate the cover down and slide back releasing the tab under the machine from the main frame. 3. Remove the pump box cover. Remove screws (4) at each leg of the cover. 4. To remove either pump, loosen the hose clamp and remove the hose from both ends of the pump. 5. Remove screws and washers (4) that mount pump housing. 6. Unscrew the hose fittings from each end of the pump. 7. Flex the pump mounting housing to remove the pump. 8. Remove the screw attaching the ground wire to the pump. Remove the other two wire connectors attached to the pump. 9. Reverse the process to reinstall

Maintenance Vacuum Motor Removal 1. Turn off switch and unplug machine. 2. Set the machine in its upright position. Remove the screws (2) in the back metal cover. Rotate the cover down and slide back releasing the tab under the machine from the main frame. 3. Remove the pump box cover. Remove screws (4) at each leg of the cover. 4. Remove vacuum hose, loosen hose clamp and pull hose from bottom of vacuum motor. 5. Unplug wires (2) from main harness located in pump mount housing. Remove ground from stud on main frame. 6. To remove the vacuum motor, remove the screws (2) in the back of the machine that mount the plastic cover to the solution tank. 7. Remove the screws (3) that mount the vacuum motor to the plastic cover. Pull the cover off the vacuum motor. 8. Unscrew the ground wire from the vacuum motor. 9. Reverse the process to reinstall the vacuum motor. NOTE: Make sure the excess wire lengths do not get pinched between the vacuum motor and plastic cover. NOTE: The vac motor is protected by a circuit breaker located in the switch panel. The breaker will only trip under conditions of abuse. 3 8 [9.5mm] Vacuum Motor Carbon Brushes Carbon Brushes End Cap If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. Inportant: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely. Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less tan 3/8" (9.5mm) long.

21 Maintenance Troubleshooting PROBLEM CAUSE SOLUTION No power, nothing runs. Is the cord plugged in. Plug in cord. Circuit breaker tripped in building. Reset breaker. Faulty switch. Call for service. Faulty power cord or pigtail. Call for service. Vacuum motor will not run. Vacuum circuit breaker tripped. Reset breaker. Faulty main switch. Call for service. Loose wiring. Call for service. Faulty vac motor. Call for service. Vacuum motor runs but suction is poor. Debris lodged in vac shoe. Remove debris from vac shoe. Dome gasket defective or missing. Replace as necessary. Vacuum hose cracked or hose cuff loose Replace or repair as necessary. Recovery tank full. Turn off vac motor. Drain and rinsere- covery tank. Poor or no water flow. (carpet is streaky) Switch to accessory mode. Turn to deep clean position. Jets clogged or missing. Jets clogged or missing. Solution filter clogged. Drain solution tank and clean solution- filter. Faulty solution pump. Call for service. Brush does not spin. Switch in accessory mode. Turn to deep clean position. Brush circuit breaker tripped. Reset circuit breaker. Brush belt broken. Replace as necessary. Faulty brush motor. Call for service. Accessory tool fitting difficult to connect Corrosion on fitting. Clean with steel wool. Remove and soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant.

Squealing or grinding sound in brush housing. Replace bearings. Carpet not getting clean Severe soil conditions Make several passes at right angles to each other. Use a pre-spray. Carpet too wet Worn spray jet Replace spray jet which is producing a fine mist. Carpet not getting wet Solution filter screen clogged. Clean solution filter screen located inside lower tank. Spray jet clogged. Clean or replace jet. Do not use a wire to clean jet. Damaged jet will cause over-saturation. Pump not running. Check for and correct any loose wires. Repair or replace. Faulty solution switch. Replace switch in handle. 86037780 MINI ETRACTOR

25 Brush Deck REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86173020 70916 5 SCR, M5 X 10, PHMS, ISO7045, SS 2 86217390 270146 1 COVER, PULLEY, BRUSH DECK 3 86215260 11051 1 BELT, HTD 5MM 69T 9 WIDE 4 86223780 70896 2 SET SCR, M4 X 6LG, CP BLK 5 86223300 64115 1 PULLEY, BRUSH 6 86214970 03124 1 AXLE, PIVOT, BRUSH DECK 7 86229020 09163 2 BEARING, BRUSH PLASTIC 8 86005640 57030 2 NUT, 10-32 HEX NYLOCK 9 86173330 87513 2 WASHER, M5, FLAT, ISO7093, SS 10A 86247110 53146 1 MOTOR, 115V BRUSH DRIVE 115V ONLY 10B 86306720 - 1 MOTOR ASM, 230V DC PM 230V ONLY 11 86217920 140893 1 BRKT, FLOATING BRUSH, 10 IN 12 86223490 67468 2 RING, 10MM EXT SNAP, DIN 471 13 86216430 140912 2 BUSHING, BRUSH PRESSURE 14 86216040 02506 1 BRUSH, CHEVRON, 10 IN 15 86173220 70954 2 SCR, M6X12 PHCS, 12.5MM HD,SS 16 86223350 64125 1 PULLEY, MOTOR 17 86010680 87030 1 WASHER, 3/8 ID X 3/4 OD NYLON

27 Control Panel SEE WIRING DIAGRAM FOR WIRE CONNECTIONS. REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86007200 72162 1 SWITCH, DPDT 3-POSITION ROCKER 2 86002010 14942 2 BOOT, 3/8 CIRCUIT BREAKER 3 86173140 70945 2 SCR, KA40X16, PT OVAL, WN1412, PL 4 86217410 270152 1 COVER, CONTROLS TOP 5A 86230140 14622 1 BREAKER, 1.5A CIRCUIT 115V ONLY 5B 86001780 14308 1 BREAKER, 0.8A CIRCUIT 230V ONLY 6A 86291460 - 1 BREAKER, 11A VDE CIRCUIT 115V ONLY 6B 86198130 141047 1 BREAKER, 6A VDE CIRCUIT 230V ONLY 7 86223420 67622 1 RELAY, 10A 230VAC SPDT 230V ONLY 8 86302680 - 1 EMI FILTER MAIN 230V ONLY 9 86292300 - 2 SCR, M4X20 SBHCS, BLK EDP 10 86173350 87515 2 WASHER, M5, FLAT, ISO7089, SS 11 86216300 140956 2 BUMPER, CONSOLE

29 Decal REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86221090 501128 1 LABEL, CONTROL PANEL 2 86221470 501208 1 LABEL, DOME ACCESSORY 3 86013720 - 1 LABEL, MINI EXT.INSTRUCTION

31 Frame & Wheels REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86215830 140897 1 BRKT, BRUSH HOUSING, 10 IN 2 86173010 70915 6 SCR, M4 X 16, SHCS, ISO4762, SS 3 86216290 140895 1 BUMPER, EXTRACTOR, FRONT 4 86218090 35360 1 GASKET, VAC SHOE 5 86225530 85086 1 VAC SHOE, 12 IN 6 86172630 57314 6 NUT, M4, LOCK, ISO7040, SS 7 86173220 70954 6 SCR, M6X12 PHCS, 12.5MM HD, SS 8 86226050 89279 2 WHEEL, 10IN 9 86011880 - 2 WASHER, 16.2 X 23 X 0.6MM, PLT 10 86214980 03125 1 AXLE, WHEELS, 5/8 DIA 11 86272750 67010 2 RING, 5/8 EXTERNAL SNAP 12 86219480 41567 2 HUBCAP, 9.75" WHEEL 13 86291130 - 1 BUMPER, BRUSH DECK

Handle 27 8 41 42 43 13 19 20 21 22 23 26 28 7 6 5 47 48 46 49 18 17 44 13 29 30 31 36 34 33 32 25 24 35 37 38 45 40 9 10 11 12 14 16 15 4 3 2 1 24 37 36 31 39

33 Handle REF PARTNO. PRV NO. QTY DESCRIPTION SERIAL NO.FROM NOTES 1 86012660 - 3 SCR, KA40X25, PT OHCS,WN1452,PL 2 86218570 38342 1 HANDLE, GRIP BOTTOM 3 86225910 38343 1 WELDMENT, HANDLE TUBE 4 86218560 38341 1 HANDLE, GRIP TOP 5 86225140 72204 1 SWITCH, MICRO 6 86224650 730392 1 SPRING, LEVER 7 86216470 140922 1 BUTTON, SPRAY HANDLE 8 86219460 41553 1 HUB, SPLINE HANDLE 9 86216440 140934 1 BUSHING, SHAFT HANDLE 10 86219660 48113 1 KEY, HANDLE CAM, 4X24MM 11 86221790 51548 1 LEVER CAM HANDLE 12 86217360 270138 1 COVER, TUBE HUB LEFT 13 86277600 70882 3 SCR, M4 X 20, PHMS, ISO7045, SET 14 86008650 80604 1 COTTER, 1/4" RING 15 86222600 66887 1 PIN, CLEVIS 5MM 16 86224150 730405 1 SHAFT, HANDLE CAM 17 86222340 57512 1 NUT, M12, LOCK. ISO 7040, SST 18 86259430 87485 1 WASHER, M12 FLAT 19 86173220 70954 4 SCR, M6X12 PHCS, 12.5MM HD, SS 20 86224930 730012 1 STRAIN RELIEF, 14/3 STRAIGHT 21 86224460 730406 1 SPACER, SHAFT HANDLE 22 86224140 730404 1 SHAFT, HANDLE 23 86217380 270144 1 COVER, TUBE HUB RIGHT 24 86010640 87016 2 WASHER, #10 LOCK EXT STAR 25 86270800 57014 1 NUT, 10-32 HEX SS 26 86217350 270135 1 COVER, CONTROLS, BOTTOM 27 86172870 70898 4 SCR, M4X14 PHMS, DIN7985 SST 28 86215520 140921 1 BRACKET, HANDLE AXLE 29 86233170 20054 1 CLAMP, 3/8 NYLON UL/CSA 30A 86217140 23732 1 CORD ASM, 14X3 SJTX25' 115V ONLY 30B 86288380 23706 1 CORD ASM, AB EURO 230V ONLY 30C 86217030 23710 1 CORD ASM, AUST AB 230V ONLY 31 86173030 70917 3 SCR, M4 X 6, PHMS, ISO7045, PL 32 86005640 57030 1 NUT, 10-32 HEX NYLOCK 33 86218230 35376 1 GASKET, CONTROL BOX RIGHT 34 86218220 35375 1 GASKET, CONTROL BOX LEFT 35 86013730 - 1 SHEILD, MICROSWITCH 36 86173320 87510 3 WASHER, FLAT M4 DIN125 SST 37 86006770 70323 2 SCR, 10-32 X 1/4 PH PLTD 38 86288680 87230 4 WASHER, M5 RIVET BACKUP 39 86266080 76040 1 TERM, 18G .25 FEMALE COUPLER 40 86296620 - AS REQ’D WASHER, 0.2X19.8C25.0MM PLTD *(2) 41 86292550 - 1 BUSHING, HANDLE LOCK *(2) 42 86296610 - 1 LEVER, CAM HANDLE *(2) 43 86296600 - 1 COVER, HUB TUBE LEFT *(2) 44 86292560 - 1 SHAFT, HANDLE LOCK *(2) 45 86266630 - 1 PIN, DOWEL 5 X 25MM, PLTD *(2) 46 86297150 - 1 HANDLE, GRIP TOP *(1) 47 86297160 - 1 HANDLE, GRIP BOTTOM *(1) 48 86298790 - 1 WELDMENT, HANDLE TUBE *(1) 49 86173140 70945 4 SCR, KA40 X 16, PT OHCS, WN1452PL *(1)

35 Solution REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1A 86201110 250-78 2 PUMP, 110/120 60HZ FLOJET 115V ONLY 1B 86201120 250-78A 2 PUMP, 220/240V 50HZ FLOJET 230V ONLY 2 86240520 40097 4 HOSEBARB, 1/8MPT X 1/4 90D 3 86010640 87016 2 WASHER, #10 LOCK EXT STAR 4 86006770 70323 2 SCR, 10-32 X 1/4 PHTR PLTD 5 86215450 140930 1 BOX, PUMP MOUNT 6 86304750 - 1 SHEILD, PUMP ENCLOSURE *(1)

37 SEE HOSE DIAGRAM FOR HOSE ROUTING. REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86219580 44106 1 JET, RT ANG, 1/4 BARB 2 86216810 270131 1 CLIP, SHAFT, 9-12MM 3 86219200 40114 1 HOSEBARB, 3/8MPT, 2 X 1/4. 1 X 3/8 4 86172950 70909 4 SCR, M5X12, SHCS, ISO4762, SS 5 86233150 20042 3 CLAMP, 3/8 HOSE (D-SLOT) 6 86219090 39728 1 HOSE, 3/8" X 432MM CLEAR 7 86200820 270-11A 1 NIPPLE, 1/8FPT QD MALE BRASS 8 86219070 39726 1 HOSE ASM, 6MM X 610MM NYLOBRAID 9 86219080 39727 1 HOSE, 6MM X 245MM NYLOBRAID 10 86233090 20016 7 CLAMP, 1/4 ID HOSE 11 86289330 40062 1 HOSEBARB, TEE 3/8 X 3/8 X 1/4 12 86219050 39724 1 HOSE, 6MM X 390MM NYLOBRAID 13 86240430 40083 1 HOSEBARB, 3/8 MPT X 3/8 NYLON 14 86012680 - 1 HOSE, 3/8ID X 60MM NYLOBRAID 15 86005640 57030 1 NUT, 10-32 NYLOCK 16 86010640 87016 1 WASHER, #10 LOCK EXT STAR SS 17 86219060 39725 1 HOSE, 6MM X 420MM NYLOBRAID 18 86291670 - 1 COVER, PUMP BOX

39 Tank & Dome REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86225240 75471 1 TANK, SOLUTION, EXTRACTOR 2 86002390 20063 2 CLAMP, 1.75" WORM GEAR X .312 3 86011910 - 2 HOSE ASM, 1.5X34" VAC W/ELBOW 4 86291230 - 1 GASKET, DOME, MINI PRO 5 86217700 28070 1 DOME 6 86291170 - 1 DOME, PLATE INTERIOR 7 86291190 - 1 SCREEN, VACUUM INTAKE 8 86007970 73864 1 STRAINER, 3/8 IN. NPT 60 MESH 9 86172940 70908 6 SCR, KA40X10,PT OVAL, WN1412,PL 10 86224960 730373 1 STRAINER, BASKET 11 86172990 70913 4 SCR, M6X12 BHCS, ISO7380, SS 12 86218530 38338 1 HANDLE, RECOVERY TANK 13 86225260 75472 1 TANK, RECOVERY, EXTRACTOR 14 86216770 22113 1 CLAMP, DOME 15 86215970 141049 2 BRKT, DOME CLAMP 16 86173350 87515 4 WASHER, M5, FLAT, ISO7089, SS 17 86291180 - 1 DUCT, VACUUM INTAKE 18 86291210 - 1 O-RING, 26MM ID X 2MM THICK 19 86173000 70914 2 SCR, KA40X20, PT OVAL, WN1412,PL 20 86291220 - 2 SCR, KA40X16, PT, WN1413, SS 21 86292450 - 1 GASKET, DUCT

41 Vacuum REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86173000 70914 3 SCR, KA40x20, PT OHS, WN1412, PLTD 2A 86225480 53272 1 VAC MOTOR, 120V 5.7 3ST W/TUBE 115V ONLY 2B 86308980 - 1 VAC MOTOR ASM, 230V MINIPRO 230V ONLY 3 86173220 70954 4 SCR, M6X12 PHCS, 12.5MM HD, SS 4 86217420 270703 1 COVER, VAC MOTOR 5 86217370 270140 1 COVER, LOWER BACK 6 86006770 70323 1 SCR, 10-32 X 1/4 PHTR PLTD 7 86010640 87016 1 WASHER, #10 LOCK EXT STAR 8 86291680 - 1 GASKET, VAC MOTOR

Wiring Diagram - Main 230V ge ws ge rt bn ws or sw ws ws A 1.5 A 1.2 L N G OFF OFF 230V/50Hz Z4 1 02 1 02 25A 6A 8A Z3 Z5 4 2 3 1 bl sw bn rt ws ge 1 5 3 /1.4 2 6 4 /1.3 7 8 -K1 rt rt bn sw sw bl rt bl ws bn ge 1~ M 1~ M 1~ M 1 2 -M2 1~ M 1~ M 1~ M 1 2 -M3 1~ M 1~ M 1~ M 1 2 -M4 5 4 6 -S1 2 1 3 ws ws bl bn bl sw bn bn rt ge ws sw ge ge ge bl bn sw ws ws rt 1 2 -F1 1 5 3 -K1 /1.5 2 6 4 -K1 /1.5 1 2 -F2 1 2 -F3 NC C NO -S2 - ˜ ˜ + -V1 M 1 2 -M1 -Z1 -U1 -Z2 ws sw

43 Wiring Diagram - Main 230V REFERENCE DESCRIPTION F1 25 AMP FUSE F2 8 AMP CIRCUIT BREAKER F3 6 AMP CIRCUIT BREAKER K1 MAIN RELAY S1 MAIN SWITCH LINE ON/OFF/ACCESSARY S2 SWITCH X* SEE SCHEMATIC Z1 FILTER Z2 FILTER Z3 FERRITE BEAD Z4 FERRITE BEAD Z5 FERRITE BEAD V1 RECTIFIER M1 BRUSH MOTOR M2 VACUUM MOTOR M3 PUMP MOTOR M4 PUMP MOTOR U1 6 CONDUCTOR CABLE

Wiring Diagram-Control Panel 115V BLK PEM STUD MODE SWITCH HANDLE MICRO SWITCH C NC NO BLK BLU 1.5A BREAKER BRUSH MOTOR 11A BREAKER VAC MOTOR BLK BLK 3 CONDUCTOR 18 GUAGE BLACK SHEATH 6 CONDUCTOR 14/16 GUAGE BLACK SHEATH FORWARD = ACCESSORY TOOL CENTER = OFF BACK = EXTRACT GRN YEL RED GRN WHT TOP OF MACHINE GROUND SCREW "BACK POSTION" "FORWARD POSITION" BLK 3 2 1 4 5 6 BLK P/N 880464 BLK RED RED BRN GRN WHT BLK BLU 3 CONDUCTOR 12 GUAGE YELLOW SHEATH YEL RED YEL FRONT OF CONSOLE GRN CONNECTOR MODE SWITCH 1 2 3 4

45 Wiring Diagram-Control Panel 115V REF PARTNO. PRV NO. QTY DESCRIPTION SERIAL NO.FROM NOTES 1 86218840 41573 1 HARNESS, MAIN 2 86226230 880464 1 WIRE ASM, CONTROL PANEL JUMPER 3 86218830 41572 1 HARNESS, HANDLE 4 86226250 880466 1 WIRE, 14" BLACK/14 76010

Wiring Diagram-Vacuum, Brush Motor & Pump 115V BLK WHT GRN BRN RED WHT BLU BLK GRN GRN GRN CONNECTOR G R N GRN G R N GRN GRN DASH LINE = PUMP BOX OUTLINE PUMP ACC PUMP MAIN GRN GRN GRN BACK COVER VAC MOTOR BRUSH MOTOR 1 1 4 3 2 WHT WHT BLK WHT BRN WHT RED BLK WHT FULL BRIDGE RECT PEM STUD BOTTOM OF MACHINE BLU

47 Wiring Diagram-Vacuum, Brush Motor & Pump 115V REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86226250 88884 3 WIRE, 14" GRN/14 76008 X 76008 2 86223460 67499 1 RECTIFIER, 50A 1000V BRIDGE 3 86303670 - 1 WIRE ASM, 18 GA GRN 76008/76040 4 86303680 - 1 WIRE ASM, 18 GA GRN 76008/76042

Wiring Diagram-Control Panel 230V BLK BLK FORWARD = ACCESSORY TOOL CENTER = OFF BACK = EXTRACT GRN YEL RED TOP OF MACHINE GROUND SCREW "BACK POSTION" "FORWARD POSITION" 3 2 1 4 5 6 R E D RED BRN GRN WHT BLK BLU 3 CONDUCTOR 12 GUAGE YELLOW SHEATH YEL RED YEL FRONT OF CONSOLE GRN GRN W H T EMI FILTER GRN B L U B R N B R N B L U BLK 1 2 4 3 5 6 8 7 RED R E D BLK W H T O R G W H T B L K W H T WHT WHT FUSE 25A P/N 86305240 RELAY 3 CONDUCTOR 18 GUAGE BLACK SHEATH .8A BREAKER BRUSH MOTOR 6A BREAKER VAC. MOTOR 1 2 3 4 5 6 7 8 9 6 CONDUCTOR 14/16 GUAGE BLACK SHEATH PEM STUD MODE SWITCH MICRO SWITCH C NC NO BLU

49 Wiring Diagram-Control Panel 230V REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86218840 41573 1 HARNESS, MAIN 2 86218830 41572 1 HARNESS, HANDLE 3 86012400 - 1 WIRE ASM, 18GA 4" BLK 4 86012420 - 1 WIRE ASM, 18GA RED 5 86226250 880466 1 WIRE, 14" BLACK/14 76010 6 86012430 - 1 WIRE ASM, 18GA WHT 7 86012410 - 1 WIRE ASM, 18GA 4" ORG 8 86302680 - 1 ASM, FILTER EMI MAIN 9 86223420 67622 1 RELAY, 10A 230VAC SPDT

Wiring Diagram-Vacuum, Brush Motor & Pump 230V PUMP MAIN PUMP ACC VAC MOTOR FULL BRIDGE RECT BACK COVER BOTTOM OF MACHINE BLU BLK WHT GRN BRN RED DASH LINE = PUMP BOX OUTLINE EMI FILTER FERRITE RED GRN GRN GRN GRN GRN GRN GRN GRN GRN GRN GRN WHT WHT WHT WHT WHT WHT WHT W H T BLK BLK BLK B L K BLK BRN BRN BLU BLU BLU BRN GRN GRN B L K W H T GRN GRN 3 2 7 1 1 4 5 FERRITE BRUSH MOTOR FERRITE 8 8 6

51 Wiring Diagram-Vacuum, Brush Motor & Pump 230V REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86226310 88884 2 WIRE, 14" GRN/18 76008 X 76008 2 86308960 - 1 ASM, FILTER EMI BRUSH 3 86223390 67488 1 RECTIFIER, 50A 600V BRIDGE 4 86303680 - 1 WIRE ASM, 18 GA GRN 76008/76042 5 86303670 - 1 WIRE ASM, 18 GA GRN 76008/76040 6 86302670 - 1 FERRITE, AXIAL LCR 3.007.1943 7 86309300 - 1 WIRE, 30.5" GRN/18 76008 X 76008 8 86311030 - 2 FERRITE, WURTH 74270115

Hose Diagram (86240430) (86219050) (PRV 39724) (86219090) (PRV 39728) (PRV 40114) (86012680) (86219090) (PRV 39725) (86219080) (PRV 39727) (86219070) TO SOLUTION TANK ACCESSORY PUMP MAIN PUMP ACCESSORY TOOL JET TO SOLUITON TANK (PRV 44106) (86240520) (PRV 40062) (PRV 40083) (PRV 40097) 4X (86200820) (PRV 270-11A) (PRV 39726) (86219580) (86289330) (86219200)

53 Spare Parts Accessories PART NO. PRV NO. DESCRIPTION SERIAL NO. FROM NOTES 86216430 140912 BUSHING, BRUSH PRESSURE 86229010 09163 BEARING, BRUSH 86216040 02506 BRUSH, CHEVRON, 10 IN 86223350 64125 PULLEY, MOTOR 86223300 64115 PULLEY, BRUSH 86215260 11051 BELT, HTD 5MM 69T 9 WIDE 86247110 53146 MOTOR, 115V BRUSH DRIVE 115V ONLY 86306720 - MOTOR, 230V DC PM 230V ONLY 86217390 270146 COVER, BELT GUARD 86218090 35360 GASKET, VAC SHOE 86219580 44106 JET, RT ANG, 1/4 BARB 86201110 250-78 PUMP, 110/120 60HZ FLOJET 115V ONLY 86201120 250-78A PUMP, 220/240V 50HZ FLOJET 230V ONLY 86224960 730373 STRAINER, RECT, 80 MESH SS 86225480 53272 VAC MOTOR, 120V 5.7 3ST W/TUBE 115V ONLY 86308980 - VAC MOTOR ASM, MINIPRO 230V 230V ONLY 86135320 140687 BRUSH SET, 120V VAC 115V ONLY 86135330 140688 BRUSH SET, 230V VAC MTR 230V ONLY 86291230 - GASKET, DOME 86291190 - SCREEN, DOME VAC INTAKE 86291460 - BREAKER, 11A VDE CIRCUIT 115V ONLY 86230140 14622 BREAKER, 1.5A CIRCUIT 115V ONLY 86215720 141047 BREAKER, 6A VDE CIRCUIT 230V ONLY 86001780 14308 BREAKER, 0.8A CIRCUIT 230V ONLY 86002010 14942 BOOT, 3/8 CIRCUIT BREAKER 86007200 72162 SWITCH, DPDT3-POSITION ROCKER 86349430 - CHECK VALVE KIT PART NO. PRV NO. DESCRIPTION 86218790 HTO HANDTOOL W/1/8 FEM QD (INCLUDES HOSE ASM) 86290360 - HANDTOOL KIT (INCLUDES HOSE ASM AND CARRY BAG)

1 MPRO, MPROEU, MPROGB, MPROAU:1008039000126 2 MPRO, MPROEU, MPROGB, MPROAU:1008039000001 86037780 MINI ETRACTOR