Salter Brecknell MS-20 Operation & User’s Manual

from the below UK address: Electromagnetic Compatibility Statement for North America This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Re-orient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. USER'S MANUAL Model MS-20 IN-0787 3014H Declaration of Conformity Manufacturer Salter Brecknell Type MS-20 Corresponds to the requirements of the following EC directives Electro Magnetic Compatibility Directive EMC 89/336/EEC Low Voltage Directive LVD 73/23/EEC The application harmonised standards are: EN60950, EN50081-1 EN50082-1 Salter Brecknell Weighing UK & Europe PO box 9533, Smethwick, West Midlands, B66 2TE United Kingdom Tel: +44 (0) 870 444 6132 Fax: +44 (0) 870 010 2241 Email: sales @salterbrecknell.co.uk Salter Brecknell Weighing Products USA 1000 Armstrong Drive, Fairmont, MN56031 Toll Free: 800-637-0529 Phone: 507-238-8702 Fax: 507-238-8271 Email: [email protected] www.salterbrecknell.com

To insure that your scale operates correctly, position the scale on a level sturdy worktop. The display head can be either attached to the wall or positioned in front of the scale. Pull down feet on back of display head enable the operator to change the viewing angle of the display head. Any excess cable can be stored in the cavity on the underside of the display head.
POWER SUPPLY The MS-20 uses 9V alkaline battery or 9V 100mA AC adapter. CAUTION: always connect the AC adapter to the MS-20 before connecting to the mains power supply. Disconnect from the mains power supply before disconnecting the adapter from the MS-20
KEY FUNCTION ON/TARE (1) Press once to switch scale on. OFF - (2) Press while scale is switched on to re-zero the scale. (3) Press and hold this key for 2 seconds to switch scale off. Scale will auto shut-off if not used after 120 seconds UNIT - Selects between kg mode and lb mode. HOLD - When pressed the displayed weight will be held on the display once the weight becomes stable. By repressing the Hold key again will release the held display and allow the scale to return back to normal weighing mode.

ERROR MESSAGES 1. Low Battery 2. High zero counts 3. Low zero count 4. Overload
SPECIFICATIONS Model # MS-20 Maximum Capacity 44 lb / 20 kg Readability ½ oz / 10 g Weight units lb / kg Power supply 9V alkaline battery or 9V 100mA AC adapter Dimensions 20” x 12” x 2 ½” / 505mm x 300mm x 65 mm Display 1.0” LCD display with 4 active digits Tray Plastic top cover Operating Temperature 5°C ~ 35°C Function keys ON/TARE/OFF, UNIT, HOLD CALIBRATION PROCEDURE 1) With the scale switched off, press and hold the “ON/OFF/TARE key, without releasing press the kg/lb key three times and then release. 2) Display will show zero (4000~12000). 3) Press the “UNITS” key, switch to LB mode or KG mode 4) Press “ON/OFF/TARE” key once. 5) Display will show “CAL” and then “0”. 6) Load 20kg weight onto the scale, or load 40 lb in case of switched to LB mode at step 3. 7) Display will show span count (8000~16000) for KG mode or (7260~14520) for LB mode. 8) Press “ON/OFF/TARE” key again. 9) Display will show “CAL” and then “20.00 kg” for KG mode or “40:00 lb” for LB mode 10) Remove the weight from the scale and the calibration is finished.