Samsung SDC-435 Operation & User’s Manual

please read this manual thoroughly. Ultra High Resolution Camera SDC-435 User Guide ENGLISH

should conform to all local codes. The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. INFORMATION-This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING : Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. WARNING : To prevent electric shock and risk of fire hazards: ◆ Do NOT use power sources other than that specified. ◆ Do NOT expose this appliance to rain or moisture. Thank you for purchasing a SAMSUNG CCD CAMERA. Before operating the camera, confirm the camera model and correct input power voltage. In order to that you can understand this manual thoroughly, we will explain the model pert numbers. n SDC-435 SERIES • NTSC MODEL • PAL MODEL SDC-435N SDC-435P SDC-435ND SDC-435PD SDC-435PH n MODEL DESCRIPTION • SDC-435XX _ _ • SIGNAL SYSTEM N → NTSC MODEL P → PAL MODEL • POWER SOURCE → AC 24V / DC 12V D → DC 12V H → AC 230V POWER SOURCE SIGNAL SYSTEM

User Guide 4 COLOR CCD CAMERA User Guide 5 Contents Features Excellent Sensitivity The built-in high sensitivity COLOR CCD produces a clear image even in 0.05Lux(COLOR), 0.0001Lux(SENS-UP) or lower illumination. Electrical Day&Night The camera automatically identifies when it is either day or night time and switched accordingly. During daylight the camera will switch to color to obtain excellent image clarity, while at night the camera will switch to monochrome to obtain improved picture definition. Motion Detection Since the camera detects motion without any additional external sensor, you can monitor activity more efficient. DIS (Digital Image Stabilizer) The DIS function compensates for any camera movement, to produce more stable pictures. Video/DC Drive Lens Support Communication You can select Video or DC Drive Lens from the menu. Coaxial communication methods are supported. - Protocol : Pelco Coaxitron Miscellaneous Functions HLC(High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM, SHARPNESS, MOTION DETECTION and PRIVACY functions are provided. OSD The camera’s OSD is complimented by 18 languages. - NTSC : Korean, English, French, Spanish, Japanese, Portuguese, Taiwanese - PAL : English, French, German, Spanish, Italian, Chinese, Russian, Czech, Polish, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese SSNR3 (Samsung Super Noise Reduction) Function The high-performance W-V DSP chip effectively removes low-light gain noise and afterimage to provide clear images even in dark environments. High Resolution By adopting a diagonal 6mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the camera produces clear picture quality with a horizontal resolution of 600 TV lines for color. • Features…………………………………………………………………………… 5 • Warnings & Cautions… ……………………………………………………… 6 • Precautions… …………………………………………………………………… 7 • Components and Accessories……………………………………………… 8 • Overview…………………………………………………………………………… 9 • Installation… …………………………………………………………………… 10 ■ LENS………………………………………………………………………………………… 10… ■ Connecting to the Monitor… ………………………………………………………… 12… ■ Using Coaxial Communications……………………………………………………… 13… ■ Connecting to the Power……………………………………………………………… 14 • Operating your Camera……………………………………………………… 15 ■ Menu Configuration……………………………………………………………………… 15… ■ Menu Setup… …………………………………………………………………………… 15… • LENS……………………………………………………………………………………… 16… • EXPOSURE……………………………………………………………………………… 17… • WHITE BALANCE… …………………………………………………………………… 19… • SSDR……………………………………………………………………………………… 20… • BACKLIGHT……………………………………………………………………………… 20… • SSNR3…………………………………………………………………………………… 22… • DAY/NIGHT……………………………………………………………………………… 23… • SPECIAL… ……………………………………………………………………………… 24… • EXIT… …………………………………………………………………………………… 28 • Troubleshooting………………………………………………………………… 29 • Specifications……………………………………………………………………… 30 SSDR (Samsung Super Dynamic Range) For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting, this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness.

User Guide 6 COLOR CCD CAMERA User Guide 7 Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products.The Eco mark represents Samsung Techwin’s will to create environment-friendly products, and indicates that the product satisfies the EU RoHS Directive. This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it carefully and use the product accordingly. Warnings & Cautions * For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as an aerial ladder while providing after-sales service shall be at your expense. * Separate the power plug during a thunder storm. * This product is only part of a surveillance system. Therefore, we can't compensate for material loss and personal injuries by robbery, fire, natural disaster or something like this type. Ignoring this information may result in material loss and serious personal injuries including death. Indicates “Never Allowed.” Ignoring this information may result in material loss and a slight injuries. Indicates “No Disassembling.” Warning/Attention/Special Mark Messages Precautions Do not install under extreme temperature conditions. Do not install in high humidity environment. Do not install under unstable lighting conditions. The lens is the most important component of the camera. Be careful not to smear it with fingerprints. Severe lighting changes or flickering may hinder normal camera operation. May lower image quality. Use only under temperature conditions between -10ºC and +50ºC. Provide good ventilation when using in high temperature conditions. Avoid touching the camera lens. Do not drop the camera or subject it to physical shock. May damage the CCD. May cause a product malfunction. Never keep the camera face to strong light directly.

User Guide 8 COLOR CCD CAMERA User Guide 9 Precautions • Exposure to the spotlights or objects reflecting bright light, smearing or blooming may occur. • Ensure that the power source complies with normal specifications before connecting it to the camera. Notes Components and Accessories 1 Ultra High Resolution Camera SDC-435 2 Auto iris lens connection plug 3 C-Mount adaptor 4 Instruction manual 1 2 3 4 Overview 1 5 2 3 4 1 CCD protection cap : Please cover the CCD SENSOR when not using it. 2 C-Mount lens adaptor : Please install this adapter when using a C-Mount Lens. 3 CS-Mount lens adaptor : Please remove the C-MOUNT lens adaptor and then attach it. 4 Back Focus clamp screw : Please loosen the clamp screw with a screwdriver before adjusting the Back Focal length. 5 Auto Iris Lens Connector Front View Side View Bottom View 6 Tripod Mounting Bracket Screw Hole Used to fix the camera on a bracket or tripod. The screw sizes for this hole are as follows: 1/4"-20 UNC (20 THREAD) L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard) You can separate the Tripod Mounting Bracket and install it on the top or bottom of the camera. Make sure to use the Tripod Mounting Bracket when fixing the camera to a bracket or tripod. Otherwise the camera may not be secure, or the internal circuitry of the camera may be damaged. 6 Do not expose the camera to rain or other types of liquids. Radioactivity exposure may damage the CCD. May cause a product malfunction.Wipe dry any liquids. Liquids may contain minerals that are corrosive to electronic components. Do not expose the camera to radioactivity.

User Guide 10 COLOR CCD CAMERA User Guide 11 Overview The lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts the auto iris lens and both C-and CS-mount lens. • To use the functions of this camera effectively it is recommended that a DC type Auto Iris lens is used. • Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints the picture quality suffers. Notes Installation Installation LENS When Using Auto Iris Lens When using a C-Mount lens 1. Strip the insulation of the auto iris lens cable 8mm from the end. 2. Strip the insulation of the core of the auto iris lens cable to expose a 2mm length. 8mm 2mm 3. Remove the cover of the auto iris lens connector plug and solder the lens cable to the connector pin of the plug. No.3 Pin No.1 Pin Connector Lens cable No.4 Pin No.2 Pin LENS Pin No. DC VIDEO No.1 Pin Damping - Red (power) No.2 Pin Damping + NC No.3 Pin Drive + White (video signal) No.4 Pin Drive - Black (GND) 4. Please replace the auto iris lens connection plug cover and take off the CCD protection cap, and then attach the auto iris lens to the camera by screwing it in clockwise. 5. Please insert the connection plug that is connected to the auto iris lens cable into the auto lens connector, which is located on the side of the camera. Please take off the CCD protection cap and attach the C-Mount lens to the camera by screwing it in clockwise. C-mount adaptor Rear View ❿ *High Voltage Type 7 Power lamp : Lights up when the correct power is supplied to the camera. 8 Function Setup Button •SETUP button : Displays the menu on the screen and uses enter sub menu. •Up&Down button : Used to move the cursor up or down in the menu screen. •Left&Right button : Used to move the cursor left or right in the menu screen. 9 Video output terminal : Sends video signal and connects to the video input terminal of the monitor. ❿ Power input terminal : Connects to the power appropriate to each model. 9 7 8

User Guide 12 COLOR CCD CAMERA User Guide 13 • Coaxial Communications System • OSD Control method 1. Please take off the CCD protection cap and C-mount adaptor. C-mount adaptor CCD protection cap CS-mount adaptor When using a CS-Mount lens • Please use the specified lens connection parts as shown in the picture below. The use of the wrong sized parts may cause damage to the inside of the camera or result in poor fitting. • Use of a lens which is too heavy affects the balance of the camera and may cause a malfunction. Please use a lens that weighs less than 450g. • Please select Av mode if possible when adjusting the automatic light control (ALC) of an auto lens. Use of PK mode may cause hunting. Notes C-mount lens : 10 mm or less CS-mount lens : 5 mm or less 2. Please attach the CS-Mount lens to the camera by screwing it in clockwise. Installation Connecting to the Monitor Please connect the video output terminal located on the back of the camera to the monitor. CCD Camera Monitor • The connection method varies depending on the type of monitor and accessories. Please refer to the user's manual for each instrument. • Please turn off the power when connecting. • Please select Hi-Z on the 75Ω/Hi-Z switch for the intermediate video TV set and select 75Ω for the Intermediate device as shown in the picture below. CCD Camera Intermediate End monitor Using Coaxial Communications Distance Recommended Cable Specification 300m 3C2V(RG-59/U) 450m 5C2V(RG-6/U) 600m 7C2V(RG-11/U) • Video Cable The camera's video output port is connected to the monitor with a BNC coaxial cable, shown below : If the distance between the camera and the monitor exceeds the recommended maximum, please use an auxiliary video amp. • It is recommended that pure copper coax cable is used and not copper coated steel, as this will cause issues with the communication over the coaxial cable. Notes CAMERA DVR CONTROLLER SET MENU/ENTER OSD KEY UP UP KEY JOYSTICK UP DOWN DOWN KEY JOYSTICK DOWN LEFT LEFT KEY JOYSTICK LEFT RIGHT RIGHT KEY JOYSTICK RIGHT DVD DVR • : BNC • ---- : RS-485

User Guide 14 COLOR CCD CAMERA User Guide 15 When the resistance value of copper wire is at [20ºC(68°F)] Copper wire size (AWG) #24(0.22㎟) #22(0.33㎟) #20(0.52㎟) #18(0.83㎟) Resistance (Ω / m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 • As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera. * Standard voltage for camera operation : DC 12V±10%, AC 24V±10%, AC 230V ±10% (SDC-435PH) * There may be some deviation in voltage drop depending on the type of wire and the manufacturer. Connecting to the Power Each model has a different power input specification. Please check the model type and standard power requirement before connecting to power. ※ This operating instruction has been written out as standard by F/W Version 1.0. • Use AC24V, 300mA adaptor or DC12V, 500mA for SDC-435N/P AC/DC Power Type • Use AC230V, 50Hz power source for SDC- 435PH. High Voltage Type (AC230V, 50Hz) • Use DC12V, 500mA for SDC-435ND/PD DC Power Type Installation Operating Your Camera MAIN MENU LENS ●DC ●VIDEO ●MANUAL EXPOSURE ●BRIGHTNESS ●SHUTTER ●AGC ●SENS-UP ●RETURN WHITE BALANCE ●ATW ●OUTDOOR ●INDOOR ●MANUAL ●AWC→SET SSDR ●OFF ●ON BACKLIGHT ●OFF ●BLC ●HLC SSNR3 ●OFF ●ON DAY/NIGHT ●COLOR ●B/W ●AUTO SPECIAL ●IMAGE ADJ. ●MONITOR ●CAM TITLE ●SYNC ●MOTION DET ●PRIVACY ●DIS ●LANGUAGE ●RETURN EXIT ●SAVE ●NOT SAVE ●RESET Menu Configuration UP button SET button LEFT button DOWN button RIGHT button Menu Setup You can set up functions using the 5 buttons on the rear of the camera. 1. Press the SET button. • Main setup menu is displayed on the monitor screen.

User Guide 16 COLOR CCD CAMERA User Guide 17 MAIN MENU 1.LENS DC 2.EXPOSURE 2. Select a desired function using the Up and Down buttons. • Place the cursor over a desired item. 3. Set up a selected item by using the Left and Right buttons. 4. To finish the setting, select ‘EXIT’ and press the SET button. MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 8.SPECIAL 9.EXIT SAVE Select the function using the UP or DOWN button. Change the status using the LEFT or RIGHT button. • An item with the icon also has sub menus. To select a sub menu, select an item with the icon and press the SET button. • An item with the - - - icon is unavailable due to function settings. Notes DC/Video : Select Auto Iris Lens You can adjust the minimum shutter and maximum value of ESC shutter mode when DC Lens mode is selected. Manual : Select Manual Lens Using this function, you can control the screen brightness. 1. When the SETUP menu screen is displayed, select‘LENS’by using the Up and Down buttons so that the arrow indicates‘LENS’. 2. Select the connected lens type by using the Left and Right buttons. LENS • When using VIDEO lens, adjust the lens VR explained below first and set the focus using 'FOCUS ADJ.' menu. • If color rolling occurs when using a DC lens, set Shutter to A.FLK. • Some lenses may not work properly, depending on the setting of the BRIGHTNESS LEVEL. • When Using a Video-Type Auto Iris Lens ❶ Adjust the ALC adjustment terminal on the lens appropriately. In general, set it to AV (Average). 2 It may not work properly depending on the installed lens. Set the Level VR of the lens to the optimal value. 3 Set AGC to OFF and adjust the Lens VR to an appropriate brightness. 4 Adjust the Lens VR, adjust the BRIGHTNESS, and then check if the screen brightness changes properly. Otherwise, adjust the Lens VR again. Notes Operating Your Camera - Level (VIDEO) : Adjusts the level of video iris signals; the higher the level is, the brighter the video looks. - FOCUS ADJ. (DC, VIDEO) : To adjust the DC and VIDEO lens focus correctly, you must activate the Focus Settings mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and then deactivate the settings mode. (The VIDEO lens requires an extra step: go to the sub menu of the Focus Settings mode and change the shutter speed to adjust the lens brightness.) - IRIS SPEED (DC) : Adjusts the Iris control speed of the DC lens. If the control speed is too slow or fast, please use this menu to adjust the speed. 3. Each Lens mode has sub menu items as listed below. - Brightness (DC, Manual) : Adjusts the video brightness. MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW EXPOSURE 1. When the SETUP menu screen is displayed, select‘EXPOSURE’by using the Up and Down buttons so that the arrow indicates‘EXPOSURE’. 2. Select a desired mode using the Up and Down buttons. EXPOSURE SETUP 1.BRIGHTNESS 25 2.SHUTTER ESC 3.AGC HIGH 4.SENS-UP OFF 5.RETURN

User Guide 18 COLOR CCD CAMERA User Guide 19 Operating Your Camera • When you use a DC lens, set the shutter mode to A.FLK if color rolling occurs. • When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the picture may become unstable if the camera faces a bright fluorescent light. Therefore, take care when choosing the installation position. • When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled. Notes AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but the higher the noise. - OFF : Deactivates the AGC function. - LOW : Allows automatic gain control from 5.3dB to 32dB. - HIGH : Allows automatic gain control from 5.3dB to 37dB. SENS-UP : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated. - OFF : Deactivates the SENS-UP function. - AUTO : Activates the SENS-UP function. • If you press the SET button in ‘AUTO’ mode, You can adjust brightness by increasing or decreasing the shutter speed. (x2 ~ x512) • Note that the higher the zoom level, the brighter the screen, but the more likely it is that an after-image will appear. • Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the zoom level is increased, this is normal. Notes RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu. Use the White Balance function to adjust the screen color. 1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Up and Down buttons so that the arrow indicates ‘White Bal.’ . 2. Select a desired mode using the Up and Down buttons. White Balance (White Bal.) SHUTTER : You can select either auto or manual shutter. - --- : Shutter speed is fixed at 1/60sec(1/50sec). - A.FLK : Select this when you experience picture flicker, which can happen when there is a clash with the frequency of the installed lighting. - ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject. - MANUAL : You can control shutter speed manually. (1/60 ~ 1/120,000) ※ Select one of the following 5 modes, as appropriate for your purpose. ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K. OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K. (sodium light inclusion) INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K. MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that switch to MANUAL mode, fine- tune the White Balance and then press the SET button. AWC→SET : To find the optimal luminance level for the current environment, point the camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, readjust it. MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF • White Balance may not work properly under the following conditions. In this case select the AWC mode. ❶ When the color temperature of the environment surrounding the subject is out of the control range (e.g. clear sky or sunset). 2 When the ambient illumination of the subject is dim. 3 If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable. Notes

User Guide 20 COLOR CCD CAMERA User Guide 21 SSDR OFF Operating Your Camera BACKLIGHT Unlike conventional cameras, the SDC-435 is designed so that it delivers a distinctive subject and background at the same time, even when the subject is in backlight, by adopting a proprietary W-V DSP chip. 1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Up and Down buttons so that the arrow indicates ‘BACKLIGHT’. 2. Select a desired mode using the Left and Right buttons depending on the camera purpose. BLC : Enables a user to select a desired area on a picture and view that area more clearly. MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF HLC (High Light Compensation) :  If the scene contains extremely bright light areas such as; from car headlight, the light can mask out much of the on-screen detail. - LEVEL : Adjust level of the HLC function. - LIMIT : Enable to change the operating condition. - MASK COLOR/TONE : Change the color / brightness of the masking area. (Black, Red, Blue, Cyan, Magenta) - TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced. OFF : Not being used MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF SSDR (Samsung Super Dynamic Range) SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas. 1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the Up and Down buttons so that the arrow indicates ‘SSDR’. 2. Use the Left/Right buttons to change the SSDR level in the sub menu according to the contrast between bright and dark areas. SSDR ON 3. Select a desired mode using the Left and Right buttons and press the SET button. Select ‘BLC’ to adjust the area to be enhanced then adjust the level. HLC : Enable the user to change the level, limit, mask color/tone and area.

User Guide 22 COLOR CCD CAMERA User Guide 23 Operating Your Camera • Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance. • When dark, the HLC is only activated when a bright light exceeding a specific size.in NIGHT ONLY mode. • The HLC is not activated in day light or when bright light is not present at night.in NIGHT ONLY mode. Notes This function reduces the background noise in a low luminance environment. 1. When the SETUP menu screen is displayed, select ‘SSNR’ by using the Up and Down buttons so that the arrow indicates ‘SSNR’ . 2. Select a desired mode using the Left and Right buttons. OFF : Deactivates SSNR. Noise is not reduced. ON : Activates SSNR so that noise is reduced. SSNR3 MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 3. Set the SSNR mode to ‘ON’ and press the SET button. Then you can adjust the noise reduction level. • You cannot set the SSNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’. • When adjusting the noise reduction level in the SSNR mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image. Notes You can display pictures in color or black and white. 1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and Down buttons so that the arrow indicates ‘DAY/NIGHT’. DAY/NIGHT MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 8.SPECIAL 2. Select a desired mode using the Left and Right buttons according to the picture display you want. COLOR : The picture is always displayed in color. B/W : The picture is always displayed in black and white. You can turn on or off the burst signal on B/W mode. AUTO : The mode is switched to ’Color‘ in a normal environment, but switches to ’B/W‘ mode when ambient illumination is low. To set up the switching time for AUTO mode, press the SET button. You can turn on or off the burst signal on B/W mode. - DWELL TIME : You can select the duration time about changing the day/night mode. … →5s, 7s, 10s, 15s, 20s, 30s, 40, 60s • When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching between Color and Black & White may not occur. • When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR' mode and 'AUTO' mode can not be selected. Notes

User Guide 24 COLOR CCD CAMERA User Guide 25 Operating Your Camera • V-REV : You can flip the picture vertically on the screen. • H-REV : You can flip the picture horizontally on the screen. • D-ZOOM : You can use a digital zoom of x1 ~ x16. • FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) • SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture. • RETURN : Select this to save the settings for the IMAGE ADJ. menu and to return to the SETUP menu. 1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Up and Down buttons so that the arrow indicates ‘SPECIAL’. SPECIAL MAIN MENU 1.LENS DC 2.EXPOSURE 3.WHITE BAL ATW 4.SSDR OFF 5.BACKLIGHT OFF 6.SSNR3 ON 7.DAY/NIGHT COLOR 8.SPECIAL 9.EXIT SAVE IMAGE SETUP 1. V-REV OFF 2. H-REV OFF 3. D-ZOOM OFF 4. FONT COLOR WHITE 5. SHARPNESS ON 6. RETURN IMAGE ADJ. :  1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Up and Down buttons so that the arrow indicates ’IMAGE ADJ‘. SPECIAL 1. IMAGE ADJ 2. MONITOR LCD 3. CAM TITLE OFF 4. SYNS INT 5. MOTION DET OFF 6. PRIVACY OFF 7. DIS OFF 8. LANGUAGE ENGLISH 9. RETURN 2. Select a desired mode using the Up and Down buttons. • When the V-REV or H-REV mode is enabled, the text on the screen does not flip. • If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear. Notes Monitor : Please change the settings value of video appropriate to your monitor. - LCD : Please select this menu item when using an LCD monitor. - CRT : Please select this menu item when using a CRT monitor. - USER : Please use this menu item when using a monitor other than standard ones. You can change the gamma, PED level, and color gain in the sub menus. 2) Select a desired mode using the Up and Down buttons.

User Guide 26 COLOR CCD CAMERA User Guide 27 Operating Your Camera CAM TITLE : If you enter a title, the title will appear on the monitor.  1) If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow indicates ‘CAM TITLE’. 2) Set it to ‘ON’ by using the Left and Right buttons. 5) Enter a title, move the cursor to ‘POS’ and press the SET button. The entered title appears on the screen. Select the position to display the title on the screen by using the 4 direction buttons and press the SET button. When the position is determined, select ‘END’ and press the SET button to return to the SPECIAL menu. MOTION DET :  This product has a feature that allows you to observe movement of objects in 8 different areas on the screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected. you can monitor activity more efficient. FRONT DOOR 1) When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the arrow indicates‘MOTION DET’. 2) Set up the mode using the 4 direction buttons. - SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement. - AREA MODE : Determines whether to use the MD area selected in SENSITIVITY. - SEL POS : Determines which of the 4 vertices of each MD area is to be used. - YPOS : Determines the coordinate of the vertical axis for SEL POS. - XPOS : Determines the coordinate of the horizontal axis for SEL POS. - FILL→SET : Fills in a selected MD area. The color of filling is sequentially selected as brown, orange, blue, cyan, green, yellow, magenta and red. - RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu. 3) Press the SET button. 4) Use the 4 direction buttons to move to a desired letter and select the letter by pressing the SET button. Repeat this to enter multiple letters. You can enter up to 15 letters.  CAMERA TITLE SETUP A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z - . 0 1 2 3 4 5 6 7 8 9 ←→C L R P O S E N D • When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one. • Only English is available in this mode. • If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the SET button. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the SET button. Notes • When using AC power at 60Hz frequency, you can use the L/L type synchronization. • When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode. Notes SYNC : In areas where the supply is at 60Hz, you can synchronize the output phase of multiple cameras using the power synchronization function (Line- Lock) without using a synchronization signal generator. - INT : Internal Synchronization Type - L/L : Power Synchronization Type, Line-lock • Press the Function Setup switch. • You can select a desired phase from 0 to 359 when select 'phase'. PRIVACY : Mask an area you want to hide on the screen. PRIVACY AREA SETUP 1. AREA AREA1 2. MODE OFF 3. MASK COLOR GREEN 4. MASK TONE 1 5. TOP 39 6. BOTTOM 79 7. LEFT 12 8. RIGHT 51 9. RETURN

User Guide 28 COLOR CCD CAMERA User Guide 29 Operating Your Camera - AREA SEL : You can select up to 12 PRIVACY areas. - MODE : Determines whether to use the area selected in the AREA SEL. - MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray. - MASK TONE : Adjust the brightness of MASK COLOR. - TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area. - RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu. Select a desired EXIT mode using the Left and Right buttons depending on the camera purpose. - SAVE : Save the current settings and exit the MAIN SETUP menu. - NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu. - RESET : Resets the camera settings to the factory defaults. Language and Monitor settings are not initialized. LANGUAGE : You can select the menu language according to your requirements. RETURN : Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu. • As the DIS function uses the digital zoom the camera's resolution will decrease. • DIS doesn’t operate when background illumination is too low. • DIS doesn’t operate when object pattern is monotonic as like sky or white wall. Notes DIS (Digital Image Stabilizer) : This function mitigates any picture movement due to external factors such as wind. EXIT Troubleshooting If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. ● Nothing appears on the screen. ▶ Check that the power cord and line connectionbetween the camera and monitor are fixed properly. ▶ Check the type of lens. ▶ Check that the lens type is VIDEO lens or DC lens. ● The image on the screen is dim. ▶ Is lens stained with dirt? Clean your lens with soft, clean cloth. ▶ Set the monitor to proper condition. ▶ If the camera is exposed to too strong light, change the camera position. ● The image on the screen is dark. ▶ Adjust the contrast feature of the monitor. ▶ If you have an intermediate device, set the 75Ω / Hi-z properly. ● The camera is not working properly, and the surface of the camera is hot. ▶ Check that you have properly connected the camera to an appropriate power source. ● The SENS-UP function does not work. ▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’. ▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’. ● The Motion Detection function does not work. ▶ Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’. ● Color is not correct. ▶ Check the setting of WHITE BAL SETUP menu . ● The screen flickers continually. ▶ Check that direction of camera turns toward the Sun. ● When coaxial communication is not available: ▶ Make sure that the camera and monitor are installed within the recommended distance. ▶ Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded. 1) When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the arrow indicates ‘PRIVACY’. 2) Set up the mode using the 4 direction buttons.

User Guide 30 COLOR CCD CAMERA User Guide 31 SDC-435ND SDC-435N SDC-435PD SDC-435P SDC-435PH ELECTRICAL Input Voltage DC 12V AC 24V / DC 12V DC 12V AC 24V / DC 12V AC 230V, 50Hz Power Consumption Max 2.5W Max 3.5W Max 2.5W Max 3.5W Max 4.0W VIDEO Imaging Device 1/3 inch, Diagonal 6mm Super HAD CCD Total Pixels 811(H) x 508(V) 795(H) x 596(V) Effective Pixels 768(H) x 494(V) 752(H) x 582(V) Scanning System 2:1 Interlace Synchronization Internal Only Internal /LineLock Internal Only Internal / Line-Lock Frequency H : 15.734KHz V:59.54Hz H: 15.625KHz V: 50.00Hz Horizontal Resolution 600TVL Min. Illumination 0.05 Lux(50IRE, No SENS-UP) / 0.0001Lux (SENS-UP x512) @F1.2 S/N (Y Signal) 52dB (Weight Off, AGC Off) Video Output CVBS : 1.0Vp-p, 75Ω composite OPERATIONAL IRIS Adustment DC / VIDEO Electronic Shutter Speed 1/60 ~ 1/120K sec 1/50 ~ 1/120K sec On Screen Display NTSC : 7 Languages, PAL : 15 Languages SSDR On / Off (Level adjustable) Backlight Compensation BLC / HLC / OFF Day & Night COLOR / BW / AUTO (Electric) Gain Control Low / High / Off White Balance ATW / OUTDOOR / INDOOR / MANUAL / AWC (1,700°K ~ 11,000°K) SENS-UP (frame Integration) Auto /Off (Selectable x2 ~ x512) Motion Detection On / Off (8 Programmable zones) Privacy Masking On / Off (12 Programmable zones) 3D Noise Filter (SSNRIII) On / Off (Level adjustable) Digital Zoom On / Off (x1 ~ x16) Digital Image Stabilization(DIS) On / Off Camera Title Off / On (Displayed 15 Characters) Sharpness On / Off (Level adjustable) Flip / Mirror On / Off Communication Coaxial (Protocol : Pelco Coaxitron) ENVIRONMENTAL Operating Temp/Humid -10°C ~ +50°C / 30% ~ 80% RH Storage Temp/Humid -20°C ~ +60°C / 20% ~ 90% RH MECHANICAL Lens Mount C / CS Mount Back Focus Adjustment Manual Dimension 58(W) x 52(H) x 121(D)mm Weight 290g 310g 290g 310g 510g Specifications DECLARATION OF CONFORMITY Application of Council Directive(s) 89 / 336 / EEC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-716 European Representative Name European Representative Address Equipment Type/Environment CCTV Camera Model Name SDC-435P, SDC-435PH, SDC-435PD Beginning Serial NO. C61S4010007 Year of Manufacture 2009.06.01 Conformance to EN 50081-1 : 1992 EMC-Directive 89/336 EEC and 92/31/EEC EN 50130-4 : 1996 We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s). Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe Signature Signature Full Name BONJENG GU Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA Place Date 2009.06.01 Date ※ The specification for this product may change without prior notice for product improvement.

VAN 09. 10 www.samsungtechwin.com www.samsungcctv.com • SAMSUNG TECHWIN CO., LTD. 145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703 TEL : +82-31-740-8151~8 FAX : +82-31-740-8145 • SAMSUNG TECHWIN EUROPE CO., LTD. Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS TEL : +44-1932-45-5300 FAX : +44-1932-45-5325 • SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com SALES NETWORK