Samsung 191T - SyncMaster 19" LCD Monitor Serivce Manual

1. Always unplug the unit’s AC power cord from the AC power source and disconnect the DC Power Jack before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a test component in parallel with an electrolytic capacitor. 2. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 3. After ...

GH19BS SNA C373 2409-001043 C-ORGANIC 47UF,20%,6.3V,WT,TP,6.3X6.8,2.5 C622 2409-001043 C-ORGANIC 47UF,20%,6.3V,WT,TP,6.3X6.8,2.5 CIS 0201-001223 ADHESIVE-TS HT-130S,RED,700+/- 50,- SNA CIS 0202-001044 SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- SNA CIS 0202-001046 SOLDER-WIRE FLUX CF-110VH-2A,-,-,-,- SNA CIS 0202-001162 SOLDER-CREAM RMA-20-21L,S63,-,SN63/PB36.6/AG0.4,FLUX9.5% SNA CIS 0202-001222 SOLDER-WIRE FLUX RS-107,RS60-1.2AA,D1.2,SN60/PB40,- SNA CIS 0204-001095 THINNER #4520,-,-,- SNA CIS 6011-001445 BOLT-SOCKET 4-40 UNC,L7,NI PLT,BRASS,HEX SOCKET SNA CIS BN39-0 ...

GH19B* 9-1 B12 YUV7 B13 C13 YUV3 YUV2 A14 YUV1 B14 YUV0 gm5020 01H IC301 K1 VSYNC A12 VCLK J4 TCLK RXC- D6 RXC C6 RX@- D10 C10 RX2 RX1- D9 C9 YUV6 C12 A13 YUV5 YUV4 RX0 REXT B10 T1 RESETn E2 RED- RED E1 J3 PLLVDD_3.3_7 PLLVDD_3.3_6 J1 H1 PLLVDD_3.3_5 PLLVDD_3.3_4 G3 G1 C14 XTAL H4 PLLVDD_3.3_2 F4 F2 PLLVDD_3.3_1 PLLGND_7 K3 J2 PLLGND_6 PLLGND_5 H3 H2 PLLGND_4 PLLGND_3 G4 G2 PLLGND_2 PLLGND_1 F3 RX1 RX0- D8 C8 D1 GRN- GRN D2 GPIO7 G19 K2 NC5 F1 NC4 NC3 B5 A5 NC2 NC1 A1 R3 IRQn IRQINn R4 PLLVDD_3.3_3 M1 GPIO3 M2 M3 GPIO2 GPIO1 M4 HSYNC L2 HFSn P2 HDATA3 P3 P4 HDATA2 HDATA1 R1 R2 HDATA0 P1 HCLK V ...

GH19B* 9-1 B12 YUV7 B13 C13 YUV3 YUV2 A14 YUV1 B14 YUV0 gm5020 01H IC301 K1 VSYNC A12 VCLK J4 TCLK RXC- D6 RXC C6 RX@- D10 C10 RX2 RX1- D9 C9 YUV6 C12 A13 YUV5 YUV4 RX0 REXT B10 T1 RESETn E2 RED- RED E1 J3 PLLVDD_3.3_7 PLLVDD_3.3_6 J1 H1 PLLVDD_3.3_5 PLLVDD_3.3_4 G3 G1 C14 XTAL H4 PLLVDD_3.3_2 F4 F2 PLLVDD_3.3_1 PLLGND_7 K3 J2 PLLGND_6 PLLGND_5 H3 H2 PLLGND_4 PLLGND_3 G4 G2 PLLGND_2 PLLGND_1 F3 RX1 RX0- D8 C8 D1 GRN- GRN D2 GPIO7 G19 K2 NC5 F1 NC4 NC3 B5 A5 NC2 NC1 A1 R3 IRQn IRQINn R4 PLLVDD_3.3_3 M1 GPIO3 M2 M3 GPIO2 GPIO1 M4 HSYNC L2 HFSn P2 HDATA3 P3 P4 HDATA2 HDATA1 R1 R2 HDATA0 P1 HCLK V ...

3-2 GH19B* CONFIDENTIAL 4. Put the jig into the gap (between the right side of the panel the and Front Cover) and tilt up Front Cover until the snap opens. 5. Put the jig into the gap (between the right side of the panel the and Front Cover) and tilt up Front Cover until the snap opens. 6. After pushing the right bottom of the panel with jig. 7. Pull up the Rear Cover until it opens fully. 3-2 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. ...