Samsung SNB-7002 Operation & User’s Manual

Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice. ™ Design and specifications are subject to change without prior notice. ™ The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. Network Camera User Manual

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/ accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lighting storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. overview

THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions. CAUTION CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed. CAUTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. The BNC Out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes. If you keep the BNC cable connected, a risk of lightening may cause damage or malfunction to the product. Please use the input power with just one camera and other devices must not be connected.

Do not place this apparatus on an uneven surface. Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. Do not place this apparatus near conductive material. Do not attempt to service this apparatus yourself. Do not place a glass of water on the product. Do not install near any magnetic sources. Do not block any ventilation openings. Do not place heavy items on the product. User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below. Reference : In case of providing information for helping of product’s usages Notice : If there’s any possibility to occur any damages for the goods and human caused by not following the instruction  Please read this manual for the safety before using of goods and keep it in the safe place.

9 Product Features 10 Recomended PC Specifications 10 Recomended SD/SDHC Memory Card Specifications 11 What’s Included 14 At a Glance (SNB-7002) 18 At a Glance (SND-7082) 22 At a Glance (SND-7082F) 25 At a Glance (SNV-7082) INSTALLATION & CONNECTION 28 28 Mounting the Lens (SNB-7002) 30 Installation (SND-7082) 32 Installation (SND-7082F) 34 Installation (SNV-7082) 39 Inserting/Removing a SD Memory Card 43 Memory Card Information (Not Included) 44 Connecting with other Device NETWORK CONNECTION AND SETUP 50 50 Connecting the Camera Directly to Local Area Networking 51 Connecting the Camera Directly to a DHCP Based DSL/Cable Modem 52 Connecting the Camera Directly to a PPPoE Modem 53 Connecting the Camera to a Broadband Router with the PPPoE/Cable Modem 54 Buttons used in IP Installer 55 Static IP Setup 59 Dynamic IP Setup 60 Port Range Forward (Port Mapping) Setup 62 Connecting to the Camera from a Shared Local PC 62 Connecting to the Camera from a Remote PC via the Internet

91 Network Setup 100 Event Setup 116 System Setup APPENDIX 123 123 Specification 129 Product Overview 133 Troubleshooting 135 Open Source Announcement WEB VIEWER 63 63 Connecting to the Camera 64 Login 65 Installing Silverlight Runtime 69 Installing STW WebViewer Plugin 70 Using the Live Screen 72 Search and play by event 73 Search and play by time

• Multi-Streaming This network camera can display videos in different resolutions and qualities simultaneously using different CODECs. • Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment. • Alarm If an event occurs, the event-related video will be transferred to the FTP/email specified by the user or saved to the SD memory, or the event signal will be sent to the Alarm Out port. • Tampering Detection Detects tempering attempts on video monitoring. • Motion Detection Detects motion from the camera’s video input. • Intelligent Video Analysis Analyzes video to detect logical events of specified conditions from the camera’s video input. • Face Detection Detects faces from the camera’s video input. • Smart Codec Adaptively applies codecs for a portion of the camera’s field of view to improve the quality of such area specified by user. • Audio Detection Detects sound louder than a certain level specified by user. • Auto Detection of Disconnected Network Detects network disconnection before triggering an event. • ONVIF Compliance This product supports ONVIF. For more information, refer to www.onvif.org.

• CPU : Intel Core 2 Duo 2.4GHz or higher • Operating System : Windows XP, VISTA, 7, Mac OS • Resolution : 1280X1024 pixels or higher (32 bit color) • RAM : 2GB or higher • Web Browser : Internet Explorer 7 or Higher, Firefox 9 or Higher, Chrome 15 or Higher, Safari 5.1 or Higher Neither a beta test version unlike the version released in the company website nor the developer version will be supported. It is recommended to connect to IPv6 in Windows 7. • Video Memory : 256MB or higher J If the driver of the video graphic adapter is not installed properly or is not the latest version, the video may not be played properly. For a multi-monitoring system involving at least 2 monitors, the playback performance can be deteriorated depending on the system. RECOMENDED SD/SDHC MEMORY CARD SPECIFICATIONS • 4GB ~ 32GB • It is recommended to use memory cards of at least class 6 speed.

Appearance Item Name Quantity Description Model Name Camera 1 SNB-7002 or SND-7082 or SND-7082F or SNV-7082 UNLOCK 1 1 1 Instruction book, Installer S/W CD, CMS S/W DVD 2 SNB-7002/ SND-7082/ SND-7082F/ SNV-7082 Quick Guide (Optional) 1 Cable for the testing monitor 1 Used to test the camera connection to a portable display device

Auto Iris Lens Connector 1 Used to install the C Mount camera lens SNB-7002 Camera Holder (Mount) 1 Used to install the camera holder Camera Holder (Mount) Screws 2 Used to install the mount 6-position Terminal Block 1 Used for alarm in/out terminals 5-position Terminal Block 1 Used for alarm in/out terminals SND-7082/ SND-7082F/ SNV-7082 Iron Screw 3 Used for fixing to an iron plate SND-7082/ SND-7082F Template 1 Product installation guide SND-7082F/ SNV-7082 Jack Modular 1 LAN cable gender Dustproof Plate 1 Prevents dust ingress into the wiring connection part. SND-7082

SND-7082F Bracket Safety 1 Safety Bracket ASSY-Tapping Screw 4 Used for installation on the wall or ceiling SNV-7082 L Wrench 1 Used to remove/ fix the dome cover Plastic Anchor 4 For fixing a screw, Inserted in a hole (reinforced anchoring force) Machine Screws 4 Used for assembling the dome case when installing the product on the pipe, wall mount, etc. or blocking a hole. Lens Options (not included) CS/C Lens Optional lens to be inserted in a camera SNB-7002

Front Side Item Description  Camera Holder (Mount) Holes Used when you mount the camera onto the bracket by fixing the camera holder (mount) adaptor with the bracket. b Mounting Bracket Screw Hole Used to fix the camera on a bracket or mounting bracket. The screw size : use this screw to fix the mounting bracket. 1/4" - 20UNC (20THREAD) L : 4.5mm±0.2mm (ISO Standard) or 0.197" (ASA Standard)  b c 

(Optional) Installed on the lens adaptor.  Auto Iris Lens Connector Used to supply power and output signal to control the iris of the lens. M Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol. Mounting Bracket is not included. For more information to use mounting bracket, refer to the product’s documentation.

Compartment Compartment for the SD memory card. b Audio terminal AUDIO OUT Used to connect to speakers. AUDIO IN Used to connect to a microphone. c SD, Power Indicators SD ON : A memory card is inserted and operates normally. Flashing : Failed to record, insufficient space, or inserted abnormally. OFF : Camera is off, camera is restarting, memory card is not in place, or when record is off. POWER ON : While the power is on OFF : If the power is off  b c      

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network. Focus Adjustment Button The button adjusts the focus of image automatically.  Power Port Used to plug the power cable.  Lightning protective grounding port Used to discharge the lightning current safely outside in order to protect the camera.  Network Port Used to connect the PoE or Ethernet cable for network connection.  Alarm I/O Port ALARM IN Used to connect the alarm input signal. ALARM OUT Used to connect the alarm output signal. GND Used for earth-grounding.  Test Monitor Out Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

Appearance Item Description  Top cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body. UNLOCK  b c   

Used to plug the power cable.  Test Monitor Out Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video. Network Port Used to connect the PoE or Ethernet cable for network connection.  Audio In Jack Used to connect to a microphone.  Audio Out Jack Used to connect to speakers.

b Alarm I/O Port ALARM IN Used to connect the alarm input signal. ALARM OUT Used to connect the alarm output signal. GND Used for earth-grounding. c Reset Button The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.  Test Monitor Out Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video. Focus Adjustment Button The button adjusts the focus of image automatically.  SD Memory Card Compartment Compartment for the SD memory card.  Lock Release Lever Press the levers on both ends to separate camera module from the body.  Bracket Used to install the camera on the wall or ceiling with the screws.  Wiring Cover If you drill a hole in the wiring cover for wiring, remove the cover and attach the provided dustproof plate to it, and arrange the cables through the plate.  Release Lock If you want to remove the bracket from the main unit or remove the camera from the bracket, push this out and turn the main unit in the direction.

Appearance Item Description  Top cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body. c Power Port Used to plug the power cable.  Test Monitor Out Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video. Network Port Used to connect the PoE or Ethernet cable for network connection.  Audio In Jack Used to connect to a microphone.  Audio Out Jack Used to connect to speakers. c     b

Used to connect the PoE or Ethernet cable for network connection. b Alarm I/O Port ALARM IN Used to connect the alarm input signal. ALARM OUT Used to connect the alarm output signal. GND Used for earth-grounding. c Test Monitor Out Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.  Reset Button The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.  b c 

Press the levers on both ends to separate camera module from the body.  Lens Lens for the camera.  Focus Adjustment Button The button adjusts the focus of image automatically.  SD Memory Card Compartment Compartment for the SD memory card.   

Appearance Item Description  Top cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body. c Power Port Used to plug the power cable.  Test Monitor Out Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video. Network Port Used to connect the PoE or Ethernet cable for network connection.  Audio In Jack Used to connect to a microphone.  Audio Out Jack Used to connect to speakers.  b c   

Used to connect the PoE or Ethernet cable for network connection. b Alarm I/O Port ALARM IN Used to connect the alarm input signal. ALARM OUT Used to connect the alarm output signal. GND Used for earth-grounding. c Test Monitor Out Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.  Reset Button The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.  b c 

Press the levers on both ends to separate camera module from the body.  Lens Lens for the camera.  Focus Adjustment Button The button adjusts the focus of image automatically.  SD Memory Card Compartment Compartment for the SD memory card.  Release Lock If you want to remove the bracket from the main unit or remove the camera from the bracket, push this out and turn the main unit in the direction.    

installation & connection MOUNTING THE LENS (SNB-7002) Disconnect the power before proceeding. M The C lens and CS lens are not included in the product package. It is recommended that megapixel lens are use on this camera to optimise performance. Mounting the CS lens on a camera Turn the optional CS lens clockwise to insert it. Mounting the C lens on a camera Turn the C mount adaptor clockwise to insert it and do the same with the C lens. CS Lens C Lens

Connecting the Auto Iris Lens connector Insert the lens connector into the corresponding hole of the camera. Focusing Turn the lens left or right to control the zoom and focus the lens so that you can view a clear, sharp object.

30_ installation & connection Precautions before installation Ensure you read out the following instructions before installing the camera: • When installing on a ceiling or wall, desired spot must be capable of supporting at least 5 times of the camera’s weight. • Stuck-in or peeled-off cables can cause damage to the product or a fire. • For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case. INSTALLATION (SND-7082) Disassembling 1. Take the camera body with one hand and take the top cover with the other hand. Then, turn the cover counter clockwise to remove it. 2. Press the levers on both ends to separate camera module from the body. UNLOCK Top cover Camera Body

3. Hold down the lock lever in the outer direction as shown and turn the camera body in the direction (counter clockwise) to remove the bracket from the body. If it fails, take the bottom hole of the bracket and turn the bracket in the direction (clockwise) to remove it. Installation 1. Use the provided screws (x3) to fix the bracket to a desired position on the ceiling or wall. Ensure that the label on the bracket faces the direction for camera monitoring. 2. Arrange the cables through the bracket to the ceiling or wall. If you drill a hole in the ceiling cover for wiring, press hard to remove the cover and attach the dust-proof plate to it, and arrange the cables through the plate. If you intend to arrange the cables without drilling a hole, use the empty area opposite to the label side for the wiring purpose. 3. Mount the camera body onto the bracket. Align the marking hole of the camera body with the label of the bracket, and turn the body in the direction. 4. Assemble the camera module to the body. 5. Refer to “Adjusting the monitoring direction for the camera” to adjust the lens in a desired direction. (page 38) 6. Close the top cover. Fit the top cover into the fixing tips of the camera body and turn the cover clockwise. Bracket Camera Body Wiring Cover UNLOCK

32_ installation & connection INSTALLATION (SND-7082F) Disassembling 1. Take the camera body with one hand and take the top cover with the other hand. Then, turn the cover counter clockwise to remove it. Installation 1. Use the provided template to drill one hole for the camera, and one for the screw (5 mm in diameter, at least 35 mm in depth), and insert the plastic anchor (HUR 5) to the end of the screw hole. 2. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the camera. 3. Insert the camera body into the hole so that it fits to the camera hole, and fix the body using the ASSY tapping screws (TH M4xL30). (x3) 4. Refer to “Adjusting the monitoring direction for the camera” to adjust the lens in a desired direction. (page 38) 5. Close the top cover. Fit the top cover into the fixing tips of the camera body and turn the cover clockwise. Camera Body Top cover

To add an alarm cable (not included) 1. For this, first you should remove the top cover from the housing. 2. Pull out the protruding rubber bar as shown. 3. This will reveal a hole in the place of the rubber bar, through which you insert the cable, and connect it to the alarm terminal on the PCB. 4. Connect and arrange the necessary cables (power, video, etc) lest that they should be damaged or caught while installing the camera. Then, install the camera assembly in the reverse order of the disassembly. 5. Refer to “Adjusting the monitoring direction for the camera” to adjust the lens in a desired direction. (page 38) 6. Close the top cover.

34_ installation & connection INSTALLATION (SNV-7082) Disassembling 1. With the provided L-shaped wrench, loosen 3 bolts on the top cover counter clockwise to remove the cover. 2. Loosen 3 screws on the camera body counter clockwise, and push down the left/right LOCKER lever (in the arrow direction) to release the lock. Then, remove the camera from the case. LOCKER Lever Top cover Bolts Camera Case Camera Body

Installing on the ceiling directly 1. Remove the top cover from the case by referring to the “Disassembling” section. (page 34) 2. Drill a hole (diameter: 5mm, depth: min 35mm) in a desired position of the case bottom and insert the provided plastic anchor (HUD 5) to the end. 3. Fit the bottom hole to the anchor hole and insert and fix the ASSY taping screw (TH M4×L30). When assembling the camera case to a junction box, select appropriate screw holes on the case bottom for installation. 4. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the camera. 5. Install the camera body in the reverse order of “Disassembling”. (page 34) 6. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera" section. (page 38) 7. Close the top cover. To ensure waterproofing, tight up the fixing bolts using the L-wrench. Ceiling mount 1. Remove the top cover from the case by referring to the “Disassembling” section. (page 34) 2. Use the provided template to drill one hole for the camera, and one for the screw (5 mm in diameter, at least 35 mm in depth), and insert the plastic anchor (HUR 5) to the end of the screw hole. 3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the camera. CAMERA FRONT

36_ installation & connection 4. Loosen and remove the case-fixing screws on the camera unit. (x3) 5. Insert the camera unit into the hole so that it fits to the camera hole, and fix the unit using the ASSY tapping screws (TH M4×L30). (x3) 6. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 38) 7. Close the top cover. To ensure waterproofing, tight up the fixing bolts using the L-wrench. Attaching to the unbundled adapter Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience. 1. Remove the top cover from the case by referring to the “Disassembling” section. (page 34) 2. Use the provided machine screw to fix the camera case to the unbundled adapter. 3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the camera. 4. Install the camera body in the reverse order of “Disassembling”. (page 34) 5. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 38) 6. Close the top cover. To ensure waterproofing, tight up the fixing bolts using the L-wrench. Optional Accessories for Installation For your easier installation, you can purchase appropriate optional accessories available. 1. WALL MOUNT ADAPTOR(SBP-300WM or SBP-300WM1)/HANGING MOUNT (SBP-300HM3) This adaptor is used when installing the dome camera onto a wall.

2. CEILING MOUNT ADAPTOR(SBP-300CM)/ HANGING MOUNT(SBP-300HM3) This adaptor is used when installing the dome camera on a concrete ceiling. 3. POLE MOUNT ADAPTOR(SBP-300PM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on a pole whose diameter is bigger than 80mm. 4. CORNER MOUNT ADAPTOR (SBP-300KM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on the corner of wall joint.

38_ installation & connection Adjusting the monitoring direction for the camera (SND-7082/ SND-7082F/SNV-7082) Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation. - The effective range of pan is a total of 355 degrees. - The effective range of rotation is a total of 355 degrees. - The effective range of tilt is a total of 90 degrees. J In some angles, the top cover may cause cutting some part of the monitoring object. Do not rotate the focus/zoom lens by force after removing the cover front. Otherwise, it may cause an incorrect focus due to a motor failure. Methods of adjustment 1. After installing the camera, adjust the panning angle in consideration of the monitoring direction. When tilting the camera, you should adjust the horizontal angle lest that the image be displayed reversely. 2. Adjust the rotation angle to correct the image display position (up/down/left/right). Rotation means rotation on the basis of the rear lens unit. 3. Adjust the tilt angle so that the camera faces toward the monitoring object. Pan Tilt Lens rotation Tilt cramp screw Cover front

INSERTING/REMOVING A SD MEMORY CARD J Disconnect the power cable from the camera before inserting the SD memory card. Inserting a SD Memory Card Loosen the screw and open the cover of the SD memory card. Insert the SD card in the arrow direction as shown. Push the SD memory card in the direction of the arrow shown in the diagram. UNLOCK UNLOCK

40_ installation & connection J Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the SD memory card.

Removing a SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. UNLOCK UNLOCK

42_ installation & connection J Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the slot when released. To remove the SD memory card, set the card to in menu and press [Apply ( )] button. (Page 102) Removing the SD memory card while it’s in use for saving may damage the data stored in the card.

MEMORY CARD INFORMATION (NOT INCLUDED) What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Selecting a memory card that’s suitable for you Your camera supports SD/SDHC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card. For your camera, we recommend you use a memory card from the following manufacturers: SD/SDHC Memory Card : Sandisk, Transcend Memory cards of 4GB ~ 32GB is recommended for using with this camera. Playback performance can be affected depending on the speed of memory card, so use the high-speed memory card. It is recommended to use memory cards of at least class 6 speed. Memory Card Use SD and SDHC memory cards feature a switch that disables writing data on to the media. Having this switch to the Lock position will prevent accidental deletion of data stored in the memory card but at the same time will also prevent you from writing data on to the media. Memory Card Components SD/SDHC Lock Switch Contacts

44_ installation & connection CONNECTING WITH OTHER DEVICE J The BNC Out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes. If you keep the BNC cable connected, a risk of lightening may cause damage or malfunction to the product. UNLOCK UNLOCK Monitor to install Power Ethernet Monitor to install Ethernet Power Grounding cable

Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. Power Supply Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera. J If both PoE (Power over Ethernet) and DC 12V are supplied, the product will operate with the first- applied power source. - You can also use a router featuring PoE to supply power to the camera. - Use PoE that is compliant with the IEEE802.3af protocols. - It is advisable to use only one power source from PoE and DC12V. The heater will operate properly only by the power source of PoE. (SNV-7082) - If using DC 12V, the heater will not operate at all. - Use PoE in a low-temperature place of less than -10°C. Be careful not to reverse the polarity when you connect the power cable. If you want to connect an external device, you must turn off the external device before proceeding. Electrical Resistance of Copper Wire at [20°C (68°F)] Copper Wire Gauge (AWG) #24(0.22mm2) #22(0.33mm2) #20(0.52mm2) #18(0.83mm2) Resistance (Ω/m) 0.078 0.050 0.030 0.018 Drop Voltage (V/m) 0.028 0.018 0.011 0.006 Recommended Distance (m) Less than 20 Less than 30 Less than 30 Less than 30 As shown in the table above, you may encounter a voltage-sag depending on the wire length. If you use an excessively long wire for camera connection, the camera may not work properly. - Camera Operating Voltage : DC 12V±10% - Voltage drop measurements on the chart above may vary depending on the type and manufacture of the copper cable.

46_ installation & connection Grounding the Product (SNB-7002) Use a screw driver to connect earth grounding cable to the ground terminal below the power inlet terminal. J Grounding protects the product from a surge or lightning. When grounding, make sure to turn the product’s power off. Recommended Grounding Cable • Length : Less than 3M • Gauge : 18 AWG or bigger Ex) UL1007 AWG 18/16, UL1015 AWG18/16/14/12, UL2468 AWG18/16/14

Connecting to Audio Input/Output UNLOCK Network PC Microphone Speaker Microphone Speaker Amp Microphone Amp Speaker Microphone Amp Amp Microphone Speaker Speaker

48_ installation & connection 1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the microphone is connected to. 2. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the amplifier that the speaker is connected to. 3. Check the specifications for audio input. • Audio Codec G.711 PCM. μ-law 64kbps 8kHz / G.726 (16Kbps, 24Kbps, 32Kbps, 40Kbps) sampling • Full duplex Audio • Audio in Used for mono signal line input (Max.2.4 Vpp) • Audio out Used for mono signal line output (Max.2.4 Vpp) • Line out impedance 600 Connecting to the I/O port box (SNB-7002) Connect the Alarm I/O signal to the corresponding port of the rear port box. • ALARM IN : Used to connect the alarm input signal. • ALARM OUT : Used to connect the alarm output signal. • GND : Used for earth-grounding.

Connecting to the I/O port box (SND-7082/SND-7082F/SNV-7082) Connect the Alarm I/O cable to the corresponding port of the inner port box. • ALARM IN : Used to connect the alarm input signal. • ALARM OUT : Used to connect the alarm output signal. • GND : Used for earth-grounding. To connect the external sensor Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port. Alarm I/O Wiring Diagram UNLOCK 1 : ALARM IN 4 : - 2 : ALARM OUT 5 : - 3 : GND

network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN 1. Launch an Internet browser on the local PC. 2. Enter the IP address of the camera in the address bar of the browser. M A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator. By factory default, the IP address will be assigned from the DHCP server automatically. If there is no DHCP server available, the IP address will be set to 192.168.1.100. To change the IP address, use the IP Installer. For further details on IP Installer use, refer to “Static IP Setup”. (Page 55) UNLOCK UNLOCK Camera Camera Local PC INTERNET Firewall External Remote PC DDNS Server (Data Center, KOREA)

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM 1. Use the cross LAN cable to connect the network cable directly to your PC. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3. Use the Internet browser to connect to the web viewer. 4. Move to [Setup] page. 5. Move to [Network] – [DDNS] and configure the DDNS settings. 6. Move to [Network] – [Interface], and set the network type to [DHCP]. 7. Connect the camera, which was removed from your PC, directly to the modem. 8. Restart the camera. M For registering the DDNS settings, refer to “Registering with DDNS”. (page 94) For configuring the DDNS settings, refer to “DDNS”. (page 93) For setting the network type, refer to “Interface”. (page 91) UNLOCK Camera External Remote PC DDNS Server (Data Center, KOREA) DSL/Cable Modem INTERNET

network connection and setup CONNECTING THE CAMERA DIRECTLY TO A PPPoE MODEM 1. Use the cross LAN cable to connect the network cable directly to your PC. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3. Use the Internet browser to connect to the web viewer. 4. Move to [Setup] page. 5. Move to [Network] – [DDNS] and configure the DDNS settings. 6. Move to [Network] – [Interface], and set the network type to [PPPoE]. 7. Connect the camera, which was removed from your PC, directly to the modem. 8. Restart the camera. M For registering the DDNS settings, refer to “Registering with DDNS”. (page 94) For configuring the DDNS settings, refer to “DDNS”. (page 93) For setting the network type, refer to “Interface”. (page 91) UNLOCK Camera External Remote PC DDNS Server (Data Center, KOREA) PPPoE Modem INTERNET

CONNECTING THE CAMERA TO A BROADBAND ROUTER WITH THE PPPoE/CABLE MODEM This is for a small network environment such as homes, SOHO and ordinary shops. Configuring the network settings of the local PC connected to a Broadband Router Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions below. • Select :        or . • Follow the instructions below if you select : ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1 IP address : 192.168.1.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.1.1 ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1 IP address : 192.168.0.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.0.1 ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1 IP address : 192.168.xxx.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.xxx.1 M For the address of the Broadband Router, refer to the product’s documentation. For more information about port forwarding of the broadband router, refer to "Port Range Forward (Port Mapping) Setup”. (Page 60) UNLOCK UNLOCK Camera Camera Local PC Broadband Router PPPoE or Cable Modem PPPoE or Cable Modem External Remote PC DDNS Server (Data Center, KOREA) INTERNET

network connection and setup BUTTONS USED IN IP INSTALLER Item Description  Device Name Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search. b Alias This function is not currently implemented. c Mode Displays either , or for the current network connection status.  MAC(Ethernet) Address Ethernet address for the connected camera. Click the column to sort the list by Ethernet address. However, search will be stopped if clicked during the search. IP Address IP address. Click the column to sort the list by IP address. However, search will be stopped if clicked during the search.  Protocol Network setting for the camera. The factory default is “IPv4”. Cameras with the IPv6 setting will be displayed “IPv6”.  b c       m

Item Description  URL DDNS URL address enabling access from the external Internet. However, this will be replaced with the of the camera if DDNS registration has failed.  IPv4 Scans for cameras with the IPv4 setting.  IPv6 Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only.  Search Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked. Auto Set The IP Installer automatically configures the network settings.  Manual Set You should configure the network settings manually. m Exit Exits the IP Installer program. M For the IP installer, use only the installer version provided in the installation CD or use the latest one if available. You can download the latest version from the Samsung web site (www.samsungcctv.com). STATIC IP SETUP Manual Network Setup Run to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out. M For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function. 1. Select a camera in the search list. Check the MAC address of the camera on the camera’s label. Both the [Auto Set] and [Manual Set] buttons will be activated. 2. Click [Manual Set]. The Manual Setting dialog appears. The default values of , , , and of the camera will be displayed.

network connection and setup 3. In the

pane, provide the necessary information. • MAC (Ethernet) Address : The MAC address imprinted on the camera label is automatically displayed and requires no user setting. M You can configure the static IP settings only if the DHCP checkbox is unchecked. If not using a Broadband Router For setting , , and , contact your network administrator. 4. In the pane, provide necessary information. • HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. • VNP Port : Used to control the video signal transfer, defaulted to 4520. 5. Enter the password. Enter the password of “admin” account, which was used to access the camera. The default password is “4321”. J The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. If you want to change the password, refer to “Administrator password change” of the user setup. (page 118) 6. Click [OK]. Manual network setup will be completed.

If using a Broadband Router • IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.2~254 • Subnet Mask : The of the Broadband Router will be the of the camera. • Gateway : The of the Broadband Router will be the of the camera. M The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router. For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”. (Page 60) If the Broadband Router has more than one camera connected Configure the IP related settings and the Port related settings distinctly with each other. ex) Category Camera #1 Camera #2 IP related settings IP Address Subnet Mask Gateway 192.168.1.100 255.255.255.0 192.168.1.1 192.168.1.101 255.255.255.0 192.168.1.1 Port related settings HTTP Port VNP Port 8080 4520 8081 4521 M If the is set other than 80, you must provide the number in the address bar of the Internet browser before you can access the camera. ex) http://IP address : HTTP Port http://192.168.1.100:8080

network connection and setup Auto Network Setup Run to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out. M For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function. 1. Select a camera in the search list. Check the MAC address of the camera on the camera’s label. Both the [Auto Set] and [Manual Set] buttons will be activated. 2. Click [Auto Set]. The Auto Setting dialog appears. The , , and will be set automatically. 3. Enter the password. Enter the password of “admin” account, which was used to access the camera. The default password is “4321”. J The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. If you want to change the password, refer to “Administrator password change” of the user setup. (page 118) 4. Click [OK]. Auto network setup will be completed.

DYNAMIC IP SETUP Dynamic IP Environment Setup • Example of the Dynamic IP environment - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server - If connecting the camera directly to modem using the DHCP protocols - If IPs are assigned by the internal DHCP server via the LAN Checking the Dynamic IP 1. Run the IP Installer on the user’s local computer. Cameras allocated with address are shown in the list. 2. Select a camera from the search result. 3. Click the [Manual Set] button and check the camera’s address. If you uncheck , you can change IP to .

network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. Manual Port Range Forwarding 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2. Select and for each connected camera to the Broadband Router. Each port number for the Broadband Router should match that specified in - - from the camera’s web viewer menu. 3. When done, click [Save Settings]. Your settings will be saved. M Above sample instructions are based on the CISCO’s Broadband Router. The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router.

Setting up Port Range Forward for several network cameras When several network cameras are connected to one Broadband Router device, you should forward the TCP 943 port of the router to the TCP 943 port of a connected camera. J If you don't set properly the TCP 943 port of the router, you cannot get any video stream from the web page of the camera. • TCP 943 port is a port for the Silverlight policy server of a camera. • You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. • You cannot change the Silverlight policy server port of a camera. • You can change the ports of the camera except the policy server port through its configuration web pages. When Camera1 and Camera2 are connected to a router : User Internet Ù Broadband Router Start End Protocol IP Address 943 943 TCP 192.168.1.100 3000 3000 TCP/UDP 192.168.1.100 3001 3001 TCP/UDP 192.168.1.101 4520 4520 TCP/UDP 192.168.1.100 4521 4521 TCP/UDP 192.168.1.101 8080 8080 TCP/UDP 192.168.1.100 8081 8081 TCP/UDP 192.168.1.101 Ú Camera1 (192.168.1.100) Web Server Port 8080 Device port 4520 RTSP port 3000 Policy server port 943 Ù Camera2 (192.168.1.101) Web Server Port 8081 Device port 4521 RTSP port 3001 Policy server port 943 Ù

network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run the IP Installer. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. M Access to the camera can also be gained by typing the camera's IP address in the address bar of the Internet browser. CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET Since using the IP Installer on a remote computer that is not in the Broadband Router’s network cluster is not allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL. 1. Before you can access a camera in the Broadband Router network, you should have set the port range forward for the Broadband Router. 2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the IP address of the Broadband Router in the address bar. ex) http://www.samsungipolis.com/[Product ID] M For registering the DDNS settings, refer to “Registering with DDNS”. (page 94)

web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100  http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111  http://[2001:230:abcd:ffff:0000 :0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar. ex) IP address : 192.168.1.100:HTTP Port number(8080)  http://192.168.1.100:8080 - the Login dialog should appear. Using URL 1. Launch the Internet browser. 2. Type the DDNS URL of the camera in the address bar. ex) URL address : http://www.samsungipolis.com/[Product ID] - the Login dialog should appear.

web viewer To check the DDNS address If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE modem, the IP address of your network will be changed each time you try to connect to the ISP (Internet Service Provider) server. If this is the case, you will not be informed of the IP address changed by DDNS. Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP when you try to access the device. To register your device to the server, visit www.samsungipolis.com and register your device first, and then set the Web Viewer’s - to , as well as providing that had been used for DDNS registration. LOGIN Whenever you access the camera, the login window appears. Enter the User ID and password to access the camera. 1. Enter “admin” in the input box. The administrator ID, “admin”, is fixed and can not be changed. 2. Enter “4321” in the input box. If the password is changed, enter the changed password instead. 3. Click [OK]. If you have logged in successfully, you will the Live Viewer screen. M The default user ID is “admin”, and the default password is “4321”. For security purposes, ensure that you change the password in - . The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. If you check the “Remember my password” option when your input is done, in future you will be logged in automatically without being prompted to enter the login information. J You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut the image on the borders.

INSTALLING SILVERLIGHT RUNTIME If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will be redirected to the Silverlight Runtime installation page automatically when accessing the web viewer. To install on Windows OS 1. Click . 2. When the file download dialog pops up, click . 3. When the download is completed, click . 4. The Silverlight Runtime installation page will be displayed. to proceed with the installation.

web viewer 5. When done, click . To install on MAC OS 1. Run the file trailing with “.dmg”. 2. Run the install package file automatically created, ending with “.pkg”. 3. Click .

4. Select your language on the language selection screen, and click . 5. Click . 6. Click .

web viewer 7. Enter the password of the account currently logged in, and click and continue. 8. Once completed, click .

INSTALLING STW WebViewer PLUGIN If connecting to a camera for the first time, you will see the installation message. Then, install the required WebViewer Plugin to access the camera and control the video from it in real time. M Microsoft Visual C++ 2010 Redistribute Package should be installed on the PC before you can install the Web viewer plug-in. If Visual Studio 2010 is not installed yet, you will see the error message of “There is no VC++ 2010 runtime installed. Please install the runtime library.” Run the vcredist_x86.exe file which can be found from Samsung website at www.samsungcctv.com or the provided installation CD. The vcredist_x86.exe file is installer program of Microsoft’s Visual Studio 2010 redistributable package for 32-bit operating systems. 1. When accessing the start screen of the monitoring page, click the yellow warning message in the top of the page. 2. Click . 3. The security warning popup appears, click [Run]. 4. When the Web viewer plug-in is installed properly, you will see the live screen displayed.

web viewer USING THE LIVE SCREEN Item Description  Monitoring Move to the monitoring screen. b Playback Switch to the monitoring screen that plays recording data in the SD memory. c Setup Move to the Setup screen.  Viewer Screen Displays the Live video on the screen. You can use the mouse wheel to activate the digital zooming in Viewer screen. Profile type You can select a profile type in

Item Description  Full Screen Switch the current video to the maximum size of the monitor.  Capture Saves the snapshot as an image file in the .bmp or .jpg format.  Audio/Microphone Control Enable/disable audio and microphone, and controls volume. Alarm output Activate the Alarm Out port. Hide the context menu The left-corner context menu will disappear but only the menu icon. To capture the snapshot 1. Click [Capture ( )] on the scene to capture. The Capture dialog should appear. 2. Confirm the save path and click [Save] button. The screenshot will be saved in the specified path. M If you encounter an interrupted video when capturing the image with IE8 on a Windows 7-based PC, deselect “Turn On Protected Mode” from “Tools – Internet Options – Security”. To fit the full screen 1. Click the [Full Screen ( )] button. 2. This will fit the Viewer to the full screen. 3. To exit the full screen mode, press [Esc] on the keyboard. M For the Internet Explorer and Google Chrome browser, you can switch to the full screen.

web viewer To control the audio sound 1. Click [Audio ( )] icon to activate audio communication. 2. Use [ ] bar to control the volume. To control microphone 1. Click [Mic ( )] icon to activate the microphone. SEARCH AND PLAY BY EVENT 1. Click the [Playback ( )] button. 2. Specify the start time and end time of your search. 3. Select an event type for your search within the specified period. 4. Click the [Event search] button. The search results will be displayed in the list. M If more than 500 events are recorded within the search period, your search will be limited up to the date when the 500th event is recorded. For instance, if the search period is between 10th and 15th day of the month, and more than 500 events were recorded 10th through 11th, your search will be limited up to 11th day with a total of 500 events, and events after then (from 12th) will not be found. 5. Select a data item to play in the search list. 6. Click the [Play ( )] button. 7. To stop playing the video, click [Stop ( )]. 8. To return to the search screen, click [Exit ( )].

SEARCH AND PLAY BY TIME 1. Click [Time Search ( )]. 2. Click a desired date in the calendar. The video on the specified date will be played. 3. If the video playback is stopped, select a time and click [Play ( )]. The video on the selected time will be played. 4. While the video is being played, the recording time for the current video will be shown. 5. Search for the video forward or backward, and control the play speed. - To control the play speed If selecting ), the button will switch to x1, x2, x4, x8, and the play speed will increase accordingly. If selecting (, the button will switch to x8, x4, x2, x1, and the play speed will decrease accordingly. - To control the playback direction If you see the ) button with the play speed displayed, the video will be played forward; Whereas, if you see the ( button with the play speed displayed, the video will be played backward. 6. Move [Time bar ( )] to a desired time point of the video before playing it. The time containing a normal recoding file will be highlighted in blue; the time with the event recording will be highlighted in red.

web viewer To check time information of the playing video 1. Click the [About ( )] button. 2. Date and time information appears on the screen. To back up the searched video 1. During playback, click [ ] on the scene to back up. The scheduling window for backup start and end time appears. 2. Click [ ] button. The Save As window appears. 3. Confirm the save path and click [Save] button. The screenshot will be backed up to the specified path. To play the backup video The backup video will be saved in .avi format. The backup video can be played with any media player supporting the format on your PC.

network. 1. In the Live screen, click [Setup ( )]. 2. The Setup screen appears. J Microsoft Sliverlight 4.0 is required to be installed on the PC for setup pages that provide preview video. If not installed already, automatically moves to the Sliverlight setup. VIDEO & AUDIO SETUP Video profile 1. From the Setup menu, select the

The context menu may differ depending on the selected codec type. • Default profile : If no profile is selected when using the Web Viewer, the default video profile is applied. • E-mail/FTP profile : Video profile to be transferred to the specified email or FTP site. Only the MJPEG codec can be set as the E-mail/FTP profile. • Record profile : This is the profile that is applied to video recording. • Audio-In : Sets whether to use audio for video recordings. 7. According to your situation, set ATC (Auto Transmit Control) mode. • ATC mode : It adjusts the video properties according to the variance in the network bandwidth, controlling the bit rate. Adjusting the bit rate depends on the ATC mode. - Control framerate : Reduce the frame rate if the network bandwidth drops down. - Control compression : Control the compression rate if the network bandwidth drops down. Compression adjustment can cause deterioration of the image quality. If is set to , the encoding priority according to the ATC mode will be fixed as below: Bitrate control / ATC mode Control framerate Control compression CBR Framerate Compression • ATC sensitivity : Affect the transfer rate according to the variance in the network bandwidth. The transfer rate will be adjusted to the fastest if the bandwidth is , and adjusted to the latest if the bandwidth is . • ATC limit : If the quality or frame rate is adjusted, the property will be changed to the applied value (%) against the previous setting value (100%). Note that if you reduce the property value too much, you may encounter flickering on the screen. So it is advisable to adjust the value within the threshold. J It is recommended to apply ATC control only for cameras supporting ATC. Set the ATC sensitivity to in a network environment with high variance in the network bandwidth. If the network connection is unstable, you may encounter flickering on the screen. 8. When done, click [Apply ( )]. 76_ setup screen

You can add as many codecs as necessary so that a variety of profiles can be applied according to the recording condition. 1. Select one from the

GOV(Group of Video object planes) is a set of video frames for H.264 compression, indicating a collection of frames from the initial I-Frame (key frame) to the next I-Frame. GOV consists of 2 kinds of frames: I-Frame and P-Frame. I-Frame is the basic frame for the compression, also known as Key Frame, which contains one complete image data. P-Frame contains only the data that has changed from the preceding I-Frame. You can specify a value between 1 and 15 for the H.264 CODEC. Video setup 1. From the Setup menu, select the

You can specify a certain area of the camera video to be protected for your privacy. 1. Set it to . 2. When done, click [Apply ( )]. 3. Select the type and color masking of desired privacy area. • Rectangle : Place the cursor at a point in the video and drag it to whatever you need. You can overlap rectangles for privacy area setup. • Quadrilateral : Select 4 vertices (forming a quadrilateral) on the video. 4. Click on the video screen and drag to set the desired area. 5. Provide a name and press [OK]. 6. If you want to delete an area in the list, select one and click [Delete ( )]. Audio setup You can configure the I/O settings of the audio source from the camera. 1. From the Setup menu, select the

- G.711 : A audio codec standard, it uses 64 Kbps PCM (Pulse Code Modulation) encoding. ITU standard audio codec that is adequate for digital voice transfer in PSTN network or through a PBX. - G.726 : ITU standard audio codec applying ADPCM (Adaptive Differential Pulse Code Modulation) for variable bit rates of 40/32/24/16 Kbps to 64 Kbps PCM encoding. • Bitrate : Set the bit rate to differentiate compression ratio if using G.726 codec. • Gain : Sets the input audio gain. 4. Set the audio output level. • Enable : Sets whether to use audio output. • Gain : Sets the output audio gain. 5. When done, click [Apply ( )]. Camera setup You can change the camera settings according to the environment where the camera is located. 1. From the Setup menu, select the

In a scene where the difference between bright and dark is severe, you can increase the brightness of the dark area alone to regulate the overall brightness. 1. Select . 2. Set to . 3. Configure the and settings as necessary. • Level : Adjust the level of the dynamic range. • D-Range : Select the amplitude area of the dynamic range. White balance Setup You can correct the image colors based on white under any lighting conditions. 1. Select . 2. Select . • ATW : Corrects the colors of the camera video automatically. • Manual : You can adjust the red and blue gains of the camera video manually. • AWC : Corrects the colors of the camera video to be optimized to the current lighting condition and screen mode. To obtain the optimal condition for the current lighting, put the focus of the camera to a white paper and press the [AWC Set] button. If the lighting environment is changed, you should readjust the settings accordingly. • Outdoor : Automatically corrects the video colors of the camera to be optimized to the outdoor environment. • Indoor : Automatically corrects the video colors of the camera to be optimized to the indoor environment. M In AWC mode, click the [AWC Set] button if you want to keep the white balance level of the current image. J The white balancing may not work properly in the following conditions: If this is the case, switch to AWC mode. - If the surrounding condition of the object is out of the temperature correction range ex) Clear sky, sunset - If the surrounding of the object is dark - If the focus of the camera directly faces the florescent lighting or if the camera is installed in a place of variable illumination, the white balancing operation may be unstable. English _81 ● SETUP SCREEN

more clearly. 1. Select . 2. Set to . 3. Set . You can change the level to adjust the brightness of the monitoring area. 4. Set the levels to specify the target area. HLC (Highlight Compensation) Setup When a strong light such as streetlamp or headlight faces forward to the camera, you can mask that exposed area in order to protect it from being saturated. 1. Select . 2. Set to . 3. Set the and the . • HLC level : Adjust the brightness level so as to remove the incoming highlight from a specific condition. • Mask tone : Adjust the mask tone of the highlighted area. M At night operation, this function will be activated only if the incoming highlight exceeds a certain area in a low contrast environment. At night, HLC will not function if the scene is either too bright or too dark. 82_ setup screen

1. Select . 2. Set to . 3. Specify the . M If applied with WDR, noise may be found on the border between the brighter and darker areas. Ex) Exposure Setup (SNB-7002) You can adjust the exposure level of the camera. 1. Select . 2. Select each item and set it properly. • Brightness : Adjust the screen brightness. • Shutter mode : Adjust the electronic shutter of the camera. - ESC (Electronic shutter control) : Adjust the shutter speed automatically according to the ambient brightness. This will be activated if is set to . English _83 ● SETUP SCREEN

You can select one between 1/30 and 1/12000sec in 2 mega mode, and select one between 1/20 and 1/12000sec in 3 mega mode. - A.FLK (Anti flicker) : Select this feature if you encounter a flickering screen due to a frequency mismatch with the ambient lighting. • Shutter speed : Control the shutter speed manually. • SSNR3 : Specify the use of noise reduction. • SSNR3 level : Adjust the noise reduction level. • Sens-up mode : Automatically senses the darkness level at night or in a low contrast scene and extends the accumulation time accordingly for a bright and sharp image. If you set the shutter mode to Manual/A.FLK, SENS-UP mode will be deactivated. The greater the Sens-Up factor is, the brighter the screen becomes but it may result in an afterimage or video delay. • Sens-up limit : Set the work condition to Auto mode in a low contrast scene. • Lens : Select to set the lens mode of the camera to Manual or Auto. - DC(Auto) : Select this if you use the DC lens. Only the iris is adjusted automatically, but the focus is not controlled automatically. - Manual : Select this if you use a lens on which you adjust the iris and focus manually. • AGC mode : Select AGC Control mode. Adjust the gain value of the video (that, in particular, was recorded at a low contrast scene and had a lower brightness level than normal) to control the video brightness. Exposure Setup (SND-7082/SND-7082F/SNV-7082) You can adjust the exposure level of the camera. 1. Select . 2. Select each item and set it properly. • Brightness : Adjust the screen brightness. • Shutter mode : Adjust the electronic shutter of the camera. - ESC (Electronic shutter control) : Adjust the shutter speed automatically according to the ambient brightness. This will be activated if is set to . 84_ setup screen

You can select one between 1/30 and 1/12000sec in 2 mega mode, and select one between 1/20 and 1/12000sec in 3 mega mode. - A.FLK (Anti flicker) : Select this feature if you encounter a flickering screen due to a frequency mismatch with the ambient lighting. • Shutter speed : Control the shutter speed manually. • SSNR3 : Specify the use of noise reduction. • SSNR3 level : Adjust the noise reduction level. • Sens-up mode : Automatically senses the darkness level at night or in a low contrast scene and extends the accumulation time accordingly for a bright and sharp image. If you set the shutter mode to Manual/A.FLK, SENS-UP mode will be deactivated. The greater the Sens-Up factor is, the brighter the screen becomes but it may result in an afterimage or video delay. • Sens-up limit : Set the work condition to Auto mode in a low contrast scene. • Iris : You can set the camera iris to Auto or Manual to your preference. - Auto : Automatically sets the iris adaptively to the ambient lighting and shutter speed. - Manual : Sets the iris to its maximum aperture. • AGC mode : Select AGC Control mode. Adjust the gain value of the video (that, in particular, was recorded at a low contrast scene and had a lower brightness level than normal) to control the video brightness. Special Setup (SNB-7002) 1. Select . 2. Select each item and set it properly. • Day & night : You can switch the mode to adjust the black and white level as well as the colors. - Color : Always displays the video in colors. - B/W : Always displays the video in black and white. - Auto : Displays in color mode during normal daytime and switches to black and white mode in a low contrast scene at night. If you set the AGC mode to from , the AUTO DAY/NIGHT mode will be disabled accordingly. - External B/W : Control the image modes of Color and B/W when an external IR is synchronized via the Alarm In port. English _85 ● SETUP SCREEN

order to enable the switch between day and night modes. • Duration : Specify the time interval of lighting at which the sequence operation is triggered. • Simple focus after D/N : When switching day/night mode, automatically runs focus adjustment. When using IR lens with the camera, set this to . M Setting option may cause false focus adjustment under a specific condition. For further details, refer to “Focus setup”. (Page 89) • Sharpness mode : Adjust the overall sharpness of the image. If selecting , you can adjust the sharpness of the image. • Sharpness level : The higher the level is, the sharper and clearer the outline of the image becomes. • Gamma : Adjust the contrast of the image. • Color level : Adjust the color level of the image. • Alarm in : Set the image to Color or B/W depending on the Open/Close state of the alarm sensor. If the Day & Night mode is set to Externel B/W, the alarm-in function of the event-alarm input page will be disabled. Special Setup (SND-7082/SND-7082F/SNV-7082) 1. Select . 2. Select each item and set it properly. • Day & night : You can switch the mode to adjust the black and white level as well as the colors. - Color : Always displays the video in colors. - B/W : Always displays the video in black and white. - Auto : Displays in color mode during normal daytime and switches to black and white mode in a low contrast scene at night. If you set the AGC mode to from , the AUTO DAY/NIGHT mode will be disabled accordingly. - External B/W : Control the image modes of Color and B/W when an external IR is synchronized via the Alarm In port. 86_ setup screen

order to enable the switch between day and night modes. • Duration : Specify the time interval of lighting at which the sequence operation is triggered. • Sharpness mode : Adjust the overall sharpness of the image. If selecting , you can adjust the sharpness of the image. • Sharpness level : The higher the level is, the sharper and clearer the outline of the image becomes. • Gamma : Adjust the contrast of the image. • Color level : Adjust the color level of the image. • Alarm in : Set the image to Color or B/W depending on the Open/Close state of the alarm sensor. If the Day & Night mode is set to Externel B/W, the alarm-in function of the event-alarm input page will be disabled. OSD Setup 1. Select . 2. Select each item and set it properly. • Camera title : Specify whether or not to display the camera title on the screen. You can enter up to 15 characters for the title. • Camera title position X, Y : Specify the coordinates where the camera title is displayed on the screen. Time OSD Setup 1. Select . 2. Select each item and set it properly. • Time display : Specify the use of time display on the screen. • Date format : Specify the date format that will be displayed on the screen. • Time position display X, Y : Specify the position of time display on the screen. • Display weekday : Specify the use of date display date on the screen. English _87 ● SETUP SCREEN

Set a desired area of the video incoming from the camera as ROI area and specify the detection sensitivity for the area. 1. From the Setup menu, select the

You can adjust the focus of video image. 1. From the Setup menu, select the

You can adjust the focus and zoom ratio of video image. 1. From the Setup menu, select the

a camera into a general Host Name so that the user can easily remember it. 1. From the Setup menu, select the tab. 2. Click . 3. Select the connection type. 4. Type in the DDNS items according to the selected type. • Samsung DDNS : Select this if you use the DDNS server provided by Samsung Techwin. - Product ID : Enter the product ID that is registered with the Samsung DDNS service. - Quick connect : It sets port forwarding automatically when used with a UPnP (Universal Plug and Play) supporting router. • Public DDNS : Select one of provided public DDNS servers when you use a public DDNS server. - Service : Select desired public DDNS service server. - Host name : Enter the name of the host that is registered with the DDNS server. - User name : Enter the user name for the DDNS service. - Password : Enter the password for the DDNS service. 5. When done, click [Apply ( )]. J If selected , be sure to select Samsung DDNS service. English _93 ● SETUP SCREEN

To register your product with the Samsung DDNS 1. Visit the iPOLiS web site (www.samsungipolis.com) and sign in with a registered account. 2. From the top menu bar, select - . 3. Click [PRODUCT REGISTRATION]. 4. Enter the product ID. You must perform the duplicate check for the ID that you entered. 5. Select a and specify the . 6. Specify the product location with a description if necessary. 7. Click [REGISTRATION]. The product will be added to the product list that you can check. 94_ setup screen

1. From the DDNS setup page, set to . 2. Provide the that you registered product ID with the DDNS site. 3. Click [Apply ( )]. When the connection is successfully made, you will see the message of <(Success)> on the screen. Configuring public DDNS in Camera Settings 1. Open the DDNS settings page and select for . 2. Enter the corresponding site’s host name, user name and password. 3. Click [Apply ( )] button. If the connection properly establishes, <(Success)> appears. 4. When done, click [Apply ( )]. M To use DDNS service properly, both DDNS setup and the router’s port forwarding setup are required. For port forwarding setup, refer to “Port Range Forward (Port Mapping) Setup” (page 60) English _95 ● SETUP SCREEN

1. From the Setup menu, select the tab. 2. Click . 3. Select . • Deny : If selecting this, access from those IPs that are added to the filtering will be restricted. • Allow : If selecting this, access from only those IPs that are added to the filtering will be accepted. 4. Click the [Add ( )] button. The IP list will be created. 5. Provide the IP that you want to grant or deny access from. When you enter an IP address and a Prefix, the list of IP addresses available will appear in the right-side filter range column. M If selected for IP Filtering and of is set to , both IPv4 and IPv6 addresses of the computer currently configuring should be assigned. The IP address of the computer used for the current setup cannot be added to , it should be added to . Only the IP addresses that are set to will be displayed in the filter column. 6. Select an IP to delete from the list. Click the [Delete ( )] button. 7. When done, click [Apply ( )]. 96_ setup screen

1. From the Setup menu, select the tab. 2. Click . 3. Select a secure connection system. To access the camera using HTTPS mode, you have to type the IP address for the camera in the form of “https://”. If you failed to configure the Web viewer settings in HTTPS mode with Internet Explorer, edit the Internet options as follows: 4. Search for the public certificate that you want to install on the camera. To install the certificate on the camera, you need to provide a certificate name (it can be arbitrarily assigned by the user), certificate file issued from the certification authority and a key file. The item will be active only if there exists a public certificate installed. 5. When done, click [Apply ( )]. Installing the certificate 1. Enter the certificate name. 2. Select the certificate file to be installed and certificate key, and click [Install ( )] button. Deleting the certificate 1. Click [Delete ( )] button. 2. To delete a public certificate, you should access the network video decoder in the mode of or . English _97 ● SETUP SCREEN

the certification. 1. From the Setup menu, select the tab. 2. Click <802.1x>. 3. Set the . • Enable IEEE 802.1x : Specify the use of the 802.1x protocol. • EAPOL version : Select version 1 or 2. • ID : Enter the client certificate ID. • Password : Enter the client private key password. If the key file used is not encrypted, you don’t need to enter it. J If the connected network device does not support the 802.1x protocol, the protocol will not operate properly even if you set it. 4. Install/remove the certificate. • CA certificates : Select a public certificate that contains the public key. • Client certificate : Select a public certificate that contains the client certificate key. • Client private key : Select a public certificate that contains the client private key. 5. When done, click [Apply ( )]. To install/remove 802.1x related certificates 1. Press the [Browse ( )] button for each item and select a certificate to install. 2. If no certificate is installed, you will see “Not Available” appearing next to the selected item. 3. Press the [Install ( )] button to start installation with a message of “Installed” next to the item. 4. Press the [Delete ( )] button to remove the certificate. 98_ setup screen

1. From the Setup menu, select the tab. 2. Click . 3. Click the [Add ( )] button. The IP list will be created. 4. Enter an IP address to which you will apply QoS. M The default prefix for IPv4 is 32; For DSCP, the default is set to 63. Only the IP addresses that are set to can be prioritized. 5. Select an IP to delete from the list. Click the [Delete ( )] button. 6. When done, click [Apply ( )]. SNMP With the SNMP protocols, the system or network admin can monitor the network devices on a remote site, and configure the environment settings. 1. From the Setup menu, select the tab. 2. Click . 3. Specify the . • Enable SNMP v1 : SNMP version 1 will be active. • Enable SNMP v2c : SNMP version 2 will be active. - Read community : Provide the name of the read community where you can access to the SNMP information. The default name is . - Write community : Provide the name of the write community where you can access to the SNMP information. The default name is . English _99 ● SETUP SCREEN

- Password : Specify the default password for SNMP version 3. The default password is . The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. Password should be longer than 8 characters, no more than 16 characters. 4. When done, click [Apply ( )]. J SNMP v3 is only able to be set when the secure connection mode is HTTPS. Refer to “SSL”. (page 97) EVENT SETUP FTP / E-mail You can configure the FTP/E-mail server settings so that you can transfer the images taken with camera to your PC if an event occurs. 1. From the Setup menu, select the tab. 2. Click . 3. Select or and enter / select a desired value. • FTP configuration - Server address : Enter the IP address of the FTP server that you transfer the alarm or event images to. - ID : Enter the user ID with which you will log in to the FTP server. - Password : Enter the user account password for logging into the FTP server. - Upload directory : Specify the FTP path where you will transfer the alarm or event images. 100_ setup screen