THOMSON RR95 Manual 

CAUTION: For UK Only CONNECT THE MAIN LEAD INTO AC MAINS POWER SOCKET POWER SUPPLY 230V. It must not be connected to D.C. mains. Note: The mains lead of the set is fitted with a moulded plug. If the mains socket are not compatible or if for any reason the plug is removed please follow the directions below. The moulded plug cannot be rewired and if removed must be disposed of safely. DO NOT under any circumstances plug the severed plug into any mains socket as this could result in electric shock. Important: If the plug is removed, rewire the new plug as follow: The wires in the mains plug are coloured in accordance to the following code: BLUE = NEUTRAL & BROWN = LIVE BLUE BROWN If the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: BLUE wire to the terminal coded N (Neutral) or coloured black. BROWN wire to the terminal coded L (Live) or coloured red. DO NOT make any connection to the terminal in the plug which is marked by the letter E or by the earth symbol or coloured green or green and yellow. A fused plug must be fitted with a 3A fuse approved by ASTA or BS1362 and fuse covers must be always be securely replaced. If your set does not work, the fuse may be blown. MAINS CONNECTIONS: (For UK, see inside front cover) MAINS OUTLET POWER SUPPLY: 230V ~50Hz Note: Power is fed to the unit even when it is not functioning. To cut the power supply off, the power cable must be unplugged. RR95 EN 3/20/03, 2:17 PM 1

bathrooms and pool side. Do not expose this appliance to rain or moisture Avoid storing the system at humid places or near abnormally heated areas. Power is continuously supplied to the system. To disconnect power completely, unplug the power cord from the power outlet. Do not expose this appliance to dripping and splashing. WARNING: TO PREVENT FIREOR ELECTRICAL SHOCK HAZARD,DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. SEE MARKING ON BOTTOM / BACK OF PRODUCT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THE EXCLAMATION POINT WITHIN THE T R I A N G L E I S A WARNING SIGN ALERTING YOU OF I M P O R T A N T I N S T R U C T I O N S A C C O M PA N Y I N G T H E P R O D U C T. THE LIGHTNING FLASH AND ARROW- HEAD WITHIN THE TRIANGLE IS A WA R N I N G S I G N ALERTING YOU OF " D A N G E R O U S VOLTAGE" INSIDE THE PRODUCT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER ( O R BAC K ) . N O U S E R - SERVICEABLE PARTS IN- SIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Please respect the environment. Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling. TECHNICAL SPECIFICATIONS: Power supply AC 230V ~50Hz Clock backup:9V 6F22 Power consumption: 7W RR95 EN 3/20/03, 2:18 PM 2

This clock radio is equipped with a memory holding system that can be powered with a 9V battery (not included). The power failure protection circuit will not operate unless battery is installed. When normal household power is inter- rupted, or AC line cord is unplugged, the battery will power the clock radio to keep track of time and alarm settings pro- grammed into memory. When the battery backup functions, the digital display will not be backlighted, however, the function of alarm still occurs during the power in- terruption if remaining battery power is adequate. Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm. Install battery as follows: 1. Remove battery compartment door (lo- cated at the bottom of the radio) by ap- plying thumb pressure to area indicated on battery door and then lift the door out and off the cabinet. 2. Connect a 9V battery to the connector plug. 3. Insert battery in the compartment and replace the compartment door. Power Failure Indicator When AC power is interrupted (discon- nected) for a short period of time, both time and alarm settings will change (un- less optional battery is installed). After AC power is restored (reconnected), the Digi- tal Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings. Note: Alkaline (NEDA 1604A / IEC 6LR61) battery is recommended. Carbon Zinc (NEDA 1604 / IEC 6F22) bat- tery may be used but memory holding time will be substan- tially reduced. Memory holding time for a fresh alkaline battery is approximately 8 hours (if radio or alarm is not operated), which should take care of short, nuisance-type AC power failures. To preserve battery life, the radio should remain plugged into an AC outlet. As batteries get older, their voltage drops and memory may be lost. Be sure to replace the battery periodically. Battery should be removed if the radio will be stored for more than one month. Leaky batter- ies may badly damage the clock radio. RR95 EN 3/20/03, 2:18 PM 3

EN Setting the Wake Time 1. Press the SET button once to set ALARM 1 (1 will flash on display), twice to set ALARM 2 (2 will flash on display). 2. Press REV or FWD to set wake time. 3. When wake time is set. You can exit set mode by pressing SET button until no flashing sign or clock icon is dis- played. Setting Clock Time Your digital clock operates on a 24-hour standard mechanism. 1. Press the SET button until a clock icon is shown on display. 2. Press REV or FWD to set the clock time. When you press and hold REV or FWD, the time decrements or increments will follow by a faster rate. No adjustment can be made when LOCK mode is se- lected. Example 1: ALARM 1 mode setting: 8:50 AM Wake to Alarm Example 2: ALARM 2 mode setting: Alarm off A SLEEP NAP Set 1 2 Memory Recall ALARM Cancel BAND ALARM RADIO Re w TU NE Fw d TI ME SET OFF ON RR95 EN 3/20/03, 2:18 PM 4

Waking by Selected Source Programme You may be woken up by music or alarm . 1. Select an AM or FM station. (refer to “Tuning the Stations”) 2. Set wake time (see above direction). 3. Press the ALARM 1 or ALARM 2 but- ton to select waking up by music or alarm. An indicator is up next to the selected setting. 4. Adjust the volume by turning VOLUME. Note: When you turn off the alarm or the music by pressing OFF OFF OFF OFF OFF, the alarm or the music will turn on at the same time tomorrow. Note: The unit equips with GRAD-U- GRAD-U- GRAD-U- GRAD-U- GRAD-U- WAKE WAKE WAKE WAKE WAKE feature, the alarm tone volume will increase gradually to its maximum in about 30 to 45 seconds. Sleep Mode In sleep mode, the radio will turn off au- tomatically. Simply: 1. Press SLEEP then the time display will exhibit 0:59 and the radio will turn on. 2. While holding SLEEP, press REV or FWD to set the sleep time. The time range is from 1 minutes to 2 hours. 3. Release SLEEP and the current time will be shown again. The radio is turned on and you may select the station as usual. The radio will turn off when the preset time elapses. If you decide to turn off the radio sooner, press SNOOZE or OFF. 4. When SLEEP is activated again, the sleep time will be the same as the one you set before. 5. Press SLEEP to read the remaining sleep time. Nap Mode This function wakes you up after a short period of time. Simply: 1. Press NAP and release. The NAP indi- cator will flash. 2. When the indicator is flashing, press REV or FWD to adjust nap time. The time range is from 10 minutes to 2 hours. 3. The clock will be shown after 5 seconds if no button is pressed. The NAP indica- tor will lit up. 4. Press NAP once to show time left. Stop the Nap alarm Press NAP or follow “Turning off Alarm”. Notes: 1. Press and hold NAP NAP NAP NAP NAP to cancel the nap setting. 2. Only alarm sound can be selected. 3. If the radio is currently on (by press- ing ON/BAND ON/BAND ON/BAND ON/BAND ON/BAND button), then the radio will be on after NAP NAP NAP NAP NAP is pressed. RR95 EN 3/20/03, 2:18 PM 5

EN Tuning the Stations 1. Press ON/BAND (located on the top of the radio) to turn on the radio. 2. Press ON/BAND to change the broad- cast band (FM/MW for RR95M only, FM/ LW for RR95L), press the OFF button to turn off the radio. 3. Press or to select a station. 4. If you want to memorize this station, press MEMORY SET button once, and press MEMORY RECALL button to choose the station number you want to record in, once you choose a num- ber, press MEMORY SET again to con- firm. 5. If you set the station in the AL location, it will be the wake up station of the alarm. Automatic station search 1. Press ON/BAND (located on the top of the radio) to turn on the radio. 2. Press and hold or for 2 seconds, it will automatically search a station for you. Note: This unit can store up to 11 preset stations, while AL location is for the wake up station. The descriptions and characteristics in this owner’s manual are for the purpose of general reference only and not as a guarantee. In order to provide you with the highest quality product, we may make changes or modifications without prior notice. The English version serves as the final reference on all product and operational details should any discrepancies arise in other languages. SLEEP NAP Set 1 2 Memory Recall ALARM Cancel BAND ALARM RADIO Re w TU NE Fw d TI ME SET OFF ON RR95 EN 3/20/03, 2:18 PM 6

Turning off Alarm Silence the alarm momentarily Press SNOOZE. The alarm will sound again when the snooze period is over. Stop the alarm Press OFF. Then the alarm will be on the following day at the same time. Disable the alarm permanently 1. Press CANCEL button. 2. The ALARM 1 and ALARM 2 indicator will be flashing. 3. Press ALARM 1 or ALARM 2 button within 3 seconds to deactivate the alarm function permanently, “OFF” will be shown when the above procedures are done. Tip: You can activate the previously set alarm time by pressing ALARM 1 1 1 1 1 or ALARM 2 2 2 2 2 button. Snooze Alarm Operation This operation allows extra sleep time af- ter the alarm is on. The alarm will be off by pressing SNOOZE until the snooze pe- riod is over. Snooze function can be used repeatedly up to 2 hours. After this, the alarm will yurn off until the next alarm conditions are met. Set the “quiet time” as follow: 1. Press and hold SNOOZE. 2. Press REV or FWD to set the “quiet” period (the default time is 9 minutes) from 1 minute to 30 minutes. Release button, then the “quiet” period is set. Seconds Time Display The unit may display in seconds. 1. The clock should be in normal mode. 2. Press or to show seconds display. 3. Release to return to the hour and minute display. Brightness control You can adjust the backlight by the BRIGHTNESS button, there are three modes you may select from: OFF - Backlight always off. HIGH - Backlight always high. LOW - Backlight always low. VOLUME DISPLAY Brightness RR95 EN 3/20/03, 2:18 PM 7