Samsung 4240 Owner's Instructions Manual

please read this manual thoroughly, and retain it for future reference. ON-SCREEN MENUS PICTURE IN PICTURE (PIP) TELETEXT / TELEWEB (OPTION) BN68-00597A-01 4/2/04 6:38 PM Page 1

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image. ◆Cell Defect The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9 percent active cells, there may be some cells that do not produce light or remain lit. ◆Height The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height and do not install and operate there. ◆Warranty - Warranty does not cover any damage caused by image retention. - Burn-in is not covered by the warranty. BN68-00597A-01 4/2/04 6:38 PM Page 2

Owner’s Instructions Remote Control/ AAA Batteries Power Cord Ferrite Core for Speaker Wire Ferrite Core for Side AV Cable S-VIDEO Cable PC Cable DVI Cable Antenna Cable Scart Cable PC Audio Cable Component Cables (RCA) Sold Separately This feature bring you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, much detailed image to you. DNIeTM technology will fit every signals into your eyes. Checking Parts Ferrite Cores The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector. When you connect Side AV cable to the S-VIDEO2/AV3, first bind Side AV Cable round the ferrite core to secure it. BN68-00597A-01 4/2/04 6:38 PM Page 3

■ Your New Plasma Display Panel................................................................... 6 ■ Infrared Remote Control................................................................................ 8 ■ Inserting the Batteries in the Remote Control................................................ 9 ■ Assembling the Stand-Base .......................................................................... 9 ■ Installing the Display on the Wall Attachment Panel ..................................... 10 ■ Connecting to an Aerial or Cable Television Network ................................... 12 ■ Connecting a Satellite Receiver or Decoder.................................................. 12 ■ Switching On and Off..................................................................................... 13 ■ Placing in Standby Mode............................................................................... 13 ■ Becoming Familiar with the Remote Control ................................................. 14 ■ Setting Up Your Remote Control................................................................... 15 ■ Plug & Play Feature....................................................................................... 16 ■ Choosing Your Language.............................................................................. 17 ◆SETTING THE CHANNELS ■ Storing Channels Automatically..................................................................... 18 ■ Storing Channels Manually............................................................................ 19 ■ Skipping Unwanted Channels ....................................................................... 21 ■ Sorting the Stored Channels ......................................................................... 22 ■ Assigning Names to Channels ...................................................................... 23 ■ Using the LNA (Low Noise Amplifier) Feature............................................... 24 ■ Activating the Child Lock ............................................................................... 25 ■ Displaying Information................................................................................... 26 ◆USING YOUR DISPLAY (continued) ■ Changing the Picture Standard ..................................................................... 26 ■ Adjusting the Picture Settings........................................................................ 27 ■ Adjusting the Picture Settings (PC or DVI Mode).......................................... 28 ■ Setting the Picture (PC Mode)....................................................................... 29 ■ Using the Fine Tune ...................................................................................... 31 ■ Viewing the Channel Scan Picture ................................................................ 32 ■ Freezing the Current Picture ......................................................................... 32 ■ Selecting the Picture Size.............................................................................. 33 ■ Selecting the Film Mode................................................................................ 34 ■ DNIeTM (Digital Natural Image engine ) ............................................... 34 ■ Setting the Blue Screen................................................................................. 35 ■ Setting the Melody Sound ............................................................................. 35 ■ Viewing the Picture In Picture (PIP) .............................................................. 36 ■ Using the Digital NR (Digital Noise Reduction) Feature................................ 38 ■ Changing the Sound Standard ...................................................................... 39 BN68-00597A-01 4/2/04 6:38 PM Page 4

■ Adjusting the Sound Settings ........................................................................ 40 ■ Adjusting the Volume Automatically .............................................................. 40 ■ Setting the TruSurround XT........................................................................... 41 ■ Selecting the Internal mute............................................................................ 41 ■ Selecting the Sound Mode (depending on the model) .................................. 42 ■ Setting the Sleep Timer................................................................................. 43 ■ Setting and Displaying the Current Time....................................................... 44 ■ Switching the Television On and Off Automatically....................................... 45 ■ Viewing an External Signal Source ............................................................... 46 ■ Redirecting an Input to the External Output .................................................. 47 ◆USING THE TELETEXT FEATURE ■ Teletext Feature ............................................................................................ 48 ■ Displaying the Teletext Information ............................................................... 49 ■ Selecting Display Options.............................................................................. 50 ■ Selecting a Teletext Page.............................................................................. 51 ◆USING THE TELEWEB FEATURE (OPTION) ■ TeleWeb Feature........................................................................................... 52 ■ Using the TeleWeb Menu after Displaying the TeleWeb............................... 53 ■ Easy Accessing the TeleWeb Service via the Remote Control..................... 54 ◆ADDITIONAL INFORMATION AND CONNECTIONS ■ Connecting to the External Devices .............................................................. 55 ■ Connecting to the S-Video Input.................................................................... 56 ■ Connecting to the DVI Input .......................................................................... 57 ■ Connecting to the PC Input ........................................................................... 57 ■ Connecting to the Component Input.............................................................. 58 ■ Connecting Additional Speakers ................................................................... 58 ■ Connecting and Using the Home Theater System ........................................ 59 ■ Installing the Speakers .................................................................................. 60 ■ Setting up Your PC Software (Windows only)............................................... 62 ■ Input Mode (PC/DVI) ..................................................................................... 63 ■ Pin Configurations ......................................................................................... 64 ◆RECOMMENDATIONS FOR USE ■ Troubleshooting: Before Contacting Service Personnel................................ 65 ■ Programming the Remote Control for Other Components ............................ 66 ☛ ➢ Press Important Note Symbols BN68-00597A-01 4/2/04 6:38 PM Page 5

Front Panel ➢ The actual configuration on your PDP may be different, depending on your model. a) SOURCE External input selection. b) MENU Menu display. c) - + Volume adjustment. d) C/P. Channel selection. Auto power On. e) Confirm your choice (Store or Enter) f) I / Press to turn the PDP on and off. Speaker BN68-00597A-01 4/2/04 6:38 PM Page 6

ENG ➢ The actual configuration on your PDP may be different, depending on your model. Rear Panel Side of the TV ➢For further details about connection, refer to pages 55~59. Audio Input (L, R) Video Input S-Video Input a) DVI INPUT (DVI-D / L-AUDIO-R) Connect to the digital video and audio output jack for device with DVI output. b) MONITOR OUT (VIDEO / L-AUDIO-R) Outputs for external devices. c) Ext.1, Ext.2, Ext.3 Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players. d) PC INPUT (RGB IN / AUDIO) Connect to the video and audio output jack on your PC. e) ONLY FOR SERVICE Connector for service only. f) AV2, AV3 (S-VIDEO1 or S-VIDEO2 / L-AUDIO-R) Video and audio inputs for external devices with an S-Video output, such as a camcorder or VCR. g) AV1, AV2, AV3 (VIDEO / L-AUDIO-R ) Video and audio inputs for external devices, such as a camcorder or VCR. h) COMPONENT1, COMPONENT2 Video (Y/Pb/Pr) and audio (L-AUDIO-R) inputs for Component. i) ANT IN VHF/UHF (75Ω) 75ΩCoaxial connector for Aerial/Cable Network. j) EXT SPEAKER (8Ω) Connectors for external rear speakers. k) POWER IN Connect the supplied power cord. BN68-00597A-01 4/2/04 6:38 PM Page 7

➢ The performance of the remote control may be affected by bright light. PICTURE EFFECT SELECTION PICTURE SIZE/ TELETEXT SIZE SELECTION MENU DISPLAY/ TELETEXT INDEX TELEWEB DISPLAY (DEPENDING ON THE MODEL) MOVE TO THE REQUIRED MENU OPTION/ ADJUST AN OPTION VALUE RESPECTIVELY TURNS THE PDP ON AND OFF FASTEXT TOPIC SELECTION INFORMATION DISPLAY/ TELETEXT REVEAL TV MODE SELECTION EXIT TELETEXT EXIT TELEWEB (DEPENDING ON THE MODEL) DIRECT CHANNEL SELECTION EXTERNAL INPUT SELECTION/ TELETEXT PAGE HOLD AUTOMATIC SWITCH-OFF/ TELETEXT SUB-PAGE CONFIRM YOUR CHOICE (STORE OR ENTER) NEXT CHANNEL/ TELETEXT NEXT PAGE/ TELEWEB FORWARD SOUND MODE SELECTION IF YOUR REMOTE CONTROL IS NOT FUNCTIONING PROPERLY, TAKE OUT THE BATTERIES AND PRESS THE RESET BUTTON FOR ABOUT 2~3 SECONDS. RE-INSERT THE BATTERIES AND TRY USING THE REMOTE CONTROL AGAIN. TruSurround XT MODE SELECTION PREVIOUS CHANNEL/ TELETEXT PREVIOUS PAGE/ TELEWEB BACKWARD PIP FUNCTIONS; - PIP ACTIVATING OR DEACTIVATING (PIP ON) - SWAPPING THE MAIN AND THE SUB PICTURE (SWAP) - LOCATION SELECTION (POSITION) - SOURCE SELECTION (SOURCE) - SIZE SELECTION (SIZE) - SCAN - SELECTING THE CHANNEL OF SUB PICTURE (P ) MAKE THE REMOTE CONTROL WORKS FOR TV, VCR, CATV, DVD PLAYER, STB SOUND EFFECT SELECTION TELETEXT CANCEL VOLUME INCREASE TEMPORARY SOUND SWITCH-OFF VOLUME DECREASE TELETEXT DISPLAY PICTURE STILL WHEN YOU PRESS A BUTTON , ‘ ’ APPEARS ALONG WITH SELECTED MODE (TV, VCR, CATV, DVD OR STB) AND REMAINING BATTERIES ON LCD VCR/DVD FUNCTIONS; - REWIND (REW) - STOP - PLAY/PAUSE - FAST FORWARD (FF) REMOTE CONTROL SETUP BN68-00597A-01 4/2/04 6:38 PM Page 8

you: ◆Purchase the PDP ◆Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol ( ) downwards and then pulling firmly to remove it. 2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to respect the polarities: ◆ - on the battery against - on the remote control ◆ + on the battery against + on the remote control 3 Replace the cover by aligning it with the base of the remote control and pressing it back into place. Inserting the Batteries in the Remote Control Assembling the Stand-Base 1 Assemble two support pins with the stand base and firmly secure both sides of the support pins using 8 screws provided. 2 Assemble the PDP with the stand and firmly secure the PDP using 4 screws provided. ➢ ◆ Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage to the screen. Always store the PDP upright. The angle of the PDP can be up to 20 degrees left/right. (depending on your model) BN68-00597A-01 4/2/04 6:38 PM Page 9

Wall Mount Bracket Mounting Kits 4 EA 4 EA Plastic Hanger Screws How to Adjust Mounting Angle 1 Secure the PDP to the wall mount bracket. (Please refer to the following instructions.) 2 Set the angle by pulling the upper end of the PDP attached to bracket in the direction of the arrow. 3 The angle can be adjusted from 0° to 15° by ±2°. The wall mount bracket is delivered separately. Please tighten the captive screw in the direction of the arrow after assembling the bracket. Installation Notes ◆ Do not install the PDP on any place other than vertical walls. ◆ To protect the performance of the PDP and prevent troubles, avoid the followings: - Do not install next to smoke and fire detectors. - Do not install in an area subjected to vibration or high voltage. - Do not install near or around any heating apparatus. ◆ Use only recommended parts and components. (depending on your model) BN68-00597A-01 4/2/04 6:38 PM Page 10

1 Remove the screws from the back of the PDP. 3 Tighten the screws of the plastic hanger to the back side of the PDP. 4 Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be separated from wall mount bracket. 2 Use the screws and assemble the plastic hanger. ☛ ◆Please ask the installers to install the wall mount bracket. ◆Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall mount bracket. ◆Please avoid catching your fingers while installing and adjusting the angle. ◆Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP. Connecting External Devices to the PDP 1 Be sure to remove the safety pins underneath the PDP. ◆ If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP. 2 Pull out the bottom of the PDP (which has been attached to the Wall Mount Bracket) in the direction indicated by the arrows (refer to the illustration) until it clicks. ◆ Using the PDP After Connecting External Devices. Be sure to secure the PDP by inserting the 2 safety pins after readjusting the angle of the PDP to 0 o. ◆ For safety, be sure to secure the PDP using the safety pins. If the safety pins are not used, the PDP may fall, causing serious injury. ➢The exterior of the PDP may be different than the picture. (Assembly and installation of the plastic hanger is the same.) ◆ To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions: PDP panel Wall attachment panel bracket Wall BN68-00597A-01 4/2/04 6:38 PM Page 11

network, you must connect a satellite receiver to the rear of the PDP. Also, in order to descramble a coded transmission signal, you must connect a decoder to the rear of the PDP. Using a Coaxial cable Connect a coaxial cable to the: ◆ Receiver (or Decoder) output socket. ◆ Television aerial input socket. ➢ If you wish to connect both a satellite receiver (or decoder) and a VCR, you should connect the: ◆ Receiver (or Decoder) to the VCR ◆ VCR to the PDP Otherwise, connect the receiver (or decoder) directly to the PDP. Connecting a Satellite Receiver or Decoder Rear of the PDP Satellite receiver/ Decoder To view television channels correctly, a signal must be received by the set from one of the following sources: ◆An outdoor aerial ◆A cable television network ◆A satellite network 1 In the first three cases, connect the aerial or network input cable to the 75Ωcoaxial socket on the rear of the PDP. 2 If you are using an indoor aerial, you may need to turn it when tuning your PDP until you obtain a picture that is both sharp and clear. For further details, refer to: ◆ “Storing Channels Automatically” on page 18 ◆ “Storing Channels Manually” on page 19 ➢ When installing or re-installing your PDP, be sure to use the supplied coaxial antenna cable. If you connect using a different coaxial cable, there is risk of noise or interference to the screen image. (You must not use another general purpose cable. Use the 3M/5M/7M cable supplied by Samsung.) Connecting to an Aerial or Cable Television Network Rear of the PDP Cable Television Network or or BN68-00597A-01 4/2/04 6:38 PM Page 12

1 Plug the mains lead into an appropriate socket. Result: The Standby indicator on the front of the PDP lights up. ➢ The main voltage is indicated on the rear of the PDP and the frequency is 50 or 60Hz. 2 Press the “ I / ” button on the front of the PDP (or POWER ( ) button on the remote control) to switch the PDP on. Result: The programme that you were watching last is re- selected automatically. ➣If you have not yet stored any channels, No clear picture appears. Refer to “Storing Channels Automatically” on page 18 or “Storing Channels Manually” on page 19. 3 To switch your PDP off, press the “ I / ” button again. Your PDP can be placed in Standby mode, in order to reduce the Power consumption. The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example). 1 Press the POWER ( ) button on the remote control. Result: The screen is turned off and the Standby indicator on the front of the PDP lights. 2 To switch the PDP back on, simply press the POWER ( ) button again or a numeric button. ➣You can also switch on by pressing the P or button. Switching On and Off Placing in Standby Mode ENG Front of the PDP TV TV BN68-00597A-01 4/2/04 6:38 PM Page 13

The remote control is used mainly to: ◆Change channels and adjust the volume ◆Display the on-screen menu system The following table presents the most frequently used buttons and their functions. Button Viewing Function Menu Function Used to display the next - stored channel. Used to display the - previous stored channel. to Used to display the corresponding channels. ➢For double digit channels, the second digit must be pushed immediately after the first. Failure to do this will result in a single digit channel being displayed. SLEEP Used to select a preset time interval (off - 30 - 60 - 90 - 120 - 150 - 180). Used to increase the - volume. Used to decrease the - volume. MUTE Used to switch the sound off temporarily. ➣To turn the sound back on, press this button again, or press the or button. MENU Used to display the Used to return to the previous on-screen menu system. menu or normal viewing. - Used to: ◆Display a submenu containing selections for the current menu option ◆Increase/decrease a menu option value - Used to confirm your choice. EXIT/TV - Used to exit from the menu system and return to normal viewing directly. BN68-00597A-01 4/2/04 6:38 PM Page 14

top box (STB), in addition to controlling the PDP. ➣ The remote control is not compatible with the TV manufactured by another company. 1 Turn off your VCR, Cable box, DVD or STB. 2 Press the SELECT button. Mode is changed whenever SELECT button is pressed. 3 Press the POWER ( ) button on the remote control. The component you select should turn on. If it turns on, your remote control is now set correctly. 4 Once your remote control is set up, press the SELECT button any time you want to use the remote control to operate your VCR, Cable box, DVD or STB. ➣ When your remote control is in the VCR, CATV, DVD or STB mode, the volume buttons still control your television’s volume. Setting Up Your Remote Control ➢ To program the cable receiver controls: ◆ Press the SELECT button to select CATV. ◆ Point the remote control at the cable receiver and press the SET button. Then press the company code number(s) for the component in page 66. Ex) If the component is manufactured by Oak, press 026. ➢ To program the VCR controls: ◆ Press the SELECT button to select VCR ◆ Point the remote control at the VCR and press the SET button. Then press the company code number(s) for the component in page 67. ➢ To program the DVD controls: ◆ Press the SELECT button to select DVD ◆ Point the remote control at the DVD and press the SET button. Then press the company code number(s) for the component in page 66. ENG VCR BN68-00597A-01 4/2/04 6:38 PM Page 15

settings proceed automatically and subsequently. The following settings are available. 1 If the television is in Standby mode, press the POWER ( ) button on the remote control. Result: The message Plug & Play is displayed. It flickers for a little while, and then the Language menu is automatically displayed. 2 Select the appropriate language by pressing the † or … button. 3 Press the ENTER ( ) button to confirm your choice. Result: The message Antenna Input Check is displayed. 4 Make sure that the antenna is connected to the TV, and then press the ENTER ( ) button. Result: The Country menu is displayed. 5 Select your country by pressing the † or … button. 6 Press the ENTER ( ) button to confirm your choice. Result: The Auto Store menu is displayed. 7 To start the search, press the ENTER ( ) button. Result: The search will end automatically. Channels are sorted and stored in an order which reflects their position in the frequency range (with lowest first and highest last). When it has finished, the Clock Set menu is displayed. ➢ To stop the search before it has finished or return to normal viewing, press the MENU ( ) button. ➢ Press the ENTER ( ) button to set the clock. 8 Press the œ or √button to move to the hour or minute. Set the hour or minute by pressing the † or … button. 9 When it has finished, the message Enjoy Your Watching is displayed, and then the channel which has been stored will be activated. Plug & Play Feature Language Move Enter Austria Belgium Croatia Denmark Finland France Germany ▼ More Country Antenna Input Check Plug & Play Country Press ENTER to Start Plug & Play Start Plug & Play Enter Exit Enjoy Your Watching Press ENTER to start channel memory 40 MHz 0% Start Auto Store Enter Stop Channel store in process. Storing. 57 MHz 1% Auto Store Enter Stop Clock Adjust Move Stop Hour Min 01 00 Stop Move Enter BN68-00597A-01 4/2/04 6:38 PM Page 16

1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Miscellaneous. Press the ENTER ( ) button. Result: The options available in the Miscellaneous group are displayed. 5 Press the † or … button to select Plug & Play. Press the ENTER ( ) button. Result: The message Plug & Play is displayed. 6 For further details on how to set, refer to the opposite page. When you start using your television for the first time, you must select the language which will be used for displaying menus and indications. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button 4 Press the † or … button to select Language. Press the ENTER ( ) button. Result: The languages available are listed. 5 Select the appropriate language by pressing the † or … button. 6 Press the ENTER ( ) button to confirm your choice. 7 When you are satisfied with your choice, press the EXIT/TV ( ) button to return to normal viewing. Plug & Play Feature (continued) Choosing Your Language ENG Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return Melody : Off √ Plug & Play √ Blue Screen : Off √ Miscellaneous Move Enter Return TV TV Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return TV Time Language : English AV Setup Digital NR : On √ Miscellaneous √ PC Setup √ √ Setup Move Enter Return TV BN68-00597A-01 4/2/04 6:38 PM Page 17

depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Country. Press the ENTER ( ) button. Result: The countries available are listed. 5 Select your country (or area) by pressing the † or … button. ➢ If you have selected the Others option but do not wish to scan the PAL frequency range, store the channels manually (see page 19). 6 Press the ENTER ( ) button to confirm your choice 7 Press the † or … button to select Auto Store. Press the ENTER ( ) button. Result: The Auto Store menu is displayed. 8 Press the ENTER ( ) button to start the search. Result: The search will end automatically. Channels are sorted and stored in an order which reflects their position in the frequency range, (with lowest first and highest last). The programme originally selected is then displayed. ➢ To stop the search before it has finished, press the MENU ( ) button. 9 When the channels have been stored, you can: ◆ Sort them in the order required (see page 22) ◆ Clear a channel (see page 21) ◆ Fine-tune channel reception if necessary (see page 31) ◆ Assign a name to the stored channels (see page 23) ◆ Activate/deactivate the Digital Noise Reduction feature (see page 38) Storing Channels Automatically Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV Country : Austria Auto Store Manual Store Edit Fine Tune Ch. Scan Channel Move Enter Return TV Austria Belgium Croatia Denmark Finland France † Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV Channel store in process. Storing. 57 MHz 1% Stop Auto Store Enter Return BN68-00597A-01 4/2/04 6:38 PM Page 18

You can store up to 100 television channels, including those received via cable networks. When storing channels manually, you can choose: ◆Whether or not to store each of the channels found ◆The programme number of each stored channel which you wish to identify 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Manual Store. Press the ENTER ( ) button. Result: The Manual Store menu is displayed. 5 If necessary, select the broadcasting standard required. Press the œ or √button to select Colour System and press the † or … button. The colour standards are displayed in the following order. (depending on the model). Auto - PAL - SECAM or Auto - NT3.58 - NT4.43 - PAL60 6 Press the œ or √button to select Sound System and press the † or … button. The sound standards are displayed in the following order. (depending on the model). BG - DK - I - L Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV Manual Store √ Move Adjust Return Prog. Colour Sound System System 9 Auto BG Channel Search Store C -- 59MHz ? Manual Store œ √ Move Adjust Return Prog. Colour Sound System System 9 Auto BG Channel Search Store C -- 59MHz ? Manual Store œ √ Move Adjust Return Prog. Colour Sound System System 9 Auto BG Channel Search Store C -- 59MHz ? BN68-00597A-01 4/2/04 6:38 PM Page 19

following steps. ◆ Press the œ or √button to select Channel. ◆ Press the † or … button to select C (Air channel) or S (Cable channel). ◆ Press the √button. ◆ Press the numeric buttons (0~9) to select indicate the required number. ➣If no sound or abnormal sound, re-select the sound standard required. 8 If you do not know the channel numbers, select the Search by pressing the œ or √button. Press the † or … button to start the search. Result: The tuner scans the frequency range until the first channel or the channel that you selected is received on your screen. 9 To assign a programme number to a channel, select the Prog. by pressing the œ or √button. Press the † or … button until you find the correct number. 10 To store the channel and associated programme number, select the Store by pressing the œ or √ button. Press the ENTER ( ) button. 11 Repeat Steps 7 to 10 for each channel to be stored. ☛ Channel mode ◆C (Real channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this mode. ◆S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode. Storing Channels Manually (continued) Manual Store œ √ Move Adjust Return Prog. Colour Sound System System 9 Auto BG Channel Search Store C -- 59MHz ? Manual Store œ √ Move Adjust Return Prog. Colour Sound System System 9 Auto BG Channel Search Store C 02 59MHz ? Manual Store œ √ Move Adjust Return Prog. Colour Sound System System 9 Auto BG Channel Search Store C 02 59MHz ? Manual Store œ √ Move Enter Return Prog. Colour Sound System System 9 Auto BG Channel Search Store C 02 59MHz OK BN68-00597A-01 4/2/04 6:38 PM Page 20

You can exclude the channels of your choice from the channel scan operation. When you scan through the stored channels, those that you have chosen to skip are thus not displayed. All channels that you do not specifically choose to skip are displayed during scanning. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Edit. Press the ENTER ( ) button. Result: The Edit menu is displayed. 5 Press the † or … button to select Add/Delete. Press the ENTER ( ) button. Result: The Add/Delete menu is displayed with the current channel automatically is selected. 6 Press the † or … button to select the channel to be deleted. 7 To add or delete the channel, select Added or Deleted by pressing the † or … button. Press the ENTER ( ) button to confirm. Skipping Unwanted Channels Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV Add/Delete √ Sort √ Name √ LNA : Off √ Child Lock √ Edit Move Enter Return TV Add/Delete TV 1 ----- ----- Added 2 ----- ----- Deleted 3 ----- ----- Deleted 4 ----- ----- Deleted 5 ----- ----- Deleted Prog. Move Enter Return Add/Delete TV Prog. Adjust Enter Return 1 ----- ----- Added 2 ----- ----- Deleted 3 ----- ----- Deleted 4 ----- ----- Deleted 5 ----- ----- Deleted BN68-00597A-01 4/2/04 6:38 PM Page 21

stored channels. This operation may be necessary after using ATM. You can delete those channels you do not want to keep. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Edit. Press the ENTER ( ) button. Result: The Edit menu is displayed. 5 Press the † or … button to select Sort. Press the ENTER ( ) button. Result: The Sort menu is displayed. 6 Select the channel that you wish to move by pressing the † or … button. Press the ENTER ( ) button. 7 Select the number of the programme to which the channel is to be moved by pressing the † or … button. Press the ENTER ( ) button. Result: The channel is moved to its new position and all other channels are shifted accordingly. 8 Repeat Steps 6 to 7 until you have moved all the channels to the required programme numbers. Sorting the Stored Channels Sort TV Sort TV Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV Add/Delete √ Sort √ Name √ LNA : Off √ Child Lock √ Edit Move Enter Return Move Enter Return Move Enter Return TV Prog. 2 ----- ----- ----- ----- 3 ----- ----- 4 ----- ----- 5 ----- ----- 6 ----- ----- Prog. 2 ----- ----- 3 ----- ----- 4 ----- ----- 5 ----- ----- 6 ----- ----- BN68-00597A-01 4/2/04 6:38 PM Page 22

information is broadcast. These names can be changed, allowing you to assign new names. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Edit. Press the ENTER ( ) button. Result: The Edit menu is displayed. 5 Press the † or … button to select Name. Press the ENTER ( ) button. Result: The Name menu is displayed with the current channel automatically is selected. 6 If necessary, select the channel to be assigned a new name by pressing the † or … button. Press the ENTER ( ) button. Result: Arrow indications are displayed around the name box. 7 Press the † or … button to select a letter (A~Z), a number (0~9) or a symbol (-, space). Move on the previous or next letter by pressing the œ or √button. 8 When you have finished entering the name, press the ENTER ( ) button to confirm the name. Assigning Names to Channels Name TV Prog. Name Name TV 2 ----- ----- 3 ----- ----- 4 ----- ----- 5 ----- ----- 6 ----- ----- Prog. Name Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV Add/Delete √ Sort √ Name √ LNA : Off √ Child Lock √ Edit Move Enter Return Move Enter Return Adjust Enter Return TV 2 ----- ----- 3 ----- ----- 4 ----- ----- 5 ----- ----- 6 ----- ----- BN68-00597A-01 4/2/04 6:38 PM Page 23

weak signal. LNA amplifies the TV signal in the weak signal area, but not noise. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Edit. Press the ENTER ( ) button. Result: The Edit menu is displayed. 5 Press the † or … button to select LNA. Press the ENTER ( ) button. Result: The options available are listed. 6 Select On or Off by pressing the † or … button. Press the ENTER ( ) button to confirm. ➢ ◆ If the picture is noisy with the LNA set to On, select Off. ◆ LNA setting is to be made for each channel. Using the LNA (Low Noise Amplifier) Feature Off On BN68-00597A-01 4/2/04 6:38 PM Page 24

This feature allows you to lock the television so that it cannot be switched on via the front panel. It can, however, still be switched on via the remote control. Thus, by keeping the remote control away from unauthorised users, such as children, you can prevent them from watching unsuitable programme. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Edit. Press the ENTER ( ) button. Result: The Edit menu is displayed. 5 Press the † or … button to select Child Lock. Press the ENTER ( ) button. Result: The Child Lock menu is displayed with the current channel automatically is selected. Blue Screen is displayed when the Child Lock is activated. 6 Press the † or … button to select the channel to be locked. 7 Press the ENTER ( ) button. To lock the channel, select Locked by pressing the † or … button (to unlock the channel, select Unlocked). Press the ENTER ( ) button to confirm. Activating the Child Lock Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV Add/Delete √ Sort √ Name √ LNA : Off √ Child Lock √ Edit Move Enter Return TV Child Lock TV 2 ----- ----- Unlocked 3 ----- ----- Unlocked 4 ----- ----- Unlocked 5 ----- ----- Unlocked 6 ----- ----- Unlocked Prog. Child Lock TV Prog. Move Enter Return Adjust Enter Return 2 ----- ----- Unlocked 3 ----- ----- Unlocked 4 ----- ----- Unlocked 5 ----- ----- Unlocked 6 ----- ----- Unlocked BN68-00597A-01 4/2/04 6:38 PM Page 25

viewing requirements. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Picture. Result: The options available in the Picture group are displayed. 3 Press the ENTER ( ) button. Result: The Mode is selected. 4 Press the ENTER ( ) button again. Result: The options available are listed. 5 Select the option by pressing the † or … button. Result: The following modes are available depending on the input source. ◆ Dynamic - Standard - Movie - Custom ◆ High - Middle - Low - Custom (PC or DVI Mode). 6 Press the ENTER ( ) button to confirm. ➣ You can also set these options simply by pressing the P.MODE ( : Picture Mode) button. Changing the Picture Standard You can view the channel information and setting status you select by pressing the “INFO ( )” button on the remote control. P 1 ✽ Picture : Dynamic Sound : Music 00 : 00 Mono Mode : Dynamic √ Custom √ Colour Tone : Normal √ Colour Control √ Film Mode : Off √ Size : 16 : 9 √ DNIe : On √ PIP √ Picture Move Enter Return TV Mode : Dynamic Custom Colour Tone : Normal Colour Control Film Mode : Off Size : 16 : 9 DNIe : On PIP Picture Move Enter Return TV Dynamic Standard Movie Custom BN68-00597A-01 4/2/04 6:38 PM Page 26

picture quality. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Picture. Result: The options available in the Picture group are displayed. 3 Press the ENTER ( ) button. 4 Select the required option (Custom, Colour Tone) pressing the † or … button. 5 Press the † or … button to select Custom. Press the ENTER ( ) button. Result: The Custom menu is displayed. 6 Press the ENTER ( ) button to change the setting. The options are displayed in the following order. ◆ Custom : Contrast, Brightness, Sharpness, Colour, Tint(NTSC ONLY) ➣Custom Options available in PC, DVI Mode: Contrast, Brightness, Sharpness. ➣The horizontal bar is displayed. Move the horizontal bar’s cursor left or right by pressing the œ or √button. ➣When the picture mode is set to Custom, the settings values may vary depending on the input source. (ex. RF, Video, Component, PC or DVI) ➣If you make any changes to these settings, the picture standard is automatically switched to the Custom. ◆ Colour Tone : Cool2, Cool1, Normal, Warm1, Warm2 7 When you are satisfied with the settings, press the EXIT/TV ( ) button to return to normal viewing. ➣ If you make any changes to these settings, the picture standard is automatically switched to the Custom. Adjusting the Picture Settings Custom TV Contrast 70 Brightness 50 Sharpness 70 Colour 50 Tint G50 R50 Contrast 70 Mode : Dynamic √ Custom √ Colour Tone : Normal √ Colour Control √ Film Mode : Off √ Size : 16 : 9 √ DNIe : On √ PIP √ Picture Move Enter Return TV Move Enter Return Mode : Dynamic Custom Colour Tone : Normal Colour Control Film Mode : Off Size : 16 : 9 DNIe : On PIP Picture Move Enter Return TV Cool2 Cool1 Normal Warm1 Warm2 BN68-00597A-01 4/2/04 6:38 PM Page 27

Result: The main menu is displayed. 2 Press the † or … button to select Picture. Result: The options available in the Picture group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Custom. Press the ENTER ( ) button. Result: The Custom menu is displayed. 5 Press the † or … button to select the option (Contrast, Brightness, Sharpness) to be adjusted. Press the ENTER ( ) button. Result: The horizontal bar is displayed. Move the horizontal bar’s cursor left or right by pressing the œ or √button. 6 Press the MENU button to confirm your choice. 7 Press the MENU button. Result: The options available in the Picture group are displayed again. 8 Press the † or … button to select Colour Tone. Press the ENTER ( ) button. 9 Select the option by pressing the † or … button. The colour tones are displayed in the following order. Custom (PC mode only) - Colour1 - Colour2 - Colour3 10 Press the MENU button. Result: The options available in the Picture group are displayed again. 11 Press the † or … button to select Colour Control. Press the ENTER ( ) button. Result: The Colour Control menu is displayed. 12 Press the † or … button to select the option (R, G, B) to be adjusted. Press the ENTER ( ) button. Result: The horizontal bar is displayed. Move the horizontal bar’s cursor left or right by pressing the œ or √button. ➣ The Colour Control is not available in the DVI Mode. Adjusting the Picture Settings (PC or DVI Mode) ➢Preset to the PC or DVI mode by using the SOURCE button. Custom TV Contrast 70 Brightness 50 Sharpness 70 Colour 50 Tint G50 R50 Mode : High √ Custom √ Colour Tone : Custom √ Colour Control √ Film Mode : Off √ Size : 16 : 9 √ DNIe : On √ PIP √ Picture Move Enter Return TV Move Enter Return Mode : High Custom Colour Tone : Normal Colour Control Film Mode : Off Size : 16 : 9 DNIe : On PIP Picture Move Enter Return TV Custom Colour1 Colour2 Colour3 Colour Control TV R 70 G 50 B 70 Move Enter Return BN68-00597A-01 4/2/04 6:38 PM Page 28

Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select PC Setup. Press the ENTER ( ) button. Result: The options available in the PC Setup group are displayed. 5 Press the † or … button to select Image Lock. Press the ENTER ( ) button. Result: The options available in the Image Lock group are displayed. 6 Press the † or … button to select the option (Coarse, Fine) to be adjusted. Press the ENTER ( ) button. Result: The horizontal bar is displayed. Move the horizontal bar’s cursor left or right by pressing the œ or √button. 7 Press the MENU ( ) button to confirm your choice 8 Press the MENU button. Result: The options available in the PC Setup group are displayed again. 9 Press the † or … button to select Position. Press the ENTER ( ) button. Result: The options available in the Position group are displayed. 10 Adjust the position by using the †, …, œ, or √button. 11 Press the MENU ( ) button to confirm your choice Setting the Picture (PC Mode) ➢Preset to the PC mode by using the SOURCE button. Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return TV Image Lock √ Position √ Information √ Auto Adjustment √ PC Setup Move Enter Return TV Coarse 50 Fine 20 Image Lock Move Enter Return TV Coarse 50 Image Lock √ Position √ Information √ Auto Adjustment √ PC Setup Move Enter Return TV Position Move œ √ Move Return TV BN68-00597A-01 4/2/04 6:38 PM Page 29

➢Preset to the PC mode by using the SOURCE button. 12 If you get the PC information, select the Information by pressing the † or … button. Press the ENTER ( ) button. Result: The resolution, horizontal and vertical frequency are displayed. 13 Press the MENU button. Result: The options available in the PC Setup group are displayed again. 14 Press the † or … button to select Auto Adjustment. Press the ENTER ( ) button. Result: The screen quality and position are automatically reset with the Auto Adjusting displayed. 15 When you are satisfied with the settings, press the MENU ( ) button repeatedly to return to the normal viewing. Resolution : 1024 ✻768 H-Frequency : 48.5KHz V-Frequency : 60.2Hz Information Return TV Image Lock √ Position √ Information √ Auto Adjustment √ PC Setup Move Enter Return TV Auto Adjusting Auto Adjustment TV BN68-00597A-01 4/2/04 6:38 PM Page 30

If reception is weak, you can fine tune a channel manually. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Fine tune. Press the ENTER ( ) button. Result: The horizontal bar is displayed. Move the horizontal bar’s cursor left or right by pressing the œ or √button to reach the required setting. 5 Press the œ or √button until the picture and sound are both clear and sharp. ➣If you are unable to fine tune a channel, check that the Colour System and Sound System settings are correct. ➣Fine tune Store will change the colour of the Channel OSD(On Screen Display) from White to Red. P 1 0 Fine Tune Reset Return Move œ √ Adjust Store Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV P 1 3 Fine Tune Reset Return Move œ √ Adjust Store Fine Tune P 1 is fine tuned 3 Reset Return Move œ √ Adjust Store P1 C11 BN68-00597A-01 4/2/04 6:38 PM Page 31

1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Channel. Result: The options available in the Channel group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Ch. Scan. Press the ENTER ( ) button. Result: You can view every memorized channel in order. ➣ When PIP ON is activated, the PIP will appear in Large mode and PIP channel will be scanned. P 1 ✽ Ch. Scan Return You can freeze the picture when watching a television programme simply by pressing the “STILL” button. To return to normal viewing, press it again. ➣ In the PIP mode, the main and sub pictures are stilled at the same time. Freezing the Current Picture Country : Austria √ Auto Store √ Manual Store √ Edit √ Fine Tune √ Ch. Scan √ Channel Move Enter Return TV BN68-00597A-01 4/2/04 6:38 PM Page 32

You can select the picture size which best corresponds to your viewing requirements. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Picture. Result: The options available in the Picture group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button until the Size is selected. Press the ENTER ( ) button 5 Press the † or … button to change the setting. ◆ Auto Wide : Expanding and pulling up the picture from 4:3 to 16:9 ratio. ◆ 16:9 : Sets the picture to 16:9 wide mode. ◆ Panorama : Use this mode for the wide aspect ratio of a panoramic picture. ◆ Zoom : Magnify the size of the picture vertically on screen. ◆ 14:9 : Magnify the size of the picture more than 4:3. ◆ 4:3 : Sets the picture to 4:3 normal mode. 6 Press the ENTER ( ) button to confirm. ➣ ◆You can select these options by simply pressing the P.SIZE button on the remote control. ◆The picture size can not be changed in the PIP mode. ◆Depending on the input source, the P.SIZE options may vary. Positioning and Sizing the screen using Zoom ➣ ◆Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction using the † or … button as well as the screen size. ◆Move the screen up/down using the † or … button after selecting the by pressing the † or … button. ◆Resize the screen vertically using the † or … button after selecting the by pressing the † or … button. ◆Screen enlargement operates only in TV/Video/ S-Video/Component1,2 input modes. ◆PC/DVI modes prevents the screen enlargement function. Size Move Enter Return TV Mode : Dynamic √ Custom √ Colour Tone : Normal √ Colour Control √ Film Mode : Off √ Size : 16 : 9 √ DNIe : On √ PIP √ Auto Wide 16:9 Panorama Zoom 14:9 4:3 Picture Move Enter Return TV PC to DVI Mode Size Move Enter Return TV Auto Wide 16:9 Panorama Zoom 14:9 4:3 BN68-00597A-01 4/2/04 6:38 PM Page 33

enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, much detailed image to you. DNIeTM technology will fit every signals into your eyes. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button until the Picture is selected. Result: The options available in the Picture group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button until the DNIe is selected. Press the ENTER ( ) button. 5 Press the † or … button to change the setting. ◆ On: Switches on the DNIe mode. ◆ Off: Switches off the DNIe mode. ◆ Demo (Option): The screen before applying DNIe appears on the right and the screen after applying DNIe appears on the left. DNIeTM (Digital Natural Image engine) Mode : Dynamic √ Custom √ Colour Tone : Normal √ Colour Control √ Film Mode : Off √ Size : 16 : 9 √ DNIe : On √ PIP √ Picture Move Enter Return TV Mode : Dynamic Custom Colour Tone : Normal Colour Control Film Mode : Off Size : 16 : 9 DNIe : On PIP Picture Move Enter Return TV On Off Demo You can automatically sense and process film signals from some sources and adjust the picture for optimum quality. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Picture. Result: The options available in the Picture group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Film Mode. Press the ENTER ( ) button. 5 Press the † or … button to change the setting. (Off or On). ◆ On : Automatically senses and processes film signals from some sources and adjusts the picture for optimum quality. ◆ Off : Switches off the Film Mode. ➢ ◆Not available in the PC, Component (480p, 576p, 720p, 1080i) or DVI modes. ◆Mode discrepancies, such as turning off Film Mode while viewing a film source or turning on Film Mode while viewing non-film sources, may affect the picture quality. Selecting the Film Mode Mode : Dynamic √ Custom √ Colour Tone : Normal √ Colour Control √ Film Mode : Off √ Size : 16 : 9 √ DNIe : On √ PIP √ Picture Move Enter Return TV Mode : Dynamic Custom Colour Tone : Normal Colour Control Film Mode : Off Size : 16 : 9 DNIe : On PIP Picture Move Enter Return TV Off On BN68-00597A-01 4/2/04 6:38 PM Page 34

automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the “Blue Screen“ mode to “Off“. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Miscellaneous. Press the ENTER ( ) button. Result: The options available in the Miscellaneous group are displayed. 5 Press the † or … button to select Blue Screen. Press the ENTER ( ) button. 6 Press the † or … button to change the setting. (On or Off). ➣ ◆ Blue Screen is displayed while no signal from the external device in the External Mode, regardless of the Blue Screen Setting. Setting the Blue Screen Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return Melody : Off √ Plug & Play √ Blue Screen : Off √ Miscellaneous Move Enter Return TV You can hear clear melody sound when the television is powered on or off. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Miscellaneous. Press the ENTER ( ) button. Result: The options available in the Miscellaneous group are displayed. 5 Press the † or … button to select Melody. Press the ENTER ( ) button. 6 Select the option (Off or On). Setting the Melody Sound TV Melody : Off √ Plug & Play √ Blue Screen : Off √ Miscellaneous Move Enter Return TV Melody : Off Plug & Play Blue Screen : Off Miscellaneous Move Enter Return TV Off On Melody : Off Plug & Play Blue Screen : Off Miscellaneous Move Enter Return TV Off On BN68-00597A-01 4/2/04 6:38 PM Page 35

program or external A/V devices. In this way you can watch TV program or monitor the video input from any connected devices while watching TV or other video input. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Picture. Result: The options available in the Picture group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select PIP. Press the ENTER ( ) button. Result: The options available in the PIP group are displayed. 5 To activate, set the PIP to on by pressing the † or … button. 6 Press the † or … button to select Source. Select a source of the sub picture by pressing the ENTER ( ) button. Result: The sources are displayed in the following order: TV - Ext.1 - Ext.2 - Ext.3 - AV1 - AV2 - AV3 - S-Video1 - S-Video2 - Component1 - Component2 - PC - DVI ➣ ◆The PC can not be selected in DVI mode. ◆The DVI can not be selected in PC mode. 7 Press the † or … button to select Swap. Press the ENTER ( ) button. Result: The main picture and sub picture are interchanged. 8 Press the † or … button to select Size. Select a size of the sub picture by pressing the ENTER ( ) button. Result: The sizes are displayed in the following order: (Large) - (Small) - (Double1) - (Double2) ➣ The Double1 or Double2 mode can not be selected in PC or DVI mode. Table of PIP Settings Viewing the Picture In Picture (PIP) PIP PIP : On Source : TV Swap Size : Position : Prog. : P 8 TV Off On Mode : Dynamic √ Custom √ Colour Tone : Normal √ Colour Control √ Film Mode : Off √ Size : 16 : 9 √ DNIe : On √ PIP √ Picture Move Enter Return Move Enter Return TV PIP PIP : On Source : TV Swap Size : Position : Prog. : P08 TV Move Enter Return TV Ext.1 Ext.2 Ext.3 AV1 AV2 † PIP PIP : On √ Source : TV √ Swap √ Size : √ Position : √ Prog. : P 8 √ TV Move Enter Return PIP PIP : On Source : TV Swap Size : Position : Prog. : P08 TV Move Enter Return TV Ext.1 Ext.2 Ext.3 AV1 AV2 AV3 S-Video1 S-Video2 COMP1 COMP2 PC DVI TV O O O O O O O O O O O O O Ext.1 O X O O O O O O O O O O O Ext.2 O O X O O O O O O O O O O Ext.3 O O O X O O O O O O O O O AV1 O O O O X O O O O O O O O AV2 O O O O O X O O O O O O O AV3 O O O O O O X O O O O O O S-Video1 O O O O O O O X O O O O O S-Video2 O O O O O O O O X O O O O COMP1 O O O O O O O O O X X X X COMP2 O O O O O O O O O X X X X PC O O O O O O O O O X X X X DVI O O O O O O O O O X X X X BN68-00597A-01 4/2/04 6:38 PM Page 36

( ) button. Result: The positions available are displayed. - - - 10 Press the † or … button to select Prog.. Select the channel that you want to view through sub picture by pressing the ENTER ( ) button. ➣ If the sub picture is no signal and the main picture is output from a Component, PC or DVI signal, the sub picture will be blue. If the main picture is output from a Video signal, the sub picture will be black. Easy functions of remote control. Buttons Feature PIP ON Used to activate or deactivate the PIP function directly. SWAP Used to interchange the main picture and the sub picture. ➣When the main picture is in the Video mode and the sub picture is in the TV mode, you might not hear the sound of main picture when pressing the SWAP ( ) button after changing the sub picture channel. At this time, reselect the channel of main picture. POSITION Used to move the sub picture counterclockwise. SOURCE Used to assign a source of sub picture (TV, Ext.1, Ext.2, Ext.3, AV1, AV2, AV3, S-Video1, S-Video2, Component1, Component2, PC, DVI). SIZE Used to select a size of sub picture (Large, Small, Double1, Double2). SCAN Used to scan every memorized channel in order. To stop scanning, press it again. P / Used to select the channel of sub picture. Viewing the Picture In Picture (PIP) (continued) PIP PIP : On Source : TV Swap Size : Position : Prog. : P08 TV Move Enter Return PIP PIP : On Source : TV Swap Size : Position : Prog. : P08 TV Move Enter Return TV P 1 BN68-00597A-01 4/2/04 6:38 PM Page 37

If the signal received by your television is weak, you can activate this feature to help reduce any static and ghosting that may appear on the screen. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the ▲or ▼button until the Setup is selected. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the ▲or ▼button until the Digital NR is selected. Press the ENTER ( ) button. 5 Select Off or On by pressing the ▲or ▼button. Press the ENTER ( ) button to confirm. Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return TV Time Language : English AV Setup Digital NR : On Miscellaneous PC Setup Setup Move Enter Return TV Off On BN68-00597A-01 4/2/04 6:38 PM Page 38

You can select the type of special sound effect to be used when watching a given broadcast. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Sound. Result: The options available in the Sound group are displayed. 3 Press the ENTER ( ) button. Result: The Mode is selected. 4 Press the ENTER ( ) button again. 5 Select the option by pressing the † or … button. The sound effects are displayed in the following order. Standard - Music - Movie - Speech - Custom. 6 Press the ENTER ( ) button to confirm. ➣ You can also set these options simply by pressing the S.MODE ( : Sound Mode) button. Mode : Standard √ Equalizer √ Auto Volume : Off √ SRS TSXT : Off √ Internal Mute : Off √ Sound Move Enter Return TV Mode : Standard Equalizer Auto Volume : Off SRS TSXT : Off Internal Mute : Off Sound Move Enter Return TV Standard Music Movie Speech Custom BN68-00597A-01 4/2/04 6:38 PM Page 39

is not easy for you to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Sound. Result: The options available in the Sound group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Auto Volume. Press the ENTER ( ) button. 5 Select the option (Off or On) by pressing the † or … button. Adjusting the Volume Automatically Mode : Standard √ Equalizer √ Auto Volume : Off √ SRS TSXT : Off √ Internal Mute : Off √ Sound Move Enter Return Mode : Standard Equalizer Auto Volume : Off SRS TSXT : Off Internal Mute : Off Sound Move Enter Return TV Off On The sound settings can be adjusted to suit your personal preferences. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Sound. Result: The options available in the Sound group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Equalizer. Press the ENTER ( ) button. Result: The Equalizer menu is displayed with the current option. 5 Select the option (volume, balance, equalizer) to be adjusted by pressing the œ or √button. Press the † or … button to reach the required setting. 6 When you are satisfied with the settings, press the MENU ( ) button to store them. ➣ If you make any changes to the equalizer settings, the sound standard is automatically switched to the Custom. Adjusting the Sound Settings Mode : Standard √ Equalizer √ Auto Volume : Off √ SRS TSXT : Off √ Internal Mute : Off √ Sound Move Enter Return TV Equalizer TV 100 300 1K 3K 10K R L 0 Adjust √Move Return TV BN68-00597A-01 4/2/04 6:38 PM Page 40

problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button until the Sound is selected. Result: The options available in the Sound group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button until the SRS TSXT is selected. Press the ENTER ( ) button. 5 Press the † or … button to change the setting. (Off, 3D Mono or Stereo). ➢ TruSurround XT, SRS and ( ) Symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. ➣ You can also set these options simply by pressing the SRS TSXT ( )button. Setting the TruSurround XT Mode : Standard √ Equalizer √ Auto Volume : Off √ SRS TSXT : Off √ Internal Mute : Off √ Sound Move Enter Return TV Mode : Standard Equalizer Auto Volume : Off SRS TSXT : Off Internal Mute : Off Sound Move Enter Return TV Off 3D Mono Stereo Since the speakers are built in the PDP, you can hear the sound without connecting separate speakers. If you want to hear the sound through separate speakers, cancel the internal amplifier. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Sound. Result: The options available in the Sound group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Internal Mute. Press the ENTER ( ) button. 5 Press the † or … button to change the setting. (On or Off). Selecting the Internal Mute Mode : Standard √ Equalizer √ Auto Volume : Off √ SRS TSXT : Off √ Internal Mute : Off √ Sound Move Enter Return TV Mode : Standard Equalizer Auto Volume : Off SRS TSXT : Off Internal Mute : Off Sound Move Enter Return TV Off On BN68-00597A-01 4/2/04 6:38 PM Page 41

of the audio signal. When power is switched on, the mode is automatically preset to either “DUAL-I ” or “Stereo”, depending on the current transmission. ➣ ◆If the receiving conditions deteriorate, listening will be easier if the mode is set to the Mono. ◆If the stereo signal is weak and an automatic switching occurs, then switch to the Mono. ◆When receiving a mono sound in the AV mode, connect to the “AUDIO-L” input connector on the side of the television. If the mono sound comes out only from left speaker, press the DUAL I-II button. Type of broadcast Regular broadcast (Standard audio) Regular + NICAM Mono NICAM Stereo NICAM DUAL-I/II Regular broadcast (Standard audio) Bilingual or DUAL-I/II Stereo On-screen indication Mono (Normal use) NICAM Mono ↔Mono NICAM Stereo ↔Mono (Forced mono) Mono DUAL-I ↔DUAL-II Stereo ↔Mono (Forced mono) NICAM DUAL-I→ NICAM DUAL-II → Mono NICAM Stereo A2 Stereo Selecting the Sound Mode (depending on the model) BN68-00597A-01 4/2/04 6:38 PM Page 42

You can select a time period of between 30 and 180 minutes after which the television automatically switches to Standby mode. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Time. Press the ENTER ( ) button. Result: The options available in the Time group are displayed. 5 Press the † or … button to select Sleep Timer. Press the ENTER ( ) button. Result: The Sleep Timer menu is displayed with the Min is selected. 6 Select the preset time intervals (Off, 30, 60, 90, 120, 150, 180) by pressing the † or … button. 7 When you are satisfied with the settings, select Activation to Yes or No by pressing the † or … button. 8 Press the ENTER ( ) button to confirm your selection. ➣◆ You can also set these options simply by pressing the SLEEP button. ◆ If the sleep timer is not yet set, Off is displayed. If the sleep timer is already set, the remaining time before which the television switches to Standby mode is displayed. Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return TV Clock 00 : 00 √ Sleep Timer Off √ On Timer Off √ Off Timer Off √ Time Move Enter Return TV Sleep Timer Adjust √Move Return TV Min Activation -- No Sleep Timer Adjust œ √Move Return TV Min Activation 30 Yes Off BN68-00597A-01 4/2/04 6:38 PM Page 43

√ Sleep Timer Off √ On Timer Off √ Off Timer Off √ Time Move Enter Return TV Clock Adjust √Move Return TV Hour Min 00 00 You can set the television’s clock so that the current time is displayed by pressing the “INFO ( )” button. You must also set the time if you wish to use the automatic on or off timers. ➣ When pressing the “I / ” button (On/Off) on the front of the television, the clock setting will be reset. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the ▼or ▲button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the ▼or ▲button to select Time. Press the ENTER ( ) button. Result: The options available in the Time group are displayed with Clock is selected. 5 Press the ENTER ( ) button. 6 Press the ¦ or ‹
button to move to the hour or minute. Set the hour or minute by pressing the ▼or ▲button. 7 When you have finished, press the MENU ( ) button to exit. 8 Press the INFO ( ) button to display the current time. Setting and Displaying the Current Time BN68-00597A-01 4/2/04 6:38 PM Page 44

Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return TV Clock 00 : 00 √ Sleep Timer Off √ On Timer Off √ Off Timer Off √ Time Move Enter Return TV On Timer Adjust √Move Return TV Hour Min Prog. 00 00 1 Volume Activation 10 No Off Timer Adjust √Move Return TV Hour Min 00 00 Activation No You can set the television’s clock and set the On or Off timers so that the television will: ◆Switch on automatically and tune to the channel of your choice at the time you select ◆Switch off automatically at the time you select ➣ The first step is to set the television’s clock (refer to “Setting and Displaying the Current Time” on the previous page). 1 Press the MENU button. Result: The main menu is displayed. 2 Press the ▼or ▲button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select Time. Press the ENTER ( ) button. Result: The options available in the Time group are displayed. 5 Press the ▼or ▲button to select On Timer. Press the ENTER ( ) button. Result: The options available in the On Timer group are displayed. 6 Select the Hour, Min, Prog., Volume by pressing the œ or √ button. Set these by pressing the † or … button. 7 When you are satisfied with the settings, select Activation to Yes or No by pressing the † or … button. 8 Press the MENU button. Result: The options available in the Time group are displayed again. 9 Press the † or … button to select Off Timer. Press the ENTER ( ) button. Result: The Off Timer menu is displayed. 10 Select the Hour, Min or Activation by pressing the œ or √ button. Set these by pressing the † or … button. ➣ Absent Power Off When you set the timer “On”, your television will eventually be turned off, if you do not operate any controls during the 3 hours after the TV is turned on by timer. This function is available in only the timer “On” mode and will prevent a leakage accident or overheating, caused by your TV left on for a long time due to the timer “On” (when you are away on holiday, for example). BN68-00597A-01 4/2/04 6:38 PM Page 45

Use the remote control to switch between viewing signal from connected equipment, such as VCR, DVD, Set-Top-boxs and the TV source (broadcast or cable) 1 Press the MENU button. Result: The main menu is displayed. 2 Press the ▼or ▲button to select Input. Result: The options available in the Input group are displayed. 3 Press the ENTER ( ) button. 4 Press the ▼or ▲button to select Source List. Press the ENTER ( ) button. Result: The options available in the Source List group are displayed. 5 Press the ▼or ▲button to select signal source, then press the ENTER ( ) button. ➢ When you connect equipment to the TV, you can choose between the following sets of jacks : Ext.1, Ext.2, Ext.3, AV1, AV2, AV3, S-Video1, S-Video2, Component1, Component2, PC or DVI on the TV’s rear panel. 6 Press the MENU button and select Input. 7 Press the ▼or ▲button to select Edit Name. Press the ENTER ( ) button. Result: The options available in the Edit Name group are displayed. 8 Press the ▼or ▲button to select external device : Ext.1 - Ext.2 - Ext.3 - AV1 - AV2 - AV3 - S-Video1 - S-Video2 - Component1 - Component2 - PC - DVI 9 Press the ENTER ( ) button. Result: The Edit Name available are listed. 10 Select the name by pressing the † or … button. Press the ENTER ( ) button. 11 Set other signal sources (VCR, DVD, Cable STB, HD STB, Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR or PC) using the same method as listed above. ➣ You can also set these options simply by pressing the SOURCE ( ) button. If you change the external source while viewing, pictures might take a short period of time to be switched. ➣ DHR : DVD HDD Recorder Source List : TV √ Edit Name √ Input Move Enter Return TV Source List : TV √ Edit Name √ Input Move Enter Return TV TV Ext.1 - - - - Ext.2 - - - - Ext.3 - - - - AV1 - - - - AV2 - - - - AV3 - - - - ▼ More Source List Move Enter Return TV Ext.1 : - - - - Ext.2 : - - - - Ext.3 : AV1 : AV2 : AV3 : S-Video1 : - - - - ▼ More Edit Name Move Enter Return TV - - - - VCR DVD Cable STB HD STB Satellite STB † BN68-00597A-01 4/2/04 6:39 PM Page 46

Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ Setup Move Enter Return TV Ext.1 : TV √ Ext.2 : TV √ Ext.3 : TV √ AV Setup Move Enter Return TV Ext.1 : TV Ext.2 : TV Ext.3 : TV AV Setup Move Enter Return TV TV Ext.1 Ext.2 Ext.3 AV1 AV2 † Your television enables you to choose which audio/video signals are output to the external connector. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select AV Setup. Press the ENTER ( ) button. Result: The AV Setup menu is displayed. 5 Press the † or … button to select required input (Ext.2 or Ext.3). Select the source to be directed to the output by pressing the † or … button. 6 Press the ENTER ( ) button to confirm the change. BN68-00597A-01 4/2/04 6:39 PM Page 47

teletext. Information provided includes: ◆ Television programme times ◆ News bulletins and weather forecasts ◆ Sports results ◆ Travel information This information is divided into numbered pages (see diagram). Part Contents A Selected page number. B Broadcasting channel identity. C Current page number or search indications. D Date and time. E Text. F Status information. FASTEXT information. ➣ Teletext information is often divided between several pages displayed in sequence, which can be accessed by: ◆Entering the page number ◆Selecting a title in a list ◆Selecting a coloured heading (FASTEXT system) 48 ENG Teletext Feature BN68-00597A-01 4/2/04 6:39 PM Page 48

You can display Teletext information at any time on your television ☛For Teletext information to be displayed correctly, channel reception must be stable; otherwise: ◆Information may be missing ◆Some pages may not be displayed 1 Select the channel providing the Teletext service by pressing the P or button. 2 Press the TTX/MIX ( ) button to activate the teletext mode. Result: The contents page is displayed. It can be redisplayed at any time by pressing the (index) button. 3 Press the TTX/MIX ( ) button again. Result: The screen will be split into two. This Double Teletext feature lets you view the actual broadcast and teletext information separately on the screen. 4 If you wish to display the actual broadcast and teletext information on a single screen, press the TTX/MIX ( ) button again. 5 To exit from the teletext display, press the EXIT/TV ( ) button. BN68-00597A-01 4/2/04 6:39 PM Page 49

options to suit your requirements. To display... Press the... ◆ Hidden text (reveal) (answers to quiz games, for example) ◆ The normal screen (reveal) again ◆ A secondary page by entering its number (sub-page) ◆ The broadcast when searching for a page (cancel) ◆ The next page (page up) ◆ The previous page (page down) ◆ Double-size letters in the: (size) • Upper half of the screen • Once • Lower half of the screen • Twice ◆ The normal screen • Three times Selecting Display Options TV BN68-00597A-01 4/2/04 6:39 PM Page 50

You can enter the page number directly by pressing the numeric buttons on the remote control. 1 Enter the three-digit page number given in the content by pressing the corresponding numeric buttons. Result: The current page counter is incremented and the page is then displayed. If the selected page is linked with several secondary pages, the secondary pages are displayed in sequence. 2 If the FASTEXT system is used by the broadcasting company, the different topics covered on a Teletext page are colour-coded and can be selected by pressing the coloured buttons on the remote control. Press the coloured button corresponding to the topic that you wish to select; the available topics are given on the status line. Result: The page is displayed with other coloured information that can be selected in the same way. 3 To display the previous or next page, press the corresponding coloured button. 4 To display the subpage, see the following steps. ◆ Press the (sub-page) button. Result: The available subpages appear. ◆ Select the required sub-page. Sub-pages can be scrolled by pressing the or button. 5 When you have finished, press the EXIT/TV ( ) button to return to your normal broadcast. BN68-00597A-01 4/2/04 6:39 PM Page 51

services. TeleWeb is similar to Teletext, just easy to use. TeleWeb can transmit the News, TV programme information, and advertising in excellent picture quality and directly access via the remote control. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the † or … button to select Setup. Result: The options available in the Setup group are displayed. 3 Press the ENTER ( ) button. 4 Press the † or … button to select TeleWeb. Press the ENTER ( ) button. Result: The TeleWeb menu is displayed. 5 To activate the TeleWeb feature, set the TeleWeb to On by pressing the œ or √button. ◆ If you set to On, 400 teletext pages can be stored. ◆ If you set to Off, 2100 teletext pages can be stored. 6 Press the † or … button to select Provider Search. Start the provider search by pressing the œ or √button. Result: It will be search only the channels stored. If it find a provider, the Added is displayed and continue the search. ➢ To stop the search before it has finished, press the EXIT/TV ( ) button. 7 When the search has been finished, press the † or … button to select Provider Select. Find the required provider by pressing the œ or √button. ➢ Select a provider and then the TeleWeb downloading will start. 8 Press the TeleWeb button to enter the TeleWeb mode. 9 If you want to download the TeleWeb information before switch the television off, select the Download by pressing the † or … button. Press the œ or √button to set to On. Result: Even though you turn off the TV on the channel no provider is selected, the channel will be automatically switched to the selected channel and TeleWeb downloading will start. During downloading, the picture will not be shown and only status bar will be displayed on the screen. (It takes 30 minutes to one hour depending on the program.) ➣ ◆When pressing the “ I / ” button (On/Off) on the panel of the television, the existing downloaded information will disappear. ◆If you enter the TeleWeb mode on the channel where no provider is selected, you can view only the information downloaded up to now. TeleWeb Feature (Option) TeleWeb TeleWeb : On Provider Search Provider Select Download : Off TeleWeb TeleWeb : On √ Provider Search √ Provider Select √ Download : Off √ Provider Search Stop Provider store in progress C11 P 9 Time √ Language : English √ AV Setup √ Digital NR : On √ Miscellaneous √ PC Setup √ TeleWeb √ Setup Move Enter Return TV Move Enter Return Move Enter Return TeleWeb TeleWeb : On √ Provider Search √ Provider Select √ Download : Off √ Move Enter Return TeleWeb TeleWeb : On Provider Search Provider Select Download : Off Move Enter Return Off On Off On Enter Return BN68-00597A-01 4/2/04 6:39 PM Page 52

TeleWeb Bookmark List √ Add Bookmark Home Page Move Add Exit Current programme. Selected provider. Service is loading. TeleWeb Bookmark List √ Add Bookmark Home Page Move Enter Exit Current programme. - - - - Selected provider. - - - - Service is loading. Bookmark List SAMSUNG ELECTRONICS TARA SYSTEMS KIA MOTORS MICRONAS OLYMPIC NEWS ECONOMICS Move Delete Exit TeleWeb Bookmark List √ Add Bookmark Home Page Move Enter Exit Current programme. - - - - Selected provider. - - - - Service is loading. Bookmarking the current page. 1 On the page you wish to add to the bookmark list press the MENU button. Result: The TeleWeb menu is displayed. 2 Press the † or … button to select Add Bookmark. Press the ENTER ( ) button. Result: The current page is added to the bookmark list. ➢ You can register up to six pages. If you add another URL when six bookmarks have been listed, the first URL will be deleted and the new URL will be listed as the sixth. Entering the bookmarked URL. 1 Press the MENU button. Result: The TeleWeb menu is displayed with the Bookmark List is selected. 2 Press the ENTER ( ) button. Result: The stored URLs are listed. 3 To erase a URL, select a required URL and press the TeleWeb (red) button. Result: The selected URL is erased and the listed URLs moves up one by one. 4 Select the URL you wish to enter by pressing the † or … button and press the ENTER ( ) button. Result: The current page moves to the selected URL and the menu is disappeared. Opening the Home Page 1 Press the MENU button. Result: The TeleWeb menu is displayed. 2 Press the † or … button to select Home Page. Press the ENTER ( ) button. Result: It moves to a home page. BN68-00597A-01 4/2/04 6:39 PM Page 53

Display the forward page of the TeleWeb Display the backward page of the TeleWeb Select a option. Confirm your choice. Easy Accessing the TeleWeb Service via the Remote Control BN68-00597A-01 4/2/04 6:39 PM Page 54

“MONITOR OUT” are used for the equipment with an RGB output, such as video game devices or video disc players. Rear of the TV (Input/Output) ①This end can be fitted with: ◆ A SCART connector ◆ Three RCA connectors (VIDEO + AUDIO-L/R) ②If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “AV 1” and the target VCR to “AV 2” so that you can redirect the signal from “AV 1” to “AV 2”. ③When you wish to record a programme, connect the receiver to “AV 1” and the VCR to “AV 2 or AV 3” so that you can redirect the signal from “AV 1” to “AV 2 or AV 3”. or ① VCR Decoder / Video game device Video disc player Satellite receiver DVD ② ③ Rear of the TV (Input/Output) Camcorder Video disc player Video game device Input/Output Specification Connector Input Output Video Audio (L/R) S-Video RGB Video + Audio (L/R) Ext.1 ✔ ✔ ✔ ✔ Only TV output is available. Ext.2 ✔ ✔ ✔ Output you can choose. Ext.3 ✔ ✔ ✔ Output you can choose. BN68-00597A-01 4/2/04 6:39 PM Page 55

The S-VIDEO1 and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output, such as a camcorder or VCR. Rear of the TV Camcorder VCR ①To play picture and sound, both the S-VIDEO and RCA connectors must be used. and ① and ① Side of the TV ☛ Whenever you connect an audio or video system to your television, ensure that all elements are switched off. Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions. BN68-00597A-01 4/2/04 6:39 PM Page 56

Connecting to the PC Input The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC. Personal Computer and Rear of the TV The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output. Personal Computer Rear of the TV and BN68-00597A-01 4/2/04 6:39 PM Page 57

①The “COMPONENT 1” connectors are used for equipment with a DVD output. (480i/480p/576i/576p/720p/1080i) ②The “COMPONENT 2” connectors are used for DTV receiver. (480i/480p/576i/576p/720p/1080i) DVD Rear of the TV DTV receiver ① ② Connecting Additional Speakers To take advantage of the surround sound system, connect additional speakers. The speaker terminals are located on the rear of the television: ◆ Two for the left-hand surround speaker (marked L) ◆ Two for the right-hand surround speaker (marked R) ➢ To improve the quality of the sound, connect the: ◆ Red wire to the red terminal ◆ Black wire to the black terminal Rear of the TV BN68-00597A-01 4/2/04 6:39 PM Page 58

Connecting the Home Theater System ①Connect the monitoring audio out L, and R jacks of the MONITOR OUT on the rear-side connection panel of the PDP TV to the AUDIO IN jacks of the DVD Home Theater System (or AV Receiver) using the audio cable. ②Press the SOURCE button to select the desired external device connected to the PDP TV. ③If you want to hear the sound through separate speakers, cancel the internal amplifier. To Display the DVD Home Theater ! Turn the PDP on and press the SOURCE button to select the Ext.1 (or Ext.2, Ext.3). @ Be sure to connect the video cable properly if desired external input (Ext.1, Ext.2, or Ext.3) cannot be selected. # Play the DVD after activating the DVD Home Theater System. $ Use the volume control of the Home Theater System while watching the PDP using the DVD Home Theater, where the PDP TV does not produce the audio. DVD Home Theater Rear of the TV AV Receiver Amplifier ① ② Use the Monitor Out ports of the PDP for Home Theater System Connections. ☛ ◆Refer to corresponding user’s manual from the manufacturer for wiring the speakers to the DVD Home Theater System (or AV Receiver). ◆Disable the PDP TV internal speaker to enjoy the rich sound through the speakers of your Home Theater System. ◆In this case, enjoy the sound from the Home Theater System while the PDP TV does not produce the audio. BN68-00597A-01 4/2/04 6:39 PM Page 59

ENG Parts The actual product may differ slightly from the illustration. Speakers 2 EA How to Assemble the Speakers (Standing) ① Remove the screws indicated on the rear of the PDP (6 screws on the left and right sides). ③ Secure the Speaker Dust Cover by setting it into the grooves located on the front side of the speakers. ④ Connect the speakers to the PDP using the speaker cable. The connection terminals are on the rear side of both the PDP and the speakers. (Match the color coded terminals and cables.) ② Attach the Bracket Pads to the Speaker’s Guide Bracket. Set the Speaker Guide Bracket into the square grooves located on either side of the PDP’s bottom rear and secure it with the provided screws ①, ➁. (Always use the proper screws, as indicated.) Middle Cabinet (Wall Mount Only) 1 EA Speaker Dust Cover 1 EA Speaker Cable Screws Screw① : 6EA Screw➁ : 4EA 3 EA Bracket Pads ➢ This speaker installation guide is for the 4240 Model. BLACK BLACK RED RED WARNING 1. When moving the PDP with the speakers attached, be sure to hold on to the PDP to prevent damage. (Damage may occur to the speaker connecting brackets or the speakers.) 2. Speakers of 8ΩImpedance, 15W Nom. Power, 30W Max. Power is recommended. Bracket Pads Screw① Screw② BN68-00597A-01 4/2/04 6:39 PM Page 60

ENG Parts The actual product may differ slightly from the illustration. Speakers 2 EA How to Assemble the Speakers (Wall Mount) ① Remove the screws indicated on the rear of the PDP (6 screws on the left and right sides, 2 screws on the center). ③ Secure the Speaker Dust Cover by setting it into the grooves located on the front side of the speakers. ④ Connect the speakers to the PDP using the speaker cable. The connection terminals are on the rear side of both the PDP and the speakers. (Match the color coded terminals and cables.) Bracket Pads ② Attach the Bracket Pads to the Speaker’s Guide Bracket. Set the Speaker Guide Bracket into the square grooves located on either side of the PDP’s bottom rear and secure it with the provided screws ①, ➁. Secure the Middle Cabinet to the center of the PDP with a screw ①. (Always use the proper screws, as indicated.) Middle Cabinet (Wall Mount Only) 1 EA Speaker Dust Cover 1 EA Speaker Cable Screws Screw① : 6EA Screw➁ : 4EA 3 EA Bracket Pads BLACK BLACK RED RED WARNING 1. When moving the PDP with the speakers attached, be sure to hold on to the PDP to prevent damage. (Damage may occur to the speaker connecting brackets or the speakers.) 2. Speakers of 8ΩImpedance, 15W Nom. Power, 30W Max. Power is recommended. Screw① Screw② BN68-00597A-01 4/2/04 6:40 PM Page 61

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.) On the windows screen, select in the following sequence: Start ➞ Settings ➞ Control Panel. When the control panel screen appears, click on Display and a display dialog-box will appear. Select the Settings tab in the display dialog-box. The two key variables that apply the television-PC interface are “Resolution” and “Colours”. The correct settings for these two variables are: ◆Size (sometimes called “Resolution”) - 1024 x 768 pixels ◆Colour 32-bit colour Shown at left is a typical screen for “Display” dialog box. If a vertical-frequency option exists on your display settings dialog box, the correct value is 60 Hz. Otherwise, just click OK and exit the dialog box. BN68-00597A-01 4/2/04 6:40 PM Page 62

Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: (N: Negative / P: Positive) ◆The interlace mode is not supported. ◆The television might operate abnormally if a non-standard video format is selected. Notes ◆The PC text quality for PS42P4A is optimum in XGA mode (1024 x 768). ◆When this television is used as a PC display, 32-bit colour is supported. ◆Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows). Check your PC instruction book for information about connecting your PC to a television. ◆If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.3kHz (horizontal). In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the SOURCE button to enter the Video mode. Also, make sure that the PC is connected. ◆When connecting a notebook PC to the television, make sure that the PC screen is displayed through only the television (Otherwise, random signals might appear). ◆When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable connections. ◆The Display Settings Table above complies to the IBM/VESA standards, and based on the analog input. ◆The DVI support mode is regarded as same to the PC support mode. ◆The best timing for the vertical frequency to each mode is 60Hz. IBM PC / AT Compatible Video Signal Vertical frequency (Hz) 70.086 85.080 85.080 70.087 85.039 59.940 72.809 75.000 85.008 56.250 60.317 72.188 75.000 85.061 60.000 72.000 75.000 60.004 70.069 75.029 84.997 Horizontal frequency (kHz) 31.469 37.861 37.861 31.469 37.927 31.469 37.861 37.500 43.269 35.156 37.879 48.077 46.875 53.674 29.838 36.072 37.650 48.363 56.476 60.023 68.677 Vertical polarity N N P P P N N N N N/P P P P P N N P P Horizontal polarity P P N N N N N N N N/P P P P P N N P P Dot x Line 640 x 350 640 x 400 720 x 400 640 x 480 800 x 600 848 x 480 1024 x 768 nVidia chipset BN68-00597A-01 4/2/04 6:40 PM Page 63

only wired on the AV1 or AV2 or AV3 connector. Pin Signal 1 Audio output R 2 Audio input R 3 Audio output L 4 Audio chassis return 5 Video chassis return (RGB blue) 6 Audio input L 7 RGB blue input 8 Switching voltage 9 Video chassis return (RGB green) 10 AV-Link (Ext 1) 11 RGB green input Pin Signal 12 - 13 Video chassis return (RGB red) 14 - 15 RGB red input 16 Blanking signal (RGB switching) 17 Video chassis return 18 Blanking signal ground 19 Video output 20 Video input 21 Screening/chassis return SCART Connector (AV1/AV2/AV3) Pin PC IN 1 Red (R) 2 Green (G) 3 Blue (B) 4 Grounding 5 Grounding (DDC) 6 Red (R) Grounding 7 Green (G) Grounding 8 Blue (B) Grounding 9 Reserved 10 Sync Grounding 11 Grounding 12 Data (DDC) 13 Horizontal sync. 14 Vertical sync. 15 Clock (DDC) PC Input Connector (15Pin) Pin Signal 1 T.M.D.S. Data2- 2 T.M.D.S. Data2+ 3 T.M.D.S. Data2/4 Shield 4 T.M.D.S. Data4- 5 T.M.D.S. Data4+ 6 Clock (DDC) 7 Data (DDC) 8 Not Connected 9 T.M.D.S. Data1- 10 T.M.D.S. Data1+ 11 T.M.D.S. Data1/3 Shield 12 T.M.D.S. Data3- 13 T.M.D.S. Data3+ 14 +5V Power 15 5V Grounding 16 Hot Plug Detect 17 T.M.D.S. Data0- 18 T.M.D.S. Data0+ 19 T.M.D.S. Data0/5 Shield 20 T.M.D.S. Data5- 21 T.M.D.S. Data5+ 22 T.M.D.S. Clock Shield 23 T.M.D.S. Clock+ 24 T.M.D.S. Clock- DVI Input Connector (24Pin) BN68-00597A-01 4/2/04 6:40 PM Page 64

No sound or picture Normal picture but no sound No picture or black and white picture Sound and picture interference Blurred or snowy picture, distorted sound Remote control malfunctions ◆ Check that the mains lead has been connected to a wall socket. ◆ Check that you have pressed the “ I ” button (On/Off) and the POWER ( ) button. ◆ Check the picture contrast and brightness settings. ◆ Check the volume. ◆ Check the volume. ◆ Check whether the volume MUTE ( ) button on the remote control has been pressed. ◆ Adjust the colour settings. ◆ Check that the broadcast system selected is correct. ◆ Try to identify the electrical appliance that is affecting the television, then move it further away. ◆ Plug your television into a different mains socket. ◆ Check the direction, location and connections of your aerial. This interference often occurs due to the use of an indoor aerial. ◆ Replace the remote control batteries. ◆ Clean the upper edge of the remote control (transmission window). ◆ Check the battery terminals. Before contacting Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer. BN68-00597A-01 4/2/04 6:40 PM Page 65

CABLE CODE LIST Anvision 017, 018 GI 041 Hamlin 003, 024, 031 Hitachi 025, 030 Jerrold 038, 039 Macom 025, 030 Magnavox 019, 023, 028 Oak 026 Panasonic 003, 022, 027, 037, 044 Philips 019, 021, 023, 028 Pioneer 018, 020, 004, 044 RCA 014, 022, 040 Regal 003 Regency 015, 023 SA 042, 043 Samsung 000, 001, 002, 003, 004, 005, 006, 007 Scientific Atlanta 042, 043 Sprucer 022 Stargate 2000 036 Sylvania 016 Texscan 016 Tocom 032 Universal 033, 034 Viewstar 019, 021,023, 028 Wamer amex 046 Zenith 017, 029, 035, 037, 045 DVD CODE LIST 000 001 002 003 005 006 007 008 009 Samsung Samsung JVC PROSCAN, RCA Panasonic LG(Goldstar) Sony Denon Curtis Mathes BN68-00597A-01 4/2/04 6:40 PM Page 66

VCR CODE LIST Admiral 020 Aiwa 025 Akai 027, 004, 032 Audio Dynamics 007, 026 Bell&Howell 018 Broksonic 022 Candle 002, 006, 003, 015, 008, 055 Canon 021, 056 Citizen 002, 006, 003, 015, 008, 055 Colortyme 007 Craig 002, 024 Curtis Mathes 002, 017, 007, 008, 021, 025, 056, 064, 066 Daewoo 003, 015, 010, 011, 012, 013, 014, 016 DBX 007, 026 Dimensia 017 Dynatech 034 Emerson 001, 003, 006, 021, 022, 025, 030, 032, 034, 040, 047, 050, 052, 060, 063, 065, 066, 067, 069 Fisher 018, 024, 028, 029, 048, 051, 061 Funai 025 General Electric 017, 002, 021, 005, 056 Go Video 002 LG(Goldstar) 006, 007, 008, 009, 010 Harman Kardon 007 Hitachi 019, 025, 041, 042 Instant Replay 021 JC Penny 002, 007, 018, 019, 021, 026, 037, 041, 054, 056 JVC 007, 008, 018, 021, 026, 037 Kenwood 007, 008, 018, 026, 037 KLH 070 Lioyd 025 Logik 038 LXI 025 Magnavox 021, 036, 056, 059 Marantz 018, 021, 007, 026, 037, 008, 062, 036 Marta 006 MEI 021 Memorex 006, 021, 024, 025 MGA 034 Midland 005 Minolta 019, 041 Mitsubishi 019, 034, 041, 046 Montgomery Ward 020 MTC 002, 025 Multitech 002, 025, 038, 005 NEC 018, 007, 026, 037, 008, 062, 064 Optimus 020 Panasonic 021, 056, 071, 072 Pentax 019, 041 Pentex Research 008 Philco 021, 036, 056, 059 Philips 021, 036 Pioneer 019, 026, 039, 053 Portland 015, 049, 055 PROSCAN 017 Quartz 018 Quasar 021, 056 Radio Shack/Realistic 006, 018, 020, 021, 024, 025, 029, 034, 048, 056 RCA 017, 019, 002, 021, 035, 041, 043, 057, 068 Samsung 000, 001, 002, 003, 004, 005 Sansui 026 Sanyo 018, 024 Scott 003, 047, 052, 067 Sears 018, 019, 006, 024, 028, 029, 041, 048, 051 Sharp 020, 034, 045, 015 Shimom 027, 033, 038, 058 Signature 025 Sony 027, 033, 044 Sylvania 021, 025, 036, 056, 059 Symphonic 025 Tandy 018, 025 Tashika 006 Tatung 037 Teac 025, 037, 068 Technics 021 Teknika 021, 006, 025, 031 TMK 066 Toshiba 003, 019, 029, 051, 052 Totevision 002, 006 Unitech 002 Vector Research 007, 026 Victor 026 Video Concepts 007, 026 Videosonic 002 Wards 002, 003, 006, 019, 020, 021, 024, 025, 034, 038, 041 Yamaha 007, 008, 018, 026, 037 Zenith 023, 027, 033, 073 BN68-00597A-01 4/2/04 6:40 PM Page 67

- Do not hesitate to contact your retailer or service agent if a change in the performance of your product indicates that a faulty condition may be present. BN68-00597A-01 BN68-00597A-01 4/2/04 6:40 PM Page 68