Exmark LAZER Z series Operator's Manual

PART NO. 1-633706 LOCATION: LH Side of Cutting Height Adjustment Plate PART NO. 1-633462 LOCATION: Rubber Heat Shield Flap behind Seat PART NO. 1-303508 LOCATION: RH Side on Top Rear of Mower Deck PART NO. 1-643339 LOCATION: Top of Right Engine Baffle PART NO. 1-323540 LOCATION: Left Rear Corner Top of Mower Deck For Units with S/N 464,999 and Lower PART NO. 1-633702 LOCATION: Bottom Side of Floor Pan PART NO. 1-633922 LOCATION: Front Center on Top of Mower Deck PART NO. 1-523552 LOCATION: Top of Hydraulic ...

c) Lubricate front caster pivots once a year. Remove hex plug and cap. Thread grease zerk in hole and pump with grease until it oozes out around top bearing. Remove grease zerk and thread plug back in. Place cap back on. 5.1.18 Lubricate caster wheel hubs: Service Interval: Once Yearly a) Stop engine, wait for all moving parts to stop, and remove key. b) Remove caster wheel from caster forks. c) Remove seal guards from the wheel hub. d) Remove one of the spacer nuts from the axle assembly in the caster wheel. Note that thread locking adhesive has been applied to lock the spacer nut ...

By moving both levers an equal amount forward or back from the neutral position the machine can be caused to move forward or backward in a straight line. Movement of the left lever forward will cause the left drive wheel to rotate in a forward direction. Movement of the right lever forward will cause the right drive wheel to rotate in a forward direction. To stop forward travel, pull the levers back to the neutral position. To turn left while moving forward, move the left lever back toward neutral to slow the left drive wheel. To turn right while moving forward, move the right lever b ...

e) Make sure the parking brake is set and motion control levers are moved out (neutral lock position). f) Check that the PTO is disengaged. g) Check that the spark plug wires are properly connected. h) Check for loose or faulty wiring connections. i) Check for corrosion at all wiring connections. Even minor corrosion may cause a faulty connection. Clean connector terminals thoroughly with electrical contact cleaner, apply dielectric grease and reconnect. NOTE: When disconnecting electrical connectors DO NOT pull on the wires to separate the connectors. NOTE: After carefully checking ...

FIGURE 16 THROTTLE TENSION 5.2.11 Electric Clutch Adjustment: No adjustment necessary. 5.2.12 Reverse Indicator Adjustment: a) Stop engine, wait for all moving parts to stop, and remove key. b) Unhook seat latch and tilt seat forward. c) Begin with either the left or right motion control lever. Move lever to the neutral position and pull lever back until the clevis pin (on arm below pivot shaft) contacts the end of the slot (just beginning to put pressure on spring), See Figure 17. d) Check where lever is relative to notch in console (should be centered allowing lever to pivot ou ...

CAUTION POTENTIAL HAZARD ♦ Engine coolant is toxic. WHAT CAN HAPPEN ♦ Swallowing coolant can cause poisoning. HOW TO AVOID THE HAZARD ♦ Do not swallow ♦ Keep out of reach of children and pets. With machine on level surface and with cool engine, remove radiator cap (under hood) and add a 50/50 mix of water and engine coolant until liquid level is as high as possible without overflowing. Reinstall radiator cap, making sure that the cap is completely seated by pressing down firmly while turning until the cap stops. Add 50/50 coolant mix to overflow bottle on the left side of the ...

LINE OF PRODUCTS FOR TURF CARE LAZER Z® LAZER Z® HP LAZER Z® XP LAZER Z® CT TURF RANGER® VIKING HYDRO TURF TRACER® TURF TRACER® HP METRO® METRO® HP ULTRA VAC™ ULTRA VAC™ QDS SELF STEERING SULKY GRASS CATCHER MICRO-MULCH ™ ACCESSORY WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. ® MFG. CO. INC. ©1997-2003 PART NO. 103-5505 Rev. A EXMARK MFG. CO. INC. (402) 223-6300 INDUSTRIAL PARK BOX 808 FAX (402) 223-5489 BEATRICE, NE 68310 ALL RIGHTS RE ...

EFFECTIVE DATE: September 1, 1995 Program If your Exmark dealer does not have the Exmark part in stock, Exmark will get the parts to the dealer the next business day or the part will be FREE* Guaranteed!! How the Program Works 1. If dealer does not have part in stock for a "down" unit at the time of request by customer, the dealer contacts his distributor by 1:00 p.m., local time, and requests Exmark Parts Plus shipment of six (6) line items or less. 2. Distributor ships part(s) to dealer or customer, as requested by dealer, same day, overnight UPS Distribut ...