Samsung MM-T5 Instruction Manual

This Compact Disc player is classified as a CLASS 1 LASER product. Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION-INVISIBLE LASER RADIATION WHEN OPEN AND INTER LOCKS DEFEATED, AVOID EXPOSURE TO BEAM. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS- TURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LASER CLASE 1 This symbol indicates that dangerous voltage which can cause electric shock is present inside this unit. This symbol alerts you to important operating and maintenance instructions accompanying the unit. Wiring the Mains Power Supply Plug(UK Only) IMPORTANT NOTICE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover omitted. If the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord. IMPORTANT The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:– The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.

INSTALLING YOUR MICRO-COMPONENT SYSTEM Front Panel View ........................................................................................................................................................................................4 Remote Control ..........................................................................................................................................................................................5 Rear Panel View ........................................................................................................................................................................................6 Where to Install your Micro-Component System........................................................................................................................................7 Connecting your System to the Power Supply ..........................................................................................................................................7 Inserting Remote Control Batteries ............................................................................................................................................................7 Connecting to an External Source ............................................................................................................................................................8 Speaker Connection ..................................................................................................................................................................................8 Connecting the AM (MW)/LW Aerial ..........................................................................................................................................................9 Connecting the FM Aerial ..........................................................................................................................................................................9 Setting the Clock ......................................................................................................................................................................................10 CD-PLAYER To replay the CD/MP3-CD........................................................................................................................................................................10 Regarding the playback of CD-R/RW ......................................................................................................................................................11 Selecting a Track......................................................................................................................................................................................11 Selecting the MP3-CD album and track ..................................................................................................................................................11 Searching for a Specific Music Passage on a CD ..................................................................................................................................12 Function to skip through 10 tracks at a time ..........................................................................................................................................12 Last Memory Function ............................................................................................................................................................................12 Repeating One or All Tracks on the Compact Discs................................................................................................................................13 Repeat A B Function ....................................................................................................................................................................13 Programming the Order of Playback ................................................................................................................................................13 Checking or Changing Programmed Tracks ..........................................................................................................................................14 TUNER Searching for and Storing the Radio Stations..........................................................................................................................................14 Selecting a Stored Station........................................................................................................................................................................15 Improving Radio Reception......................................................................................................................................................................15 About RDS broadcasting ..........................................................................................................................................................................16 About RDS DISPLAY Function ................................................................................................................................................................16 PTY(Program Type) indication and PTY-SEARCH function......................................................................................................................17 TAPE DECK Listening to a Cassette ............................................................................................................................................................................18 Recording a Compact Disc ......................................................................................................................................................................18 Recording a Radio Program ....................................................................................................................................................................18 OTHER FUNCTIONS Timer Function ........................................................................................................................................................................................19 Cancelling the Timer ................................................................................................................................................................................19 Power Sound Function ........................................................................................................................................................................20 EQ/S.BASS (Super Bass) Function ..........................................................................................................................................................20 Sleep Timer............................................................................................................................................................................................20 MUTE Function......................................................................................................................................................................................20 Connecting Headphones ...................................................................................................................................................20 RECOMMENDATIONS FOR USE Safety Precautions................................................................................................................................................................................. 21 Cleaning your Micro-Component System............................................................................................................................................... 21 Precautions When Using Compact Discs ................................................................................................................................................22 Precautions When Using Audio Cassettes ..............................................................................................................................................22 Before Contacting the After-Sales Service ..............................................................................................................................................22 Technical Specifications ..........................................................................................................................................................................23 Thank you for buying this SAMSUNG micro-component system. Please take time to read these instructions. They will allow you to operate your system with ease and take full advantage of its features.

1. TAPE PLAY 2. STANDBY/ON 3. MP3-CD/CD PLAY/PAUSE 4. RECORD/PAUSE 5. TUNER / BAND 6. AUX 7. SKIP OR SEARCH REWIND 8. HEADPHONE JACK 9. STOP/TUNING MODE 10. SKIP OR SEARCH FORWARD 11. PUSH OPEN (CD DOOR OPEN /CLOSE) 12. TAPE SPEED 13. CD OR TAPE REPEAT A B 14. POWER SOUND 15. VOLUME CONTROL 16. EQ / SUPER BASS 17. PUSH EJECT (CASSETTE DOOR OPEN/CLOSE) 1 2 3 4 5 14 13 12 11 6 7 8 9 10 15 16 17

2. STANDBY/ON 3. TUNER/BAND 4. AUX 5. SLEEP 6. POWER SOUND 7. CD SKIP OR SEARCH 8. CD STOP 9. CD REPEAT 10. VOLUME CONTROL 11. TAPE REWIND 12. TAPE STOP 13. TAPE PLAY 14. TAPE FAST-FORWARD 15. TUNING UP OR DOWN SEARCH/ MP3-CD ALBUM SELECT 16. TUNING MODE / CD+10 17. CD PLAY/PAUSE 18. DISPLAY (RDS) 19. PTY(RDS) 20. TAPE SPEED 21. REPEAT A-B /FM MONO/STEREO 22. TIMER ON/OFF 23. MUTE 24. EQ/SUPER BASS 25. TIMER/CLOCK CD/MP3-CD TAPE TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED REPEAT TUNING MODE VOLUME TUNING / ALBUM MUTE / +10 POWER SOUND DISPLAY PTY RDS 1 2 3 4 5 6 7 8 9 10 11 12 25 24 23 22 21 20 19 18 17 16 15 14 13

1. FM Aerial Connector Terminal 2. AM Aerial Connector Terminals 3. AUX-Input 4. Loudspeakers Connector Terminals 6 1 2 3 4 GB

Before plugging your system into a main socket, you must check the voltage. Plug the main lead into an appropriate socket. Press the Standby/On button to switch your micro-component system on. To take full advantage of your new micro-component system, fol- low these installation instructions before connecting the unit. Install the system on a flat, stable surface. Never place this unit on carpeting. Never place this unit in an outdoor area. Maintain an open space of approximately 6 inches (15 cm) on the sides and rear of the system, for ventilation purposes. Make sure that you have enough room to open the compact disc compartment easily. Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound. Direct the loudspeakers towards the listening area. For optimum performance, make sure that both speakers are placed at an equal distance above the floor. Where to Install Your Micro-Component System Connecting your System to the Power Supply Insert or replace remote control batteries when you: Purchase the micro-component system Find that the remote control is no longer operating correctly When replacing the batteries, use a new set of batteries and never mix alkaline and manganese batteries. Place your thumb on the position marked on the battery compartment cover (rear of the remote control) and push the cover in the direction of the arrow. Insert two AAA, LR03 or equivalent batteries, taking care to respect the polarities: + on the battery against + in the battery compartment – on the battery against – in the battery compartment Replace the cover by sliding it back until it clicks into position. If you will not be using the remote control for a long time, remove the batteries to prevent corrosion. 1 2 3 2 1 6 Inserting Remote Control Batteries

sound quality of your micro-component system when listening to other sources. Examples: A television A video disc player A Hi-Fi stereo video cassette recorder To connect to the external source, the source must have an audio output. In addition, you need an RCA connection cable. Set the system to standby mode and disconnect it and the external source from the main socket. Connect the audio cable to the rear of the micro-component system. Connect the... To the connector marked... Red jack............................................... R (right) White jack............................................. L (left) For optimum sound quality, do not invert the right and left channels. Plug the system back into the main socket and press Standby/On ( ) to switch it on. Select the AUX source by pressing AUX. Result: AUX is displayed. Switch the external source on. Adjust the volume and balance as required: Volume Equaliser Example: You can watch a film and take advantage of stereo sound provided that the original sound track is in stereo (as if you were in a cinema). Connecting to an External Source 1 2 3 4 5 6 Speaker Connection Directions in Installing Speaker Installation in a place near heating apparatus, under direct lay of light or with high humidity may cause performance degradation of the speaker. Do not install on the wall or on a high place of pole or other unsta- ble place to prevent any safety accident caused by falling of the speaker. Do not take the speaker apart from TV or computer monitor. The speaker near the TV or computer monitor may influence the quality of the screen display. (Right Speaker) (Left Speaker) 6 The loudspeaker connector terminals are located on the rear of the system (red and black tabs). There are four terminals on the system: Two for the left speaker (marked L) Two for the right speaker (marked R) To achieve the correct sound quality, connect the: Red wire to the + terminals Black wire to the - terminals 4 4 3

Placed on a stable surface Fixed to the wall (you must first remove the base) The AM aerial connector terminals are located on the rear of the system and are marked AM . To avoid noise interference, check that the loudspeaker wires do not run close to the aerial wires. Always keep them at least 2 inches (5 cm) away. Connecting the AM (MW)/LW Aerial How to connect a COAXIAL TYPE aerial. Connect a 75Ωantenna to the FM antenna terminal. Plug the connector on the FM aerial supplied into the coaxial socket (75Ω) marked FM on the rear of the system. Follow the instructions given on Page 14 to tune into a radio station, and determine the best position for the aerial. If reception is poor, you may need to install an outdoor aerial. To do so, connect an outdoor FM aerial to the FM socket on the rear of the system using a 75Ωcoaxial cable (not supplied). Connecting the FM Aerial 6 6

your system on and off automatically. You should set the clock: When you first purchase the micro-component system After a power failure After unplugging the unit For each step, you have a few seconds to set the required options. If you exceed this time, you must start again. Switch the system on by pressing Standby/On ( ) Press TIMER /CLOCK twice. Result: CLOCK is displayed. Press PROGRAM /SET. Result: The hour flashes. To... Press... Decrease the hours .............................................. Increase the hours .............................................. When the correct hour is displayed, press PROGRAM /SET. Result: The minutes flash. To... Press... Decrease the minutes .................................... Increase the minutes .......................................... When the correct time is displayed, press PROGRAM /SET. Result: The clock starts and is displayed, even when the system is in standby mode. You can display the time, even when you are using another function, by pressing TIMER /CLOCK once. 10 Setting the Clock 1 2 3 4 5 6 7 CD/MP3-CD TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED TUNING/ MUTE POWER SOUND DISPLAY PTY RDS CD/MP3-CD TAPE SLEEP EQ/S.BASS TAPE SPEED TUNING MODE REPEAT VOLUME TUNING/ ALBUM +10 POWER SOUND DISPLAY PTY RDS 4,6 This unit has been designed to playback the MP3-MP3-CDs: Audio CD, CD Text, CD-R, CD-RW and MP3-CD. Continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage the unit. Select the CD function by pressing MP3-CD( ) button. Press the PUSH OPEN ( ) button. Result: The compartment opens. Place your disc in the compartment, with the label on the disc facing upwards. Close the compartment by pressing the PUSH OPEN ( ) button again until it clicks into place. Press the MP3-CD( ) button. Your CD Player will take a few moments to scan through all the tracks recorded on a particular MP3-CD The English name of the song may be indicated on the display only if directly downloaded from the PC or if the purchased MP3-CD is sorted according to titles(directory). (Other languages besides English may not be indicated.) The English name of the track may not be indicated depend- ing on the characteristics of the MP3-CD. To stop playback temporarily, press the MP3-CD ( ) button. Press MP3-CD ( ) again to continue playing the disc. Press the STOP ( ) button when you have finished. 1 2 3 4 5 7 6 To replay the CD/MP3-CD 2 1 3,5,7 4,6 2,4 7 1, 5, 6

selected on stopping or during playbacks. You can select the album by pressing TUNING/ALBUM button on the remote control. Result: ALBUM is displayed. To move the album, press the or button. To move the track , press the , button . Result: TRACK is displayed and the track number is moved. GB 11 Regarding the playback of CD-R/RW In the case of an original CD-R(Recordable) recorded in audio CD format, CD-RW(Rewitable) and editing by the user, playback is processed on the respective completed status. (The player may not be played back according to the characteristics of the CD or recorded status.) The CD-RW is comparably less reflexive than CD which causes more time delay to read. You can select the track you wish to listen to, either when the compact disc player is stopped or when a disc is playing. To start playback at the beginning of the... Press... Next track once Current track once Previous track twice Track of your choice or the appropriate number of times. Selecting a Track CD/MP3-CD MO/ST AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED TUNING MODE REPEAT VOLUME TUNING/ ALBUM +10 POWER SOUND DISPLAY PTY RDS Selecting the MP3-CD album and track 1 2 3 CD/MP3-CD TAPE TUNING MODE REPEAT VOLUME TUNING/ ALBUM +10 POWER SOUND 3 3 1,2 1,2 Album Movement Track Movement

tracks at a time Press the +10 button briefly while playing back a CD. The track 10 tracks after the current one will then be played back. Example: If you want to select track 43 during playback of track 15, press the +10 button three times, and then press the button three times. 15 ➝20 ➝30 ➝40 ➝41 ➝42 ➝43 CD/MP3-CD TAPE SLEEP EQ/S.BASS TAPE SPEED TUNING MODE REPEAT VOLUME TUNING/ ALBUM +10 POWER SOUND DISPLAY PTY RDS When listening to a compact disc, you can quickly search for a specific music passage on a track. To search through the tracks... Press and hold down... Forwards for at least one second Backwards for at least one second It is recommended that you turn the volume down before using this function. Searching for a Specific Music Passage on a CD What is MP3? Playback sequence of albums and tracks In case of Window Explorer display. The arrows indicates playback sequence of albums and tracks. Tracks with jpg, wav or doc only are not audio files and therefore will be skipped. MP3 means MPEG1 Layer 3, the global standard for audio signal compression technology. It uses digital compression technology to compress original sound data by up to 12 times without sound quality degradation. File Compatibility The unit will playback files created in MP3 format (Mpeg1.Layer3) with *.mp3 as their extension. Files created in MP2 format (Mpeg1.Layer2) with *.mp2 as their extension can also be played back. How many MP3 files can a CD-R or CD-RW disc record? The maximum capacity of one CD-R or CD-RW disc is 680MB. Normally, one MP3 file has a capacity of 4MB, therefore approximately 170 files can be recorded on a single disc. Kevin01.mp3 Album 01 (E) CD-ROM drive Kevin02.mp3 Kevin03.mp3 Kevin04.mp3 Kevin.jpg Life.doc Skipped Album 02 Summer05.mp3 Summer06.mp3 Garden.mp3 Garden.mp3 Album 04 Album 03 Michael07.mp3 Michael08.mp3 Water.mp3 Water.mp3 Album 05 Skipped Kenny01.wav Kenny02.wav Butterfly.mp3 Album 06 Piano14.mp3 John15.mp3 Album 07 +10 CD/MP3-CD VOLUME TUNING/ ALBUM POWER SOUND DISPLAY PTY RDS +10 +10 +10 CD/MP3-CD TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED MUTE POWER SOUND DISPLAY PTY RDS When MP3-CD playback is selected again after your CD player has been stopped or turned off, this function allows playback from the start of the track that you last listened to. Press the PROGRAM/SET button while your MP3-CD is being played . The LAST ON and LAST OFF may be repeatedly selected. Last Memory Function (This function is only available during playback of MP3-CD.)

(This function is not available during playback of a MP3-CD.) When you select CD(TAPE) REPEAT A B playback, the music passages to which you were listening are repeated 3 times. Press MP3-CD( ) or TAPE button. Result:The CD(TAPE) player starts playing. Press REPEAT A B button. Result:The indications appear: START The flashes appear: A A Time is memorised. Press REPEAT A B button. Result:The indications appear: END B Time is memorised. Your selected passages are repeated 3 times. When you have finished the Repeat playback, Press REPEAT A B. Programming the Order of Playback (This function is only available during playback of a CD. You can decide for yourself: The order in which you listen to the tracks The tracks to which you do not wish to listen This feature can be combined with the CD Repeat function. If necessary, stop the player by pressing STOP ( ). Press PROGRAM / SET. Result: is displayed. Select the required track by pressing the SKIP buttons: to move forwards through the tracks to move backwards through the tracks Press PROGRAM / SET. Result: is displayed. To select other tracks, repeat Steps 3 and 4. You can programme up to 24 tracks. When you have finished selecting the tracks, press MP3-CD ( ) to start listening to the selection, in the order in which the tracks were programmed. Press STOP ( ) twice to cancel the selection when the disc is playing. CD/MP3-CD TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED TUNING MODE REPEAT VOLUME TUNING/ ALBUM MUTE +10 POWER SOUND DISPLAY PTY RDS 1 2 3 4 1 2 3 4 5 6 7 1,7 3 6 2,4 3 You can repeat indefinitely: A specific track on a compact disc. All tracks on the compact disc selected. To repeat... Press Repeat on the Front Panel one or more times until... The current track indefinitely REPEAT 1 is displayed All songs REPEAT ALL is displayed When you wish to stop the Repeat function, press STOP( ) button. Result:REPEAT is no longer displayed and the function is cancelled. Repeating One or All Tracks on the Compact Discs 1 2 CD/MP3-CD TUNING MODE REPEAT VOLUME TUNING/ ALBUM +10 2 1 2,3,4 1 1

You must have selected at least one track. Press STOP ( ) once if you have started listening to the selection. Press PROGRAM / SET. Each time you press Program/Set, the next selection is displayed. Press PROGRAM / SET one or more times until the track to be changed is displayed. Press or to select the new track. Press PROGRAM / SET. Press MP3-CD ( ) to start listening to the selection. Result: The first track selected is played. You can change one or more tracks in your initial selection You can store up to: 15 FM stations 8 MW station 7 LW station Switch the system on by pressing Standby/On ( ) Select the TUNER function by pressing TUNER/BAND on the front panel. Select the required frequency band by pressing TUNER/BAND again. Result:The appropriate indication is displayed: FM Frequency Modulation AM(MW) Medium Wave LW Long Wave To search for a station ... Press Tuning Mode ... Manually.......................................One or more times until MANUAL is displayed. Automatically................................One or more times until AUTO is displayed. Select the station to be stored by pressing , on the front panel to decrease or increase the frequency respectively. To scroll through the frequencies faster when searching manually, hold down the , on the front panel . The automatic search procedure may stop on a frequency that does not correspond to a radio station. If this happens, use the manual search mode. Adjust the volume by: Turning the VOL.+,- knob on the front panel or Pressing the VOLUME+, - button on the remote control. Select the FM stereo or mono mode by pressing MO/ST on the remote control. Checking and Changing Programmed Tracks Searching for and Storing the Radio Stations 1 2 3 4 5 6 1 2 3 4 5 CD/MP3-CD TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED VOLUME TUNING/ ALBUM MUTE POWER SOUND DISPLAY PTY RDS 6 7 TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED MO/ST 7 6 1 4 4 2,3,5 1 2,3 4 5 5 6

search for another station. Otherwise: a Press PROGRAM/SET Result: The program number is displayed for a few seconds. b Press TUNING and to assign a program number between 1 and 15. c Press PROGRAM/SET to store the radio station. Result: The program number is no longer displayed and the station is stored. To store any other radio frequencies required, repeat Steps 3 to 6. The PROGRAM function can be used to assign a new station to an existing program number. You can listen to a stored radio station as follows: Switch the system on by pressing Standby/On ( ). Select the TUNER function by pressing TUNER/BAND on the front panel. Select the required frequency band by pressing TUNER/BAND. Select the radio station as follows. To listen to ... Press ... A stored station........................... a Press the TUNING MODE button until “PRESET” is displayed. b TUNING and to select the required station. Press TUNING MODE again to exit the stored station selection function. You can improve the quality of radio reception by: Rotating the FM or AM(MW) aerial Testing the positions of the FM and AM(MW) aerials before fixing them permanently If reception from a specific FM radio station is poor, press MO/ST to switch from stereo mode to mono. The quality of the sound will be improved. GB Selecting a Stored Station Improving Radio Reception Searching for and Storing the Radio Stations(continued) 8 9 1 2 3 4 CD/MP3-CD TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED TUNING MODE REPEAT VOLUME TUNING/ ALBUM MUTE +10 POWER SOUND DISPLAY PTY RDS CD/MP3-CD TAPE TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED TUNING MODE REPEAT VOLUME TUNING/ ALBUM +10 POWER SOUND DISPLAY PTY RDS TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED MUTE 8 8 8 1 BAND 2,3 MO/ST 4 15 +10 4 4

Displays the name of broadcasting station. Press the RDS DISPLAY button to select the PS NAME. "PS NAME" appears on the display. If the PS information is being received, the PS name (BBC, AFO, NDR, etc.) is shown on the display. If the PS information isn't received, the original FM frequency is shown. Even though no RDS DISPLAY button is pressed, the reception of PS information ensues the PS name is displayed. About 'RT' MODE Displays the character transmitted from the broadcasting station. Press the RDS DISPLAY button to select the RT MODE. "RT" appears on the display. If the RT information is being received, the received information is shown on the display. If the RT information isn't received, the "NO RT" is shown on the display. About CT(Clock Time) Sets the time of RDS clock. To select the CT time, set the RDS DISPLAY button to CT MODE. The CT information will take up to 2 minutes to be decoded therefore the clock isn’t displayed immediately. If there is no received CT information, "NO CT" is displayed. This unit has the RDS (Radio Data System) function, which enables for the various information such as broadcasting station, radio text, time and 30 types of programs (News, Rock, Classic, etc.) to be received from the FM RDS station together with normal radio signal. Press the Standby/On ( ) button. Receive the FM radio. See the radio receiving method on the page 14~15. FM and frequency are shown on the display If the received station transfers the RDS information, 'RDS' appears automatically on the display. Press the RDS DISPLAY button to select the desired RDS mode. Whenever the button is pressed, RDS mode changes as follows. The RDS function is available only in FM broadcasting. Description on RDS function 1. PTY(Program Type) : Displays the type of programme currently being broadcast 2. PS NAME(Program Service Name) : Indicates the name of broadcasting station and is composed of 7 characters. 3. RT(Radio Text) : Decodes the text broadcast by a station (if any) and is composed of maximum 64 characters. 4. CT(Clock Time) : Decodes the real time clock from the FM frequency. Some stations may not transmit PTY, RT or CT information therefore this may not be displayed in all cases. 5. TA(Traffic Announcement) : When this symbol flashes it shows that the traffic announcement is in progress. 16 About RDS broadcasting PS NAME RT CT Current FM frequency About RDS DISPLAY function 1 2 3 MP3/CD CD SLEEP EQ/S.BASS TAPE SPEED POWER SOUND DISPLAY PTY RDS MP3/CD CD MO/ST SLEEP EQ/S.BASS TAPE SPEED POWER SOUND DISPLAY PTY RDS MP3/CD CD MO/ST AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED POWER SOUND DISPLAY PTY RDS 1

helps the FM radio to recognize the program type of each FM station. The below 30 PTY information is shown on the display by pressing the Pty button. If the PTY MODE which agrees with the PTY MODE selected in the course of auto-search, isn't received, it is returned to the first frequency at beginning the PTY SEARCH and the auto-search and PTY SEARCH are suspended. About PTY-SEARCH Searches the same PTY as the program type of broadcasting station. Receive the FM radio. See the radio receiving method on the page 14~15. The FM and frequency appear on the display. If the r e received station is transmitting the RDS information, “RDS” lights up. Press the PTY button. The PTY MODE(NEWS, AFFAIRS, etc.) appears on the display. Press the TUNING or button on the front panel to select the desired PTY MODE. If the station is transmitting no PTY information, 'NO PTY' lights on the display. When the PTY MODE is selected(The PTY MODE is shown on the display), press the PTY KEY once again to convert into PTY-SEARCH MODE and auto-search the station sequentially. If the PTY MODE received in the course of auto-search agrees with the selected PTY MODE, the auto-search stops and the PTY-SEARCH is finished. PTY(Program Type) indication and PTY-SEARCH function Display NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP M ROCK M M.O.R.M LIGHT M CLASSIC OTHER M WEATHER FINANCE CHILDRE SOCIAL RELIGIO PHONE I TRAVEL LEISURE JAZZ COUNTRY NATION OLDIES FOLK M DOCUMEN TEST Program Type • News including an announced opinion and report • Several matters including a current incident, documentary, discussion and analysis. • Information including weights and measures, returns and fore- cast, matters interesting the customer, medical information, etc. • Sports • Education • Drama-Radio serial, etc. • Culture-National or local culture including the religious problem, social science, language, theatre,etc. • Natural science and technology • Others-Speech, amusing program (quiz, game), interview, comedy and satirical play, etc. • Pop music • Rock music • M.O.R- Comfortable music, occasionally vocal or piece • Light classical music- Classical music and instrumental and chorus music • Heavy classical music-Orchestra music, symphony, chamber music and opera • Other music - Jazz, R&B country music • Weather • Finance • Children’s programmes • Social affairs • Religion • Phone in • Travel • Leisure • Jazz Music • Country Music • National Music • Oldies Music • Folk Music • Documentary • Alarm Test 1 2 CD SLEEP EQ/S.BASS TAPE SPEED POWER SOUND DISPLAY PTY RDS 2 2 2

You do not need to adjust the volume, as it has no effect on the recording. Switch the system on by pressing Standby/On ( ) . Insert a blank cassette in Deck. Select the TUNER function by pressing TUNER/BAND. Select the radio station that you wish to record by pressing or button on thel front panel or / on the remote control. Press REC/PAUSE. Result: REC is displayed and recording starts. To stop recording, press STOP ( )button. 1 2 3 4 5 6 Recording a Radio Program Switch the system on by pressing Standby/On ( ) . Select the TAPE function by pressing TAPE on the front panel. Open the cassette deck by pushing on the corner of the cover marked PUSH EJECT until you hear a click and then release it. Insert the pre-recorded cassette with the open edge of the tape facing downwards. Close the deck by pushing on it until it clicks into place. Press the TAPE( ) button. Result: The cassette starts playing. Press TAPE SPEED to adjust the speed of the tape playing.And each time the button is pressed,the mode changes as follows. When the cassette is stopped, select one of the following functions as required. To... Press... Rewind the cassette................... / Fast-forward the cassette........... / The cassette player stops automatically when the beginning or end of the cassette is reached. To stop the playback or search, press STOP ( ) button. 18 Listening to a Cassette The direct recording mode enables you to start recording with any track on the compact disc. You do not need to adjust the volume, as it has no effect on the recording. Switch your system on by pressing Standby/On ( ) . Insert a blank cassette in Deck. Load a compact disc. Press the MP3-CD( ) button. Use the CD selection ( , ) buttons to select the desired song. Press the REC/PAUSE button. Result: Recording will begin. To stop recording, press STOP ( ) button. 1 23 4 5 6 Direct recording 1 2 3 4 5 6 7 8 Recording a Compact Disc -10%SPEED +10%SPEED NORMAL 9 1 4 6 4 4 5 3,5 1 8 8 7 2,6 9 1 6 4 4 5 3

Example: You wish to wake up to music every morning. If you no longer want the system to be switched on or off automatically, you must cancel the timer. Before setting the timer, check that the current time is correct. For each step, you have a few seconds to set the required options. If you exceed this time, you must start again. Switch the system on by pressing Standby/On ( ). Press TIMER/CLOCK until TIMER is displayed. Press PROGRAM/SET. Result:ON TIME is displayed for a few seconds, followed by any switch- on time already set; you can set the timer switch-on time. Set the timer switch-on time. a Set the hour by pressing and . b Press PROGRAM/SET. Result: The minutes flash. c Set the minutes by pressing and . d Press PROGRAM/SET. Result: OFF TIME is displayed for a few seconds, followed by any switch-off time already set; you can now set the timer switch-off time. Set the timer switch-off time. a Set the hour by pressing and . b Press PROGRAM/SET. Result: The minutes flash. c Set the minutes by pressing and . d Press PROGRAM/SET. Result: VOL 10 is displayed, where 10 corresponds to the volume already set. Press and to adjust the volume level and press PROGRAM/SET. Result:The source to be selected is displayed. Press and to select the source to be played when the system switches on. If you select... You must also... TAPE (cassette) ........................• Insert a recorded cassette in the deck. TUNER (radio) ..........................• Select the FM or AM (MW/LW) frequency band by pressing and . • Press PROGRAM/SET. • Select a preset station by pressing and . CD (compact disc).......................Load a compact disc. Press PROGRAM/SET to confirm the timer. Press Standby/On to set the system to standby mode. Result: is displayed on the top right of the time, indicating that the timer has been set. The system will switch on and off automatically at the required times. If the timer switch on and off times are identical, the word ERROR is displayed. You can use / button on the front panel instead of / buttonon the remote control in step 4,5,6,7. After having set the timer, it will start automatically as shown by the timer indication on the display. If you no longer wish to use the timer, you must cancel it. You can stop the timer at any time (system on or in standby mode). To... Press TIMER ON/OFF... Cancel the timer........................... Once. Result: is no longer displayed. Restart the timer.......................... Twice. Result: is displayed again. Timer Function Cancelling the Timer 1 3 4 5 6 7 8 2 CD/MP3-CD TAPE TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED TUNING MODE REPEAT VOLUME TUNING/ ALBUM MUTE +10 POWER SOUND DISPLAY PTY RDS 9 1,9 2 3,4,5,6,7,8 4,5,6,7 4,5,6,7 TUNER BAND MO/ST TIMER/CLOCK TIMER ON/OFF AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED MUTE POWER SOUND DISPLAY PTY RDS GB 19

component system so that you can listen to music or radio programs without disturbing other people in the room. The headphones must have a 3.5 mm connector or appropriate adaptor. Connect the headphones to the Phones connector on the rear panel (or top right corner). Result: The loudspeakers are no longer used for sound output. Prolonged use of headphones at a high volume may damage your hearing. You can set the system to switch off automatically. Example: You wish to fall a sleep to music. Press SLEEP on the remote control. Result: The following indications are displayed: Press SLEEP one or more times to indicate how long the system should continue playing before it switches off: At any time, you can: Check the remaining time by pressing SLEEP Change the remaining time by repeating Steps 1 and 2 To cancel the sleep timer function, press SLEEP one or more times until OFF is displayed and the word SLEEP disappears. Sleep Timer MO/ST SLEEP EQ/S.BASS TAPE SPEED POWER SOUND DISPLAY PTY RDS 90 MIN 60 MIN 45 MIN OFF 15 MIN 30 MIN 1 2 3 1,2,3 MUTE Function You can turn the sound off temporarily. Example: You wish to answer a telephone call. Press MUTE. To switch the sound back on (at the same volume as before), press MUTE again, or turn VOLUME button. 1 2 TUNER TIMER/CLOCK TIMER ON/OFF MUTE Power sound function EQ /S.BASS (Super Bass) Function This machine is equipped with the function of POWER SOUND, which amplifies bass treble output to twice as much for powerful surround-sound. Press the POWER SOUND button on the front panel. Result: P.SOUND is displayed for a few seconds. A more powerful resonant sound is diffused. To cancel this function, press POWER SOUND again. Result: OFF is displayed for a few seconds. Your Micro Component system has a bass amplification function and equipped with a preset equaliser that allows you to choose the most appropriate balance between treble and bass frequencies , according to the type of music you are listening to.That is called EQ/S.BASS. This function makes the sound more powerful and real. Press EQ/S. BASS on the front panel or EQ/S. BASS on the remote control until the required option is selected. To obtain a... Select... Normal balance (linear)............................................PASS Balance suitable for pop music............................POP Balance suitable for rock music ..........................ROCK Balance suitable for classic music.......................CLASSIC Balance suitable for s-bass music.......................S-BASS 1 2 20 CD BAND MO/ST AUX PROGRAM/SET REP. A B SLEEP EQ/S.BASS TAPE SPEED POWER SOUND DISPLAY PTY RDS

micro-component system, you must clean the following elements regularly: The outer casing The compact disc player The cassette players (heads, rollers and drive capstans) Always unplug the system from the wall outlet: Before cleaning it If you are not going to be using it for a long time Outer Casing Clean the outer casing regularly using a soft cloth and a light detergent. Do not use abrasive powders, liquids or aerosol cleaners. Never let any liquids get into the system. Compact Disc Player Before playing a compact disc, clean it with a special CD cleaning agent. Do not use the same cleaning agents as for vinyl LP records. Carefully wipe the disc from the centre outward. Regularly clean the player with a special cleaning disc (available from your local dealer). Tape Decks Press PUSH EJECT( ) to open the cassette deck. Use a cotton bud and a special cassette cleaning agent to clean the: Head (1) Rollers (2) Drive capstans (3) If you will not be using the remote control for a long time, remove the batteries to prevent corrosion. Although your system is very hard-wearing, it should not be used in an excessively dusty environment or subjected to shocks or extreme heat (close to heating appliances or in direct sunlight, etc.). If the unit emits an unpleasant odour when in use, unplug it from the main supply and contact the after-sales service. Cleaning Your Micro-Component System 1 1 2 2 3 2 1 The following diagrams illustrate the precautions to be taken when using or moving your micro-component system. Safety Precautions Ambient operating conditions: Ambient temperature 5°C-35°C Humidity 10-75% Do not expose the unit to direct sun radiation or other heat sources. This could lead to overheating and malfunction of the unit. Do not place potted plants or vases on top of the unit. Moisture entering the unit could lead to dangerous electric shock and can cause equipment damage. In such events immediately disconnect the main plug from the socket. Do not place heavy items on the main lead. Main cable damage can lead to damage of the equipment (fire hazard) and can cause electric shock. Do not remove any equipment panels. The inside of the unit contains live components, which cause electric shock. During thunderstorms, disconnect the main plug from the socket. Main voltage peaks due to light- ning could damage the unit. VOLUME UP DOWN Remove the batteries from the remote control, if not used for any extended period. Leaking batteries can cause serious damage to the remote control. When using headphones, take care not to listen at excessive volumes. Extended use of headphones at high volumes will lead to hearing damage.

If you have any of the problems listed below, try the solutions given. They may save you the time and inconvenience of an unnecessary service call. If the above guidelines do not allow you to solve the problem, take a note of: The model and serial numbers, normally printed on the rear of the system Your warranty details A clear description of the problem Then contact your local dealer or SAMSUNG after-sales service. Problem The system does not work There is no sound The Timer does not work In case it does not work, even the action is taken as above. The compact disc player does not start playing The MP-3 CD player cannot be played. The tape does not start playing The volume falls off The cassette is not erased correctly There is excessive wow and flutter Reception is poor or no radio stations are received at all G E N E R A L C D / M P 3 C D R A D I O C A S S E T T E S Checks/Explanation • The main lead is not correctly plugged into a wall socket or the wall socket is not switched on. • The remote control batteries need replacing or the polarity has not been respected. • The STANDBY/ON button has not been pressed. • The volume has been completely turned down. • The correct function (TUNER, MP3-CD, TAPE, AUX) has not been selected. • You have connected a set of earphones. • The loudspeaker wires have been disconnected. • The MUTE button has been pressed. • The timer has been stopped by pressing TIMER ON/OFF. • Press the POWER SOUND button for 5 seconds in power ‘OFF’(standby), then it is returned the original position (RESET) • The CD function has not been selected. • The disc has been inserted face down or is either dirty or scratched. • The laser sensor is dirty or dusty. • The system has not been installed on a flat, horizontal surface. • Condensation has formed in the player; leave the system in a warm, airy room for at least one hour. • Use the PC to confirm if the extension is *.mp3. • The TAPE function has not been selected. • The cassette has not been inserted correctly. • The cassette player has not been closed. • The tape is either slack or broken. • The audio heads are dirty. • The rollers or drive capstans are dirty. • The tape is worn. • The TUNER function has not been selected. • The radio frequency has not been correctly selected. • The aerial has been disconnected or is not facing the right way. Turn it until you find the best orientation. • You are in a building that blocks radio waves; you must use an outside aerial. Check that the tape in the cassette is sufficiently taut. To prevent erasing a cassette that you wish to keep, remove the safety tab on the upper edge of the cassette. To record a cassette, where the tab has been broken, simply cover the opening with adhesive tape. When you have finished playing a cassette, always put it back in its case. Store your cassettes in a clean place, out of direct sunlight, where they will not be exposed to high temperatures. Avoid using 120-minute cassettes as they place unnecessary strain on the tape mechanism. Handle your compact discs with care. Always hold them by the edges to avoid leaving fingerprints on the shiny surface. When you have finished playing a compact disc, always put it back in its case. Do not fix paper or adhesive tape to the discs and do not write on the label. Clean them with a special-purpose cloth. Store your compact discs in a clean place, out of direct sunlight, where they will not be exposed to high temperatures. Always use compact discs marked . Precautions When Using Compact Discs Before Contacting the After-Sales Service Precautions When Using Audio Cassettes COMPACT DIGITAL AUDIO 22 GB

instructions are thus subject to change without notice. Technical Specifications RADIO LW Usable sensitivity 60 dB AM (MW) Signal/noise ratio 40 dB Usable sensitivity 56 dB Total harmonic distortion 2 % FM Signal/noise ratio 54 dB Usable sensitivity 16 dB Total harmonic distortion 0.5 % COMPACT DISC PLAYER Frequency range 20 Hz - 20 KHz Signal/noise ratio 80 dB (at 1 KHz) with filter Distortion 0.1 % (at 1 KHz) Channel separation 75 dB Disc sizes Diameter: 120 or 80 mm. Thickness: 1.2 mm TAPE DECK Frequency range 125 Hz ~ 8 KHz Signal/noise ratio 40 dB Channel separation 30 dB Erasing effect 50 dB AMPLIFIER Output power (6 Ω) 2 X 10 Watts RMS (total harmonic distortion : 10%) Channel separation 40 dB Signal/noise ratio 70 dB GENERAL Dimensions 145(W) x 226 (H) x 282(D) mm

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. North America Latin America Europe CIS Asia Pacific Middle East & Africa CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) www.samsung.com/mx U.S.A 1-800-SAMSUNG (7267864) www.samsung.com ARGENTINE 0800-333-3733 www.samsung.com/ar BRAZIL 0800-124-421 www.samsung.com/br CHILE 800-726-7864(SAMSUNG) www.samsung.com/cl COSTA RICA 0-800-507-7267 www.samsung.com/latin ECUADOR 1-800-10-7267 www.samsung.com/latin EL SALVADOR 800-6225 www.samsung.com/latin GUATEMALA 1-800-299-0013 www.samsung.com/latin JAMAICA 1-800-234-7267 www.samsung.com/latin PANAMA 800-7267 www.samsung.com/latin PUERTO RICO 1-800-682-3180 www.samsung.com/latin REP. DOMINICA 1-800-751-2676 www.samsung.com/latin TRINIDAD & TOBAGO 1-800-7267-864 www.samsung.com/latin VENEZUELA 1-800-100-5303 www.samsung.com/latin BELGIUM 02 201 2418 www.samsung.com/be CZECH REPUBLIC 844 000 844 www.samsung.com/cz DENMARK 38 322 887 www.samsung.com/dk FINLAND 09 693 79 554 www.samsung.com/fi FRANCE 08 25 08 65 65 (0,15€/Min) www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,12/Min) www.samsung.de HUNGARY 06 40 985 985 www.samsung.com/hu ITALIA 199 153 153 www.samsung.com/it LUXEMBURG 02 261 03 710 www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0.10/Min) www.samsung.com/nl NORWAY 231 627 22 www.samsung.com/no POLAND 0 801 801 881 www.samsung.com/pl PORTUGAL 80 8 200 128 www.samsung.com/pt SLOVAKIA 0850 123 989 www.samsung.com/sk SPAIN 902 10 11 30 www.samsung.com/es SWEDEN 08 585 367 87 www.samsung.com/se U.K 0870 242 0303 www.samsung.com/uk RUSSIA 8-800-200-0400 www.samsung.ru UKRAINE 8-800-502-0000 www.samsung.com/ur AUSTRALIA 1300 362 603 www.samsung.com/au CHINA 800-810-5858, 010- 6475 1880 www.samsung.com.cn HONG KONG 2862 6001 www.samsung.com/hk INDIA 3030 8282 www.samsung.com/in 1600 1100 11 INDONESIA 0800-112-8888 www.samsung.com/id JAPAN 0120-327-527 www.samsung.com/jp MALAYSIA 1800-88-9999 www.samsung.com/my PHILIPPINES 1800-10-SAMSUNG (7267864) www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) www.samsung.com/sg THAILAND 1800-29-3232 www.samsung.com/th 02-689-3232 TAIWAN 0800-329-999 www.samsung.com/tw VIETNAM 1 800 588 889 www.samsung.com/vn SOUTH AFRICA 0860 7267864 (SAMSUNG) www.samsung.com/za U.A.E 800SAMSUNG (7267864) www.samsung.com/mea Region Country Customer Care Center  Web Site