Freescale Semiconductor KIT33903 Operation & User’s Manual

Freescale Semiconductor User’s Guide Document Number: KT33903UG Rev. 1.0, 9/2011 KIT33903 Evaluation Boards Supports KIT33903BD5EVBE (5 Volt)/KIT33903BD3EVBE (3.3 Volt) Figure 1. KIT33903BD5EVBE/KIT33903BD3EVBE Evaluation Boards Table of Contents 1 Kit Contents / Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 EVB Setup Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 Using the EVB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 Schematic Drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 9 Board Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 10 Evaluation Board Bill of Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 11 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2 Freescale Semiconductor Kit Contents / Packing List 1 Kit Contents / Packing List • KIT33903BD5EVBE or KIT33903BD3EVBE Hardware • CD33903 (includes SPIGen Software) • CABLE, RIBBON FLAT 16 PIN ASSY, 0.100" PITCH, 6" LENGTH

Freescale Semiconductor 3 Important Notice 2 Important Notice Freescale provides the enclosed product(s) under the following conditions: This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This EVB may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This EVB is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services. Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit. Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typical”, must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur. Should the Buyer purchase or use Freescale products for any such unintended or unauthorized application, the Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture of the part.Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2011

4 Freescale Semiconductor Introduction 3 Introduction This evaluation board allows the user to implement the functionality of the MC33903 product System Basis Chip (SBC). This EVB includes one I/O test point that can be configured to be pulled up to VSUP or pulled down to GND through a resistor and indicator LED. It is easily configured via jumper settings. The SBC can also be exercised in debug mode (watchdog re-fresh/monitoring not needed) by simply populating a jumper. Specified resistor pull-downs can be implemented on the DBG and MUX pins via simple jumper configurations. The status of I/O0, 5V_CAN, SAFE, and VDD can be visually monitored via on-board LEDs. The CAN and LIN Bus signals are provided through terminal block connectors. An isolated terminal block connector is implemented to provide power to the evaluation board with an external DC power supply. The evaluation boards are operated through the graphical user interface (GUI) paired up with the SPI dongle board (KITUSBSPIDGLEVME) through the 2x8 pin ribbon cable. Additionally, for added flexibility, the user can implement a custom board with a microcontroller to talk to the SBC via the 16 pin header. 3.1 EVB Features • Nominal operating supply voltage range of 5.5 to 27 V • 5.0 V/3.3 V regulator for the MCU with an external PNP ballast transistor to increase current capability • Multiple CAN Bus termination options supported via socket • One high/low side I/O (SPI configurable) accessible through a test point • Status of I/O0 indicated by LED (dependent on jumper configuration) • Debug mode/watchdog configuration via jumper settings • MUX output voltage accessible through a test point and external resistor selectable through a jumper • I_WAKE_I test point to enable a FET and load VDD with current to wake-up the SBC • LIN1_T and LIN2_T test points to monitor I/O voltages (SPI configurable) • I/O0, 5V_CAN, SAFE, and VDD status indicated by LED • 100 mil 2x8 pin standard header connector for SPI communication • 100 mil 16 pin standard header connector for custom MCU board connection

Freescale Semiconductor 5 Required Equipment 3.2 Device Description/Features • Protected 5.0 or 3.3 V regulator for the MCU (part number selectable) with optional external PNP usage to increase current capability for MCU • Fully-protected embedded 5.0 V regulator for the CAN driver • Extremely low quiescent current in low power modes • Multiple under-voltage detections to address various MCU specifications and system operation modes (i.e. cranking) • Multiple wake-up sources in low power modes: CAN or LIN bus, I/O transition, automatic timer, SPI message, and VDD over-current detection • Voltage, current, and temperature protection with enhanced diagnostics that can be monitored by the system via a MUX output • ISO11898-5 high speed CAN interface compatibility for baud rates of 40 kb/s to 1.0 Mb/s. LIN 2.1 and J2602 LIN interface compatibility • Pb-free packaging designated by suffix code EK 4 Required Equipment 4.1 Minimum Required Equipment • Power supply: minimum 5.5 V and 200 mA current • Any piece of equipment/board that is capable of producing TXD and/or CAN and LIN messages • KITUSBSPIDGLEVME (USB-to-SPI Kit) • USB cable • CABLE, RIBBON FLAT 16 PIN ASSY, 0.100" PITCH, 6" LENGTH • USB enabled computer with Windows XP or higher • SPIGen software (Setup.exe)

6 Freescale Semiconductor EVB Setup Configuration 5 EVB Setup Configuration Figure 2. EVB Setup Configuration Diagram

Freescale Semiconductor 7 Hardware Configuration 6 Hardware Configuration The KIT33903BD5EVBE/KIT33903BD3EVBE operates with a single 5.5 V minimum power supply and can be driven with the KITUSBSPIDGLEVME along with its GUI. For added flexibility, it is also possible to develop a custom board to drive this evaluation board via the 16 pin standard header. 6.1 Board Implementation For Standard EVB configuration, set up the jumpers as shown on Figure 3. If the jumper configuration is in accordance with Jumper Connections, on page 8, the VDD (D3) and the 5V_CAN (D4) LEDs must be ON at startup. If CAN communication will be exercised, populate the CAN termination socket (J13) with the necessary components to implement the chosen CAN Termination as shown on Figure 4. JUMPER POSITION J15 1-2 J22 1-2 J23 OPEN J27 1-2 J28 OPEN J9 J22 J2 pSPI Control J1 External Control J23 J27 J12 CAN Termination (Power) CAN Bus J28 J15 CON2 LIN2 Bus CON1 LIN1 Bus Figure 3. Manual Mode Jumper Settings

8 Freescale Semiconductor Hardware Configuration 6.2 Jumper Connections 6.3 CAN Termination Configurations Figure 4. CAN Termination Configurations via J13 Socket Name Description J15 VDD Status Jumper closed -> LED indicator enabled J22 MUX pin output Jumper closed -> external 2.4 kohm resistor pull-down to GND implemented J23 I/O0 configuration 1-2 closed -> 4.7 kohm pull-down resistor to GND and indicator LED implemented 2-3 closed -> 15 kohm pull-up resistor to VSUP and indicator LED implemented J27 DBG configuration Jumper closed -> SBC runs in debug mode (no need to refresh/monitor watchdog) J28 MUST be left open J28 DBG external pull-down resistor configuration Jumper closed -> 47 kohm pull-down resistor to GND implemented J27 MUST be left open

Freescale Semiconductor 9 Hardware Configuration 6.4 Power Supply and Input/Output Connectors The three pin terminal block (J9) serves as the main power terminal to supply a minimum of 5.5 V to operate the KIT33903BD5EVBE/KIT33903BD3EVBE. The CAN, LIN1, and LIN2 bus signals are accessible through the three pin terminal blocks J12, CON1, and CON2 respectively. 6.5 Connector J1 – External Control Pin # Pin Name Description 1 MISO SPI data sent to the MCU. When the CS is high, MISO is high-impedance 2 MOSI SPI data received by the device 3 SCLK Clock input for the Serial Peripheral Interface (SPI) of the device 4 CSB Chip select pin for the SPI. When the CS is low, the device is selected. In Low Power mode with VDD ON, a transition on CS is a wake-up condition 5 TXDC_I CAN bus transmit data input. Internal pull-up to VDD 6 RXDC CAN bus receive data output 7 I_WAKE_I Active high input to enable on-board FET to create a 5.0 mA load on VDD 8 N/C Not Connected 9 VDD 3.3 V/5.0 V output of the main regulators for the Microcontroller supply 10 INTB_I This output is asserted low when an enabled interrupt condition occurs. The output is a push-pull structure 11 RSTB_I This is the device reset output whose main function is to reset the MCU. It has an internal pull-up to VDD. The reset input voltage is also monitored in order to detect external reset and safe conditions 12 TXDL1 LIN1 bus transmit data input. Includes an internal pull-up resistor to VDD 13 RXDL1 LIN1 bus receive data output 14 TXDL2 LIN bus transmit data input. Includes an internal pull-up resistor to VDD 15 RXDL2 LIN2 bus receive data output 16 GND Ground Termination

10 Freescale Semiconductor Hardware Configuration 6.6 Connector J2 – SPI Control 6.7 EVB – KITUSBSPIDGLEVME Interconnection Pin # Pin Name Description 1 TXDC CAN bus transmit data input. Internal pull-up to VDD 2 CSB Chip select pin for the SPI. When the CS is low, the device is selected. In Low Power mode with VDD ON, a transition on CS is a wake-up condition 3 INTB This output is asserted low when an enabled interrupt condition occurs. The out- put is a push-pull structure. 4 MISO SPI data sent to the MCU. When the CS is high, MISO is high-impedance 5 RSTB This is the device reset output whose main function is to reset the MCU. It has an internal pull-up to VDD. The reset input voltage is also monitored in order to detect external reset and safe conditions 6 MOSI SPI data received by the device 7 NC No Connect 8 SCLK Clock input for the Serial Peripheral Interface (SPI) of the device 9 NC No Connect 10 NC No Connect 11 I_WAKE Active high input to enable on-board FET to create a 5.0 mA load on VDD 12 NC No Connect 13 NC No Connect 14 NC No Connect 15 NC No Connect 16 GND Ground termination KIT33903BD5EVBE/KIT33903BD3EVBE -J2 USB-to-SPI Dongle Board - I/O PORT Pin # Pin Name Pin Name Pin # 1 TXDC CNTL2 2 2 CSB CSB 1 3 INTB CNTL1 4 4 MISO SO 3 5 RSTB CNTL0 6 6 MOSI SI 5 7 NC DATA4 8 8 SCLK SCLK 7 9 NC DATA3 10 10 NC CNTL3 9 11 I_WAKE DATA2 12 12 NC VDD 11 13 NC DATA1 14 14 NC REG 3.3V 13 15 NC DATA0 16 16 GND GND 15

Freescale Semiconductor 11 Using the EVB 7 Using the EVB 1. Select Install SPIGen (setup.exe) from the CD33903 Start page and follow the on-screen installation instructions. 2. Connect power supply to the VBAT and GND terminals on the EVB, and build the setup as shown on Figure 2. 3. Ensure the voltages provided are in accordance with the device data sheet and the supply currents are sufficient to supply the device. 4. To use SPIGen, go to the Windows Start menu > Programs > SPIGen, and click on the SPIGen icon. The SPIGen Generic SPI Generator GUI will appear. 5. Go to the Configure menu in the upper left hand corner of the GUI and select Edit Configuration. 6. Select the Enable 33905 Tab in the Part Specific Tabs section on the lower right hand corner of the GUI and then click OK button. 7. Click the SBC MC3390x Family tab. 8. Select MC33903D in the Device section located on top of the GUI window. 7.1 Using SPIGen with the MC33903 Product Evaluating all capabilities of the MC33903 product is made easy with the included SPIGen and respective GUI configuration file.

12 Freescale Semiconductor Using the EVB 7.1.1 Sending Commands to Read Flags Set on SBC Device Status and Flags sections Flags decoded Read device’s Flags and status Read Device Mode – keeps SAFE functionality and exits DEBUG Mode (overrides hardware configuration) Adds command to Sequential Mode sequence Adds all commands on tab to Sequential Mode sequence Figure 5. SPIGen Graphical User Interface (Commands and Flags Decoded) 1. In the Registers and Flags tab, click Flag High and Low sub tab to read the device status and clear flags as shown in Figure 5. 2. Click any of the read device flag status options. 3. Click SEQ to add commands to the Sequential Mode window.

Freescale Semiconductor 13 Using the EVB 7.1.2 Reading and Writing Commands to Exercise SBC and Acquire Its Status General Flags Options to send SPI commands Registers Hexadecimal value of SPI command sent and received Send a Simple Watchdog ‘Go to Normal Mode’ command Stores commands sent in a text file Read General Flags Device Status and Flags sections Adds all commands on tab to Sequential Mode sequence Check to Auto Read all flags every 500ms Device status decoded Register bits [7:0] of corresponding tab address (bits [15:8] not shown) Device Selection Function to be written of corresponding tab Send command as configured to corresponding tab address Read device status and enabled functionality Adds command to Sequential Mode sequence Figure 6. SPIGen Graphical User Interface (Commands and Device Status) 1. In the Registers and Flags tab, click Register address high (b7=1) sub tab to read device status and enabled functionality as shown in Figure 6. 2. Initialize the registers by clicking one of the options Init Vreg / Init Wdog / Init Lin-I/O / Init MISC and then click WRITE. 3. Click WD Refresh to go to Normal mode and then click Single WD Write Command. 4. Click Mode+RM to go to low power mode and then click WRITE.

14 Freescale Semiconductor Using the EVB 7.1.3 Sending Commands to Acquire the Configuration of the SBC Device Status and Flags sections Device Status decoded Adds command to Sequential Mode sequence Adds all commands on tab to Sequential Mode sequence Read device status and enabled functionality Read Device Mode – keeps SAFE functionality and exits DEBUG Mode (overrides hardware configuration) Figure 7. SPIGen Graphical User Interface (Commands and Device Configuration) 1. In the Registers and Flags tab, click Register address low (b7=0) sub tab as shown in Figure 7. 2. Click any of the read device flag status options. 3. Click SEQ to add commands to the Sequential Mode window.

Freescale Semiconductor 15 Using the EVB 7.1.4 Sequential Mode Options to send SPI commands Hexadecimal value of SPI command sent and received Stores commands sent in a text file Inserts a wait time in millisecond increments Removes selected lines from list of commands Allows user to loop between selected command lines Runs loop enabled sequence or single sweep of commands Stores commands sent in a text file Clears all commands from list Allows user to load list of commands in text file format Allows user to change Hexadecimal or delay time value Commands sent and received from the SBC’s MOSI and MISO pins Figure 8. SPIGen Graphical User Interface (Sequential Mode) 1. Click Sequential Mode tab. This window displays all commands in the Sequential Mode sequence as shown in Figure 8. 2. In the Insert Wait text box, enter a wait time in millisecond increments. 3. Click Remove Selected Line to remove selected lines from the list of commnads. 4. Select Loop Enable option to allow loop between selected lines. 5. Click Run to activate the loop enabled sequence or single sweep of commands. 6. Click Save to store commands sent in a text file. 7. Click Load to load list of commands in text file format. 8. Click Clear lists to clear all commands from the list. 9. Enter a value in the text box and click Change Value to change the hexadecimal or the delay time value.

16 Freescale Semiconductor Using the EVB 7.1.5 Automated State Diagram Mode Options to send SPI commands Hexadecimal value of SPI command sent and received Auto read function for continuous device mode status Pre-configured selectable initialization and enabling of device’s features (Mouse over for Information) Automated state diagram (Mouse over for information) Figure 9. SPIGen Graphical User Interface (Automated State Diagram Mode) 1. Click Diagram tab. 2. Select Normal Mode option to enable auto read function for continuous device mode status as shown in Figure 9. 3. Click Init Mode to initialize selected registers. 4. Click Normal Mode to go to normal mode and enable selected registers. 5. Click Low Power Vdd OFF/ON to go to low power mode with selected wake ups.

Standard Split No IO Pin Support ) 0 1 ( ) 0 1 ( ) 5 ( (5) GND GND CANL SPLIT SPLIT (2) (1) CANH (7) (4) (13) (11) (8) (14) DBG Pin Support External MCU Control GND GND USB-SPI Dongle Control CANL SPLIT SPLIT CANH (14) (13) (11) (8) (7) (4) (2) (1) (10) (5) GND SPLIT GND CANH CANL SPLIT (4) (2) (1) (8) (7) (13) (11) (14) Socked supported CAN termination options LIN Channels R25 47K R25 47K R17 2.4K R17 2.4K R2 2.2K R2 2.2K D4 RED LED D4 RED LED 2 1 TP4 TP4 J27 HDR 1X2 J27 HDR 1X2 1 2 R26 10K R26 10K D5 MMSZ8V2T1G D5 MMSZ8V2T1G 2 1 R29 3.3K R29 3.3K R28 22K R28 22K TP6 TP6 C1 0.1 UF C1 0.1 UF TP12 TP12 C11 C11 R33 0 R33 0 R12 60.4 R12 60.4 CON1 PCB 3WAY 250V/16A CON1 PCB 3WAY 250V/16A A 1 B 2 C 3 U1 MC33903D U1 MC3390 SAFE 5 DBG 13 RST 23 INT 24 MOSI 27 SCLK 26 MISO 28 CS 25 I/O0 12 MUX 11 5V_CAN 6 TXD_LIN_1 20 RXD_LIN_1 21 LIN_TERM_1 4 LIN_1 19 TXD_LIN_2 14 RXD_LIN_2 16 LIN_TERM_2 3 LIN_2 17 TXD_CAN 30 RXD_CAN 31 CANH 7 CANL 8 SPLIT 10 GND1 15 GND2 18 GND_CAN 9 EXPAD 33 VSUP 2 VSENSE 22 VDD 29 VE 32 VB 1 D1 MBRS140 D1 MBRS140 2 1 D13 1N4148WS D13 1N4148WS 2 1 J12 PCB 3WAY 250V/16A J12 PCB 3WAY 250V/16A A 1 B 2 C 3 + C5 22UF + C5 22UF CON2 PCB 3WAY 250V/16A CON2 PCB 3WAY 250V/16A A 1 B 2 C 3 TP8 TP8 J9 PCB 3WAY 250V/16A J9 PCB 3WAY 250V/16A A 1 B 2 C 3 TP14 TP14 C9 xxpF 50V C9 xxpF 50V + C21 2.2 UF + C21 2.2 UF C10 xxpF 50V C10 xxpF 50V D9 RED LED D9 RED LED 2 1 R16 4.7K R16 4.7K R32 0 R32 0 E B C Q1 BCP52-16 E B C Q1 BCP52-16 1 3 2 4 R31 0 R31 0 D3 RED LED D3 RED LED 2 1 R3 2.2K R3 2.2K R11 330 R11 330 TP9 TP9 J1 HDR_1X16 J1 HDR_1X16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 C15 C15 C16 C16 C12 C12 J28 HDR 1X2 J28 HDR 1X2 1 2 TP3 TP3 J13 DIP14 J13 DIP14 IO1 1 IO8 8 IO14 14 IO7 7 IO4 4 IO11 11 IO2 2 IO3 3 IO5 5 IO6 6 IO9 9 IO10 10 IO12 12 IO13 13 C20 0.1 UF C20 0.1 UF D10 RED LED D10 RED LED 2 1 R15 1K R15 1K R27 1K R27 1K R24 1K R24 1K Q3 MMBF0201NLT1G Q3 MMBF0201NLT1G 1 2 3 TP5 TP5 J22 HDR 1X2 J22 HDR 1X2 1 2 TP11 TP11 R23 1K R23 1K R18 4.7K R18 4.7K C14 C14 + C2 10UF 50V + C2 10UF 50V TP10 TP10 TP7 TP7 R13 60.4 R13 60.4 D14 1N4148WS D14 1N4148WS 2 1 TP13 TP13 R30 0 R30 0 J15 HDR 1X2 J15 HDR 1X2 1 2 J23 HDR_1X3 J23 HDR_1X3 1 2 3 TP1 TP1 C17 C17 TP19 TP19 R14 120 R14 120 TP21 TP21 D8 RED LED D8 RED LED 2 1 J2 HDR_2X8 J2 HDR_2X8 1 2 3 4 6 5 7 8 9 10 11 12 13 14 15 16 C6 0.1 UF C6 0.1 UF TP17 TP17 TP15 TP15 R19 15K R19 15K C13 C13 TP16 TP16 KIT33903 Evaluation Boards, Rev. 1.0 Freescale Semiconductor 17 Schematic Drawing 8 Schematic Drawing Figure 10. Schematic Drawing

18 Freescale Semiconductor Board Layout 9 Board Layout 9.1 Assembly Drawing Figure 11. Assembly Drawing 9.2 Top Side Layer Figure 12. Top Side Layer

Freescale Semiconductor 19 Board Layout 9.3 Bottom Side Layer Figure 13. Bottom Side Layer

20 Freescale Semiconductor Evaluation Board Bill of Material 10 Evaluation Board Bill of Material Freescale does not assume liability, endorse or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their applications. Item Qty Schematic Label Value Description Vender Mfg. PN 1 4 CON1, CON2, J9, J12 PCB 3WAY 250V/16A CON 3 TB TH 5MM SN CAMDEN ELEC- TRONICS LTD CTB5000/3 2 3 C1, C6, C20 0.1 UF CAP CER 0.1UF 50V 10% X7R 0805 KEMET C0805C104K5RAC 3 1 C2 10UF CAP ALEL 10UF 50V 20% SMT (CASE D) PANASONIC EEE1HA100SP 4 1 C5 22UF CAP ALEL 22UF 16V 20% -- CASE C SMT PANASONIC EEE1CA220SR 5 2 C9, C10 xxpF 6 1 C11 1000PF CAP CER 1000PF 50V 5% C0G 1206 AVX 12065A102JAT2A 7 6 C12, C13, C14, C15, C16, C17 56PF CAP CER 56PF 50V 5% C0G 1206 KEMET C1206C560J5GACT U 8 1 C21 2.2 UF CAP ALEL 2.2UF 35V 20% -- SMT PANASONIC EEEFC1V2R2R 9 1 D1 MBRS140 DIODE SCH PWR RECT 1A 40V SMB ON SEMICONDUC- TOR MBRS140T3G 10 5 D3, D4, D8, D9, D10 RED LED LED RED SGL 30MA SMT 0805 LUMEX SML-LXT0805IW-TR 11 1 D5 MMSZ8V2T1G DIODE ZNR -- 0.5W 8.2V SOD123 ON SEMICONDUC- TOR MMSZ8V2T1G 12 2 D13, D14 1N4148WS DIODE SW 150MA 53V SOD-323 DIODES INC 1N4148WS-7-F 13 1 J1 HDR_1X16 HDR 1X16 TH 100MIL SP 330H AU SAMTEC TSW-116-07-S-S 14 1 J2 HDR_2X8 HDR 2X8 TH 100MIL CTR 330H AU SAMTEC TSW-108-07-G-D 15 1 J13 DIP14 SKT DIP 14 PINS TH 3M ICE-143-S-TG30 16 4 J15, J22, J27, J28 HDR 1X2 HDR 1X2 TH 100MIL SP 330H SN SAMTEC TSW-102-07-T-S 17 1 J23 HDR_1X3 HDR 1X3 TH 100MIL SP 330H AU SAMTEC HTSW-103-07-S-S 18 1 Q1 BCP52-16 TRAN PNP PWR 1A 60V SOT-223 PHILIPS SEMICON- DUCTOR BCP52-16 19 1 Q3 MMBF0201NLT1G TRAN NMOS PWR 0.3A 20V SOT23 ON SEMICONDUC- TOR MMBF0201NLT1G 20 2 R2, R3 2.2K RES MF 2.2K 1/8W 5% 0805 BOURNS CR0805-JW-222ELF 21 1 R11 330 RES MF 330 OHM 1/8W 5% 0805 VISHAY INTER- TECHNOLOGY CRCW0805330RJNE A 22 2 R12, R13 60.4 RES MF 60.4 1/10W 1% 0603 KOA SPEER RK73H1JTTD60R4F 23 1 R14 120 RES MF 120 OHM 1/8W 5% 0805 KOA SPEER RK73B2ATTD121J 24 3 R15, R23, R24 1K RES TF 1.0K 1/8W 5% RC0805 BOURNS CR0805JW102E 25 2 R16, R18 4.7K RES MF 4.7K 1/8W 5% 0805 VENKEL COMPANY CR0805-8W-472JT 26 1 R17 2.4K RES MF 2.4K 1/8W 1% 0805 YAGEO AMERICA 232273462402L 27 1 R19 15K RES MF 15K 1/8W 5% 0805 BOURNS CR0805JW153ELF 28 1 R26 10K RES TF 10K 1/8W 5% RC0805 BOURNS CR0805JW103E 29 1 R25 47K RES TF 47K 1/8W 5% RC0805 BOURNS CR0805JW473E 30 1 R27 1K RES TF 1.00K 1/8W 1% RC0805 BOURNS CR0805FX1001E 31 1 R28 22K RES MF 22K 1/8W 5% 0805 BOURNS CR0805-JW-223ELF 32 1 R29 3.3K RES MF 3.3K 1/8W 5% 0805 BOURNS CR0805-JW-332ELF 33 6 R30, R31, R32, R33, R34, R35 0 RES MF ZERO OHM 1/8W -- 0805 BOURNS CR0805-J/-000ELF 34 18 TP1, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP19, TP21 TEST POINT BLACK TEST POINT PIN .100 X .45 BLACK TH COMPONENTS CORPORATION TP-105-01-00 Freescale IC 35 1 U1 MC33903D IC XCVR CAN DUAL LIN 40-1000KBPS 4.4-40V SOIC54 FREESCALE SEMI- CONDUCTOR MCZ33903BD3EK MCZ33903BD5EK

Freescale Semiconductor 21 References 11 References Following are URLs where you can obtain information on other Freescale products and application solutions: Description URL Data Sheet www.freescale.com/files/analog/doc/data_sheet/MC33903_4_5.pdf Fact Sheet www.freescale.com/files/analog/doc/fact_sheet/MC33903_4_5FS.pdf Application Note www.freescale.com/files/analog/doc/app_note/AN3865.pdf Errata http://www.freescale.com/files/analog/doc/errata/MC33903_4_5ER.pdf SPIGen www.freescale.com/files/soft_dev_tools/software/device_drivers/SPI- Gen.html Freescale’s Web Site www.freescale.com Freescale’s Analog Web Site www.freescale.com/analog Freescale’s Power Management Web Site www.freescale.com/powermanagement Freescale’s Automotive Applications Web Site www.freescale.com/automotive

Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 [email protected] Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2011. All rights reserved. KT33903UG Rev. 1.0 9/2011 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part.