Troy-Bilt 682J-Horse Operator's Manual

PartsList REF PART No. No. DESCRIPTION QTY. TRANSMISSIONCOVER& SHIFTLEVER BRACKETASSE_,'IBLIES 1 1186299 Bolt-hex hd., #10-32 x 3/8", selfqocking flange ..................... 3 2 GW-9463 Knob-tines/PTO clutch iever, tapered,plastic .......................... 1 3 GW-2124 Detent Plate-tines/PTOclutch lever 1 4 777120945 DecaI-operating instructions, detent plate................................ 1 5 1186349 Bolt-flanged hex hd., 3/8-16 x 1-1/2". ......................... 4 7 1186329 Bolt-flanged hex hd., 5/16-18 x 3/4", Grade5 ............ 1 9 736-0275 Washer-flat, 5/16" ...

Before operating your machine, ¢arefuJJy read and understand aJJ safety, controls, operating instructions in this Manual, the separate Engine Owner's Manual and on the decals on the machine. Failure to fellow these instructionscan result in seriuus persunalinjury. /F Jntreduetion This section describes the location and function of the controls andfeatures on your tiiier. Referto Section 4, Operation for detaiied operating instructions. Practice using these controis, with the engine shut off, untii you completely understandthe operation of the controls and feel confident with e ...

gentiy movethe wires aside if this condition occurs. 4. Raisehandlebars to one of two height settings andtiglrten the height adjustment lever. Also, makesure ali other mounting hardware is securely tightened. Left-Side Clamp and Nat Figure 2=3. Fully assembled handle- bars. NOTE: Fully assembled handlebar assembly should appearas shown in Figure2=3. STEP 3: Meve Tiller Off Shipping Piatferm 1. Set the DepthRegulator Lever (A, Figure2=4)to Travel position. Do this by lifting the tiiier by the handiebars,then puiiing straight back on the ievm ...

!MpORTANT_ For COrre_twheel speed and be!t range _hoiees when es!ng attachments m' accessories ether than tinee, read the OwneriOperater t_lanual previdedwith the altochment er aeee_sery, SLOWGEAR,LOWBELTRANGE For: ,,Tilling insod, oTilling in hardclay'. oTilling understandingcorn° stalks intough soil conditions. oTilling undercovercrops. o Preparinga deepseedbed. oTilling instony soil. oTilling underresiduesand organic matter. Mixing in fertilizers, manure. SLOWGEAR,NIGHBELTRANGE For: oTilling insod or hardclay. oTilling understandingc ...

oil level check plug, Gear oil should seep out if the level is sufficient. 3. If the oil level is correct, oil will seep out of the check hole (allow extra time in coId weather). If it does,tire Ieveiis fine and you should repIacethe check piug. If no eli seepsout, seeAdding or Changing GearOff. Checking the Tine Attachment Oil Level iMPORTANT: Two different gear oil checking procedures for the tine attach= meet transmission are described next. Use the first procedure if the dipstick in your tine attachment has onty a 'Check Cold' marking. Usethe second procedure i ...

to a ¢ompmetestop, disconnect sparkplug wire and move wire away from spark plug. Remove ignition key, if so equipped, Failure to follow these instructionscan result in serious persenaminjuryor propertydamage. Tighten Bolts and Nuts Checkfor loose or missing hardware every ten (10) operating hours. Failureto tighten or replacefasteners can cause poor performance, equipment damage or oii leakage. Seeyour PartsCataiogfor complete fastener descriptions. Most hardware on your tiiier is ...