Denver DVH-1240M Operating Manual

1.WHEN RECORDING TO USB STICK OR EXTERNAL HARDDISC ON THIS MODEL , YOU HAVE TO WAIT A FEW SECONDS BEFORE PUSHING REC. AFTER INS ERTING THE MEDIA. OTHERWISE THE UNIT CAN FREEZE IN THE SIGNAL. IF THAT HAPPENS, THEN PLEASE TAKE OFF POWER AND CONNECT AGAIN TO FIX THIS. 2.WHEN DIGITAL AUDIO OUTPUT IS SET TO RAW IT IS FOR USING WITH SURROUND RECEIVER ONLY. YOU HAVE TO MUTE THE SOUND ON THE TV WHEN ON THIS MODE, OTHERWISE YOU CAN HAVE SOME NOISE IN THE TV SPEAKERS. IF USING ONLY WITH TV, THEN PLEASE MAKE SURE THE AUDIO OUTPUT IS SET TO PCM. 3.AUTO STANDBY FUNCTION: THIS FUNCTION SHUTS DOWN AUTOMATICALLY AFTER 3 HOURS IF NO USER INTERFERENCE HAS BEEN DONE DURING THESE HOURS. 2 MINUTES BEFORE SHUTDOWN A WARNING MESSAGE WILL BE SHOWN ON THE TV. AUTO STANDBY FUNCTION ARE PRESET TO ON FROM FACTORY SIDE, BUT CAN BE TURNED OFF IN THE SYSTEM MENU. 4.WHEN USING AN EXTERNAL HARDDISC, PLEASE MAKE SURE YOU HAVE FORMATTED IT IN FAT OR FAT32 FILESYSTEM.. NTFS WON’T WORK. AND THE HARDDISC NEED AN EXTERNAL POWER SUPPLY TO WORK, AS THE USB PORT WON’T GIVE ENOUGH POWER TO RUN IT PROPERLY.

The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage. Always read the safety instructions carefully Keep this Instruction Manual for future reference Keep this device away from humidity Lay this device on a reliable flat surface before setting it up D o not stand it on soft furnishings If any of the following situation arises, get the Set Top Box checked by a service technician: It has been exposed to moisture It has been dropped and damaged It has obvious sign of breakage It has not been working well or you cannot get it to work according to the Instruction Manual Warning To prevent the risk of electric shock, do not open the cover or the back of the receiver. Do not block the ventilation holes of the device. Leave appropriate gap above and around it to allow for adequate ventilation. Do not place the device in an unventilated cabinet or on top of a unit which emits heat. Copyright Statement No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies. 1 The power cable/disconnect device shall remain easy to operate/disconnect.

Front Panel Rear Panel 2 DVD DVB POWER BUTTON DISC TRAY USB PLAY/PAUSE EJECT DVD/DVB STOP NEXT PREV

3 4.GOTO Select the track or time point you want. 5.DISC/USB Switch DISC/USB 6.DVD/DVB Switch DVD/DVB. 9.SETUP Access or remove setup menu. 10.REPEAT Repeat chapter/track/title/all. 11.EXIT(DVB) Used to return to the previous screen or menu in DVB.

Remove the battery cover from the Remote Control and put 2xAAA size batteries inside the compartment. The diagram inside the Battery Compartment shows the correct way to install the batteries. OPEN CLOSE 1.Open the cover 2.Install batteries 3.Close the cover 5

OSD Language You can select your own preferred language seetings. Angle Mark Displays current angle setting information on the right hand corner of the TFT screen if available on the disc. Screen Saver This function is used to turn the screen saver On or Off. Press SETUP button to get the setup menu. Use direction buttons to select the preferred item. After finishing settings, press SETUP again to normal display. The following menu items can be changed: GENERAL: selects the GENERAL PAGE menu. AUDIO: selects the AUDIO PAGE menu. VIDEO: selects the VIDEO PAGE menu. PREFERENCE : selects the PREFERENCE PAGE menu. General Setup Page - - GENERALSETUP PAGE - - GOTO GENERAL SETUP PAGE TV DISPLAY WIDE ANGLE MARK ON OSD LANGUAGE ENG SCREEN SAVER ON 4:3 PANSCAN 4:3 LETTERBOX 16:9 ON OFF ENGLISH FRENCH GERMAN ITALIAN SPANISH PORTUGUESE ON OFF TV DISPLAY: selects the aspect ratio of the playback picture. 4:3 PANSCAN: if you have a normal TV and want both sides of the picture to be trimmed or formatted to fit your TV screen. 4:3 LETTERBOX: if you have a normal TV. In this case, a wide picture with black bands on the upper and lower portions of the TV screen will be displayed. 16:9:wide screen display. 6

Audio Setup Page -- -- DOWNMIX STR DIGITAL OUTPUT RAW DOLBY DIGITAL LT/RT STEREO SPDIF/OFF SPDIF/RAW SPDIF/PCM DUAL MONO DYNAMIC STR STR L-MONO R-MONO MIX-MONO --------- --------- FULL OFF - - - - - AUDIO SETUP PAGE GO TO AUDIO SETUP PAGE Downmix This options allows you to set the stereo analog output of your DVD Player. LT/RT :Select this option if your DVD Player is connected to a Dolby Pro Logic decoder. Stereo :Select this option when output delivers sound from only the two front speakers. Digital Output The function is used to select the SPDIF Output:SPDIF Off,SPDIF /RAW,SPDIF/PCM. SPDIF Off: Turns off the SPDIF output. SPDIF/RAW: If you have connected your DIGITAL AUDIO OUT to a multi-channel decoder/receiver. SPDIF/PCM: Only if your receiver is not capable of decoding multi-channel audio. Dolby digital Setup Page The options included in Dolby Digital Setup are: and 'Dynamic '. 'Dual Mono ' Dual Mono Stereo:Left mono sound will send output signals to Left speaker and Right mono sound will send output signals to Right speaker. L-Mono:Left mono sound will send output signals to Left speaker and Right speaker. R-Mono:Right mono sound will send output signals to Left speaker and Right speaker. Mix-Mono:Left and Right mixed mono sound will send output signals to Left and Right speakers. Dynamic Dynamic range compression. 7

- - PREFERENCE SETUP PAGE - - GOTO PREFERENCE PAGE TV TYPE PAL AUDIO ENG SUBTITLE ENG DISC MENU ENG PARENTAL PASSWORD DEFAULT ENGLISH FRENCH GERMAN SPANISH ITALIAN PORTUGUESE ENGLISH FRENCH GERMAN SPANISH ITALIAN PORTUGUESE ENGLISH FRENCH GERMAN SPANISH ITALIAN PORTUGUESE 1 KID SAF 2 G 3 PG 4 PG13 5 PGR 6 R 7 NC17 8 ADULT CHANGE RESET PAL MULTI NTSC Video Setup Page - - VIDEO SETUP PAGE - - GOTO VIDEO SETUP PAGE VIDEO OUTPUT RGB TV MODE HDMI Setup CVBS RGB YUV PROGRESSIVE INTERLACE - - HDMI SETUP - - HDMI HDMI ON RESOLUTION AUDIO SOURCE AUTO ON OFF 480 I 480 P(720) 576 I 576 P(720) 720 P(50Hz) 720 P(60Hz) 1080 I(60Hz) 1080 P(60Hz) 1080 I(50Hz) 1080 P(50Hz) AUTO PCM Preference Page HDMI Setup page Notes: Please select proper resolution according to your TV.otherwise the TV will have no signal. Preference Page 8

video signal of a NTSC disc and output in PAL format. NTSC-Select this if the connected TV is NTSC system.It will change the video signal of a PAL disc and output in NTSC format. MULTI:Chang the video signal output automatic according to the playing disk format. Audio:Selects a language for audio (if available). Subtitle:Selects a language for subtitle (if available). Disc Menu:Selects a language for disc menu (if available). Parental Some DVDs may have a parental level assigned to the complete disc or to certain scenes on the disc.This feature lets you set a playback limitation level.The rating levels are from 1 to 8 and are country dependent. You can prohibit the playing of certain discs that are not suitable for your children or have certain discs played with alternative scenes. PASSWORD:Change your password,default is1369. Default:Back to the factory setting. Note: If the password has been changed, the parentaland disc lock code will also be changed. The default password(1369)is always active even the password has been changed. N TV Type Selecting the colour system that corresponds to your TV when AV outputs.This DVD Player is compatible with both NTSC and PAL. Preference Page 9

COUNTRY:Select your country of residence. LCN:Set LCN on or off TIME ZONE: a.TIME ZONE : Select Time zone of the country. b.SUMMER TIME: Select Summer timer on or off. AUTO STANDBY: The unit will automatic power off at standby mode if no operation is performed after 3 hours, TV screen will display “power down after 120 seconds”beforeunit power off, select exit button by remote control to cancel standby mode on/off the funtion. CHANGE PASSWORD:Set or change the password for Locked programs. Enter your old Password or the default password '1234'. You will then be asked to enter your new password. To confirm re-enter your new password. SYSTEM INFORMATION:Show some information of the player. FACTORY RESET:Reset the factory setting of player. 10 SYSTEM SETUP VIDEO SETTINGS AUDIO SETTINGS INSTALLATION CHANNEL EDIT OSD LANGUAGE COUNTRY LCN TIME ZONE AUTO STANDBY CHANGE PASSWORD SYSTEM INFORMATION FACTORY RESET Setup Installation Press menu key to enter setup installation.

HD OUTPUT:HD TV programe display mode(1080i, 720p, 576p/480p, 576i/480i, auto). SCREEN RATIO: You must set the display format to either 4:3 ,16:9 or Auto to get the maximum display when watching TV. SCART OUTPUT :Select Scart output mode : CVBS or RGB LR MODE: Select audio output mode : LEFT, RIGHT OR STEREO SPDIF: Select digital audio output mode : PCM or RAW Manual search: Install new channels manually. Auto search: Search and install all channels automatically. Upgrade stb: Upgrade the player. SYSTEM SETUP VIDEO SETTINGS AUDIO SETTINGS INSTALLATION CHANNEL EDIT LR MODE SPDIF SYSTEM SETUP VIDEO SETTINGS AUDIO SETTINGS INSTALLATION CHANNEL EDIT MANUAL SEARCH AUTO SEARCH UPGRADE SIN 11

To edit your programs prefences(favourite, lock, move or delete), as picture 6 1.USB PVR has the following features: -Support one-channel TS recoding -Support scheduled recording and real-time recording -Support program playback -Support playback modes include: pause, fast forward and fast rewind. The storage media supported : -USB adapted hard disk (500mA) -USB disk (depending on the read-write speed, 500mA) -In order to delete recorded files on a USB stick then please connect the USB stick to your computer and then delete the recorded files. The TV program is recorded to file at .PVR format, which can be played back on this unit and PC using a suitable player, but can not be played back on DVD or PDVD. The file system format support : -FAT -FAT 32 2.Before recording Must plus USB disk or USB adapted hard disk (500mA). Press STOP key to stop recording. 12 SYSTEM SETUP VIDEO SETTINGS AUDIO SETTINGS INSTALLATION CHANNEL EDIT TV CHANNEL RADIO CHANNEL SYSTEM SETUP VIDEO SETTINGS AUDIO SETTINGS INSTALLATION CHANNEL EDIT CHANNEL EDIT ADD TO FAV 1 1000 SZTVM01 1001 SZTVM02 1002 SZTVM03 1003 SZTVM04 1004 Data FAVORITE LOCK MOVE DELETE PVR (Personal video recorder)

In the normal play mode, Press ● to enter the recording status. Once video recording starts, the upper left crner will display the recording icon. Press STOP key to stop recording. -Scheduled recording. User may set up scheduled recording by setting the data, time and program. Once the scheduled recording time is reached, The player will switch to the scheduled program automatically for recording. To scheduled recording , Press EPG key, to enter EPG page. select your need record program, press OK key to enter scheduled recording page as picture 4.Recorder file play -Enter USB mode and select video,then open file of USB and select torrget document which is recorder. 13 New Reservation 10/3/2006 17:14 Channel Name Nederland 2 DATE YEAR 2006 MONTH 03 Day 10 START TIME HOUR 16 MINUTE 25 End time HOUR 17 MINUTE 20 Runnlng Mode ONE TIME Reserve Type Rec Event Name Top of the Pops OK SAVE Exit Back Switch Schedule Detall Descrlptor OK New Reservation

suddenly or mosaic Problem Potential Reasons What to do No picture Power isn't connected Connect the power The power switch is not on Switch on the power Screen shows No Signal DVB-T cable not connected Plug in the DVB-T cable Incorrect setting Reset setting No sound from speaker No or incorrect connection with audio cable Connect the audio cable correctly Sound on mute Turn off mute function Incorrect sound track Try another sound track Only sound, no image on the screen No or incorrect connection with AV cable Make sure cables are connected correctly The program is a radio program Press key to shift into TV mode Remote Control is not responding The battery is exhausted Change battery Remote Control is not facing or close enough to the Set Top Box Adjust the position of the Remote Control and move closer to the unit The signal is too weak Strengthen the signal Troubleshooting 14

MPEG2 [email protected] Output Format 576P , 720P, 1080i, 4:3 and 16:9 Output Port HDMI,2XSCART Audio Decoder Format MPEG-1 (layer1&2) Audio output Digital audio: S/PDIF Power Voltage AC 110-240V 50/60Hz Working Power 8W Item Sub Item Parameter Tuner Input Frequency 170~230MHz 470~860MHz RF Input level -25~-82dBm IF Bandwidth 7MHz and 8MHz Modulation QPSK,16QAM,64QAM 0.5W Standby power