Sanyo PLV-60 Owner's Manual

SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. TO THE OWNER SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. G This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam. G This projector should be set in the way indicated. If not, it may result in a fire hazard. G Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. Minimum distance should be taken. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous. G Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes. G If the projector is not to be used for an extended time, unplug the projector from the power outlet. READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. 20cm 50cm 50cm 50cm SIDE and TOP REAR

the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges. Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc... Do not use attachments not recommended by the manufacturer as they may cause hazards. Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating. The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided. Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector. This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company. Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it. Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation. e. If the projector has been dropped or the cabinet has been damaged. f. When the projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons. Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition. Voor de klanten in Nederland Bij dit product zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. AC Power Cord for the United Kingdom : This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over) WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET. The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow ············ Earth Blue ································· Neutral Brown ······························ Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. WARNING : THIS APPARATUS MUST BE EARTHED. ASA The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. AC Power Cord for the United States and Canada : AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician. GROUND THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE. AC POWER CORD REQUIREMENT

FEATURES AND DESIGN 6 BEFORE OPERATION 14 COMPUTER MODE 23 VIDEO MODE 31 SETTING 36 APPENDIX 38 PREPARATION 7 NAME OF EACH PART OF PROJECTOR 7 SETTING-UP PROJECTOR 8 CONNECTING AC POWER CORD 8 POSITIONING PROJECTOR 9 ADJUSTABLE FEET 10 MOVING PROJECTOR 10 CONNECTING PROJECTOR 11 TERMINALS OF PROJECTOR 11 CONNECTING TO VIDEO EQUIPMENT 12 CONNECTING TO COMPUTER 13 TOP CONTROLS AND INDICATORS 14 OPERATION OF REMOTE CONTROL 16 OPERATING RANGE 16 WIRED REMOTE CONTROL OPERATION 17 REMOTE CONTROL BATTERIES INSTALLATION 17 OPERATING ON-SCREEN MENU 18 HOW TO OPERATE ON-SCREEN MENU 18 FLOW OF ON-SCREEN MENU OPERATION 18 MENU BAR 19 SELECTING INPUT SOURCE 23 SELECTING COMPUTER SYSTEM 23 PC ADJUSTMENT 24 AUTO PC ADJUSTMENT 24 MANUAL PC ADJUSTMENT 25 COMPATIBLE COMPUTER SPECIFICATIONS 27 PICTURE IMAGE ADJUSTMENT 28 IMAGE LEVEL SELECT 28 IMAGE LEVEL ADJUSTMENT 29 PICTURE SCREEN ADJUSTMENT 30 SELECTING INPUT SOURCE 31 SELECTING VIDEO SYSTEM 32 PICTURE IMAGE ADJUSTMENT 33 IMAGE LEVEL SELECT 33 IMAGE LEVEL ADJUSTMENT 34 PICTURE SCREEN ADJUSTMENT 35 SETTING MENU 36 MAINTENANCE 38 WARNING TEMP. INDICATOR 38 AIR FILTER CARE AND CLEANING 38 CLEANING THE PROJECTION LENS 38 LAMP REPLACEMENT 39 LAMP REPLACE COUNTER 39 TROUBLESHOOTING 40 TECHNICAL SPECIFICATIONS 42 BASIC OPERATION 20 TURNING ON / OFF PROJECTOR 20 ADJUSTING SCREEN 21 ZOOM ADJUSTMENT 21 FOCUS ADJUSTMENT 21 LENS SHIFT ADJUSTMENT 21 KEYSTONE ADJUSTMENT 21 NO SHOW FUNCTION 22 PICTURE FREEZE FUNCTION 22 SOUND ADJUSTMENT 22 VOLUME ADJUSTMENT 22 MUTE SETTING 22 TRADEMARKS G Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc. G IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc. G Windows and PowerPoint are registered trademarks of Microsoft Corporation. G Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. N Compatibility This projector widely accepts various video and computer input signals including; G 6 Color Systems NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL- N color system can be connected. G Component Video Component video signals, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i- 60, can be connected. G S-Video S-Video signals, such as a S-VHS VCR output signals, can be connected. G Computers IBM-compatible and Macintosh computers up to 1280 x 1024 resolution. N High Resolution Image This projector provides 1366 x 768 dots resolution for computer input and 800 horizontal TV lines. The resolution from computer between XGA (1024 x 768) and SXGA (1280 x 1024) is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots. When the resolution of your computer is over than 1280 x 1024, reset computer output for lower resolution. N Multi-Scan System This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for complicated manual adjustment of frequency and other settings. N Keystone Correction Positioning height of projector may result in distorted images being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images. N Multilanguage Menu Display Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish or Japanese. N One-Touch Auto PC Adjustment Incoming computer video signals are recognized and the best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise. N Digital Zoom (for Computer) Digital Zoom function magnifies the image up to 16 times, allowing you to focus on crucial information at a presentation. N Power Management Power Management function is provided to reduce power consumption while the projector is not in use. This Power Management function operates to turn Projection Lamp off when the projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when the projector detects the signal or any operation button is pressed. This projector is shipped with this function ON. N Motor-driven Lens Shift Projection Lens can be moved up and down with Motor- driven Lens Shift function. This function makes it easy to provide projected image where you want. Zoom and Focus can be also adjusted with Motor-driven operation. N Progressive Scan (for Video) Progressive Scan function converts interlace video signals into progressive scan signals and provide fine picture quality.

BOTTOM BACK HOT AIR EXHAUSTED ! Air blown from Exhaust Vents is hot. When using or installing projector, the following precautions should be taken. G Do not put any flammable object near these vents. G Keep the rear grills at least 3’(1m) away from any object, especially heat-sensitive object. G Do not touch this area, especially screws and metallic parts. This area will become hot while projector is used. This projector detects internal temperature and automatically controls operating power of Cooling Fans. FRONT LAMP COVER ADJUSTABLE FEET AND FEET LOCK LATCHES This projector is equipped with Cooling Fans for protection from overheating. Pay attention to the following to ensure proper ventilation and avoid a possible risk of fire and malfunction. G Do not cover vent slots. G Keep bottom clear of any object. Obstructions may block cooling air. AIR INTAKE VENTS (Side and Bottom) PROJECTION LENS SPEAKERS INFRARED REMOTE RECEIVERS LENS COVER POWER CORD CONNECTOR EXHAUST VENTS TERMINALS AND CONNECTORS MAIN ON / OFF SWITCH TOP CONTROLS AND INDICATORS

or 200-240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single- phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect projector with the peripheral equipment before turning projector on. (Refer to pages 11 ~ 13 for connection.) CAUTION For safety, unplug the AC Power Cord when the appliance is not used. CONNECTING AC POWER CORD Connect AC Power Cord (supplied) to projector. The AC outlet must be near this equipment and must be easily accessible. To the POWER CORD CONNECTOR on pro- jector. Projector side AC Outlet side Ground NOTE ON THE POWER CORD The AC Power Cord must meet the requirement of the country where you use the projector. Confirm the AC plug type with the chart below and the proper AC Power Cord must be used. If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer. To the AC Outlet. (120 V AC) For Continental Europe For the U.S.A. and Canada For the U.K. To the AC Outlet. (200 - 240 V AC) To the AC Outlet. (200 - 240 V AC) MAIN ON / OFF SWITCH

This projector is designed to project on a flat projection surface and it can be focused from 4.43’ (1.35m) ~ 45.9’ (14.0m). Refer to the figure below to adjust the screen size. Width x Height 886 x 498 mm 40” 100” 200” 300” 400” 308” 231” 154” 77” 31” 45.9’ (14.0m) 34.1’ (10.4m) 22.9’ (7.0m) 11.5’ (3.5m) 4.43’ (1.35m) Max. Zoom Min. Zoom 2215 x 1245 mm 4430 x 2490 mm 6644 x 3736 mm 8860 x 4980 mm LENS SHIFT ADJUSTMENT Projection Lens can be moved up and down with Motor-driven Lens Shift function. This function makes it easy to provide the projected image where you want. Refer to P 21 for operation. Highest Lens Shift Lowest Lens Shift H1 H3 H4 Screen Size 40” 100” 200” 300” 400” H2 H1 : H2 = 10.9 : 1 H3 : H4 = 1 : 3.9 RECOMMENDATION Brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide the best image. NOTE Screen size and lens shift ratio on the above charts are standard values and they may change by positioning conditions.

G Do not drop or bump projector, otherwise damages or malfunctions may result. G When carrying projector, use a suitable carrying case. G Do not transport projector by using a courier or transport service in an unsuitable transport case. This may cause damage to projector. To transport projector through a courier or transport service, consult your dealer for best way. MOVING PROJECTOR Use Carry Handle when moving projector. When moving projector, replace Lens Cover and retract Adjustable Feet to prevent damage to Projection Lens and cabinet. When this projector is not in use for an extended period, put it into the case (Dust Cover) supplied with this projector. ADJUSTABLE FEET Picture tilt and projection angle can be adjusted by rotating Adjustable Feet. Projection angle can be adjusted to 9.0 degrees. Lift the front of projector and pull Feet Lock Latches on both sides of projector. 1 ADJUSTABLE FEET FEET LOCK LATCHES Release Feet Lock Latches to lock Adjustable Feet and rotate Adjustable Feet to fine tune position and tilt. 2 To shorten Adjustable Feet, lift the front of projector and pull and undo Feet Lock Latches. Position and keystone distortion of the image can be adjusted using Menu Operation. (Refer to P 21 and 36.) 3

Connect S-VIDEO output from video equipment to this jack. (Refer to P12.) Connect audio output from computer or video equipment to these jacks. (Refer to P12, 13.) AUDIO INPUT JACKS VIDEO INPUT JACKS S-VIDEO INPUT JACK Connect video output to these jacks. Connect composite video output to VIDEO/Y or connect component video outputs to VIDEO/Y, Pb(Cb) and Pr(Cr). (Refer to P12.) Connect computer or video output to these jacks. Connect composite video output to VIDEO/Y, separate video outputs to VIDEO/Y and C/Pb(Cb) or component video outputs to VIDEO/Y, C/Pb(Cb) and Pr(Cr). (Refer to P12, 13.) BNC JACKS Connect computer output to this terminal. (Refer to P13.) RGB TERMINAL This projector has INPUT TERMINALS and OUTPUT TERMINALS on its side for connecting computers and video equipment. Refer to the figure on pages 11 to 13 and connect properly. Connect an external audio amplifier to these jacks. (Refer to P12, 13.) AUDIO OUTPUT JACKS This projector uses a micro processor to control the unit. Occasionally, the micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart the unit. Do not use RESET function excessively. RESET BUTTON When using Remote Control Unit as Wired Remote Control, Connect Remote Control Unit to this jack with Remote Control Cable (supplied). (Refer to page 16, 17.) R/C JACK When controlling this projector by computer, connect your computer to this terminal. SERIAL PORT TERMINAL Connect an external speaker system to this jack. (Refer to P12, 13.) EXTERNAL SPEAKER JACK INPUT 1 RGB SERIAL PORT R/C JACK R-AUDIO-L(MONO) R-AUDIO-L(MONO) S-VIDEO V H/V R B INPUT 2 G VIDEO/Y INPUT 3 C/Pb (Cb) Pr (Cr) VIDEO/Y Pb (Cb) Pr (Cr) R-AUDIO-L (MONO) R-AUDIO-L RESET EXT.SP(8Ω) AUDIO OUT INPUT / OUTPUT TERMINALS

R-AUDIO-L(MONO) S-VIDEO V H/V R B INPUT 2 G VIDEO/Y INPUT 3 C/Pb (Cb) Pr (Cr) VIDEO/Y Pb (Cb) Pr (Cr) R-AUDIO-L (MONO) R-AUDIO-L INPUT 1 RGB SERIAL PORT R/C JACK R-AUDIO-L(MONO) RESET EXT.SP(8Ω) AUDIO OUT Video Source (example) Video Cassette Recorder Video Disc Player Video Cable (RCA x 3) ✽ S-VIDEO Cable Audio Amplifier Audio Speaker (stereo) Audio Cable ✽ (RCA x 2) S-VIDEO Output Audio Amplifier Cables used for connection (✽= Cables are not supplied with this projector.) • Video Cable (RCA x 1) • Video Cable (RCA x 3)✽, (BNC x 1)✽, (BNC x 2)✽ or (BNC x 3)✽ • S-VIDEO Cable • Audio Cable (RCA x 2) • Speaker Cable (Mini x 1 (stereo)) ✽ NOTE : When connecting projector, AC Power Cords of both projector and external equipment should be disconnected from AC outlet. Audio Output External Audio Equipment R L S-VIDEO Y Pb/Cb Pr/Cr VIDEO R L Component video output equipment. (such as DVD player or high-definition TV source.) Composite Video Output Audio Cable (RCA x 2) VIDEO Y Pb/Cb Pr/Cr Y C Component Video Output Separate Video Output Component Video Output EXT. SP Speaker (8Ω/ 2W) Speaker Cable (Mini / stereo) ✽ Video Cable (RCA x 1) Video Cable (BNC x 1)✽ Video Cable (BNC x 2) ✽ Video Cable (BNC x 3) ✽

IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA) VGA Cable Desktop type Laptop type Audio Output MAC Adapter ✽ Set the slide switches accord- ing to the chart on page 43. Cables used for connection (✽= Cables are not supplied with this projector.) • VGA Cable (HDB 15 pin) ✽ • Video Cable (BNC x 5) ✽ • MAC Adapter (in the case of connecting Macintosh computer) ✽ • Audio Cables (RCA x 2) or (RCA x 1 - Mini Plug (mono)) ✽ • Speaker Cable (Mini Plug (stereo)) ✽ Audio Cable (RCA x 2) NOTE : When connecting the cable, AC Power Cords of both projector and external equipment should be disconnected from AC outlet. Turn projector and peripheral equipment on before your computer is switched on. RGB Monitor Output Use either RGB Terminal or G, B, R, H/V and V jacks. Audio Cable (RCA-Mini Plug) ✽ Audio Amplifier Audio Speaker (stereo) Audio Cable ✽ (RCA x 2) Audio Amplifier External Audio Equipment R L EXT. SP Speaker (8Ω/ 2W) Speaker Cable (Mini / stereo) ✽ R L MONO (L) G B R H/V V Monitor Output Video Cable (BNC x 5) ✽ Mini Plug RCA

READY INDICATOR WARNING TEMP. INDICATOR LAMP INDICATOR LAMP REPLACE INDICATOR This indicator lights green when projector is ready to be turned on. And it flashes green in Power Management mode. (P37) This indicator is dim when projector is turned on. And bright when projector is in stand-by mode. This indicator turns to yellow when the life of Projection Lamp draws to an end. (P39) This indicator flashes red when internal projector temperature is too high. (P38) INDICATORS This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top. TOP CONTROLS AND INDICATORS

LENS SHIFT VOLUME FOCUS ZOOM ON-OFF Used to adjust zoom. (P21) Used to select MENU operation. (P18, 19) MENU BUTTON INPUT BUTTON POWER ON–OFF BUTTON FOCUS BUTTONS VOLUME BUTTONS Used to select input source among INPUT 1, 2 or 3. (P23, 31) Used to operate Auto PC Adjustment function. (P24) Used to adjust focus. (P21) Used to adjust volume. (P22) Used to reset to normal picture adjustments preset by the factory or to reset screen adjustment in True mode, Digital Zoom mode or Keystone mode. (P21, 28, 30, 33) Used to move Pointer or to adjust the item on On-Screen MENU. And it is also used to pan image in Digital Zoom mode. (P30) Used to execute the item selected or to expand image in Digital Zoom mode. (P30) Used to turn projector on or off. (P20) ZOOM BUTTONS Used to adjust lens shift. (P21) AUTO PC ADJ. BUTTON SELECT BUTTON NORMAL BUTTON POINT BUTTONS LENS SHIFT BUTTONS TOP CONTROL 15 BEFORE OPERATION

FREEZE IMAGE NO SHOW LENS SHIFT KEYSTONE SELECT NORMAL MENU 16 16.4’ (5 m) 60° 16.4’ (5 m) BEFORE OPERATION OPERATION OF REMOTE CONTROL Used to select input source. (P23, 31) Used to execute the item selected or to expand image in Digital Zoom mode. (P30) POWER ON-OFF BUTTON Used to turn projector on or off. (P20) MENU BUTTON Used to select MENU operation. (P18, 19) SELECT BUTTON INPUT BUTTON Used to move Pointer or to adjust the item on On-Screen MENU. And it is also used to pan image in Digital Zoom mode. (P30) POINT BUTTONS Used to adjust zoom. (P21) MUTE BUTTON Used to mute sound.(P22) ZOOM BUTTONS FOCUS BUTTONS Used to adjust focus. (P21) NO SHOW BUTTON Used to turn picture into black image. (P22) AUTO PC ADJ. BUTTON Use to operate Auto PC Adjustment function. (P24) VOLUME BUTTONS Used to adjust volume. (P22) D.ZOOM BUTTONS Used to select Digital Zoom mode and resize image. (P30) KEYSTONE BUTTON Used to correct keystone distortion. (P21, 36) FREEZE BUTTON Used to freeze picture. (P22) NORMAL BUTTON Used to reset to normal picture adjustments preset by the factory or to reset screen adjustment in True mode, Digital Zoom mode or Keystone mode. (P21, 28, 30, 33) WIRED REMOTE JACK When using as Wired Remote Control, connect Remote Control Cable to this jack. (P17) LENS SHIFT BUTTON Used to select LENS SHIFT function. (P21) IMAGE BUTTON Use to select IMAGE level. (P28, 33) 60° OPERATING RANGE Point Remote Control toward projector (Remote Receiver) whenever pressing the buttons. Maximum operating range for Remote Control is about 16.4’ (5m) and 60° in front and rear of projector. Remote Control Unit can be used as either Wired or Wireless.

upward. Press the lid downward and slide it. Remove the battery compartment lid. Slide 2 batteries into the compartment. Replace the compartment lid. REMOTE CONTROL BATTERIES INSTALLATION Two AA size batteries For correct polarity (+ and –), be sure the battery terminals are in contact with pins in the compartment. WIRED REMOTE CONTROL OPERATION When using this Remote Control Unit as Wired Remote Control, Connect Remote Control Unit to R/C JACK with Remote Control Cable (supplied). Batteries installation is required when using as Wired Remote Control Unit. INPUT 1 R/C JACK Remote Control Cable (supplied) To insure safe operation, please observe the following precautions : G Use (2) AA, UM3 or R06 type alkaline batteries. G Replace two batteries at the same time. G Do not use a new battery with a used battery. G Avoid contact with water or liquid. G Do not expose Remote Control Unit to moisture, or heat. G Do not drop Remote Control Unit. G If batteries have leaked on Remote Control Unit, carefully wipe the case clean and load new batteries.

FLOW OF ON-SCREEN MENU OPERATION Display ON-SCREEN MENU Press MENU button to display ON-SCREEN MENU (MENU BAR). A red frame is POINTER. Move POINTER (red frame) to MENU ICON that you want to select by pressing POINT RIGHT / LEFT buttons. Adjust ITEM DATA by pressing POINT buttons. Refer to the following pages for details of respective adjustments. Press POINT DOWN button and move POINTER (red frame or red arrow) to ITEM that you want to adjust, and then press SELECT button to show Item Data. Select item to be adjusted Control and adjust through ON-SCREEN MENU 1 2 4 3 You can control and adjust this projector through ON- SCREEN MENU. Refer to the following pages to operate each adjustment on ON-SCREEN MENU. 2 MOVING POINTER 3 SELECT ITEM Move the pointer (✽see below) or adjust the value of item by pressing POINT button(s) on Top Control or on Remote Control Unit. Select the item by pressing SELECT button. Used to select the item. SELECT BUTTON Used to move the Pointer UP/ DOWN/ RIGHT/ LEFT. POINT BUTTONS REMOTE CONTROL OPERATING ON-SCREEN MENU ✽Pointer is the icon on ON-SCREEN MENU to select the item. See the figures on the section "FLOW OF ON- SCREEN MENU OPERATION" below. INPUT MENU SELECT NORMAL AUTO PC ADJ. L Used to select the item. SELECT BUTTON Used to move the Pointer UP/ DOWN/ RIGHT/ LEFT. POINT BUTTONS TOP CONTROL MENU BAR POINTER (red frame) MENU ICON ITEM DATA Press POINT LEFT/RIGHT buttons to adjust the value. SELECT BUTTON POINTER (red frame) Press POINT DOWN button to move POINTER. 1 DISPLAY MENU Press MENU button to display ON-SCREEN MENU. ITEM

computer system. (Refer to P23, 24) IMAGE ADJUST MENU Used to adjust computer image. [Contrast / Brightness / White Balance (R/G/B) / Gamma] (Refer to P29) SETTING MENU Used to change settings of projector and reset Lamp Replace Counter. (Refer to P36, 37) INPUT MENU Used to select input source among INPUT 1, 2, or 3. (Refer to P23) SCREEN MENU Used to adjust size of image. (Refer to P30) IMAGE SELECT MENU Used to select image level among Standard, Real or Image 1 ~ 4. (Refer to P28) FOR PC SOURCE Press MENU BUTTON for PC input source. SYSTEM MENU Used to select system of selected video source. (Refer to P32) IMAGE ADJUST MENU Used to adjust picture image. [Contrast / Brightness / Color / Tint / White balance / Sharpness / Gamma / Noise Reduction / Progressive] (Refer to P34) FOR VIDEO SOURCE Press MENU BUTTON for VIDEO input source. Same function as the Computer Mode. INPUT MENU Used to select input source among INPUT 1, 2, or 3, and to select video source. (Refer to P31) PC ADJUST MENU Used to adjust parameters to match with input signal format. (Refer to P24-26) IMAGE SELECT MENU Used to select image level among Standard, Cinema or Image 1 ~ 4. (Refer to P33) SCREEN MENU Used to set size of image to Full, Zoom, Normal or Wide zoom. (Refer to P35) GUIDE WINDOW Shows selected item of ON- SCREEN MENU. Same function as the Computer Mode.

Connect the projector's AC Power Cord into an AC outlet and turn MAIN ON / OFF SWITCH to ON. LAMP Indicator lights RED, and READY Indicator lights GREEN. Press POWER ON-OFF button on Top Control or on Remote Control Unit to ON. LAMP Indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and the count-down starts. The signal from the PC or Video source appears after 30 seconds. 2 3 TURNING OFF THE PROJECTOR Press POWER ON-OFF button on Top Control or on Remote Control Unit, and the message "Power off?" appears on a screen. Press POWER ON-OFF button again to turn off projector. LAMP Indicator lights bright and READY Indicator turns off. After projector is turned off, Cooling Fans operate (for 90 seconds). During this "Cooling Down" period, this appliance cannot be turned on. 1 2 TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. TURNING ON / OFF PROJECTOR When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again. When WARNING TEMP. Indicator continues to flash, follow procedures below: 1. Turn MAIN ON / OFF SWITCH to OFF and disconnect the AC Power Cord from a AC outlet. 2. Check Air Filters for dust accumulation. 3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.) 4. Turn projector on again. If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center. 1 Complete the peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to "CONNECTING TO PROJECTOR" on Pages 11~13 for connecting that equipment.) 3 When projector has cooled down, READY Indicator turns to green again and you can turn projector on. After cooling down completely, turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord. 30 Preparation Display disappears after 30 seconds. Power off? Message disappears after 4 seconds. When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on page 37. NOTE : When “On start” function is ON, this projector is turned on automatically by switching MAIN ON / OFF SWITCH on. (Refer to page 37.)

Keystone on SETTING Menu (P36). The message “Keystone” is displayed. 2 Correct keystone distortion by pressing POINT UP/DOWN button(s). Press POINT UP button to reduce upper part of the image, and press POINT DOWN button to reduce lower part of the image. To reset Keystone adjustment, press NORMAL button. Message disappears after 4 seconds. Reduce the upper width with POINT UP button. Reduce the lower width with POINT DOWN button. Keystone If image has keystone distortion, correct image with KEYSTONE adjustment. BASIC OPERATION ADJUSTING SCREEN Message disappears after 4 seconds. Message disappears after 4 seconds. Zoom Focus ZOOM ADJUSTMENT FOCUS ADJUSTMENT Message disappears after 4 seconds. Lens shift LENS SHIFT ADJUSTMENT 1 Press LENS SHIFT L/M button(s) on Top Control or LENS SHIFT button on Remote Control Unit. The message “Lens shift” is displayed. 2 Press LENS SHIFT L button or POINT UP button to move image up, and press LENS SHIFT M button or POINT DOWN button to move image down. Refer to P9 for operating range. 1 Press ZOOM L/M button(s) on Top Control or on Remote Control Unit. The message “Zoom” is displayed. 2 Press ZOOM L button or POINT UP button to make image larger, and press ZOOM M button or POINT DOWN button to make image smaller. 1 Press FOCUS L/M button(s) on Top Control or on Remote Control Unit. The message “Focus” is displayed. 2 Adjust focus of the image by pressing FOCUS L/M button(s) or POINT UP/DOWN button(s) .

button again or press any other button. Press NO SHOW button on Remote Control Unit to black out the image. To restore to normal, press NO SHOW button again or press any other button. NO SHOW FUNCTION PICTURE FREEZE FUNCTION Message disappears after 4 seconds. No show Press VOLUME (+/–) button(s) on Top Control or on Remote Control Unit to adjust volume. Volume dialog box appears on the screen for a few seconds. (+) button to increase volume, and (–) button decreasing. Press MUTE button on Remote Control Unit to cut off sound. To restore sound to its previous level, press MUTE button again or press Volume (+/–) button(s). Indicates the roughly level of volume. Press MUTE button to set Mute function On or Off. The display disappears after 4 seconds. SOUND ADJUSTMENT

MENU OPERATION DIRECT OPERATION Choose either Input 1 or Input 2 by pressing INPUT button on Top Control or on Remote Control Unit. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon. Press POINT DOWN button to move a red arrow pointer to either Input 1 or Input 2 that you want to choose and then press SELECT button. When choosing Input 2, Source Select Menu will appear. Move POINTER to RGB and then press SELECT button. (Input 2 accepts R, G, B, H/V and V computer signals (P 13).) 1 2 INPUT button Input 1 Input 2 Input 3 Move POINTER (red arrow) to Input 1 or 2 and press SELECT button. INPUT 2 Move POINTER to RGB and press SELECT button. Source Select Menu (Input 2) INPUT MENU INPUT Menu icon SELECTING COMPUTER SYSTEM This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to “COMPATIBLE COMPUTER SPECIFICATION” on page 27). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually.) Note : Projector may display one of the following messages. When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and the message “AUTO PC Adj.” is displayed on SYSTEM icon. When image is not provided properly, manual adjustment is required. (Refer to P25 and 26.) There is no signal input from computer. Make sure the connection of computer and projector is set correctly. (Refer to TROUBLESHOOTING on page 40.) AUTO PC Adj. No signal SYSTEM Menu icon Displays system being selected. SYSTEM MENU

Auto PC Adjustment function is provided to automatically adjust Fine sync., Total dots, and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows. NOTE : Auto PC Adjustment function cannot be operated when “RGB,” “HDTV720p,” “HDTV1035i” or “HDTV1080i” is selected on SYSTEM Menu (P23, 24). Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. 1 2 Press POINT DOWN button to move a red frame pointer to AUTO PC Adj. icon and then press SELECT button. This Auto PC Adjustment can be executed by pressing AUTO PC ADJ. button on Top Control or on Remote Control Unit. Move a red frame pointer to AUTO PC Adj. icon and press SELECT button. PC ADJUST MENU Fine sync, Total dots and Picture Position of some computers may not be fully adjusted with Auto PC Adjustment function. When the image is not provided properly through this function, manual adjustment is required. (Refer to page 25, 26.) Auto PC Adj. PC ADJUST Menu icon 24 COMPUTER MODE SELECT COMPUTER SYSTEM MANUALLY SYSTEM Menu icon Displays system being selected. The systems on this dialog box can be selected. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SYSTEM icon. Press POINT DOWN button to move a red arrow pointer to the system that you want to set, and then press SELECT button. 1 2 When this mark is displayed as black, more computer system modes will be available. Move the arrow to this mark and then press SELECT button, and the other modes will be displayed. SYSTEM MENU Custom Mode (1~5) set in PC ADJUST Menu. (P25, 26) This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually. Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in SYSTEM Menu (above). Refer to step 3 of MANUAL PC ADJUSTMENT section (P26).

This projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi- Scan system of this projector. If this happens, projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. Note : This PC ADJUST Menu cannot be operated when “RGB” is selected on SYSTEM Menu (P23, 24). Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. 1 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button. Adjustment dialog box will appear. Press POINT LEFT/RIGHT button to adjust the value. Move the red frame icon to the item and press SELECT button. PC ADJUST MENU PC ADJUST Menu icon Adjust the picture as necessary to eliminate flicker from the display. Press POINT LEFT/RIGHT button to adjust value.(From 0 to 255.) Fine sync The number of total dots in one horizontal period. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image. Total dots Adjust horizontal picture position. Press POINT LEFT/RIGHT button(s) to adjust the position. Horizontal Adjust vertical picture position. Press POINT LEFT/RIGHT button(s) to adjust the position. Vertical Press SELECT button to show the information of computer selected. Current mode The number of the total horizontal lines. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image. Total lines Adjusts clamp level. When the image has a dark bar(s), try this adjustment. Clamp Press SELECT button at this icon to adjust “Total lines,” “Clamp,” “Display area,” “Horiz. scale” or “Vert. scale” . Press POINT LEFT/RIGHT button to adjust the value. Press SELECT button at Current mode icon to show the information of computer connected. Shows the status (Stored/Free) of Mode. Selected Mode

cannot be adjusted when “HDTV1035i” or “HDTV1080i” is selected on SYSTEM Menu (P23, 24). Fine sync and Total dots cannot be fully adjusted when “HDTV1035i” or “HDTV1080i” is selected on SYSTEM Menu (P23, 24). Selects area displayed with this projector. Select the resolution at the Display area dialog box. Display area Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) and adjust number to match the resolution of image. Display area H Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) and adjust number to match the resolution of image. Display area V Adjustment of width of image. Press POINT LEFT/RIGHT button(s) for adjustments. Horizontal scale Adjustment of height of image. Press POINT LEFT/RIGHT button(s) for adjustments. Vertical scale Press SELECT button at Display area icon and the Display area dialog box appears. Reset Stored Closes PC ADJUST MENU. Quit Other icons operates as follows. 3 To store adjustment parameters, move a red frame pointer to Stored icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store to and then press SELECT button. Reset all adjust parameters on adjustment dialog box to previous figure. Mode free This Mode has parameters being stored. Vacant Mode Shows values of “Fine sync,” “Horizontal,” “Vertical,” “Display area H,” and “Display area V.” Stored icon Mode free icon Close the dialog box. To store the adjustment data. To clear the adjustment data. To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. Move a red arrow pointer to the Mode that you want to clear and then press SELECT button.

Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and less than 180 MHz of Dot Clock. NOTE : Specifications are subject to change without notice. ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz) VGA 1 640 x 480 31.47 59.88 VGA 2 720 x 400 31.47 70.09 VGA 3 640 x 400 31.47 70.09 VGA 4 640 x 480 37.86 74.38 VGA 5 640 x 480 37.86 72.81 VGA 6 640 x 480 37.50 75.00 MAC LC13 640 x 480 34.97 66.60 MAC 13 640 x 480 35.00 66.67 MAC 16 832 x 624 49.72 74.55 MAC 19 1024 x 768 60.24 75.08 MAC 21 1152 x 870 68.68 75.06 MAC 1280 x 960 75.00 75.08 MAC 1280 x 1024 80.00 75.08 SVGA 1 800 x 600 35.156 56.25 SVGA 2 800 x 600 37.88 60.32 SVGA 3 800 x 600 46.875 75.00 SVGA 4 800 x 600 53.674 85.06 SVGA 5 800 x 600 48.08 72.19 SVGA 6 800 x 600 37.90 61.03 SVGA 7 800 x 600 34.50 55.38 SVGA 8 800 x 600 38.00 60.51 SVGA 9 800 x 600 38.60 60.31 SVGA 11 800 x 600 38.00 60.51 ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz) XGA 10 1024 x 768 XGA 11 1024 x 768 XGA 12 1024 x 768 XGA 13 1024 x 768 62.04 77.07 XGA 14 1024 x 768 61.00 75.70 XGA15 1024 x 768 35.522 86.96 (Interlace) 46.90 58.20 XGA 8 1024 x 768 47.00 58.30 XGA 9 1024 x 768 58.03 72.0 SXGA 1 1152 x 864 SXGA 2 1280 x 1024 63.48 79.35 SXGA 3 1280 x 1024 36.00 87.17 (Interlace) SXGA 4 1280 x 1024 64.20 70.40 SXGA 5 1280 x 1024 62.50 58.60 SXGA 6 1280 x 1024 63.90 60.00 SXGA 7 1280 x 1024 63.34 59.98 SXGA 8 1280 x 1024 63.74 60.01 SXGA 11 1152 x 900 71.69 67.19 SXGA 12 1152 x 900 81.13 76.107 SXGA 13 1280 x 1024 63.98 60.02 SXGA 14 1280 x 1024 61.20 65.20 71.40 75.60 50.00 86.00 (Interlace) HDTV720p –––––––– 50.00 94.00 (Interlace) 45.00 60.00 XGA 1 1024 x 768 XGA 2 1024 x 768 XGA 3 1024 x 768 XGA 4 1024 x 768 48.36 60.00 68.677 84.997 XGA 6 1024 x 768 60.023 75.03 XGA 7 1024 x 768 56.47 70.07 48.50 60.02 44.00 54.58 SXGA 9 1280 x 1024 SXGA 10 1280 x 960 79.976 75.025 60.00 60.00 SXGA 15 1280 x 1024 SXGA 16 1280 x 1024 SXGA 17 1152 x 900 SXGA 18 1280 x 1024 63.37 60.01 76.97 72.00 61.85 66.00 46.43 86.70 (Interlace) SXGA 19 1280 x 1024 63.79 60.18 XGA 5 1024 x 768 60.31 74.92 VGA 7 640 x 480 43.269 85.00 RGB –––––––– 15.734 60 (Interlace) RGB –––––––– 15.625 50 (Interlace) HDTV1080i –––––––– 33.75 60.00 (Interlace) HDTV1035i –––––––– 33.75 60.00 (Interlace) SVGA 10 800 x 600 32.70 51.09 SXGA 20 1280 x 1024 91.146 85.024

IMAGE LEVEL SELECT (MENU) Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. 1 2 Press POINT DOWN button to move a red frame pointer to the level that you want to set and then press SELECT button. Move the red frame icon to the level and press SELECT button. The level being selected. IMAGE SELECT MENU Normal picture level preset on this projector. Standard Picture level adjusted for the picture with fine tone. Real User preset picture adjustment in IMAGE ADJUST Menu (P29). IMAGE 1~4 IMAGE SELECT Menu icon IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on the Remote Control Unit. IMAGE button Standard Real Image 1 Image 2 Image 3 Image 4 Normal picture level preset on this projector. This normal picture level can also be selected by pressing NORMAL button. Picture level adjusted for the picture with fine tone. User preset picture adjustment in IMAGE ADJUST Menu (P29). Standard Real IMAGE 1~4

to adjust value. Reset all adjustment to previous figure. Reset Stored Closes IMAGE MENU. Quit Other icons operates as follows. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE ADJUST Menu icon. 1 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust. and then press SELECT button. The level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s). Move a red frame pointer to the item to be selected and then press SELECT button. IMAGE ADJUST MENU IMAGE LEVEL ADJUSTMENT Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.) Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.) Contrast Brightness Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.) Gamma 3 To store manually preset image, move a red frame pointer to STORE icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to the Image 1 to 4 where you want to set and then press SELECT button. Image Level Menu Move a red frame pointer to any of Image 1 to 4 where you want to set and then press SELECT button. Stored icon Press SELECT button at this icon to store the adjustment. IMAGE ADJUST Menu icon Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.) White balance (Red) Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.) White balance (Green) Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.) White balance (Blue) Selected Image level

This projector has a picture screen resize function, which enables you to display the desirable image size. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon. Adjusts image size or pans image. In “Digital Zoom” mode, the ON- SCREEN MENU disappears and the magnifying glass icon and the message “D. Zoom” is displayed. This projector also enters Digital Zoom mode by pressing the D.ZOOM L/M button on Remote Control Unit. 1 Refer to the following for operation. Expand function To expand the image size, press the D.ZOOM L button or the SELECT button. The image is magnified by degrees. Compress function To compress the image size, press the D.ZOOM M button. The size of image is reduced by degrees. Panning function To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is larger than the screen size. To return to screen size previously set, press NORMAL button. To cancel Digital Zoom mode, press any button except D.ZOOM L/M, SELECT, POINT, NORMAL or AUTO PC ADJ. button. Provides image in its original size. When the original image size is larger than screen size (1366 x 768), this projector enters Digital Zoom mode automatically. Image size can be set to Normal by pressing NORMAL button. Move the red frame to the function and press SELECT button. Press POINT DOWN button and move a red frame pointer to the function that you want to select and then press SELECT button. 2 True Digital Zoom NOTE G This SCREEN Menu cannot be operated when “HDTV720p,” “HDTV1035i” or “HDTV1080i” is selected on SYSTEM Menu (P23, 24). G True and Digital Zoom cannot be selected when “RGB” is selected on SYSTEM Menu (P23, 24). G This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting projector. G The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode. G Panning function may not operate properly if the computer system prepared on PC ADJUST Menu is used. Provides image to fit the vertical size of the screen. Normal Provides image to fit the horizontal size of the screen. Full SCREEN MENU SCREEN Menu icon

MENU OPERATION DIRECT OPERATION Choose either Input 2 or Input 3 by pressing INPUT button on the Top Control or on the Remote Control Unit. If projector cannot reproduce proper video source, select correct input source through MENU OPERATION (see below). Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon. Press POINT DOWN button to move a red arrow pointer to either Input 2 or Input 3 that you want to choose and then press SELECT button. Source Select Menu appear. 1 2 Move the arrow to the Input source and press SELECT button. INPUT 2 Move the arrow to the source and press SELECT button. Source Select Menu (Input 2 / 3) Move the pointer to the source that you want to select and then press SELECT button. 3 INPUT MENU INPUT button Input 1 Input 2 Input 3 INPUT 3

AV SYSTEM MENU (COMPONENT VIDEO) VIDEO MODE SELECTING VIDEO SYSTEM Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SYSTEM Menu icon. Press POINT DOWN button to move a red arrow pointer to the system that you want to select and then press SELECT button. 1 2 If projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N. Move the pointer to the system and press SELECT button. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N Projector automatically detects incoming Video signal, and adjusts itself to optimize its performance. If projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i, 480p, 575p, 720p, 1035i and 1080i. Auto COMPONENT VIDEO SIGNAL FORMAT VIDEO JACK, Y/C JACKS OR S-VIDEO JACK Y, Pb/Cb, Pr/Cr JACKS Projector automatically detects incoming Video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. Auto SYSTEM Menu icon This box indicates the system being selected. Move the pointer to the system and press SELECT button. SYSTEM Menu icon This box indicates the system being selected.

IMAGE LEVEL SELECT (MENU) Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. 1 2 Press POINT DOWN button to move a red frame pointer to the level that you want to set and then press SELECT button. Move the red frame pointer to the level and press SELECT button. The level being selected. IMAGE SELECT MENU Normal picture level preset on this projector. Standard Picture level adjusted for the picture with fine tone. Cinema User preset picture adjustment in IMAGE ADJUST Menu (P34). IMAGE 1~4 IMAGE SELECT Menu icon IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Cinema, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on the Remote Control Unit. Normal picture level preset on this projector. This normal picture level can also be selected by pressing NORMAL button. Standard Picture level adjusted for the picture with fine tone. Cinema User preset picture adjustment in IMAGE ADJUST Menu (P34). IMAGE 1~4 IMAGE button Standard Cinema Image 1 Image 2 Image 3 Image 4

to adjust value. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to IMAGE ADJUST Menu icon. 1 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button. The level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s). Move a red frame pointer to the item to be selected and then press SELECT button. IMAGE ADJUST MENU IMAGE LEVEL ADJUSTMENT Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.) Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.) Contrast Brightness Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.) Gamma Press SELECT button at this icon to display other items. IMAGE ADJUST Menu icon Press POINT LEFT/RIGHT buttons to adjust value. Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.) Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.) Color Tint Press POINT LEFT button to soften the image, and POINT RIGHT button to sharpen the image. (From 0 to 31.) Sharpness Set “On” to reduce noise (rough parts) of the image. Noise reduction Set “On” to provide progressive scan mode. Progressive Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.) White balance (Red) Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.) White balance (Green) Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.) White balance (Blue) NOTE : Tint cannot be adjusted when the video system is PAL, SECAM, PAL-M or PAL-N. Noise reduction cannot be selected when the input signal is from Y, Pb/Cb, Pr/Cr jacks. Progressive cannot be selected when “480p,” “575p” or “720p” is selected on SYSTEM Menu (P32). Press SELECT button at this icon to store the value.

This projector has a picture screen resize function, which enables you to display the desirable image size. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon. Press POINT DOWN button and move a red frame pointer to the function that you want to select and then press SELECT button. 1 2 Provides image to fit width of screen by expanding image width uniformly. This function can be used for providing a squeezed video signal at wide video aspect ratio of 16 : 9. When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select Full on this SCREEN Menu to provide better quality. Full NOTE : SCREEN Menu cannot be operated when “720p,” “1035i,” “1080i-50” or “1080i-60” is selected on SYSTEM Menu (P32). Move the red frame to the function and press SELECT button. SCREEN MENU SCREEN Menu icon Provides image to fit screen size (16 : 9 aspect ratio) by expanding image width and height uniformly. This function can be used for providing a letter box mode picture (4 : 3 aspect picture with black bar on top and bottom edges) at wide video aspect of 16 : 9. Zoom Provides image at the normal video aspect ratio of 4 : 3. Normal Provides image to fit width of screen by expanding both sides of image. This function is suitable to provide a normal video signal (4 : 3 aspect ratio) at wide video aspect ratio of 16 : 9. Wide zoom Reset all adjustment to previous figure. Reset Stored Closes IMAGE MENU. Quit Other icons operates as follows. 3 To store the adjustment data, move a red frame pointer to Stored icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to the Image Level 1 to 4 and then press SELECT button. Image Level Menu Move a red frame pointer to the image icon to be set and then press SELECT button. Stored icon

reversed. This function is used to project the image from a ceiling mounted projector. Rear When this function is “On,” picture is left / right reversed. This function is used to project the image to a rear projection screen. Ceiling function Rear function Keystone When the image is distorted vertically, select Keystone. ON- SCREEN Menu disappears and the message “Keystone” is displayed. Correct the Keystone distortion by pressing the POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page 21. SETTING MENU Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red-frame pointer to SETTING icon. 1 2 Language Language used in ON-SCREEN MENU is selectable from among English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish and Japanese. Display This function decides whether to display the On-Screen Displays. On ··· shows all the On-Screen Displays. Off ···· sets the On-Screen Displays disappeared except; G ON SCREEN MENU G “Power off?” message Set the red frame pointer to the item and press SELECT button. Press POINT DOWN button to move a red-frame pointer to the item that you want to set and then press SELECT button. Setting dialog box appears. Blue back When this function is “On,” this projector will produce a blue image instead of the video noise on the screen when the input source is unplugged or turned off. Logo When this function is “On,” projector displays logo when starting up. When selecting Language, Language Menu appears. Move the pointer to the item and then press POINT LEFT/RIGHT button(s). SETTING MENU SETTING Menu icon

interruption and projector is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.) Power Management function operates to turn Projection Lamp off when the input signal is interrupted and projector is not operated over 5 minutes. This function operates as follows; 1. When the signal is interrupted, “No signal” and the counting down display appears (for 5 minutes). 2. When Projection Lamp turned off, READY Indicator turns off. Cooling Fans operate and Projection Lamp is turned off for 90 seconds. (During this "Cooling Down" period, projector cannot be turned on.) 3. When Projection Lamp has cooled down, READY Indicator flashes and Projection Lamp can be turned on again (Power Management mode). In this Power Management mode, Projection Lamp is automatically turned on when the input signal connected or projector is operated with any button on the Top Control or on the Remote Control Unit. Power management This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 39 for operation. Lamp counter reset SETTING Remote control This projector has two different remote control codes; the factory-set normal code (Code 1) and the secondary code (Code 2). This switching function prevents the remote control operation mixture (jam) when operating several projectors or video equipment together. When operating projector in “Code 2,” both projector and Remote Control must be switched to “Code 2.” To change the code of Projector; Set the Remote control in the SETTING MENU to “Code 2.” To change the code of the Remote Control; Press both MENU and NORMAL buttons on the Remote Control Unit together for over 10 seconds. After changing the code, make sure the Remote Control operates properly. To return to the normal code (Code 1), operate both projector and Remote Control in the ways above again. NOTE : When batteries of the Remote Control Unit is replaced, the remote transmit code automatically returns to the normal code (Code 1). On start When this function is “On,” projector is automatically turned on just by switching MAIN ON / OFF SWITCH on. Note ; Be sure to turn projector off properly (refer to the section “TURNING OFF THE PROJECTOR” on page 20.). If projector is turned off in the wrong steps, On Start function does not operate properly. Time left until Lamp off. Move the pointer to the item and then press POINT LEFT/RIGHT button(s). Move the pointer to Lamp counter reset and then press SELECT button. The message “Lamp replace counter reset?” is displayed.

WARNING TEMP. Indicator flashes red when internal temperature of projector exceeds normal temperature. The Indicator stops flashing when temperature of projector returns to normal. When WARNING TEMP. Indicator continues to flash, check the items listed below. Ventilation slots of projector may be blocked. In such an event, reposition the appliance so that Ventilation slots are not obstructed. AIR FILTER CARE AND CLEANING Air Filters may be clogged with dust particles. Clean Air Filters by following the section AIR FILTER CARE AND CLEANING below. 1 2 If WARNING TEMP. Indicator remains on after performing the above checks, Cooling Fans or Internal Circuits may be malfunctioning. Contact a service personnel from an authorized dealer or service station. 3 Turn the power off, and disconnect the AC Power Cord from an AC outlet. Turn projector upside down and remove Air Filter Cover by pressing four latches sideways and pulling up. Remove three Air Filters by pulling up the latches. 1 2 Removable Air Filter prevents dust from accumulating on the surface of Projection Lens and the Projection Mirror. Should Air Filter become clogged with dust particles, it will reduce Cooling Fans' effectiveness and may result in internal heat build up and adversely affect the life of projector. Clean Air Filter following the steps below: Clean Air Filters with brush or wash out the dust and particles. Be sure to dry them out. 3 Replace Air Filters and Air Filter Cover properly. Make sure that they are fully set. 4 CAUTION Do not operate projector with Air Filters removed. Dust may accumulate on the LCD Panel and the Mirror degrading picture quality. Do not put small parts into Air Intake Vents. It may result in malfunction of projector. RECOMMENDATION We recommend avoiding dusty/smoky environments when operating projector. Usage in these environments may cause poor image quality. When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel, Projection Lens, or optical elements inside it. This condition may degrade the quality of the projected image. When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning. Air Filter Cover Press the latches sideways and pull up. Air Filters Remove three Air Filters by pulling up the latches. CLEANING THE PROJECTION LENS Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. When projector is not in use, replace the lens cover. 1 3 Lightly wipe the cleaning cloth over the lens. 2 Follow these steps to clean the projection lens:

image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required. Turn off projector and disconnect AC plug. Allow projector to cool for at least 45 minutes. Remove 2 screws and pull out Lamp Assembly by grasping Handle. 1 3 LAMP REPLACE COUNTER Replace Lamp Assembly with a new one and tighten 2 screws. Make sure that Lamp Assembly is set properly. Replace Lamp Cover and tighten a screw. 4 Remove a screw with a screwdriver and remove Lamp Cover. 2 CAUTION G For continued safety, replace with a lamp assembly of the same type. G Allow projector to cool for at least 45 minutes before you open the lamp cover. The inside of projector can become very hot. G Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury. Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE Indicator stops lighting. Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon (refer to page 36, 37). 1 Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press SELECT button. The message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SELECT button. 2 Do not reset Lamp Replace Counter except after Projection Lamp is replaced. Connect AC Power Cord to projector and turn on projector. 6 Follow these steps to replace the lamp assembly. Reset Lamp Replace Counter (refer to the section “Lamp Replace Counter” below). Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter. 3 5 LAMP ASSEMBLY HANDLE LAMP COVER NOTE : Do not reset Lamp Replace Counter when Projection Lamp is not replaced. ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following information to the dealer. G Model No. of your projector : PLV-60 G Replacement Lamp Type No. : POA-LMP28 (Service Parts No. 610 285 4824)

1. Make sure you have connected projector to your equipment as described in the section "CONNECTING THE PROJECTOR" on pages 11 ~ 13. 2. Check cable connection. Verify that all computer, video and power cords are properly connected. 3. Verify that all power is switched on. 4. If projector still does not produce an image, re-start the computer. 5. If the image sill does not appear, unplug projector from the computer and check the computer monitor's display. The problem may be with your graphics controller rather than with projector. (When you reconnect projector, remember to turn the computer and monitor off before you power up projector. Power the equipment back on in order of : projector and computer.) 6. If the problem still exists, check the following chart. No power. G Plug projector into the AC outlet. G Be sure READY Indicator light is On. G Wait 90 seconds after projector is turned OFF before turning projector back on. NOTE : After pressing the power ON-OFF switch to OFF, make sure projector works as follows: 1. The LAMP Indicator will light and the READY Indicator will turn off. 2. After 90 seconds, the READY Indicator will light green again and projector may be turned on by pressing the power ON-OFF button. G Check WARNING TEMP. Indicator. If this indicator flashes red, projector cannot be turned on. (See "TURNING ON/OFF THE PROJECTOR" section on page 20.) G Check the Projection Lamp. (Refer to page 39.) Image is out of focus. G Adjust the focus G Make sure the projection screen is at least 4.43’ (1.35 m) from projector. G Check the projection lens to see if it needs cleaning. NOTE : Moving projector from a cool temperature location to a warm temperature location may result in moisture condensation on the lens. In such an event, leave projector OFF and wait until condensation disappears. Picture is Left/Right reversed. G Check Ceiling / Rear feature. (See “SETTING” section on page 36.) Problem: Try these Solutions Picture is Top/Bottom reversed. G Check Ceiling feature. (See “SETTING” section on page 36.) Some displays are not seen during the Operation. G Check Display feature. (See “SETTING” section on page 36.) No image. G Check the connection between the computer or video equipment and projector. G When turning projector on, it takes about 30 seconds to display the image. G Check the system that you select is corresponding with the computer or the video equipment. G Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C). No sound. G Check audio cable connection from audio input source. G Adjust the audio source. G Press VOLUME (+) button. G Press MUTE button.

Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards. APPENDIX WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased projector or the service center. Give the model number and explain the difficulty. We will advise you how to obtain service. Remote Control Unit does not work. G Check the batteries. G Make sure nothing is between the Remote Receiver and the Remote Control Unit. G Make sure you are not too far from projector when using the Remote Control Unit. Maximum operating range is 16.4’ (5m). G Make sure the code of the Remote Control is set to conform to projector. (See “SETTING” section on page 36, 37.) Problem: Try these Solution

TECHNICAL SPECIFICATIONS Multi-media Projector 20.3 lbs (9.2 kg) 12.44" x 6.46" x 18.9" (316mm x 164mm x 480mm) 1366 x 768 dots 3,147,264 (1366 x 768 x 3 panels) PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz Adjustable from 31” to 400” 800 TV lines 2 speakers, 1.57" x 2.76" (40mm x 70mm) 41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C) 14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C) Owner’s Manual AC Power Cord Wired/Wireless Remote Control Transmitter and Batteries Video Cable (RCA x 1) Audio Cable (RCA x 2) S-Video Cable Remote Control Cable Dust Cover Lens Cover Projector Type Net Weight Dimensions (W x H x D) Panel Resolution Number of Pixels Color System Scanning Frequency Projection Image size (Diagonal) Horizontal Resolution Built-in Speakers Operating Temperature Storage Temperature Accessories LCD Panel System G The specifications are subject to change without notice. F 1.8 ~ 2.1 lens with f 48.4 mm ~ 62.8 mm with motor zoom, focus and shift 4.43’ ~ 45.9’ (1.35 m ~ 14.0 m) 250 W Projection Lens Throw Distance Projection Lamp RCA Type Jacks (R and L(mono)) x 3 Audio Input Jacks (Input 1/2/3) INPUT 1 : HDB 15 pin Type Terminal INPUT 2 : BNC Type Jacks (Video/Y, C/Pb(Cb), Pr(Cr)) / (G, B, R, H, V) Mini DIN 4 pin Type Jack (S-Video) INPUT 3 : RCA Type Jacks (Video/Y, Pb(Cb), Pr(Cr)) 2.0 W RMS (stereo) Computer / AV Input Jacks Internal Audio Amp 0˚ to 9.0˚ Feet Adjustment Power Source : AA, UM3 or R06 Type x 2 Operating Range : 16.4’ (5m) / ±30˚ Dimensions : 1.8” x 0.75” x 6.7” (45mm x 19mm x 170mm) Net Weight : 0.20 lbs (92 g) (including batteries) Remote Control Transmitter 480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60 High Definition TV Signal AC 100 ~ 120 V (4.4 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada) AC 200 ~ 240 V (2.2 A Max. Ampere), 50 / 60 Hz (Continental Europe and The U.K.) Voltage and Power Consumption RCA Type Jacks (R and L) Audio Output Jacks 35 mm Mini Jack (8 Ω2 W / stereo) External Speaker Jack HDB 9 pin Type Terminal Serial Port Terminal R/C Jack Mini Jack

RGB TERMINAL Terminal : HDB15-PIN Connect the display output terminal of computer to this terminal with VGA Cable (not supplied). When connecting the Macintosh computer, the MAC Adapter (not supplied) is required. 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 Red Input Ground (Horiz.sync.) Green Input Sense 2 Blue Input Ground (Red) Ground (Green) Ground (Blue) 1 5 2 4 3 6 7 8 No Connect Horiz. sync. Ground (Vert.sync.) Sense 1 Sense 0 Vert. sync. Reserved 9 13 10 12 11 14 15 Pin Configuration SERIAL TERMINAL Terminal : HDB9-PIN Connect the serial port of computer to this terminal with Serial Cable (not supplied). 3 5 4 2 1 7 9 8 6 No Connect Ground R x D No Connect T x D 1 5 2 4 3 No Connect RTS No Connect CTS 6 7 9 8 Pin Configuration MAC ADAPTER (NOT SUPPLIED) Set Slide Switches as shown in the table below depending on RESOLUTION MODE that you want to use before you turn-on projector and computer. ON 1 DIP ON OFF 2 3 4 5 6 13” MODE (640 x 480) 16” MODE (832 x 624) 19” MODE (1024 x 768) 21” MODE (1152 x 870) ON OFF OFF ON ON ON ON ON OFF OFF ON ON OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF 1 2 3 4 5 6 Slide Switches (1 ~ 6)