Scag Power Equipment SWZ Operator's Manual

been completed, the neutral latch is engaged and that the speed shift lever is in neutral. 1. Place the speed adjustment bearing lever where the bearing just contacts the speed adjustment cam. (See figure below). TRACKING STRAIGHT ADJUSTMENT -NOTE- Before making this adjustment be sure that the tire pressure has been checked and that it is correct. (See page 9) -NOTE- This adjustment will allow the machine to travel in a straight line at the normal oper- ating speed. ADJUSTMENTS (cont'd) Drive Position Neutral Position Steering Control ...

Tire pressures not equal Check and adjust tire pressure Width of Cutting Path Wheels uneven Check and adjust tire pressure Deck mounted incorrectly See your authorized SCAG dealer Uneven Cut on Flat Lift worn off of blade Replace blade Ground - Wavy High-Low Blade upside down Mount with cutting edge toward Appearance, ground Scalloped Cut, or Rough Contour Deck plugged,grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SCAG dealer Ben ...

8 Hours (Daily) Break-In (1st 10 Hours) 40 Hours (Weekly) 200 Hours (Monthly) X X X X X X X X X X X 100 Hours (Biweekly) PROCEDURE Check all hardware for proper tightness Change engine oil and filter at 5 hours Check hydrostatic oil filter at 20 hours Check belts for proper adjustment Check engine oil Clean blower screen Remove debris from under belt cover Sharpen cutter blades Grease spindle bearings * Clean air filter Check battery acid level Check tire pressure Grease caster wheel bearings Grease caster wheel pivots Grease idler arm pivots Change engine oil and ...

been completed, the neutral latch is engaged and that the speed shift lever is in neutral. 1. Place the speed adjustment bearing lever where the bearing just contacts the speed adjustment cam. (See figure below). TRACKING STRAIGHT ADJUSTMENT -NOTE- Before making this adjustment be sure that the tire pressure has been checked and that it is correct. (See page 9) -NOTE- This adjustment will allow the machine to travel in a straight line at the normal oper- ating speed. ADJUSTMENTS (cont'd) Drive Position Neutral Position Steering Control ...

HYDRAULIC ASSEMBLY 1 48535 Cap, Oil Reservoir x x x x x x x 2 46618 Oil Reservoir x x x 2 46619 Oil Reservior x x x x x x 3 48484-01 Elbow, 90 deg. Female 1/4 NPT to 1/4 JIC Male x x x x x x x 4 43853-02 Coupling, 7/16-20 SAE Flare Swivel to 1/4" Hose Push On x x x x x x x 5 48482 Hose, 1/4" ID - 12" Long (Order By The Inch) x x x x x x x 6 48350-04 Elbow, 90 deg. 7/16-20 JIC to 9/16-18 "O" Ring x x x x x x x 7 48603-06 O-Ring x x x x x x x 8 48551 Pump, Sunstrand BDP-10L117 x x x x x x x 9 04003-11 Bolt, Carriage, 3/8-1 ...

x x 1 46857 Upper Handle Wlmt. W/Decals x x x x 2 42675 Quadrant, Speed Control x x x x 3 04062-02 Hairpin, .094 x 1.19 x x x x 4 45282 Lever, Speed Adjustment x x x x 5 43086 Bushing, Speed Adjustment Lever x x x x 6 04001-20 Hex Head Bolt, 3/8-16 x 1-1/2" x x x x 7 48493-01 Ball Plunger x x x x 8 48092 Knob, Speed Adjustment x x x x 9 04014-01 Capscrew, 1/4-20 x 3/4" FHHS x x x x 10 04021-08 Nut, 1/4-20 Elastic Stop x x x x 11 04021-10 Nut, 5/16-18 Elastic Stop x x x x 12 04010-01 Screw, #10-32 x 1/2" PW HD x x x x 13 481071 Throttle Control x x x 13A 4 ...

-Note- For best cut and discharge a minimum of three spacers should be between the blade and spindle. (see page 8) NEUTRAL ADJUSTMENT TIRE PRESSURES Caster Wheels 25 PSI DriveWheels 15 PSI NEUTRAL ADJUSTMENT -NOTE- This is the only adjustment to properly set neutral. 1. Move the mower to a secure area away from bystanders and preferably, facing a wall. Raise the drive wheels off the ground. Block caster wheels. CAUTION Do not try to adjust neutral with the speed control rods or the speed adjustment cam. 2. Remove the speed control spring ...