Scientific Atlanta ER1 Operation & User’s Manual

Power DHCT on or off VCR on or off TV on or off LED Sound Mutes sound Adjusts volume Channels Displays channel information Selects channels, up or down Enter channel numbers (also used to enter your personal identification number [PIN] for parental control) Views favorite channels Returns to last channel viewed VCR/VOD 1 25 26 22 20 2 6 8 9 19 1 2 3 4 5 6 7 25 27 24 23 22 21 20 26 27 Model ER1 Remote Control User’s Guide 5 4 6 8 0 7 9 L A S T TV POWER SELECT B 2 1 3 C VOL + – CH + – INFO GUIDE M U T E E X I T V C R C B L S E T T I N G S A + – P A G E V C R T V / V C R V O D B Y P A S S F A V This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener- ates, uses, and can radiate radio frequency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the use is encourage to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. Any changes or modifications not expressly approved by Scientific-Atlanta could void the user’s authority to operate this equipment. United States: Scientific-Atlanta, Inc. 4261 Communications Drive, P.O. Box 6850, Norcross, GA 30091-6850 Tel: 770.903.5000 TWX: 810.799.4912 Telex: 0542898 Europe: Scientific-Atlanta Western Europe Limited, Home Park Estate, Kings Langley, Herts WD4 8LZ, England Tel: +44.1.923.266133 Fax: +44.1.923.269018 Asia-Pacific: Scientific-Atlanta (HK), Ltd. Suite 56-57, 5/F New Henry House, 10 Ice House Street, Central, Hong Kong Tel: 852.2522.5059 Fax: 852.2522.5624 © 2000 Scientific-Atlanta, Inc. All rights reserved. Printed in USA January 2000 Part Number 716360 Rev D To Program for Volume Control You can program the remote control to control the volume and mute functions through the EXPLORER 2000 DHCT, or through your TV. The default is through the TV. 1. Point the remote control away from the EXPLORER 2000 DHCT, the TV, and the VCR. 2. Press and hold the CBL key and the SELECT key at the same time, until the LED on the remote control blinks twice. 3. Using the remote control keypad, enter 993. The LED on the remote blinks twice. 4. Press the TV key or the CBL key, depending on which device you want to control the volume. The LED on the remote control blinks twice to confirm a valid selection. 5. Point the remote toward the device on which you chose to control the volume, and adjust the volume to confirm operation. Record of Codes Record your setup codes in the following table. CBL VCR TV FCC Compliance Controlling Volume

VCR Setup Codes Admiral—107 Adventura—060 Aiko—106 Akai—044 Alaron—193 Ambassador—191 Anam—194 Anam National—069, 194 AOC—033, 044, 199 Audiovox—106, 194, 465 Baysonic—194 Belcor—033 Bell & Howell—030, 168 Bradford—194 Brocksonic—250, 477 Candle—066, 044, 070 Carnivale—044 Carver—068 Celebrity—014 Cineral—106, 465 Citizen—060, 044, 070, 074, 106 Concerto—070 Brand—Codes Brand—Codes Harley Davidson—193 Harvard—194 Hitachi—070, 159 Infinity—068 Inteq—031 Janeil—060 JBL—068 JCB—014 JVC—067 KEC—194 Kenwood—044 Kloss—060 KTV—044, 194 LG—070 Logik—030 Luxman—070 LXI—061, 068, 168, 170, 192 Magnavox—044, 068, 193 Majessti—030 Marantz—044, 068 Matsushita—264 Megatron—159, 192 Proton—192 Pulsar—031 Quasar—179, 065, 264 Radio Shack—179, 044, 061, 070, 168, 192, 194 RCA—061, 104, 149, 065, 107 Realistic—179, 044, 070, 168, 192, 194 Runco—053 Sampo—044 Samsung—044, 070, 074, 192 Sansei—465 Sansui—477 Sanyo—168 Scotch—192 Scott—250, 192, 193, 194 Sears—061, 068, 070, 168, 170, 185, 192, 193 Semivox—194 Semp—170 Sharp—179, 107 Brand—Codes Brand—Co Brand—Codes Admiral—062 Adventura—014 Aiko—292 Aiwa—014, 051 Akai—055, 075, 120 American High—049 Asha—254 Audiovox—051 Beaumark—254 Bell & Howell—118 Brocksonic—016, 135, 198, 225 CCE—086, 292 Calix—051 Canon—049 Carver—095 Cineral—292 Citizen—051, 292 Colt—086 Craig—051, 061, 086, 254 Curtis Mathes—049, 055, 074, 176 Cybernex—254 KEC—051, 2 Kenwood—0 KLH—086 Kodak—049, LXI—051 Lloyd’s—014 Logik—086 Magnasonic— Magnavox—0 095 Magnin—254 Marantz—049 Marta—051 Matsushita— MEI—049 Memorex—0 049, 051 176, 254 MGA—057, 0 MGN Techno Introduction In addition to operating your digital home communications terminal (DHCT), you can program the ER1 Remote Control to operate your TV and VCR. To program the remote control, use the following proce- dure. Using Device Keys Remember to press the following appropri- ate device key to switch the remote control operation for the specific device: TV VCR CBL Programming for TV Operation The remote control for the DHCT controls the power, volume up and down, and mute functions. Make sure the power to your TV is turned on before you program the remote control. 1. Locate your TV brand and TV setup code in the table below. If your TV brand is not listed, see Searching the Code Library. 2. Point the remote control away from the DHCT, TV, and VCR. 3. On your remote control, press and hold the TV key and the SELECT key at the same time, until the LED on the remote blinks twice. 4. Using the remote control keypad, enter your TV’s 3-digit setup code. The LED on the remote control should blink twice. If not, try another setup code, if available. 5. Confirm by pointing the remote control toward the TV and test the POWER, VOLUME, and MUTE functions. Note: If you programmed the remote control to adjust the volume on your DHCT rather than the volume on the TV, test only the POWER function. If these functions do not operate from the remote control, enter the next TV setup code from the list and repeat this procedure from step 1. Programming for VCR Operation The remote control for the DHCT controls the VCR power, tape play, record, fast forward, rewind, stop, and TV/VCR functions. You can program the DHCT remote control to play video tapes. If you want the DHCT to manage the recording of events with your VCR, you must use the VCR Commander™ module. (See the VCR Commander™ User’s Guide for more infor- mation or ask your cable service provider.) Without this module, you must manually set up your VCR to record programs. Make sure the power to your VCR is turned on before you program the remote control. 1. Move the VCR/VOD slide switch on the remote control to the VCR position. 2. Locate your VCR brand and VCR setup code in the table below. If yourVCR brand is not listed, see Searching the Code Library. 3. Point the remote control away from the DHCT, the TV, and the VCR. Programming the Remote Control 4. On your remote control, press and hold the VCR key and the SELECT key at the same time, until the LED on the remote blinks twice. 5. Using the remote control keypad, enter your VCR’s 3-digit setup code. The LED on the remote control should blink twice. If not, try another setup code, if available. 6. Confirm by pointing the remote control toward the VCR and test the POWER, PLAY, and STOP functions. If these functions do not operate from the remote control, enter the next VCR setup code in the list and repeat this procedure from step 1. Searching the Code Library If none of the listed TV or VCR codes work, you can enter a code that searches the library of codes. The remote control automatically selects the proper code for your TV or VCR. Make sure the power to your TV or VCR is turned on before you program the remote control. 1. Point the remote control away from your TV or VCR, depending on which device you are programming.