QMS 3260 Quick Setup Manual

2 14" (36.4 cm) 3 8" (20 cm) 4 8" (20 cm) 5 18" (46 cm) 6 43" (108.4 cm) 1 42" (106 cm) 2 25" (63 cm) 3 8" (20 cm) 4 39" (100 cm) 5 18" (46 cm) 6 81" (206.9 cm)     1 Unpack the printer and remove the plastic covering. Contents of the box: • Printer • Power cord • Toner cartridge • Documenta- tion kit 2 With the help of another person, grasp the four bottom corners from the right and left sides, not from the front and back. Set the printer down on a sturdy, flat surface. 3 Remove all packing tape and lower the multi- purpose tray.    !   1 Open the side and front doors of the printer. 2 Unpack the toner cartridge and remove the protective paper sheet from the drum shutter. Holding the toner cartridge horizontal, shake it 5 or 6 times to evenly distribute the toner. 3 While holding the orange handle, gently push the toner cartridge all the way into the printer. 4 Gently pull out the toner cartridge sealing tape. Close the front and upper left doors of the printer. 1 2 3 4 5 6 1 2 3 4 5 6

Left door of the printer. 2 Locate the peel- off labels on each side of the fuser. 3 Peel off the label on the rear side of the fuser. 4 Use a coin to unscrew the rear side fuser plug. 5 Remove the rear side fuser plug. 6 Peel off the label on the front side of the fuser. 7 Use a coin to unscrew the front side fuser plug. 8 Remove the front side fuser plug.
   # 1 Open the paper tray by grasping the handle and pulling the tray toward you. 2 Gently lift the length guide and slide it to the right to the correct paper size. Press down the gray handle of the width guide and adjust to the correct paper size.

corners of the paper and place it in the tray. The paper should fit easily between the guides. Make sure the paper is not bent upward by the guides and does not exceed the maximum limit marks. 4 Adjust the side guide and the length guide to the edges of the paper stack. Insert the correct paper size label into the slot on the front of the tray, then push the tray back in until it latches. $    1 Connect your printer to the appropriate host communications cable. 2 Connect the power cable to the printer and then plug the printer into the appropriate power supply. Turn the printer on. !%    1 See the Getting Started manual for instructions on installing the QMS printer driver. Use the on-line help to configure the driver for printing. 2 See the Getting Started manual for complete instructions to configure the printer through the front panel menus. ! 
Operate the printer within a temperature range of 50°–90.5° F (10°–32.5° C) and a relative humidity range of 20%–80%.
Install the printer on a hard, level surface capable of supporting the 91 lb (41 kg) printer. The printer must be placed within 1.5° of level.
Allow enough space around the printer to allow adequate ventilation and easy servicing.
Use a properly grounded AC outlet with a line voltage of 100 V, 120 V, or 220-240 V, ±10%.
Maximum electrical current required during operation is 10 amps for a 100 V system, 8.3 amps for a 120 V system, and 4.5 amps for a 220-240 V system.
Recommended frequency is 50–60 Hz ±2 Hz for a 100 V system, 60 Hz ±2 Hz for a 120 V system, and 50 Hz ±2 Hz for a 220-240 V sys- tem.  WARNING! The printer weighs approximately 91 lbs (41 kg) without consumables. Do not attempt to lift the printer by yourself. ACHTUNG! Der Drucker hat ein Gewicht von ungefähr 41 kg. Bitte versuchen Sie niemals, den Drucker alleine anzuheben oder zu transportieren.
  



           Administration Idle Operator Installation* Copies 001-999 Duplex Off, On,

using the two thumbscrews. 2 Firmly attach the face-up tray to the connecting plate.  ' ( 1 Unpack the duplexer and make sure the multipurpose tray is down. Hook the duplexer into the slots of the feeder. 2 Firmly insert the stopper on the right side of the duplexer into the printer. 3 Secure the duplexer by hooking the safety wire of to the printer. 4 Plug the duplexer cable into the printer. Close the duplexer.  " & # ' ( )  1 Unpack the face-up tray and its parts: • Face-up tray • Face-up tray holder • Thumbscrews • Cutter/sup- porter 2 Holding the supplied cutter/ supporter sideways, insert it into the slot on the lower end of the filler panel. 3 Move the cutter/ supporter up and down to break the plastic connection. Repeat this step to break the other two connections. 4 Lift up the filler panel as shown to remove it from the printer.

supporter into the slots at the front end of the duplexer. It is used to support the face-up tray. 6 Insert the two thumbscrews into the face-up tray holder. 7 Attach the face- up tray holder to the printer and tighten the two thumbscrews. 8 Attach the face- up tray onto the holder.  *&!#"  *!" 1 Make sure the printer is unplugged from the power outlet and the communication cables. Unpack the HCIF and its parts, and remove any packing material or tape. 2 Lock the front roller on the HCIF. Make sure the connecting cable is fed through the cable notch on the rear of the HCIF. 3 With another person, lift the printer and lower it onto the HCIF, while noting the alignment of the covers of the printer and HCIF. 4 Pull the lower tray of the printer all the way out until it stops, then lift it up slightly to remove it. Remove the top tray of the HCIF, using the same technique. WARNING! The printer weighs approximately 91 lbs (41 kg) without consumables. Do not attempt to lift the printer by yourself. ACHTUNG! Der Drucker hat ein Gewicht von ungefähr 41 kg. Bitte versuchen Sie niemals, den Drucker alleine anzuheben oder zu transportieren. 5 Attach one mounting bracket to the left side of the printer/HCIF frame and secure it with a thumbscrew. 6 Attach the other mounting bracket to the right side of the printer/HCIF frame and secure it with a thumbscrew.

back into the printer and HCIF. 8 Plug the connecting cable from the HCIF into the printer at the rear side.  +,  "  1 Unpack the envelope feeder. 2 Remove the multipurpose tray from the printer. » Note: Firmly grasp the sides of the multipurpose tray and move it side-to-side to remove it. 3 Holding the envelope feeder horizontally, attach it to the printer. Make sure the two stubs on the feeder go securely into the slots on the printer. 4 Lift the envelope stopper and insert an envelope stack with the flap up and the long edge first. Slide the side guide in so it lightly touches the edge of the envelope stack.  *!# *! 1 With another person, lift the HCOS off of the pallet and stand the box to a vertical position. Open the box and unpack the HCOS and its components. 2 Included in the shipping box: • HCOS • Vertical trans- port • Locking bar • Staple car- tridge (not shown) • Support bracket (not shown) 3 Install the vertical transport onto the top of the printer. 4 Lock the rollers on the printer.    

bar under the printer and hook it into the center slot on the left side of the printer. 6 On the right side of the printer, push up the locking bar supporting unit to fit the tabs in the slots behind the printer cover. 7 Attach the align- ment bracket with the two thumbscrews on the right side of the printer. 8 Raise the horizontal transport, then flip down the two supporters so that it remains horizontal. 9 Move the HCOS close enough to the printer for cable connection. Make sure the HCOS and the printer align correctly. 10 Plug the power cable of the HCOS into the power outlet on the printer. 11 Extend the locking bar and insert the end into the opening on the bottom of the HCOS. 12 Gently push the HCOS towards the printer until they lock in place. Make sure the horizontal transport is positioned correctly on the top of the printer and its far end goes securely into the vertical transport. 13 Insert and tighten the locking screw to secure the HCOS to the printer. 14 Plug the interface cable of the HCOS into the output connector on the printer.