Fujitsu ETERNUS DX100 S3 Operation & User’s Manual

P2X0-1210-05ENZ0 FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETERNUS DX200F All Flash Array

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 3 Preface This manual describes how to use the Command Line Interface (CLI) to configure and manage the FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system, the FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system, or the FUJITSU Storage ETERNUS DX200 All Flash Array (hereinafter referred to as ETERNUS DX). This manual is written for standard-level users who are familiar with the basic functions of the ETERNUS DX. This manual is written for controller firmware version V10L20 or later. Some of the functions and operations herein may not be supported for firmware version V10L1x or earlier. Fifth Edition June 2014 Content and Structure This manual contains the following eight chapters and appendices: ●Chapter 1 Overview This chapter introduces the ETERNUS DX Command Line Interface (CLI). ●Chapter 2 Status Display This chapter explains the commands used for displaying the status details for the ETERNUS DX as a whole, as well as for various ETERNUS DX components. ●Chapter 3 Configuration Settings and Display This chapter explains the commands used for Thin Provisioning management, RAID group management, volume management, and host interface management, these being the basic settings for the ETERNUS DX. ●Chapter 4 Copy Function Settings and Display This chapter explains the commands used for Advanced Copy management. ●Chapter 5 System Settings and Display This chapter explains the commands used for user account management, network management (Redundant IP/SNMP etc.), date and time/NTP, system configuration (Box ID, Storage system name), power synchronization, and SSH/SSL security configuration. ●Chapter 6 Information Settings and Display This chapter explains the commands used to provide performance data and a variety of other information.

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 4 ●Chapter 7 NAS Function Setting and Display This chapter explains the commands related to NAS function management. ●Chapter 8 CLI Original Function This chapter explains the commands used by some original functions of the CLI environment. The appendices describe "Error Messages/Error Codes", "List of Supported Commands", "Basic Setting Exam- ples", "Status List", and "Default Value List". Latest Information The information in this manual is subject to change without notice for functionality expansion and improvement of the ETERNUS DX. The latest version of this manual and the latest information for the ETERNUS DX are released in the following web-site. Access the following address if needed. http://www.fujitsu.com/global/services/computing/storage/eternus/documentation/ Related Manuals The following manuals contain further relevant information on the ETERNUS DX: • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Overview • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Site Planning Guide • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Design Guide (Basic) • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Operation Guide (Basic) • FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Overview • FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide • FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Design Guide (Basic) • FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Configuration Guide (Basic) • FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic) • FUJITSU Storage ETERNUS DX200F All Flash Array Overview • FUJITSU Storage ETERNUS DX200F All Flash Array Site Planning Guide • FUJITSU Storage ETERNUS DX200F All Flash Array Design Guide (Basic) • FUJITSU Storage ETERNUS DX200F All Flash Array Configuration Guide (Basic) • FUJITSU Storage ETERNUS DX200F All Flash Array Operation Guide (Basic) • FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETER- NUS DX200F All Flash Array Message List • FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage system Configuration Guide (NAS) • FUJITSU Storage ETERNUS DX Configuration Guide (Web GUI) ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETERNUS DX200F All Flash Array

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 5 • ETERNUS Web GUI User's Guide (Operation) FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETERNUS DX200F All Flash Array • ETERNUS Web GUI User's Guide (Settings) FUJITSU Storage ETERNUS DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk storage systems, ETERNUS DX200F All Flash Array • FUJITSU Storage ETERNUS DX Disk storage systems Configuration Guide -Server Connection- (*1) *1: Download the necessary manuals to match the environment (such as the server OS and the Fibre Channel card type) from the specified Web site. Trademarks • Microsoft, Windows, and Windows Server are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Oracle and Java are registered trademarks of Oracle and/or its affiliates. • AIX is a trademark of IBM Corp. • Linux is a registered trademark of Linus Torvalds. • HP-UX is a trademark of Hewlett-Packard Company in the United States and other countries. • VMware, VMware logos, Virtual SMP, and VMotion are either registered trademarks or trademarks of VMware, Inc. in the U.S. and/or other countries. • VERITAS Volume Manager is a trademark of Symantec Corp. and its affiliated companies. • The company names, product names and service names mentioned in this document are registered trademarks or trademarks of their respective companies.

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 6 Additional Information ■ Naming conventions • Oracle Solaris might be described as Solaris, Solaris Operating System, or Solaris OS. • The following abbreviations are used for Microsoft® Windows Server®. ■ Typographic conventions • Italics are used to show variables such as values and characters that appear in command parameters and output examples. Official name Abbreviation Microsoft® Windows Server® 2008 R2 Datacenter Windows Server 2008 R2 Microsoft® Windows Server® 2008 R2 Enterprise Microsoft® Windows Server® 2008 R2 Standard Microsoft® Windows Server® 2008 R2 for Itanium-Based Systems Microsoft® Windows Server® 2008 R2 HPC Edition Microsoft® Windows Server® 2008 Datacenter Windows Server 2008 Microsoft® Windows Server® 2008 Enterprise Microsoft® Windows Server® 2008 Standard Microsoft® Windows Server® 2008 for Itanium-Based Systems Microsoft® Windows Server® 2008 HPC Edition Typeface Meaning Example [ ] Brackets indicate that the enclosed parameter is optional. [ parameter ] [ | ] A separator within brackets indicates that only one of the separated parameters can be specified. [ parameter | parameter ] { | } A separator within braces indicates that only one of the separated parameters must be specified. Note that some cases, two or more parameters can be specified by separating them with a comma. { parameter | parameter }

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 7 ■ ETERNUS DX naming conventions The following naming conventions are used in this manual for the ETERNUS DX models. ■ Symbol conventions The following symbols are used throughout this manual: ETERNUS DX models Naming conventions ETERNUS DX100 S3/DX200 S3 Disk storage system ETERNUS DX500 S3/DX600 S3 Disk storage system ETERNUS DX200F All Flash Array ETERNUS DX ETERNUS DX100 S3/DX200 S3 Disk storage system ETERNUS DX100 S3/DX200 S3 ETERNUS DX500 S3/DX600 S3 Disk storage system ETERNUS DX500 S3/DX600 S3 ETERNUS DX100 S3/DX200 S3 Disk storage system ETERNUS DX500 S3/DX600 S3 Disk storage system ETERNUS DX S3 series ETERNUS DX60 S2 Disk storage system ETERNUS DX80 S2/DX90 S2 Disk storage system ETERNUS DX410 S2/DX440 S2 Disk storage system ETERNUS DX8100 S2/DX8700 S2 Disk storage system ETERNUS DX S2 series ETERNUS DX200F All Flash Array ETERNUS DX200F This symbol indicates restrictions and cautions for setting up and operating the ETERNUS DX. This symbol indicates supplementary information about functions and methods that may be useful when setting up and operating the ETERNUS DX.

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 8 Table of Contents Chapter 1 Overview 21 1.1 Accessing CLI ..................................................................................................................... 21 1.2 The Command Syntax ....................................................................................................... 22 1.2.1 Command Format ..........................................................................................................................................22 1.2.2 Keywords and Parameters .............................................................................................................................22 1.2.3 Drive Enclosure Syntax ..................................................................................................................................22 1.2.4 Drive Syntax ..................................................................................................................................................23 1.2.5 Alias Name Syntax .........................................................................................................................................23 1.2.6 Thin Provisioning Pool Syntax ........................................................................................................................23 1.2.7 Flexible Tier Pool Syntax ................................................................................................................................24 1.2.8 Flexible Tier Sub Pool Syntax .........................................................................................................................25 1.2.9 RAID Group Syntax .........................................................................................................................................25 1.2.10 Volume Syntax ...............................................................................................................................................26 1.2.11 Host Syntax ...................................................................................................................................................27 1.2.12 LUN Group Syntax ..........................................................................................................................................28 1.2.13 Host Response Syntax ....................................................................................................................................28 1.2.14 Eco-mode Schedule Syntax ............................................................................................................................29 1.2.15 Host Interface Port Syntax .............................................................................................................................29 1.2.16 Port Group Syntax ..........................................................................................................................................30 1.2.17 Host Group Syntax .........................................................................................................................................30 1.3 Size of Drives and Logical Units ......................................................................................... 31 1.4 Command Auto-complete and History Recall .................................................................... 31 1.5 Command Editing Hotkeys ................................................................................................ 32 1.6 Viewing Command Help .................................................................................................... 33 1.7 Error Message Format ....................................................................................................... 34 1.8 Multiple Sessions .............................................................................................................. 34 1.9 Slave Controller Logins ...................................................................................................... 35 1.10 CLI User Authority ............................................................................................................. 35 1.11 Note for Specifying FTP Server ........................................................................................... 35 1.12 Command Descriptions ..................................................................................................... 36

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 9 Chapter 2 Status Display 37 2.1 Storage System Status ...................................................................................................... 37 show status ..............................................................................................................................................38 show enclosure-status ..............................................................................................................................39 show fru-ce ...............................................................................................................................................46 show fru-de ..............................................................................................................................................59 show disks ................................................................................................................................................63 show hardware-information .....................................................................................................................67 Chapter 3 Configuration Settings and Display 69 3.1 RAID Group Management ................................................................................................. 69 3.1.1 RAID Group ....................................................................................................................................................69 show raid-groups .....................................................................................................................................70 show raid-group-progress ........................................................................................................................73 create raid-group .....................................................................................................................................75 set raid-group ..........................................................................................................................................77 delete raid-group .....................................................................................................................................79 expand raid-group ...................................................................................................................................80 3.1.2 Hot Spares .....................................................................................................................................................82 set global-spare .......................................................................................................................................83 release global-spare .................................................................................................................................84 set dedicated-spare ..................................................................................................................................85 release dedicated-spare ...........................................................................................................................87 3.1.3 Eco-mode Management ................................................................................................................................88 show eco-mode ........................................................................................................................................89 set eco-mode ...........................................................................................................................................90 show eco-schedule ...................................................................................................................................91 create eco-schedule .................................................................................................................................93 set eco-schedule ......................................................................................................................................96 delete eco-schedule .................................................................................................................................99 show eco-raid-group ..............................................................................................................................100 set eco-raid-group ..................................................................................................................................102 release eco-raid-group ...........................................................................................................................104 3.2 Volume Management ..................................................................................................... 105 3.2.1 Volume ........................................................................................................................................................105 show volumes ........................................................................................................................................106 show volume-progress ...........................................................................................................................114 show volume-mapping ..........................................................................................................................117 create volume ........................................................................................................................................119 set volume .............................................................................................................................................125 delete volume ........................................................................................................................................127 delete all-volumes .................................................................................................................................128 format volume .......................................................................................................................................130

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 10 expand volume ......................................................................................................................................131 show migration ......................................................................................................................................133 start migration .......................................................................................................................................134 stop migration .......................................................................................................................................137 show balancing-thin-pro-volumes .........................................................................................................138 start balancing-thin-pro-volume ............................................................................................................140 stop balancing-thin-pro-volume ............................................................................................................141 start zero-reclamation ............................................................................................................................142 stop zero-reclamation ............................................................................................................................143 show volume-qos ...................................................................................................................................144 set volume-qos .......................................................................................................................................146 3.2.2 Flexible Tier Volumes ...................................................................................................................................148 create flexible-tier-volume .....................................................................................................................149 set flexible-tier-volume ..........................................................................................................................151 format flexible-tier-volume ....................................................................................................................153 expand flexible-tier-volume ...................................................................................................................154 delete flexible-tier-volume .....................................................................................................................155 delete all-flexible-tier-volumes ..............................................................................................................156 start flexible-tier-migration ...................................................................................................................157 3.2.3 ODX Buffer Volume ......................................................................................................................................159 show odx-mode .....................................................................................................................................160 set odx-mode .........................................................................................................................................161 create odx-buffer-volume .......................................................................................................................162 set odx-buffer-volume ............................................................................................................................165 delete odx-buffer-volume ......................................................................................................................167 3.2.4 Extreme Cache .............................................................................................................................................168 show extreme-cache ..............................................................................................................................169 set extreme-cache ..................................................................................................................................170 set volume-exc .......................................................................................................................................172 3.3 Thin Provisioning Pool Management ..............................................................................174 3.3.1 Thin Provisioning Pool .................................................................................................................................174 show thin-provisioning ..........................................................................................................................176 set thin-provisioning ..............................................................................................................................177 show thin-pro-pools ...............................................................................................................................179 show thin-pro-pool-progress ..................................................................................................................181 create thin-pro-pool ...............................................................................................................................183 set thin-pro-pool ....................................................................................................................................186 delete thin-pro-pool ...............................................................................................................................187 expand thin-pro-pool .............................................................................................................................188 format thin-pro-pool ..............................................................................................................................190 3.3.2 Thin Provisioning Pool Eco-mode Management ..........................................................................................191 show eco-thin-pro-pool ..........................................................................................................................193 set eco-thin-pro-pool .............................................................................................................................194 release eco-thin-pro-pool .......................................................................................................................196

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 11 3.4 Flexible Tier Management .............................................................................................. 197 3.4.1 Flexible Tier Pools ........................................................................................................................................197 show flexible-tier-mode .........................................................................................................................198 show flexible-tier-pools ..........................................................................................................................199 show flexible-tier-pool-progress ............................................................................................................202 delete flexible-tier-pool .........................................................................................................................205 show flexible-tier-sub-pools ...................................................................................................................206 set flexible-tier-sub-pool ........................................................................................................................209 3.4.2 FTRPE Migration ..........................................................................................................................................210 show ftrpe-migration .............................................................................................................................211 3.4.3 FTV Balancing ..............................................................................................................................................212 show balancing-flexible-tier-pools .........................................................................................................213 start balancing-flexible-tier-pool ...........................................................................................................216 stop balancing-flexible-tier-pool ............................................................................................................217 3.5 Host Interface Management ...........................................................................................218 3.5.1 Host Interface Port Parameters ....................................................................................................................221 show fc-parameters ................................................................................................................................222 set fc-parameters ...................................................................................................................................226 show sas-parameters .............................................................................................................................230 set sas-parameters .................................................................................................................................232 show iscsi-parameters ............................................................................................................................234 set iscsi-parameters ...............................................................................................................................239 show fcoe-parameters ............................................................................................................................250 set fcoe-parameters ...............................................................................................................................253 3.5.2 Host Identifiers (Host Alias) .........................................................................................................................256 show host-wwn-names ..........................................................................................................................257 create host-wwn-name ..........................................................................................................................258 set host-wwn-name ...............................................................................................................................260 delete host-wwn-name ..........................................................................................................................262 discover host-wwn-names ......................................................................................................................263 show host-sas-addresses ........................................................................................................................264 create host-sas-address ..........................................................................................................................265 set host-sas-address ...............................................................................................................................267 delete host-sas-address .........................................................................................................................269 discover host-sas-addresses ...................................................................................................................270 show host-iscsi-names ...........................................................................................................................271 create host-iscsi-name ...........................................................................................................................273 set host-iscsi-name ................................................................................................................................277 delete host-iscsi-name ...........................................................................................................................280 discover host-iscsi-names .......................................................................................................................281 3.5.3 Mapping (When LUN Groups are Used) .......................................................................................................283 show host-affinity ..................................................................................................................................284 set host-affinity ......................................................................................................................................290 copy host-affinity ...................................................................................................................................294 release host-affinity ...............................................................................................................................295

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 12 3.5.4 Mapping (When Host Affinity Mode is Not Used) ........................................................................................298 show mapping .......................................................................................................................................299 set mapping ...........................................................................................................................................302 copy mapping ........................................................................................................................................304 release mapping ....................................................................................................................................305 3.5.5 Host Groups .................................................................................................................................................307 show host-groups ...................................................................................................................................308 create host-group ...................................................................................................................................311 set host-group ........................................................................................................................................313 delete host-group ..................................................................................................................................315 3.5.6 Port Groups ..................................................................................................................................................316 show port-groups ...................................................................................................................................317 create port-group ...................................................................................................................................319 set port-group ........................................................................................................................................320 delete port-group ...................................................................................................................................322 3.5.7 LUN Groups ..................................................................................................................................................323 show lun-groups ....................................................................................................................................324 create lun-group ....................................................................................................................................326 set lun-group .........................................................................................................................................328 copy lun-group .......................................................................................................................................330 delete lun-group ....................................................................................................................................331 show host-path-state .............................................................................................................................333 set host-path-state .................................................................................................................................335 show host-lu-qos-performance ..............................................................................................................336 start host-lu-qos-performance ...............................................................................................................345 stop host-lu-qos-performance ................................................................................................................346 3.5.8 Host Response .............................................................................................................................................347 show host-response ...............................................................................................................................348 set host-response ...................................................................................................................................351 delete host-response ..............................................................................................................................356 3.5.9 Host Sense Conversion .................................................................................................................................357 show host-sense .....................................................................................................................................358 set host-sense ........................................................................................................................................360 delete host-sense ...................................................................................................................................362 3.5.10 Reset Group for Host Interface Port ..............................................................................................................363 show ca-reset-group ...............................................................................................................................364 set ca-reset-group ..................................................................................................................................365 3.5.11 Ping Command for iSCSI Hosts .....................................................................................................................366 test iscsi-ping .........................................................................................................................................367 3.5.12 Host LU QoS .................................................................................................................................................369 show qos-mode ......................................................................................................................................370 set qos-mode .........................................................................................................................................371 show lu-qos-groups ................................................................................................................................372 set lu-qos-group .....................................................................................................................................374 delete lu-qos-group ................................................................................................................................376 show host-lu-qos ....................................................................................................................................377

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 13 set host-lu-qos .......................................................................................................................................383 show qos-schedule .................................................................................................................................387 set qos-schedule ....................................................................................................................................388 delete all-qos-setting .............................................................................................................................391 Chapter 4 Copy Function Settings and Display 392 4.1 Advanced Copy Management .......................................................................................... 392 4.1.1 SnapOPC+ Outline ........................................................................................................................................393 4.1.2 Preparations for the Advanced Copy Function ..............................................................................................393 4.1.3 Copy Session Management ..........................................................................................................................397 show advanced-copy-license ..................................................................................................................399 set advanced-copy-license .....................................................................................................................401 delete advanced-copy-license ................................................................................................................402 show advanced-copy-policy ....................................................................................................................403 set advanced-copy-policy .......................................................................................................................404 show advanced-copy-parameters ...........................................................................................................405 set advanced-copy-parameters ..............................................................................................................406 show snap-data-volume .........................................................................................................................408 initialize snap-data-volume ...................................................................................................................410 show snap-data-pool .............................................................................................................................411 delete snap-data-pool-volume ...............................................................................................................413 show advanced-copy-sessions ................................................................................................................414 start advanced-copy ...............................................................................................................................420 stop advanced-copy ...............................................................................................................................421 4.1.4 Remote Equivalent Copy Management ........................................................................................................422 4.1.5 Summaries of REC Environment Settings through CLI ..................................................................................423 show host-port-mode .............................................................................................................................433 set host-port-mode ................................................................................................................................434 show rec-path ........................................................................................................................................436 import rec-path ......................................................................................................................................440 show backup-rec-path-information ........................................................................................................442 export backup-rec-path ..........................................................................................................................443 convert rec-path .....................................................................................................................................445 measure rec-round-trip-time ..................................................................................................................447 set rec-round-trip-time ...........................................................................................................................449 set rec-multiplicity .................................................................................................................................450 show rec-buffer ......................................................................................................................................452 set rec-buffer ..........................................................................................................................................453 delete rec-buffer ....................................................................................................................................457 show rec-disk-buffer ...............................................................................................................................458 create rec-disk-buffer .............................................................................................................................460 set rec-disk-buffer ..................................................................................................................................462 delete rec-disk-buffer .............................................................................................................................463 format rec-disk-buffer ............................................................................................................................464 release rec-disk-buffer ...........................................................................................................................465

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 14 Chapter 5 System Settings and Display 466 5.1 User Management .......................................................................................................... 467 5.1.1 Role .............................................................................................................................................................467 show role ...............................................................................................................................................468 create role ..............................................................................................................................................469 set role ...................................................................................................................................................471 delete role ..............................................................................................................................................473 show users .............................................................................................................................................474 create user .............................................................................................................................................475 set user ..................................................................................................................................................476 delete user .............................................................................................................................................477 show login-users ....................................................................................................................................478 set password ..........................................................................................................................................479 initialize all-users ...................................................................................................................................480 import ssh-public-key .............................................................................................................................481 delete ssh-public-key .............................................................................................................................483 5.1.2 RADIUS Server Settings ................................................................................................................................484 show radius ............................................................................................................................................485 set radius ...............................................................................................................................................487 5.2 Network Management ....................................................................................................491 5.2.1 Network Settings .........................................................................................................................................491 show network .........................................................................................................................................492 set network ............................................................................................................................................495 show firewall ..........................................................................................................................................502 set firewall .............................................................................................................................................504 5.2.2 SNMP ...........................................................................................................................................................508 show snmp .............................................................................................................................................509 set snmp ................................................................................................................................................510 show snmp-manager .............................................................................................................................512 create snmp-manager ............................................................................................................................513 set snmp-manager .................................................................................................................................514 delete snmp-manager ............................................................................................................................515 show snmp-view ....................................................................................................................................516 create snmp-view ...................................................................................................................................518 set snmp-view ........................................................................................................................................520 delete snmp-view ...................................................................................................................................522 show snmp-user .....................................................................................................................................523 create snmp-user ...................................................................................................................................525 set snmp-user ........................................................................................................................................527 delete snmp-user ...................................................................................................................................529 show community-profile ........................................................................................................................531 create community-profile .......................................................................................................................533 set community-profile ............................................................................................................................535 delete community-profile .......................................................................................................................537

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 15 show snmp-trap .....................................................................................................................................538 set snmp-trap .........................................................................................................................................539 delete snmp-trap ...................................................................................................................................541 test snmp-trap .......................................................................................................................................542 export enhanced-mib .............................................................................................................................543 5.2.3 E-mail Notification ......................................................................................................................................545 show email-notification .........................................................................................................................546 set email-notification .............................................................................................................................548 test email ...............................................................................................................................................554 5.2.4 Event Notification ........................................................................................................................................555 show event-notification .........................................................................................................................556 set event-notification .............................................................................................................................559 5.2.5 SMI-S ...........................................................................................................................................................569 show smi-s .............................................................................................................................................570 set smi-s .................................................................................................................................................571 5.2.6 SSH/SSL Security Configuration ....................................................................................................................572 create ssh-server-key .............................................................................................................................575 create ssl-certificate ...............................................................................................................................576 export ssl-certificate-request ..................................................................................................................578 import ssl-certificate ..............................................................................................................................582 5.2.7 AIS Connect Settings ....................................................................................................................................584 show ais-connect ....................................................................................................................................585 set ais-connect .......................................................................................................................................587 set ais-connect-remote-session ..............................................................................................................593 test ais-connect ......................................................................................................................................594 send ais-connect-log ..............................................................................................................................595 test ais-connect-event-notification ........................................................................................................596 import ais-ssl-certificate .........................................................................................................................597 5.3 System Settings .............................................................................................................. 599 5.3.1 Date, Time and NTP .....................................................................................................................................599 show date ..............................................................................................................................................600 set date ..................................................................................................................................................601 show ntp ................................................................................................................................................604 set ntp ....................................................................................................................................................606 5.3.2 ETERNUS DX Name ......................................................................................................................................608 show storage-system-name ...................................................................................................................609 set storage-system-name .......................................................................................................................610 5.3.3 Encryption Mode ..........................................................................................................................................611 show encryption .....................................................................................................................................612 set encryption ........................................................................................................................................613 5.3.4 Box ID ..........................................................................................................................................................614 show boxid .............................................................................................................................................615 set boxid ................................................................................................................................................616 5.3.5 Power Synchronization ................................................................................................................................617 show power-synchronization ..................................................................................................................618 set power-synchronization .....................................................................................................................620

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 16 5.3.6 Self-Encrypting Drive (SED) Authentication Settings ...................................................................................623 show sed-authentication ........................................................................................................................624 set sed-authentication ...........................................................................................................................625 5.3.7 Syslog Server Settings ..................................................................................................................................626 show syslog-notification .........................................................................................................................627 set syslog-notification ............................................................................................................................628 5.3.8 Audit Log Settings .......................................................................................................................................630 show audit .............................................................................................................................................631 set audit .................................................................................................................................................632 5.3.9 Key Management Server Linkage Function ..................................................................................................635 show sed-key-machine-name ................................................................................................................637 set sed-key-machine-name ....................................................................................................................638 show sed-key-servers .............................................................................................................................639 set sed-key-server ..................................................................................................................................640 import ssl-kmip-certificate .....................................................................................................................641 show sed-key-groups .............................................................................................................................643 create sed-key-group .............................................................................................................................645 set sed-key-group ..................................................................................................................................647 delete sed-key-group .............................................................................................................................649 change sed-key ......................................................................................................................................650 recover sed-key-group ............................................................................................................................651 5.3.10 Shutdown/Restart System ............................................................................................................................652 shutdown ...............................................................................................................................................653 Chapter 6 Information Settings and Display 654 6.1 Performance ................................................................................................................... 654 6.1.1 Performance Information ............................................................................................................................654 show performance ..................................................................................................................................655 start performance ...................................................................................................................................662 stop performance ...................................................................................................................................663 6.1.2 Performance Tuning Parameters .................................................................................................................664 show raid-tuning ....................................................................................................................................665 set raid-tuning .......................................................................................................................................666 show cache-parameters .........................................................................................................................668 set cache-parameters .............................................................................................................................669 6.2 Event Log Information ....................................................................................................672 show events ...........................................................................................................................................673 delete events .........................................................................................................................................675 6.3 Maintenance Information ...............................................................................................676 6.3.1 Remote Directory .........................................................................................................................................676 show remote-dir .....................................................................................................................................677 6.3.2 Controller Firmware .....................................................................................................................................679 show firmware-version ...........................................................................................................................680

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 17 6.3.3 Log ..............................................................................................................................................................681 export log ...............................................................................................................................................682 6.3.4 Panic Dump .................................................................................................................................................685 show panic-dump ...................................................................................................................................686 export panic-dump .................................................................................................................................687 6.3.5 Configuration Information ...........................................................................................................................689 show config-information ........................................................................................................................690 export config-information ......................................................................................................................691 6.3.6 Error Information .........................................................................................................................................693 show disk-error ......................................................................................................................................694 clear disk-error .......................................................................................................................................695 show port-error ......................................................................................................................................696 6.3.7 Bad Data Information in Volumes ................................................................................................................700 show bad-data-info ................................................................................................................................701 6.4 Utility ..............................................................................................................................703 6.4.1 Diagnosis Utilities ........................................................................................................................................703 show diagnosis .......................................................................................................................................704 6.4.2 LED ..............................................................................................................................................................710 show led .................................................................................................................................................711 set led ....................................................................................................................................................713 6.4.3 Other Notification ........................................................................................................................................714 show event-parameters .........................................................................................................................715 set event-parameters .............................................................................................................................716 6.4.4 Sub-system Parameters ...............................................................................................................................717 show subsystem-parameters ..................................................................................................................718 set subsystem-parameters .....................................................................................................................719 6.4.5 Reservations ................................................................................................................................................722 show reservation ....................................................................................................................................723 release reservation .................................................................................................................................725 6.4.6 Cache Utilities ..............................................................................................................................................726 show pinned-data ..................................................................................................................................727 6.4.7 Disk Patrol ...................................................................................................................................................728 show disk-patrol .....................................................................................................................................729 set disk-patrol ........................................................................................................................................730 Chapter 7 NAS Function Setting and Display 731 7.1 Shared Folders ................................................................................................................ 733 show nas-share ......................................................................................................................................734 create nas-share .....................................................................................................................................737 set nas-share ..........................................................................................................................................742 delete nas-share ....................................................................................................................................746 7.2 Network Interface ........................................................................................................... 748 show nas-interface .................................................................................................................................749 create nas-interface ...............................................................................................................................752

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 18 set nas-interface ....................................................................................................................................755 delete nas-interface ...............................................................................................................................759 7.3 Network Interface Bonding ............................................................................................. 760 show nas-bonding ..................................................................................................................................761 set nas-bonding .....................................................................................................................................762 delete nas-bonding ................................................................................................................................764 7.4 Network Interface Multipath Configuration .....................................................................766 show nas-multipath ...............................................................................................................................767 set nas-multipath ...................................................................................................................................768 delete nas-multipath .............................................................................................................................769 7.5 Network Settings ............................................................................................................770 show nas-port ........................................................................................................................................771 set nas-port ............................................................................................................................................773 show nas-dns .........................................................................................................................................775 set nas-dns .............................................................................................................................................776 show nas-route ......................................................................................................................................778 set nas-route ..........................................................................................................................................780 delete nas-route .....................................................................................................................................782 show nas-route6 ....................................................................................................................................784 set nas-route6 ........................................................................................................................................786 delete nas-route6 ...................................................................................................................................788 7.6 NAS Server Configuration ................................................................................................790 show nas-server .....................................................................................................................................791 set nas-server .........................................................................................................................................792 7.7 Authentication Settings .................................................................................................. 793 show nas-ad ...........................................................................................................................................794 set nas-ad ..............................................................................................................................................795 show nas-ldap ........................................................................................................................................797 set nas-ldap ...........................................................................................................................................798 7.8 Network Connection Testing ...........................................................................................800 test nas-ping ..........................................................................................................................................801 test nas-ping6 ........................................................................................................................................802 test nas-traceroute .................................................................................................................................803 test nas-traceroute6 ...............................................................................................................................804 7.9 File System Maintenance ................................................................................................805 show nas-df ............................................................................................................................................806 show nas-fsstat ......................................................................................................................................808 show nas-fsmntstat ................................................................................................................................810 7.10 NAS Function Restoration ...............................................................................................811 forced nas-fsmount ................................................................................................................................812 forced nas-fsunmount ............................................................................................................................813 forced nas-fsoffline ................................................................................................................................814

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 19 forced nas-fsonline .................................................................................................................................815 show nas-fsck .........................................................................................................................................816 start nas-fsck ..........................................................................................................................................817 forced nas-fslock ....................................................................................................................................818 recover nas-engine .................................................................................................................................819 forced online ..........................................................................................................................................820 Chapter 8 CLI Original Function 821 8.1 CLI Environment .............................................................................................................. 821 set clienv-force-unlock ...........................................................................................................................822 set clienv-idle-timeout ...........................................................................................................................823 logoff/logout/exit ...................................................................................................................................824 help ........................................................................................................................................................825 Appendix A Error Messages/Error Codes 827 A.1 Error Messages ................................................................................................................ 827 A.2 Error Codes....................................................................................................................... 881 A.2.1 Copy Session Error Codes ............................................................................................................................. 881 Appendix B List of Supported Commands 882 B.1 List of Supported Commands ...........................................................................................882 B.2 List of Supported Commands (Policies)............................................................................ 892 B.3 List of Supported Commands (Default Roles)................................................................... 903 Appendix C Firmware Version Support for Commands 912 Appendix D Basic Setting Examples 922 D.1 Settings When Using Volumes ......................................................................................... 922 D.1.1 RAID Configuration Setting Procedure ......................................................................................................... 923 D.1.2 Host Access Setting Procedure..................................................................................................................... 924 D.2 Settings for Various Host Accesses ...................................................................................925 D.2.1 Specifying a Host and Performing Mapping (Host Affinity Mode)................................................................ 926 D.2.2 Specifying a Port Group and Performing LUN Mapping................................................................................ 927 D.2.3 Specifying a Port and Setting LUN Mapping ................................................................................................ 927 D.3 Setting Cancellation.........................................................................................................928 D.3.1 Canceling Mapping...................................................................................................................................... 929 D.3.2 Deleting LUN Groups ................................................................................................................................... 929

ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 20 D.3.3 Deleting Port Groups ................................................................................................................................... 930 D.3.4 Deleting Host Groups................................................................................................................................... 930 D.3.5 Deleting Registered Hosts ........................................................................................................................... 930 D.3.6 Deleting Volumes ........................................................................................................................................ 931 D.3.7 Deleting RAID Groups .................................................................................................................................. 931 Appendix E Status List 932 E.1 General Status .................................................................................................................932 E.2 Component Status ........................................................................................................... 932 E.3 Drive Status .....................................................................................................................933 E.4 Volume Status..................................................................................................................933 E.5 Pool Status (TPP/FTRP/FTSP Status)..................................................................................934 E.6 RAID Group Status............................................................................................................934 E.7 Key Status........................................................................................................................ 935 E.8 Key Server Status .............................................................................................................936 Appendix F Default Value List 937

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 21 Chapter 1 Overview The ETERNUS DX command line interface (hereinafter referred to as "CLI") is installed in controllers of the ETERNUS DX. The CLI is used for performing settings and maintenance via commands and command scripts. This chapter describes the outlines for the CLI. 1.1 Accessing CLI The CLI software embedded in each ETERNUS DX controller module enables storage systems to be configured, monitored, and managed. This may be done via LAN connection to the controller module's Ethernet port, using telnet, an SSH application, or a terminal emulator on a remote administrator client. For telnet connection, a user name and password are required. For SSH, in addition to a user name and password, SSH public key authentication is also supported. For details, refer to the "import ssh-publickey" command. Default IP address, user name, and password are as follows: The default IP address is assigned to the following ports. • With the ETERNUS DX100 S3/DX200 S3 or the ETERNUS DX200F RMT port • With the ETERNUS DX500 S3/DX600 S3 FST port The network for the MNT port must be configured from the "set network" command. CLI will display the following pre-login message on the terminal: The date and time are the local values. However, this message may not be displayed when logged in with SSH. This is due to the fact it depends on terminal software. There are no drive enclosures in the ETERNUS DX200F. In addition, the controller enclosure only has SSDs installed. Therefore, functions that are related to drive enclosures, SAS disks, SAS Self Encrypting Drives, or Nearline SAS disks cannot be used. IP address: 192.168.1.1 user name: root password: root ETERNUS login is required. [2010-01-01 05:38:00]

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 22 1.2 The Command Syntax This section explains command syntax. 1.2.1 Command Format The command format is as follows: • Basically, a command name consists of a verb section and an object section (Example: "create volume"). However, there are also some commands that consist of one word (Example: "logoff" and "shutdown"). • A parameter consists of a parameter name section and an operand section. A parameter name is appended with a hyphen (-) before it (Example: "-name"). • An operand is always required after a parameter name (Example: "-name abcdef"). 1.2.2 Keywords and Parameters Command and parameter names are not case-sensitive and can be entered in either or both uppercase and lowercase. Operands, however, are case-sensitive. Any of the printable ASCII codes 0x20 – 0x7e (hexadecimal notation) are allowed as input characters. Note that the following additional restrictions apply: • Question marks (?) cannot be used. • When spaces ( ) are used as characters, they must be enclosed by double quotation marks (") (Example: "ABC DEF","ABC DEF,GHIJKL"). • When double quotation marks (") and single quotation marks (') are used as characters, they must be backslash(\) escaped. Example: "\" 1.2.3 Drive Enclosure Syntax The format that can be used for drive enclosure numbers is either "xx" or "x" ("xx" and "x" indicate hexadecimal numbers). "xx" indicates a two-digit number for the drive enclosure number and "x" indicates a one-digit number for the drive enclosure number. When a two-digit enclosure number is specified, the format "xx" must be used. When a one-digit enclosure number is specified, either format can be specified. For example, "1" can be specified for a one-digit number. However, if the format "xx" is used, 0 must be specified before the enclo- sure number. For example, when an enclosure number is 1, "01" must be specified. For the ETERNUS DX100 S3/DX200 S3, from 1 to a can be specified. For the ETERNUS DX500 S3, from 0 to a and from 10 to 1a can be specified. For the ETERNUS DX600 S3, from 0 to a, from 10 to 1a, from 20 to 2a, and from 30 to 3a can be spec- ified. Command name Parameter Parameter . . . Parameter command-name: Verb section + Object section (Ex: create volume) parameter: Hyphen(-) + Parameter name section + Operand section (Ex: -n 80) There are no drive enclosures in the ETERNUS DX200F.

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 23 1.2.4 Drive Syntax The format that can be used for drive numbers is either "xxyy" or "xyy". "xx" or "x" indicates the enclosure number. For the ETERNUS DX100 S3/DX200 S3 or the ETERNUS DX200F, 00 or 0 indicates the controller enclosure. For details, refer to "1.2.3 Drive Enclosure Syntax" (page 22). The "yy" is the drive number (a two- digit decimal). For a 3.5" drive, between 00 and 11 (a two-digit decimal) can be specified for "yy". For a 2.5" drive, between 00 and 23 can be specified for "yy". For a 3.5" drive in a high-density drive enclosure, from 00 to 59 can be specified for "yy". 2.5" drives in high-density drive enclosures are not supported. Drive numbers can be combined as follows: • A single drive number: 1003 • A list of drive numbers: 1003,004 • A hyphenated range of drive numbers from a to z : 0210-0211 • A list of drive numbers, drive ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 0003,0006,010-011 1.2.5 Alias Name Syntax The format of an alias is a character string that has a maximum of 16 ASCII characters. Usable characters are those given in "1.2.2 Keywords and Parameters" (page 22) of the document overview. Commas (,) cannot be used. 1.2.6 Thin Provisioning Pool Syntax There are two methods for specifying Thin Provisioning Pool identifiers; Thin Provisioning Pool numbers or Thin Provisioning Pool names. • Thin Provisioning Pool number A Thin Provisioning Pool number is automatically created by the system when a Thin Provisioning Pool is created. This is a decimal number. Thin Provisioning Pool numbers can be displayed by using the "show thin-pro-pools" command. Thin Provisioning Pool numbers can be combined as follows: - A single Thin Provisioning Pool number: 1 - A list of Thin Provisioning Pool numbers: 1,8,12 - A hyphenated range of Thin Provisioning Pool numbers from a to z: 2-5 - A list of Thin Provisioning Pool numbers, Thin Provisioning Pool ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 24 • Thin Provisioning Pool name A Thin Provisioning Pool name must be specified when creating a Thin Provisioning Pool. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of Thin Provisioning Pool names. A Thin Provisioning Pool name and a Thin Provisioning Pool number cannot both be specified in the same command. Do not include spaces before or after commas (,). 1.2.7 Flexible Tier Pool Syntax There are two methods for identifying an entered Flexible Tier Sub Pool; Flexible Tier Pool numbers or Flexible Tier Pool names. • Flexible Tier Pool number A Flexible Tier Pool number is automatically created by the system when a Flexible Tier Pool is created. This is a decimal number. Flexible Tier Pool numbers can be displayed by using the "show flexible-tier- pools" command. Flexible Tier Pool numbers can be combined as follows: - A single Flexible Tier Pool number: 1 - A list of Flexible Tier Pool numbers: 1,8,12 - A hyphenated range of Flexible Tier Pool numbers from a to z: 2-5 - A list of Flexible Tier Pool numbers, ranges, or both, separated by commas (,): 1,3,10-12 • Flexible Tier Pool name A Flexible Tier Pool name must be specified when creating a Flexible Tier Pool. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of Flexible Tier Pool names. A Flexible Tier Pool name and a Flexible Tier Pool number cannot both be specified in the same command. Do not include spaces before or after commas (,). • Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. • Since Thin Provisioning Pools and Flexible Tier Sub Pools use the same resource, the same number and name cannot be used for both a Thin Provisioning Pool and a Flexible Tier Sub Pool. If the Thin Provisioning Pool number or the Thin Provisioning Pool name that is specified for a command is already used for an FTSP, the command is not executed. Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions.

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 25 1.2.8 Flexible Tier Sub Pool Syntax There are two methods for identifying an entered Flexible Tier Sub Pool; Flexible Tier Sub Pool numbers or Flexible Tier Sub Pool names. • Flexible Tier Sub Pool number A Flexible Tier Sub Pool number is automatically created by the system when a Flexible Tier Sub Pool is created. This is a decimal number. Flexible Tier Sub Pool numbers can be displayed by using the "show flexible-tier-sub-pools" command. Flexible Tier Sub Pool numbers can be combined as follows: - A single Flexible Tier Sub Pool number: 1 - A list of Flexible Tier Sub Pool numbers: 1,8,12 - A hyphenated range of Flexible Tier Sub Pool numbers from a to z: 2-5 - A list of Flexible Tier Sub Pool numbers, ranges, or both, separated by commas (,): 1,3,10-12 • Flexible Tier Sub Pool name A Flexible Tier Sub Pool name must be specified when creating a Flexible Tier Sub Pool. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of Flexible Tier Sub Pool names. A Flexible Tier Sub Pool name and a Flexible Tier Sub Pool number cannot both be specified in the same command. Do not include spaces before or after commas (,). 1.2.9 RAID Group Syntax There are two methods for specifying RAID group identifiers; RAID group numbers or RAID group names. • RAID group number A RAID group number is automatically created by the system when a RAID group is created. This is a decimal number. RAID group numbers can be displayed by using the "show raid-groups" command. RAID group numbers can be combined as follows: - A single RAID group number: 1 - A list of RAID group numbers: 1,8,12 - A hyphenated range of RAID group numbers from a to z: 2-5 - A list of RAID group numbers, RAID group ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 • Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. • Since Thin Provisioning Pools and Flexible Tier Sub Pools use the same resource, the same number and name cannot be used for both a Thin Provisioning Pool and a Flexible Tier Sub Pool. If the FTSP number or FTSP name that is specified for a command is already used for a Thin Provisioning Pool, the command is not executed.

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 26 • RAID group name A RAID group name must be specified when creating a RAID group. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of RAID group names. A RAID group name and a RAID group number cannot both be specified in the same command. Do not include spaces before or after commas (,). 1.2.10 Volume Syntax There are two methods to specify a volume identifier; a volume number or a volume name. • Volume number A volume number is automatically created by the system when a volume is created. This is a decimal number. Volume numbers can be displayed by using the "show volumes" command. Volume numbers may be combined as follows: - A volume number: 1 - A list of volume numbers: 5,10 - A hyphenated range of volume numbers from a to z: 2-5 - A list of volume numbers, volume ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 • Volume name A volume name with "$SYSVOL" as a prefix cannot be specified when a volume is created or renamed. To specify a volume name, use the volume name that is set when the volume is created. Note that this does not apply when a volume is created or renamed. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of volume names. A volume name and a volume number cannot both be specified in the same command unless a volume is created or renamed. Do not include spaces before or after commas (,). Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions.

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 27 1.2.11 Host Syntax There are two methods to specify a host identifier; a host number or a host name. • Host number A host number is automatically created by the system when a host identifier or a host alias is registered. This is a decimal number. The following types of host identifier are available: - Host WWN name (FC) - SAS address (SAS) - iSCSI host name (iSCSI) The identifier can be displayed by using the following commands: - "show host-wwn-names" - "show host-sas-addresses" - "show host-iscsi-names" Host numbers may be combined as follows: - A single host number: 1 - A list of host numbers: 2,3 - A hyphenated range of host numbers from a to z: 2-5 - A list of host numbers, host ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 • Host name A host alias must be specified when registering a host identifier. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of host names. A host name and a host number cannot both be specified in the same command. Do not include spaces before or after commas (,). Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions.

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 28 1.2.12 LUN Group Syntax There are two methods to specify a LUN group identifier; a LUN group number or a LUN group name. • LUN group number A LUN group number is automatically created by the system when a LUN group is created. This is a decimal number. LUN group numbers can be displayed by using the "show lun-groups" command. LUN group numbers can be combined as follows: - A single LUN group number: 1 - A list of LUN group numbers: 2,8 - A hyphenated range of LUN group numbers from a to z: 2-5 - A list of LUN group numbers, LUN group ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 • LUN group name A LUN group name must be specified when creating a LUN group. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of LUN group names. A LUN group name and a LUN group number cannot both be specified in the same command. Do not include spaces before or after commas (,). 1.2.13 Host Response Syntax There are two methods to specify a host response identifier; a host response number or a host response name. • Host response number The host response number can be assigned by the user. This is a decimal number. A host response number of "#0" is the system default and it cannot be assigned by the user. However, the parameters for host response #0 can be changed. Host response settings can be displayed by using the "show host-response" command. Host response numbers may be combined as follows: - A single host response number: 1 - A list of host response numbers: 2,5 - A hyphenated range of host response numbers from a to z: 2-5 - A list of host response numbers, host response ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 In GUI, "LUN group number" and "LUN group name" is respectively displayed instead of "affinity group number" and "affinity group name". Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions.

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 29 • Host response name A host response name must be specified when registering a host response. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of host response names. A host response name and a host response number cannot both be specified in the same command. Do not include spaces before or after commas (,). 1.2.14 Eco-mode Schedule Syntax There are two methods to specify an Eco-mode schedule identifier; an Eco-mode schedule number or an Eco- mode schedule name. • Eco-mode schedule number An Eco-mode schedule number is automatically created by the system when an Eco-mode schedule is created. This is a decimal number. Eco-mode schedule numbers can be displayed by using the "show eco- schedule" command. Eco-mode schedule numbers may be combined as follows: - A single Eco-mode schedule number: 1 - A list of Eco-mode schedule numbers: 2,5 - A hyphenated range of Eco-mode schedule numbers from a to z: 2-5 - A list of Eco-mode schedule numbers, Eco-mode schedule ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 • Eco-mode schedule name An Eco-mode schedule name must be specified when creating an Eco-mode schedule. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of Eco-mode schedule names. An Eco-mode schedule name and an Eco-mode schedule number cannot both be specified in the same command. Do not include spaces before or after commas (,). 1.2.15 Host Interface Port Syntax A fixed 3-digit "xyz" numbering format is used. "x" indicates the controller module (CM) number, "y" indicates the channel adapter (CA) number, and "z" indicates the host interface port number. For example, "110" indicates CM#1-CA#1-Port#0. Two or more parameters can be specified by separating them with a comma (,). To indicate both CM#0-CA#0-Port#0 and CM#1-CA#1-Port#0, specify "-port 000,110". Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions.

1.2 The Command Syntax ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 30 1.2.16 Port Group Syntax There are two methods to specify an port group identifier; an port group number or an port group name. • Port group number An port group number is automatically created by the system when an port group is created. This is a decimal number. Port group numbers can be displayed by using the "show port-groups" command. Port group numbers may be combined as follows: - A single port group number: 1 - A list of port group numbers: 2,8 - A hyphenated range of port group numbers from a to z: 2-5 - A list of port group numbers, port group ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 • Port group name An port group name must be specified when creating an port group. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of port group names. An port group name and an port group number cannot both be specified in the same command. Do not include spaces before or after commas (,). 1.2.17 Host Group Syntax There are two methods to specify an host group identifier; an host group number or an host group name. • Host group number An host group number is automatically created by the system when an host group is created. This is a decimal number. Host group numbers can be displayed by using the "show host-groups" command. Host group numbers may be combined as follows: - A single host group number: 1 - A list of host group numbers: 2,8 - A hyphenated range of host group numbers from a to z: 2-5 - A list of host group numbers, host group ranges, or both, separated by commas (,). Spaces are not permitted before or after commas (,): 1,3,10-12 • Host group name An host group name must be specified when creating an host group. For details about the syntax, refer to "1.2.5 Alias Name Syntax" (page 23). Some commands accept a comma-separated list of host group names. An host group name and an host group number cannot both be specified in the same command. Do not include spaces before or after commas (,). Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions. Two or more parameters might not be able to be specified for several commands. For details, refer to the command descriptions.

1.3 Size of Drives and Logical Units ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 31 1.3 Size of Drives and Logical Units The size of drives and logical units (such as RAID groups and volumes) are presented in base 2 (binary) formats. 1.4 Command Auto-complete and History Recall CLI supports an auto-complete command function and also a command history recall function. When using the auto-complete command function, if too few letters are entered to uniquely identify a keyword, the CLI lists keywords that match the entered string and redisplays the string so it can be completed. The auto- complete function applies to a command name, a parameter name and an operand name. It does NOT apply when two or more operands are used that are separated with a comma (,). Except for operand names, even if not all the letters of the keyword are not entered, once enough letters are entered to identify a unique keyword, it is handled as a complete character string. The history contains all the commands entered in the active CLI session. A command from the history can be recalled, edited, and run. For details about usable keys, refer to "1.5 Command Editing Hotkeys" (page 32). Unit Size in binary Kilobyte (KB) 1024 bytes Megabyte (MB) 1024KB (1,048,576 bytes) Gigabyte (GB) 1024MB (1,073,741,824 bytes) Terabyte (TB) 1024GB (109,951,162,776 bytes)

1.5 Command Editing Hotkeys ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 32 1.5 Command Editing Hotkeys The following table lists the CLI command editing functions: To Press Complete a partially entered keyword Tab Get previous command from history Up Arrow, Ctrl-P, or Ctrl-p Get next command from history Down Arrow, Ctrl-N, or Ctrl-n Move cursor left Left Arrow, Ctrl-B, or Ctrl-b Move cursor right Right Arrow, Ctrl-F, or Ctrl-f Move back one word Esc-B or Esc-b Move forward one word Esc-F or Esc-f Move cursor to start of line Ctrl-A or Ctrl-a Move cursor to end of line Ctrl-E or Ctrl-e Transpose current and previous character Ctrl-T or Ctrl-t Delete current character Ctrl-D or Ctrl-d Delete previous character Ctrl-H or Ctrl-h Delete word up to cursor Ctrl-W or Ctrl-w Delete rest of word Esc-D or Esc-d Delete text up to cursor Ctrl-U or Ctrl-u Delete the rest of a line Ctrl-K or Ctrl-k Convert the rest of a word to uppercase Esc-C or Esc-c Convert the rest of a word to lowercase Esc-L or Esc-l Enter command and redisplay prompt Ctrl-Z or Ctrl-z Refresh input line Ctrl-L or Ctrl-l

1.6 Viewing Command Help ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 33 1.6 Viewing Command Help By inputting a question mark (?) after the CLI command name or the parameter name, a brief description can be displayed. By using the "help" command, the command syntax can also be displayed. For further information, refer to the "help" command. # If a question mark [?] is entered by itself, the entire verb list is displayed. CLI> ? copy - copy create - create delete - delete discover - discover exit - Exit the CLI sessions. ... (snip) # If [s?] is entered, all the verbs beginning with "s" are displayed. CLI> s? set show start stop # If [show ?] is entered (note the space between the "show" and "?"), only the "show" command is possible, so all the "show" command objects are displayed. CLI> show ? advanced-copy-licens - Display the Extended Advanced Copy license status. advanced-copy-parame - Display the Advanced Copy parameters. advanced-copy-policy - Display the currently registered Advance Copy policy. advanced-copy-sessio - Display the list of Advance Copy sessions. lun-groups - Display a list of lun groups or display the details of a specified lun group. ... (snip) # If [show m?] is entered, all the "show" command objects beginning with "m" are displayed. CLI> show m? mapping migration # If [create raid-group ?] is entered (note the space between the "create raid-group" and "?"), the parameters that can be specified for the "create raid-group" command are displayed. # Bracketed parameters are optional. All other parameters are required. CLI> create raid-group ? -name - Name of a RAID group -disks - Disks to use in the RAID group -level - RAID level [-assigned-cm] - Assigned controller for the RAID group # Long parameters and command names are truncated at 20 characters, as in the following example. # Note that one or more spaces are required before a question mark. CLI> show host-response ? [-host-response-num - Host response numbers to display details [-host-response-nam - Host response names to display details

1.7 Error Message Format ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 34 1.7 Error Message Format This section explains the CLI error messages format. When the CLI command ends normally, there is no output on the terminal and the CLI prompt is returned to the next line. If an error occurs, an error message is displayed. For further details of the error messages, refer to "Appendix A Error Messages/Error Codes" (page 827). A: Error message number (fixed 4 digits) B: Error message (human-readable message) C: Internal error code (fixed 4 digits + hyphen + fixed 4 digits) D: Details (the specified parameters, etc.) Note that there are messages without an error message number. The location of the error is indicated by a circumflex (^). This will display where there is a syntax error. Check the input parameters and the error message as indicated by the circumflex (^). The following are examples. 1.8 Multiple Sessions A maximum of 16 CLI sessions can run on a single system simultaneously (including accesses with the Software role). A session for an exclusive resource may conflict with a GUI session or another CLI session. When a resource is locked by exclusive access control, the command terminates with an error message. If this occurs, wait until the GUI session or another CLI session that uses the locked resource completes, and then execute the command again. Resources can be forcibly released by using the "set clienv-force-unlock" command. This is useful when a terminal is suddenly disconnected or unexpected errors occur. Error: E0019 Inconsistent parameter. A B [001C-0002] -disks 003 C D CLI> create raid-group -a ^ Error: Missing parameter data CLI> show disks -de 1 -de 2 ^

1.9 Slave Controller Logins ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 35 1.9 Slave Controller Logins For dual controller ETERNUS DX models, at any given time one of the controllers is the master and the other the slave. Normal logins are to the master controller, and are able to access all the normal functions. However, if the master controller becomes inaccessible, a redundant IP address function is available that allows a (reduced functionality) login to the slave controller. Slave controller login is only possible if a redundant IP address has been preset, and only some of the "show" commands to check the status of components are available. It also allows the "change master" command to be used to forcibly swap the master-slave relationship of the two controllers. The "change master" command can only be used by a user account that has the Maintenance Operation policy and that is logged in to the slave controller. Commands that are not supported by the current login type will fail with an error message if attempted. 1.10 CLI User Authority User authority is determined by the role and user policy. For details on roles and user policies, refer to "5.1 User Management" (page 467). 1.11 Note for Specifying FTP Server If an FTP server is specified by domain name format, name resolution is performed by the DNS servers assigned to the specified Ethernet port. If an FTP server is specified by an IP address, an appropriate Ethernet port is automatically assigned by the system. Even though designation of an Ethernet port by using CLI is not required, doing so allows the operator to specify which network the FTP server belongs to.

1.12 Command Descriptions ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 36 1.12 Command Descriptions This section explains the commands in a functional order. Each command topic includes one or more of the following sections. • Description A description of the command • Syntax The command syntax • Parameters A description of parameter(s) • Output (only for reference commands) A description of information displayed by the command • Example(s) One or more examples of the command

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 37 Chapter 2 Status Display This chapter explains the commands related to storage system status. 2.1 Storage System Status This section explains the commands that display the status of the system. Display Items The command syntax Summary status of the system show status Summary status of each enclosure show enclosure-status Controller enclosure status show enclosure-status -type ce Drive enclosure status show enclosure-status -type de -de enclosure_number Controller enclosure and the status of all drive enclosure show enclosure-status -type all Controller module status show fru-ce -type {cm0|cm1} PSU status in controller enclosures show fru-ce -type {psu0|psu1} The status of all components in controller enclosures show fru-ce Expander status in a specific drive enclosure show fru-de -de enclosure_number -type {exp0|exp1} The status of all expanders in all drive enclosures show fru-de -type {exp0|exp1} Fan Expander Module status in a specific drive enclosure show fru-de -de enclosure_number -type {fem0|fem1} The status of all Fan Expander Modules in all drive enclosures show fru-de -type {fem0|fem1} PSU status in a specific drive enclosure show fru-de -de enclosure_number -type {psu0|psu1|psu2|psu3} The status of all PSUs in all drive enclosures show fru-de -type {psu0|psu1|psu2|psu3} The status of all components in a specific drive enclosure show fru-de -de enclosure_number The status of all components in all drive enclosures show fru-de The status of all undefined disks show disks -type undefined The status of all disks in the controller enclosure show disks -type ce The status of all disks in a specific drive enclosure show disks -type de -de enclosure_number Details of specific disks show disks -disks disks Details of all disks show disks -disks all Product IDs of all disks' show disks -disks productid Hardware information show hardware-information

2.1 Storage System Status > show status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 38 show status This command displays a summary of the system status. It will display if any components in the system are in an error or warning condition. It does not indicate if host servers are able to access the system. ■ Syntax ■ Parameters No parameters. ■ Output ■ Example(s) show status Summary status Summary of the system status. Empty The ETERNUS DX is not defined or installed. Normal The ETERNUS DX is in normal state. Pinned Data PIN data exists in the ETERNUS DX. Unused An undefined component is installed in the ETERNUS DX. Warning A component that is the target for preventive maintenance exists in the ETERNUS DX. Maintenance Maintenance is currently being performed on the ETERNUS DX. Error A component with an error exists in the ETERNUS DX. Loop Down The ETERNUS DX is in BackEnd Down state. Not Ready "Not Ready" is a status where an abnormality is detected at a power-off, and I/O access from the host cannot be received. Subsystem Down The ETERNUS DX is not available. Change Assigned CM Hot expansion and recovery of the controller is required. The following example displays a summary of the system status: CLI> show status Summary Status [Normal] CLI> show status Summary Status [Error] CLI> show status Summary Status [Warning]

2.1 Storage System Status > show enclosure-status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 39 show enclosure-status This command displays a summary of the controller enclosure or the drive enclosure status. Details will be displayed if the type of enclosure is specified. ■ Syntax ■ Parameter ■ Output show enclosure-status [-type { all|ce|de [-de enclosure_number]} ] -type Optional. This parameter specifies the enclosure type. If the type is omitted, only summary information will be displayed. all Detailed status of both the controller enclosure and all the drive enclosures are displayed. ce Detailed status of the controller enclosure is displayed. de Detailed status of the specified drive enclosure is displayed. -de Optional. This parameter can specify the drive enclosure number only when a drive enclosure type is specified. For details, refer to "1.2.3 Drive Enclosure Syntax" (page 22). If this parameter is omitted, all of the drive enclosures are selected. Other enclosure types cannot be specified. Example: -type de -de 1 (When requesting drive enclosure #1 details) The following information is the output information when all the parameters are omitted: Storage System Name ETERNUS DX name Model Upgrade Status Model upgrade status. This indicates whether or not the model can or has been upgraded. If the model can and has been upgraded, [Upgraded] is displayed. If the model can but has not been upgraded yet, [Not Upgraded] is displayed. If the model cannot be upgraded, [Not Possible] is displayed. Model Name Model name of the system Serial Number Serial number of the system Device Identification Number Device identification number used by the ETERNUS Multipath Driver or other external software to identify the storage system. Status Status of the system

2.1 Storage System Status > show enclosure-status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 40 Cache Mode The cache control mode (Write Back Mode or Write Through Mode) Remote Support The remote support state (Operating, Maintenance, Stopping, or Not yet Set) Stopping indicates a temporarily stopped status. Operation Mode The operation mode (Normal (normal operation mode) or Maintenance Mode (Maintenance mode)) CLI Connecting Controller Module Controller module that has an active CLI connection. Firmware Version Current firmware version Example: Firmware Version [V10L10-0000 for Unified Storage] (When using a unified storage system.) Firmware Version [V10L10-0000] (When a unified storage system is not used.) Controller Enclosure Controller enclosure status Drive Enclosure #n Indicates the number of the drive enclosure and its status Example: Drive Enclosure #1 [ status ] (giving the status of drive enclosure) System Message Messages that identify the error events that have occurred in the system. The following information is output for the controller enclosure components: Intake Temp Intake temperature status, status code, and intake temperature values. Each controller has two redundant intake temperature sensors, and both temperature values is displayed in Celsius. If a sensor fails, "Failed" is displayed. Exhaust Temp Exhaust temperature status, status code, and exhaust temperature values. Each controller has two redundant exhaust temperature sensors, and both temperature values is displayed in Celsius. If a sensor fails, "Failed" is displayed. CM#n Controller Module status and the status code. The "#n" in the field indicates the controller module number. Example: CM#1 [Status / Status Code] (For controller module#1) CM#n PFM#n Controller Module’s PCIe Flash Module status and the status code (only for the ETERNUS DX500 S3/DX600 S3). The "#n" in the field indicates the controller module number and the "#m" in the field indicates the PCIe Flash Module number.

2.1 Storage System Status > show enclosure-status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 41 PSU#n Power Supply Unit status and the status code. The "#n" in the field indicates the Power Supply Unit number. Example: PSU#1 [Status / Status Code] (For Power Supply Unit#1) DISK#xyy Disk status (only for the ETERNUS DX100 S3/DX200 S3 and the ETERNUS DX200F) Example: CE-Disk#1 [ status ] (Disk #001 status) (For details, refer to "1.2.4 Drive Syntax" (page 23).) The following information is displayed if the device enclosure is specified: Intake Temp Intake TempIntake temperature status, status code, and intake temperature values. Each controller has two redundant intake temperature sensors, and both temperature values is displayed in Celsius. If a sensor fails, "Failed" is displayed. Exhaust Temp Exhaust temperature status and the status code. Note that exhaust temperature values are not displayed. IOM#0 I/O module #0 status and the status code IOM#1 I/O module #1 status and the status code FEM#0 Fan Expander Module #0 status and the status code (This information only appears for high-density drive enclosures) FEM#0 EXP#0 Status of Expander #0 in Fan Expander Module #0 and the status code (This information only appears for high-density drive enclosures) FEM#0 EXP#1 Status of Expander #1 in Fan Expander Module #0 and the status code (This information only appears for high-density drive enclosures) FEM#1 Fan Expander Module #1 status and the status code (This information only appears for high-density drive enclosures. This information is displayed regardless of the CM num- ber.) FEM#1 EXP#0 Status of Expander #0 in Fan Expander Module #1 and the status code (This information only appears for high-density drive enclosures. This information is displayed regardless of the CM number.) FEM#1 EXP#1 Status of Expander #1 in Fan Expander Module #1 and the status code (This information only appears for high-density drive enclosures. This information is displayed regardless of the CM number.) PSU#0 Power Supply Unit #0 status and the status code PSU#1 Power Supply Unit #1 status and the status code

2.1 Storage System Status > show enclosure-status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 42 ■ Example(s) PSU#2 Power Supply Unit #2 status and the status code (This information only appears for high- density drive enclosures) PSU#3 Power Supply Unit #3 status and the status code (This information only appears for high- density drive enclosures) DISK#xyy Disk status Example: DE#1-Disk#1 [ status ] (Disk #101 status) (For details, refer to "1.2.4 Drive Syntax" (page 23).) The following information is displayed when no parameters are specified: CLI> show enclosure-status Enclosure View Storage System Name [ETERNUS DX100] Model Upgrade Status [Not Possible] Model Name [ET06F21A] Serial Number [000000] Device Identification Number [010000] Status [Normal] Cache Mode [Write Back Mode] Remote Support [Not yet Set] Operation Mode [Maintenance Mode] CLI Connecting Controller Module [CM#0] Firmware Version [V10L11-0000] Controller Enclosure (3.5") [Normal] Drive Enclosure #1 (2.5" 24DE) [Error] Drive Enclosure #2 (3.5" 12DE) [Error] Drive Enclosure #3 (3.5" 60DE) [Error] System Message No. Message 1 P 100000XX-XXXXX 2 P 500000XX-XXXXX The following example shows the information that is displayed when the controller enclosure is specified for the ETERNUS DX100 S3/DX200 S3: CLI> show enclosure-status -type ce Controller Enclosure Information Location Status Error Code Sensor 1 / Sensor 2 Intake Temp Normal 0x0000 25 (C) / 25 (C) Exhaust Temp Normal 0x0000 25 (C) / 25 (C) Controller Enclosure Status Controller Module Status/Status Code CM#0 [Normal / 0xE001] CM#1 [Normal / 0xE001] Power Supply Unit Status/Status Code PSU#0 [Normal / 0xE001] PSU#1 [Normal / 0xE001] Disk Status CE-Disk#0 [Rebuild/Copyback ] CE-Disk#1 [Rebuild/Copyback ] CE-Disk#2 [Available ] CE-Disk#3 [Broken ] CE-Disk#4 [Available ] CE-Disk#5 [Available(Predictive Failure)] CE-Disk#6 [Available(Predictive Failure)] CE-Disk#7 [Present ] CE-Disk#8 [Present ] CE-Disk#9 [Present ] CE-Disk#10 [Present ] CE-Disk#11 [Spare ]

2.1 Storage System Status > show enclosure-status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 43 The following example shows the information that is displayed when the controller enclosure is specified for the ETERNUS DX500 S3/DX600 S3: CLI> show enclosure-status -type ce Controller Enclosure Information Location Status Error Code Sensor 1 / Sensor 2 Intake Temp Normal 0x0000 25 (C) / 25 (C) Exhaust Temp Normal 0x0000 25 (C) / 25 (C) Controller Enclosure Status Controller Module Status/Status Code CM#0 [Normal / 0xE001] CM#1 [Normal / 0xE001] PCIe Flash Module Status/Status Code CM#0 PFM#0 [Normal / 0xE001] CM#0 PFM#1 [Normal / 0xE001] CM#1 PFM#0 [Normal / 0xE001] CM#1 PFM#1 [Normal / 0xE001] Power Supply Unit Status/Status Code PSU#0 [Normal / 0xE001] PSU#1 [Normal / 0xE001] The following example shows the information that is displayed when drive enclosure #1 is specified: CLI> show enclosure-status -type de -de 1 Drive Enclosure #1 Information Location Status Error Code Sensor 1 / Sensor 2 Intake Temp Normal 0x0000 25 (C) / 25 (C) Exhaust Temp Normal 0x0000 - / - Drive Enclosure #1 Status I/O Module Status/Status Code IOM#0 [Normal / 0xE001] IOM#1 [Normal / 0xE001] Power Supply Unit Status/Status Code PSU#0 [Normal / 0xE001] PSU#1 [Normal / 0xE001] Disk Status DE#1-Disk#0 [Available ] DE#1-Disk#1 [Available ] DE#1-Disk#2 [Available ] DE#1-Disk#3 [Rebuild/Copyback ] DE#1-Disk#4 [Rebuild/Copyback ] DE#1-Disk#5 [Available ] DE#1-Disk#6 [Available ] DE#1-Disk#7 [Available(Predictive Failure)] DE#1-Disk#8 [Available ] DE#1-Disk#9 [Available ] DE#1-Disk#10 [Available(Predictive Failure)] DE#1-Disk#11 [Broken ]

2.1 Storage System Status > show enclosure-status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 44 The following example shows the information that is displayed when drive enclosure #1 (high-density drive enclosure) is specified: CLI> show enclosure-status -type de -de 1 Drive Enclosure #1 Information Location Status Error Code Sensor 1 / Sensor 2 Intake Temp Normal 0x0000 25 (C) / 25 (C) Exhaust Temp Normal 0x0000 - / - Drive Enclosure #1 Status I/O Module Status/Status Code IOM#0 [Normal / 0xE001] IOM#1 [Normal / 0xE001] Fan Expander Module Status/Status Code FEM#0 [Normal / 0xE001] FEM#0 EXP#0 [Normal / 0xE001] FEM#0 EXP#1 [Normal / 0xE001] FEM#1 [Normal / 0xE001] FEM#1 EXP#0 [Normal / 0xE001] FEM#1 EXP#1 [Normal / 0xE001] Power Supply Unit Status/Status Code PSU#0 [Normal / 0xE001] PSU#1 [Normal / 0xE001] PSU#2 [Normal / 0xE001] PSU#3 [Normal / 0xE001] Disk Status DE#1-Disk#0 [Available ] DE#1-Disk#1 [Available ] DE#1-Disk#2 [Available ] DE#1-Disk#3 [Rebuild/Copyback ] DE#1-Disk#4 [Rebuild/Copyback ] DE#1-Disk#5 [Available ] DE#1-Disk#6 [Available ] DE#1-Disk#7 [Available(Predictive Failure)] DE#1-Disk#8 [Available ] DE#1-Disk#9 [Available ] DE#1-Disk#10 [Available(Predictive Failure)] DE#1-Disk#11 [Broken ] DE#1-Disk#12 [Available ] DE#1-Disk#13 [Available ] DE#1-Disk#14 [Available ] DE#1-Disk#15 [Available ] DE#1-Disk#16 [Available ] DE#1-Disk#17 [Available ] DE#1-Disk#18 [Available ] DE#1-Disk#19 [Available ] DE#1-Disk#20 [Available ] DE#1-Disk#21 [Available ] DE#1-Disk#22 [Available ] DE#1-Disk#23 [Available ] DE#1-Disk#24 [Available ] DE#1-Disk#25 [Available ] DE#1-Disk#26 [Available ] DE#1-Disk#27 [Available ] DE#1-Disk#28 [Available ] DE#1-Disk#29 [Available ] DE#1-Disk#30 [Available ] DE#1-Disk#31 [Available ] DE#1-Disk#32 [Available ] DE#1-Disk#33 [Available ] DE#1-Disk#34 [Available ] DE#1-Disk#35 [Available ] DE#1-Disk#36 [Available ] DE#1-Disk#37 [Available ] DE#1-Disk#38 [Available ] DE#1-Disk#39 [Available ] DE#1-Disk#40 [Available ] DE#1-Disk#41 [Available ] DE#1-Disk#42 [Available ] DE#1-Disk#43 [Available ] DE#1-Disk#44 [Available ] DE#1-Disk#45 [Available ] DE#1-Disk#46 [Available ] DE#1-Disk#47 [Available ] DE#1-Disk#48 [Available ] DE#1-Disk#49 [Available ] DE#1-Disk#50 [Available ] DE#1-Disk#51 [Available ] DE#1-Disk#52 [Available ] DE#1-Disk#53 [Available ] DE#1-Disk#54 [Available ] DE#1-Disk#55 [Available ] DE#1-Disk#56 [Available ] DE#1-Disk#57 [Available ] DE#1-Disk#58 [Available ] DE#1-Disk#59 [Available ]

2.1 Storage System Status > show enclosure-status ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 45 The following example shows the information that is displayed when all of the enclosures are specified: CLI> show enclosure-status -type all Controller Enclosure Information Location Status Error Code Sensor 1 / Sensor 2 Intake Temp Normal 0x0000 25 (C) / 25 (C) Exhaust Temp Normal 0x0000 25 (C) / 25 (C) Controller Enclosure Status Controller Module Status/Status Code CM#0 [Normal / 0xE001] CM#1 [Normal / 0xE001] Power Supply Unit Status/Status Code PSU#0 [Normal / 0xE001] PSU#1 [Normal / 0xE001] Disk Status CE-Disk#0 [Rebuild/Copyback ] CE-Disk#1 [Rebuild/Copyback ] CE-Disk#2 [Available ] CE-Disk#3 [Broken ] CE-Disk#4 [Available ] CE-Disk#5 [Available(Predictive Failure)] CE-Disk#6 [Available(Predictive Failure)] CE-Disk#7 [Present ] CE-Disk#8 [Present ] CE-Disk#9 [Present ] CE-Disk#10 [Present ] CE-Disk#11 [Spare ] Drive Enclosure #1 Information Location Status Error Code Sensor 1 / Sensor 2 Intake Temp Normal 0x0000 25 (C) / 25 (C) Exhaust Temp Normal 0x0000 - / - Drive Enclosure #1 Status I/O Module Status/Status Code IOM#0 [Normal / 0xE001] IOM#1 [Normal / 0xE001] Power Supply Unit Status/Status Code PSU#0 [Normal / 0xE001] PSU#1 [Normal / 0xE001] Disk Status DE#1-Disk#0 [Available ] DE#1-Disk#1 [Available ] DE#1-Disk#2 [Available ] DE#1-Disk#3 [Rebuild/Copyback ] DE#1-Disk#4 [Rebuild/Copyback ] DE#1-Disk#5 [Available ] DE#1-Disk#6 [Available ] DE#1-Disk#7 [Available(Predictive Failure)] DE#1-Disk#8 [Available ] DE#1-Disk#9 [Available ] DE#1-Disk#10 [Available(Predictive Failure)] DE#1-Disk#11 [Broken ]

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 46 show fru-ce This command displays the status of components (Field Replaceable Units) of the controller enclosure. ■ Syntax ■ Parameter ■ Output show fru-ce [-type {cm0|cm1|psu0|psu1}] -type Optional. This parameter specifies the target component (FRU) name. The details and status of each component embedded in the controller enclosure will be displayed. Only one parameter can be specified. If this parameter is omitted, all of the FRUs are displayed. cm0 Details and status of the Controller Module Unit #0 and the sub-components cm1 Details and status of the Controller Module Unit #1 and the sub-components psu0 Details and status of the Power Supply Unit #0 psu1 Details and status of the Power Supply Unit #1 The following table shows the output information when the controller module and the sub-components are specified: CM#n Information (n: The controller module number) CPU Status/Status Code Controller Module (CM#n) status and the status code Memory Size Memory size of a controller module Parts Number Parts number Serial Number Serial number Hardware Revision Hardware version CPU Clock CPU clock frequency CM Active EC EC number of the active firmware (The current operating firmware) CM Next EC EC number of the stand-by firmware (The generation number of the firmware after the next power cycle)

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 47 BIOS Active EC EC number of the active firmware (The current operating firmware) BIOS Next EC EC number of the stand-by firmware (The generation number of the firmware after the next power cycle) CM EXP Active EC EC number of the active firmware (The current operating firmware) CM EXP Next EC EC number of the stand-by firmware (The generation number of the firmware after the next power cycle) NAS Engine Information This information only appears when the NAS function is enabled. Status/Status Code NAS function status and the status code CM#n Internal Parts Status and Status Code (n: The controller module number) Memory# Memory status and the status code Memory# Parts Number Memory parts number Memory# Serial Number Memory serial number Memory# Hard Revision Memory hardware revision BUD# BUD (Bootup and Utility Device) status and the status code BUD# Parts Number BUD parts number BUD# Serial Number BUD serial number BUD# Hard Revision BUD hardware revision CM FAN CM FAN status and the status code (ETERNUS DX500 S3/DX600 S3 only) CA# Parts Number CA parts number CA# Serial Number CA serial number CA# Hard Revision CA hardware revision

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 48 CA Slot# CA Slot status and the status code DMA Port# DMA Port status and the status code BIOS# BIOS status and the status code CM EXP CM EXP status and the status code CM EXP# InPort# CM EXP InPort status and the status code SAS Cable# (OUT) SAS Cable (OUT) status and the status code CM RTC CM RTC status and the status code CM NVRAM CM NVRAM status and the status code CM FPGA CM FPGA status and the status code CM LAN Port# CM LAN Port status and the status code DI# Port# DI port status and the status code SATA SSD Controller Boot and Utility Device (BUD) controller status and the status code (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) SATA SSD Controller Active EC Edition Control (EC) number that is currently operating in the relevant BUD controller (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) SATA SSD Controller Next EC EC number that will start up next in the relevant BUD controller (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) SATA SSD Controller Firmware Version BUD controller firmware version (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) SCU SCU (System Capacitor Unit) status and the status code (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) SCUs are electric double layer capacitors embedded in a controller module. SCUs provide the power to move the cache data to the SATA SSD flash memory if there is a power outage. SCU Voltage Charging voltage of SCU (ETERNUS DX100 S3/DX200 S3 and ETERNUS DX200F only) PCH PCH status and the status code

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 49 CM#n CA#m Port#l Information (n: The controller module number, m: The Channel Adapter number, l: The port number) (For FC, iSCSI, FCoE, and SAS) Port Type Indicates whether the host interface port type is FC, iSCSI, FCoE, or SAS. Port Mode Indicates whether the host interface port mode is CA, RA, CA/RA auto, or Initiator. Status/Status Code Host interface Port (Port#m) status and the status code Multiple VLAN This information only appears when the port type is a 2-port 1G-iSCSI (Hilda) or a 2-port 10G-iSCSI (Hilda). This information indicates whether multiple VLAN is enabled. When multiple VLAN is enabled, "Enable" is displayed. When multiple VLAN is disabled, "Disable" is disabled. When the port mode is RA, "-" is displayed. Number of IP Addresses This information only appears when the port type is a 2-port 1G-iSCSI (Hilda) or a 2-port 10G-iSCSI (Hilda). This information indicates the number of IP addresses with enabled ports. When "Enable" is displayed for the Multiple VLAN item, the number of IP addresses with enabled ports (from 1 to 16) is displayed. When "Disable" or "-" is displayed for the Mul- tiple VLAN item, "1" is displayed. CA Active EC EC number of the active firmware (the current operating firmware) CA Next EC EC number of the stand-by firmware (the generation number of the firmware after the next power cycle) Connection Connection condition Loop ID Loop ID Transfer Rate Transfer rate (A value specified by the operator) Link Status Link status (Link Up, Link Down, or if requesting auto negotiation, then the actual transfer rate is displayed.) Port WWN Port World-Wide-Name Node WWN Node World-Wide-Name iSCSI Name iSCSI Name iSCSI Alias Name iSCSI Alias Name

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 50 Host Affinity Indicates whether Host Affinity Mode is enabled. Host Response Host response information assigned to this port iSNS Server Port No iSNS Server Port Number TCP Port No TCP Port Number TCP Window Size TCP Window Size FC Frame Size FC Frame Size VLAN ID VLAN ID Header Digest Indicates whether or not Header Digest is added. Date Digest Indicates whether or not Date Digest is added. Bandwidth Limit Bandwidth limit (upper limit performance value) Target Portal Group Number Target Portal Group Number CmdSN Count CmdSN Count Err Recovery Lvl Error Recovery Level Task Retain Time The time required for processes stopped due to disconnection to restart from where they were stopped after reconnection Reconnection Wait Time The time required to reconnect the TCP connection Fabric Name Fabric Name SFP Type SFP Type

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 51 SFP Information (For FC, iSCSI 10G, and FCoE) Temperature Temperature (Present, Warning(Low/High), and Alarm(Low/High)) Voltage Voltage (Present, Warning(Low/High), and Alarm(Low/High)) Current Current (Present, Warning(Low/High), and Alarm(Low/High)) TX Power Transmitter power (Present, Warning(Low/High), and Alarm(Low/High)) RX Power Receiver power (Present, Warning(Low/High), and Alarm(Low/High)) CM#n CA#m Port#l Information (n: The controller module number, m: The Channel Adapter number, l: The port number) (For NAS) Port Type Host interface port type (NAS) Status/Status Code Host interface port status and the status code CA Active EC EC number of the active firmware (the current operating firmware) CA Next EC EC number of the stand-by firmware (the generation number of the firmware after the next power cycle) MAC Address MAC address of the port SFP Type SFP type of the port (for 10G NAS). (This information does not appear when 1G NAS is used) SFP Information (For 10G NAS) (The following information does not appear when 1G NAS is used) Temperature Temperature (Present, Warning(Low/High), and Alarm(Low/High)) Voltage Voltage (Present, Warning(Low/High), and Alarm(Low/High)) Current Current (Present, Warning(Low/High), and Alarm(Low/High)) TX Power Transmitter power (Present, Warning(Low/High), and Alarm(Low/High)) RX Power Receiver power (Present, Warning(Low/High), and Alarm(Low/High))

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 52 CM#n PFM#m Information (n: The controller module number, m: The PCIe Flash Module number) (The following information appears when the ETERNUS DX500 S3/DX600 S3 is used) Type PCIe Flash Module type Status/Status Code PCIe Flash Module status and the status code Health Remaining capacity (operating life) of the PCIe Flash Module (as a percentage). When the remaining capacity is 5% or less, "Warning" appears in the Status/Status Code field. When the remaining capacity is 0%, "Error" appears in the Status/Status Code field. Capacity PCIe Flash Module physical capacity Parts Number PCIe Flash Module parts number Serial Number PCIe Flash Module serial number Hard Revision PCIe Flash Module hardware revision BCU/BTU Information (The following information appears when the ETERNUS DX500 S3/DX600 S3 is used) BCU Status/Status Code PCIe Flash Module type BCU Status/Status Code BTU status and the status code BCU# ChargeRate Charging rate of BCU BCU# Expires Expiry date of the BCU BCU# Parts Number BCU parts number BCU# Serial Number BCU serial number BCU# Hard Revision BCU hardware revision The following table shows the output information of the power supply units. Status/Status Code Power supply unit (PSU#n) status and the status code

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 53 ■ Example(s) The following example displays the status and details of controller module #0 for FC (For ETERNUS DX100 S3/ DX200 S3, ETERNUS DX500 S3/DX600 S3): CLI> show fru-ce -type cm0 CM#0 Information CPU Status/Status Code [Normal / 0xE001] Memory Size [1.5GB] Parts Number [] Serial Number [] Hard Revision [] CPU Clock [2.00GHz] CM Active EC [EC#1] CM Next EC [EC#1] BIOS Active EC [EC#0] BIOS Next EC [EC#0] CM EXP Active EC [EC#1] CM EXP Next EC [EC#1] NAS Engine Information Status/Status Code [Normal / 0xE001] CM#0 Internal Parts Status/Status Code Memory#0 [Normal / 0xE001] Memory#0 Parts Number [18JSF25672PZ-1G1F0] Memory#0 Serial Number [0951D864C0D0] Memory#0 Hard Revision [4631] Memory#1 [Undefined / 0x0000] Memory#1 Parts Number [] Memory#1 Serial Number [] Memory#1 Hard Revision [] Memory#2 [Undefined / 0x0000] Memory#2 Parts Number [] Memory#2 Serial Number [] Memory#2 Hard Revision [] Memory#3 [Undefined / 0x0000] Memory#3 Parts Number [] Memory#3 Serial Number [] Memory#3 Hard Revision [] Memory#4 [Undefined / 0x0000] Memory#4 Parts Number [] Memory#4 Serial Number [] Memory#4 Hard Revision [] Memory#5 [Undefined / 0x0000] Memory#5 Parts Number [] Memory#5 Serial Number [] Memory#5 Hard Revision [] Memory#6 [Undefined / 0x0000] Memory#6 Parts Number [] Memory#6 Serial Number [] Memory#6 Hard Revision [] Memory#7 [Undefined / 0x0000] Memory#7 Parts Number [] Memory#7 Serial Number [] Memory#7 Hard Revision [] BUD [Normal / 0xE001] BUD Parts Number [QEMU HARDDISK QM00] BUD Serial Number [QM00002 0 10] BUD Hard Revision [0 10 6 ] CM FAN [Normal / 0xE001] CA#0 Parts Number [] CA#0 Serial Number [] CA#0 Hard Revision [] CA Slot#0-0 [Normal / 0xE001] CA Slot#0-1 [Undefined / 0x0000] CA#1 Parts Number [] CA#1 Serial Number [] CA#1 Hard Revision [] CA Slot#1-0 [Undefined / 0x4000] CA Slot#1-1 [Undefined / 0x0000] CA#2 Parts Number [] CA#2 Serial Number [] CA#2 Hard Revision [] CA Slot#2-0 [Undefined / 0x0000] CA Slot#2-1 [Undefined / 0x0000]

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 54 CA#3 Parts Number [] CA#3 Serial Number [] CA#3 Hard Revision [] CA Slot#3-0 [Undefined / 0x0000] CA Slot#3-1 [Undefined / 0x0000] DMA Port#0 [Normal / 0xE001] DMA Port#1 [Normal / 0xE001] BIOS#0 [Normal / 0xE001] BIOS#1 [Normal / 0xE001] CM EXP [Normal / 0xE001] CM EXP InPort#0 [Normal / 0xE001] CM EXP InPort#1 [Normal / 0xE001] CM EXP InPort#2 [Undefined / 0xE001] CM EXP InPort#3 [Undefined / 0xE001] SAS Cable#0(OUT) [Normal / 0xE001] SAS Cable#1(OUT) [Undefined / 0x0000] SAS Cable#2(OUT) [Undefined / 0x0000] SAS Cable#3(OUT) [Undefined / 0x0000] CM RTC [Normal / 0xE001] CM NVRAM [Normal / 0xE001] CM FPGA [Normal / 0xE001] CM LAN Port#0 [Normal / 0xE001] CM LAN Port#1 [Normal / 0xE001] CM LAN Port#2 [Normal / 0xE001] DI#0 Port#0 [Normal / 0xE001] DI#0 Port#1 [Normal / 0xE001] DI#1 Port#0 [Undefined / 0x0000] DI#1 Port#1 [Undefined / 0x0000] SATA SSD Controller Information Status/Status Code [Undefined / 0x0000] Active EC [EC#1] Next EC [EC#2] Firmware Version [V10L10-0000] SCU [Normal / 0xE001] SCU Voltage [10.80V] CM#0 CA#0 Port#0 Information Port Type [FC] Port Mode [CA] Status/Status Code [Normal / 0xE001] CA Active EC [EC#0] CA Next EC [EC#0] Connection [Loop] Loop ID [0x00] Transfer Rate [Auto Negotiation] Link Status [Unknown] Port WWN [500000E0D1000000] Node WWN [500000E0D1000000] Host Affinity [Disable] Host Response [0] SFP Type [ShortWave] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [40.11C] [-15.00C/100.00C] [-30.00C/128.00C] Voltage [4.24V] [3.00V/5.00V] [2.00V/7.00V] Current [10.25mA] [5.00mA/12.00mA] [2.00mA/15.00mA] TX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] RX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] CM#0 CA#0 Port#1 Information Port Type [FC] Port Mode [CA] Status/Status Code [Normal / 0xE001] CA Active EC [EC#0] CA Next EC [EC#0] Connection [Loop] Loop ID [0x00] Transfer Rate [Auto Negotiation] Link Status [Unknown] Port WWN [500000E0D1000000] Node WWN [500000E0D1000000] Host Affinity [Disable] Host Response [0] SFP Type [ShortWave] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [40.11C] [-15.00C/100.00C] [-30.00C/128.00C] Voltage [4.24V] [3.00V/5.00V] [2.00V/7.00V] Current [10.25mA] [5.00mA/12.00mA] [2.00mA/15.00mA] TX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] RX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW]

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 55 CM#0 PFM#0 Information Type [HHHL] Status/Status Code [Normal / 0xE001] Health [0%] Capacity [700GB] Parts Number [] Serial Number [] Hard Revision [] CM#0 PFM#1 Information Type [HHHL] Status/Status Code [Normal / 0xE001] Health [50%] Capacity [700GB] Parts Number [] Serial Number [] Hard Revision [] BCU/BTU Information BCU#0 Status/Status Code [Normal / 0xE001] BTU#0 Status/Status Code [Normal / 0xE001] BCU#0 ChargeRate [0%] BCU#0 Expires [0-00] BCU#0 Parts Number [] BCU#0 Serial Number [] BCU#0 Hard Revision [] BCU#1 Status/Status Code [Normal / 0xE001] BTU#1 Status/Status Code [Normal / 0xE001] BCU#1 ChargeRate [0%] BCU#1 Expires [0-00] BCU#1 Parts Number [] BCU#1 Serial Number [] BCU#1 Hard Revision [] BCU#2 Status/Status Code [Normal / 0xE001] BTU#2 Status/Status Code [Normal / 0xE001] BCU#2 ChargeRate [0%] BCU#2 Expires [0-00] BCU#2 Parts Number [] BCU#2 Serial Number [] BCU#2 Hard Revision [] SCCI#0 Information Status/Status Code [Normal / 0xE001] SCCI#1 Information Status/Status Code [Normal / 0xE001] For SAS, iSCSI, and FCoE, outputs differ from an FC host interface output at the "CM#x CA#x Port#x Information" level. For SAS information, the following information is displayed: CM#0 CA#0 Port#0 Information Port Type [SAS] Port Mode [CA] Status/Status Code [Normal / 0xE001] CA Active EC [EC#0] CA Next EC [EC#0] Transfer Rate [Auto Negotiation] Link Status PHY#0[Link Down ] PHY#1[Link Down ] PHY#2[Link Down ] PHY#3[Link Down ] Port WWN [500000E0D1000011] Node WWN [500000E0D1000000] Host Affinity [Disable] Host Response [3] CM#0 CA#0 Port#1 Information Port Type [SAS] Port Mode [CA] Status/Status Code [Normal / 0xE001] CA Active EC [EC#0] CA Next EC [EC#0] Transfer Rate [Auto Negotiation] Link Status PHY#0[Link Down ] PHY#1[Link Down ] PHY#2[Link Down ] PHY#3[Link Down ] Port WWN [500000E0D1000011] Node WWN [500000E0D1000000] Host Affinity [Disable] Host Response [3]

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 56 For iSCSI information, the following information is displayed: CM#0 CA#0 Port#0 Information Port Type [iSCSI] Port Mode [CA] Status/Status Code [Normal / 0xE001] Multi IP Address [Enable] Number of IP Address [16] CA Active EC [EC#0] CA Next EC [EC#0] Transfer Rate [1Gbps/Auto] Link Status [Link Down] iSCSI Name [iqn.2000-09.com.fujitsu:storage-system.eternus-dxl:00000000] iSCSI Alias Name [] Host Affinity [Disable] Host Response [0] iSNS Server Port No [0x0000] TCP Port No [0x0000] TCP Window Size [0x00] VLAN ID [-] Header Digest [OFF] Data Digest [OFF] Bandwidth Limit [-] Target Portal Group No [0x0000] CmdSN Count [Unlimited] Err Recovery Lvl [0x00] Task Retain Time [-] Reconnection Wait Time [-] SFP Type [SFP+] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [40.11C] [-15.00C/100.00C] [-30.00C/128.00C] Voltage [4.24V] [3.00V/5.00V] [2.00V/7.00V] Current [10.25mA] [5.00mA/12.00mA] [2.00mA/15.00mA] TX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] RX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] CM#0 CA#0 Port#1 Information Port Type [iSCSI] Port Mode [CA] Status/Status Code [Normal / 0xE001] Multi IP Address [Disable] Number of IP Address [1] CA Active EC [EC#0] CA Next EC [EC#0] Transfer Rate [1Gbps/Auto] Link Status [Link Down] iSCSI Name [iqn.2000-09.com.fujitsu:storage-system.eternus-dxl:00000000] iSCSI Alias Name [] Host Affinity [Disable] Host Response [0] iSNS Server Port No [0x0000] TCP Port No [0x0000] TCP Window Size [0x00] VLAN ID [-] Header Digest [OFF] Data Digest [OFF] Bandwidth Limit [-] Target Portal Group No [0x0000] CmdSN Count [Unlimited] Err Recovery Lvl [0x00] Task Retain Time [-] Reconnection Wait Time [-] SFP Type [SFP+] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [40.11C] [-15.00C/100.00C] [-30.00C/128.00C] Voltage [4.24V] [3.00V/5.00V] [2.00V/7.00V] Current [10.25mA] [5.00mA/12.00mA] [2.00mA/15.00mA] TX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] RX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW]

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 57 For FCoE information, the following information is displayed: CM#0 CA#0 Port#0 Information Port Type [FCoE] Status/Status Code [Normal / 0xE001] CA Active EC [EC#0] CA Next EC [EC#0] Transfer Rate [10Gbps] Link Status [Unknown] Port WWN [500000E0D1000010] Node WWN [500000E0D1000000] Host Affinity [-] Host Response [-] FC Frame Size [Unknown] VLAN ID [0x0000] Fabric Name [-] CM#0 CA#0 Port#1 Information Port Type [FCoE] Status/Status Code [Normal / 0xE001] CA Active EC [EC#0] CA Next EC [EC#0] Transfer Rate [10Gbps] Link Status [Unknown] Port WWN [500000E0D1000010] Node WWN [500000E0D1000000] Host Affinity [-] Host Response [-] FC Frame Size [Unknown] VLAN ID [0x0000] Fabric Name [-] SFP Type [SFP+] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [40.11C] [-15.00C/100.00C] [-30.00C/128.00C] Voltage [4.24V] [3.00V/5.00V] [2.00V/7.00V] Current [10.25mA] [5.00mA/12.00mA] [2.00mA/15.00mA] TX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] RX Power [1.35mW] [0.50mW/1.50mW] [0.00mW/1.80mW] For NAS information, the following information is displayed: CM#0 CA#0 Port#0 Information Port Type [NAS] Status/Status Code [Normal / 0xE001] CA Active EC [EC#1] CA Next EC [EC#2] MAC Address [00-16-E6-10-84-64] SFP Type [SFP+ Copper] SFP Information Present Warning(Low/High) Alarm(Low/High) Temperature [-] [-/-] [-/-] Voltage [-] [-/-] [-/-] Current [-] [-/-] [-/-] TX Power [-] [-/-] [-/-] RX Power [-] [-/-] [-/-] For SCU Information, the following information is displayed: SCU Information SCU#0 Status/Status Code [Normal / 0xE001] SCU#0 Voltage [9.40V] SCU#0 Expires [0-00] SCU#0 Parts Number [] SCU#0 Serial Number [] SCU#0 Hard Revision [] SCU#1 Status/Status Code [Normal / 0xE001] SCU#1 Voltage [9.40V] SCU#1 Expires [0-00] SCU#1 Parts Number [] SCU#1 Serial Number [] SCU#1 Hard Revision []

2.1 Storage System Status > show fru-ce ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 58 The following example displays the status of PSU#0: CLI> show fru-ce -type psu0 CE PSU#0 Information Status/Status Code [Normal / 0xE001]

2.1 Storage System Status > show fru-de ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 59 show fru-de This command displays the status of the components (Field Replaceable Units) in the drive enclosures. ■ Syntax ■ Parameter ■ Output show fru-de [-de enclosure_number] [-type {iom0|iom1|fem0|fem1|psu0|psu1|psu2|psu3}] -de Optional. This parameter specifies the drive enclosure number. Only one parameter can be specified. For details, refer to "1.2.3 Drive Enclosure Syntax" (page 22). If this parameter is omitted, all of the connected drive enclosures are displayed. Example: -de 1 (Only the drive enclosure #1) -type Optional. This parameter specifies the target component (FRU) name. The sub components embedded in a drive enclosure will also be displayed. Only one parameter can be specified. If this parameter is omitted, all of the FRUs are displayed. iom0 Details and status of the I/O module #0 iom1 Details and status of the I/O module #1 fem0 Details and status of the Fan Expander Module #0 (only for high-density drive enclosures) fem1 Details and status of the Fan Expander Module #1 (only for high-density drive enclosures) psu0 Details and status of the Power Supply Unit #0 psu1 Details and status of the Power Supply Unit #1 psu2 Details and status of the Power Supply Unit #2 (only for high-density drive enclo- sures) psu3 Details and status of the Power Supply Unit #3 (only for high-density drive enclo- sures) The following table shows the output information for the IOM. DE#n IOM#m Information (n: The drive enclosure number, m: The IOM number) Status/Status Code IOM#n status and the status code Error Code Error code to identify error events that have occurred in an expander. This information is only displayed when the Status is not "Normal" or "Undefined". WWN World Wide Name (For FEM#1, a hyphen (-) is shown.)

2.1 Storage System Status > show fru-de ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 60 Active EC EC number of the active firmware (current operating firmware) Next EC EC number of the stand-by firmware (the generation number of the firmware after the next power cycle) Firmware Version Version of the active firmware (current operating firmware) DE#n IOM#m Internal Parts Status/Status Code (n: The drive enclosure number, m: The IOM number) SAS Cable (IOM Port) #0(IN) SAS Cable #0(IN)(IOM port #0) status and the status code Error Code Error code to identify error events that have occurred in port#0. This information is only displayed when the Status is not "Normal" or "Undefined". SAS Cable (IOM Port) #1(OUT) SAS Cable #1(OUT)(IOM port #1) status and the status code Error Code Error code to identify error events that have occurred in port#1. IOM FEM Port#0 IOM FEM port#0 status and the status code (only for high-density drive enclosures) The connection destination of this port is the FEM#1 EXP#0 port. Error Code Error code to identify error events that have occurred in port#0 (only for high-density drive enclosures). IOM FEM Port#1 IOM FEM port#1 status and the status code (only for high-density drive enclosures) The connection destination of this port is the FEM#1 EXP#1 port. Error Code Error code to identify error events that have occurred in port#1 (only for high-density drive enclosures). The following table shows the output information for the Fan Expander Modules. DE#n FEM#m Information (n: The drive enclosure number, m: The FEM number) (Information on FEM#1 appears regardless of the number of controllers) Status/Status Code FEM (FEM#n) status and the status code Error Code Error code to identify error events that occurred in a Fan Expander Module. This information is only displayed when the Status is not "Normal" or "Undefined".

2.1 Storage System Status > show fru-de ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 61 DE#n FEM#m Internal Parts Status/Status Code (n: The drive enclosure number, m: The FEM number) (Information on FEM#1 appears regardless of the number of controller modules) FEM EXP#0 Port FEM (EXP#0) status and the status code Error Code Error code to identify error events that occurred in port#0. This information is only displayed when the Status is not "Normal" or "Undefined". FEM EXP#1 Port FEM (EXP#1) status and the status code Error Code Error code to identify error events that occurred in port#1. This information is only displayed when the Status is not "Normal" or "Undefined". DE#n FEM#m EXP#l Information (n: The drive enclosure number, m: The FEM number, I: The EXP num- ber) (Information on FEM#1 appears regardless of the number of controller modules) Status/Status Code EXP (EXP#l) status and the status code Error Code Error code to identify error events that have occurred in an expander in the Fan Expander Module. This information is only displayed when the Status is not "Normal" or "Undefined". WWN World Wide Name Active EC EC number of the active firmware (the current operating firmware) Next EC EC number of the stand-by firmware (the generation number of the firmware after the next power cycle) Firmware Version Version of the active firmware (the current operating firmware) The following table shows the output information for the power supply units. Status/Status Code Power supply unit (PSU#n) status and the status code Error Code Error code to identify error events that occurred in a power supply unit. This information is only displayed when the Status is not "Normal" or "Undefined".

2.1 Storage System Status > show fru-de ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 62 ■ Example(s) The following example displays the status of Expander #0 in drive enclosure #1: CLI> show fru-de -de 1 -type iom0 DE#1 IOM#0 Information Status/Status Code [Normal / 0xE001] WWN [500000E0D060C4FF] Active EC [EC#1] Next EC [EC#1] Firmware Version [V10L10-0000] DE#1 IOM#0 Internal Parts Status/Status Code SAS Cable(IOM Port)#0(IN) [Normal / 0xE001] SAS Cable(IOM Port)#1(OUT) [Normal / - ] The following example displays the status of Expander #0 in drive enclosure #1 (high-density drive enclo- sure): CLI> show fru-de -de 1 -type iom0 DE#1 IOM#0 Information Status/Status Code [Normal / 0xE001] WWN [500000E0D060C4FF] Active EC [EC#1] Next EC [EC#2] Firmware Version [V10L10-0000] DE#1 IOM#0 Internal Parts Status/Status Code SAS Cable(IOM Port)#0(IN) [Normal / 0xE001] SAS Cable(IOM Port)#1(OUT) [Normal / 0xE001] IOM FEM Port#0 [Normal / 0xE001] IOM FEM Port#1 [Normal / 0xE001] The following example displays the status of the Fan Expander Module in drive enclosure #1: CLI> show fru-de -de 1 -type fem0 DE#1 FEM#0 Information Status/Status Code [Normal / 0xE001] DE#1 FEM#0 Internal Parts Status/Status Code FEM EXP#0 Port [Normal / 0xE001] FEM EXP#1 Port [Normal / 0xE001] DE#1 FEM#0 EXP#0 Information Status/Status Code [Normal / 0xE001] WWN [500000E0D060C4FF] Active EC [EC#1] Next EC [EC#2] Firmware Version [V10L10-0000] DE#1 FEM#0 EXP#1 Information Status/Status Code [Normal / 0xE001] WWN [500000E0D060C4FF] Active EC [EC#1] Next EC [EC#2] Firmware Version [V10L10-0000] The following example displays the status of PSU#0 in drive enclosure #2: CLI> show fru-de -de 2 -type psu0 DE#2 PSU#0 Information Status/Status Code [Normal / 0xE001]

2.1 Storage System Status > show disks ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 63 show disks This command displays the details and status of the disk. As an option, an enclosure (all disks contained in the specified enclosure), specific disks, or all the undefined disks can be specified. ■ Syntax ■ Parameter ■ Output show disks [ -type {undefined | ce | de [-de enclosure_number]} | -disks {disks | all | productid} ] -type Optional. This parameter specifies which disk information will be displayed. This parameter cannot be specified with the "-disks" parameter. If all of the parameters are omitted, all disks registered in the system will be displayed. undefined undefined All the undefined disks ce All disks in the controller enclosure (only for the ETERNUS DX100 S3/DX200 S3 and the ETERNUS DX200F) de All disks in the specified drive enclosure When using this parameter, the "-de" parameter and the drive enclosure number must also be specified. -de Optional. This parameter specifies the number of the drive enclosure for which details are to be obtained. Only one parameter can be specified. For details, refer to "1.2.3 Drive Enclosure Syntax" (page 22) This parameter cannot be used for other category types. -disks Optional. This parameter specifies which disk number to display the detailed information of the disk for. One or more parameters can be specified. For details, refer to "1.2.4 Drive Syntax" (page 23) Specifying "all" will display the details of all disks. When using the "productid" parameter, the product ID list of all disks is displayed. This function is useful when updating disk firmware. all Details of all disks productid The Product ID list of all disks For summary, the following items are displayed. Location Disk slot number Status Disk status Size Disk capacity Type Disk type The size of the drive (2.5" or 3.5") is displayed. Speed Rotating speed (unit: rpm)

2.1 Storage System Status > show disks ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 64 Usage Disk usage Example: Data, Spare, etc. Health Remaining capacity (operating life) of the SSD (unit: %) For details, the following items are displayed. Location Disk slot number Status Disk status Error Code Error Code to identify error events that occurred in a disk. This information is only displayed when the Status is not "Available". Size Disk capacity Type Disk type The size of the drive (2.5" or 3.5") is displayed. Speed Rotating speed (unit: rpm) Usage Disk usage Example: Data, Spare, etc. Health Remaining capacity (operating life) of the SSD (unit: %) RAID Group RAID group to which this disk belongs Motor Status Disk motor status by ECO functions Rebuild/Copy back Progress Progress status of Rebuild and Copy back Vendor ID Vendor ID Product ID Product ID Serial Number Serial number WWN World Wide Name Firmware Revision Disk firmware version Total completed passes Total number of disk patrols Progress with current pass Progress rate of the current disk patrol

2.1 Storage System Status > show disks ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 65 ■ Example(s) Completed passes since last Power On Total number of disk patrols that were performed since the ETERNUS DX was last turned on For the product ID list, the following items are displayed: Product ID Product ID Revision Disk firmware version The following example displays a summary of all the disks: CLI> show disks Location Status Size Type Speed(rpm) Usage Health(%) ------------- ----------------------------- ------- --------------- ---------- ------------------- --------- CE-Disk#0 Available 4TB 3.5 SSD-H 7200 System 100 CE-Disk#1 Available 4TB 3.5 SSD-M 7200 System 0 CE-Disk#2 Available 4TB 3.5 SSD-L 7200 System 0 The following example displays a summary of all the disks in the controller enclosure: CLI> show disks -type ce Location Status Size Type Speed(rpm) Usage Health(%) ------------- ----------------------------- ------- --------------- ---------- ------------------- --------- CE-Disk#0 Available 4TB 3.5 Online 7200 System 100 CE-Disk#1 Available 4TB 3.5 Online 7200 System 100 CE-Disk#2 Available 4TB 3.5 Online 7200 Data 100 CE-Disk#3 Available(Predictive Failure) 4TB 3.5 Online 7200 Data 100 CE-Disk#4 Available 4TB 3.5 Online 7200 Data 100 CE-Disk#5 Available 4TB 3.5 Online 7200 Data 100 CE-Disk#6 Available 4TB 3.5 Online 7200 Data 100 CE-Disk#7 Available 4TB 3.5 Online 7200 Data 100 CE-Disk#8 Available 4TB 3.5 Online 7200 Data 100 CE-Disk#9 Available 4TB 3.5 Online 7200 Present 0 CE-Disk#10 Available 4TB 3.5 Online 7200 Global Hot Spare 0 CE-Disk#11 Available 4TB 3.5 Online 7200 Dedicated Hot Spare 0 The following example displays a summary of all the disks in drive enclosure #1: CLI> show disks -type de -de 1 Location Status Size Type Speed(rpm) Usage Health(%) ------------- ----------------------------- ------- --------------- ---------- ------------------- --------- DE#1-Disk#0 Available(Predictive Failure) 4TB 3.5 Online 7200 Data 100 DE#1-Disk#1 Available 4TB 3.5 Online 7200 Data 100 DE#1-Disk#2 Available 4TB 3.5 Online 7200 Data 100 DE#1-Disk#3 Available 4TB 3.5 Online 7200 Data 100 DE#1-Disk#4 - DE#1-Disk#5 Available 4TB 3.5 Online 7200 Data 100 DE#1-Disk#6 - DE#1-Disk#7 - DE#1-Disk#8 - DE#1-Disk#9 Available 4TB 3.5 Online 7200 Data 100 DE#1-Disk#10 Available 4TB 3.5 Online 7200 Global Hot Spare 0 DE#1-Disk#11 Available 4TB 3.5 Online 7200 Dedicated Hot Spare 0 The following example displays a summary of all the undefined disks: CLI> show disks -type undefined Location Status Size Type Speed(rpm) Usage Health(%) ------------- ----------------------------- ------- --------------- ---------- ------------------- --------- DE#4-Disk#0 Available 4TB 3.5 Online 7200 Data 100 DE#4-Disk#1 Available 4TB 3.5 Online 7200 Data 100 DE#5-Disk#1 Available 4TB 3.5 Online 7200 Data 100 DE#6-Disk#11 Available(Predictive Failure) 4TB 3.5 Online 7200 Data 100

2.1 Storage System Status > show disks ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 66 The following example displays the details of disk #100 (disk #00 in drive enclosure #1): CLI> show disks -disks 100 Drive Enclosure #1 Disk #0 Information Location [DE#1-Disk#0] Status [Error](Error Code : 0x0010) Size [4TB] Type [3.5 Online] Speed [7200rpm] Usage [Data] Health [100%] RAID Group [1000 : RGP001] Motor Status [Active] Rebuild/Copyback Progress [-] Vendor ID [FUJITSU] Product ID [FT373207C-K] Serial Number [1234567890] WWN [1111111111111111] Firmware Revision [12CD] Total completed passes [64565Cycle] Progress with current pass [79%] Completed passes since last Power On [30737Cycle] The following example displays the product ID list: CLI> show disks -disks productid Product ID Revision ---------------- -------- ST373455SS 12CD ST99999999 3456

2.1 Storage System Status > show hardware-information ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 67 show hardware-information This command displays the hardware information for each enclosure and sub-component. ■ Syntax ■ Parameter No parameters. ■ Output show hardware-information For each enclosure, the following items are displayed. All possible drive enclosures are displayed, irrespective of whether or not they are currently installed. Drive enclosures that do not exist are indicated by hyphens. Serial No. Serial number embedded in the enclosure Other Information Individual identifier embedded in the controlling Fujitsu enclosure. For each component, the following items are displayed. For single controller models, both controller module #1 and expander module #1 are indicated by hyphens. Information is not displayed for drive enclosures that do not exist. Part No. Part number embedded in the component Serial No. Serial number embedded in the component Version Hardware revision of the component For each component, the following items are displayed. For single controller models, both BRT#1 and QSFP#1 are indicated by hyphens. Information is not displayed for BRT that do not exist. Part No. Part number embedded in the component Serial No. Serial number embedded in the component Vendor Name Vendor Name embedded in the component

2.1 Storage System Status > show hardware-information ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 68 ■ Example(s) The following hardware information is displayed: CLI> show hardware-information Enclosure Serial No. Other Information Controller Enclosure ST35CE000012 35CE000012 Drive Enclosure#1 ST35DE000009 35DE000009 Drive Enclosure#2 ST35DE000011 35DE000011 Drive Enclosure#3 ST35DE000019 35DE000019 Drive Enclosure#4 ST35DE000018 35DE000018 Drive Enclosure#5 ST35DE000023 35DE000023 Drive Enclosure#6 - - Drive Enclosure#7 - - Drive Enclosure#8 - - Drive Enclosure#9 - - Component Part No. Serial No. Version CM#0 CA07111-C631 PP09280285 AA CM#1 CA07111-C631 PP0928028A AA CM#0-PFM#0 CA07111-C662 PP085102T0 06B CM#0-PFM#1 CA07111-C662 PP085102T0 06B CM#1-PFM#0 - - - CM#1-PFM#1 - - - PSU#0 CA05954-0860 FA09060095 06A PSU#1 CA05954-0860 FA09060088 06A DE#1-IOM#0 CA07111-C661 PP085100Z7 AA DE#1-IOM#1 CA07111-C661 PP085100YT AA DE#1-PSU#0 CA05954-0860 FA09030006 05A DE#1-PSU#1 CA05954-0860 FA08520078 05A DE#2-IOM#0 CA07111-C661 PP085100YP AA DE#2-IOM#1 CA07111-C661 PP085100YW AA DE#2-PSU#0 CA05954-0860 FA08520085 05A DE#2-PSU#1 CA05954-0860 FA08520084 05A DE#3-IOM#0 CA07111-C661 PP085100Z9 AA DE#3-IOM#1 CA07111-C661 PP085100ZD AA DE#3-PSU#0 CA05954-0860 FA09050024 06A DE#3-PSU#1 CA05954-0860 FA09050025 06A DE#4-IOM#0 CA07111-C661 PP085100Z0 AA DE#4-IOM#1 CA07111-C661 PP085100YZ AA DE#4-PSU#0 CA05954-0860 FA09040009 06A DE#4-PSU#1 CA05954-0860 FA09040011 06A DE#5-IOM#0 CA07111-C661 PP085102T0 AA DE#5-IOM#1 CA07111-C661 PP085102T1 AA DE#5-FEM#0 CA07112-C661 PP085100YQ AA DE#5-FEM#1 CA07112-C661 PP085100YX AA DE#5-PSU#0 CA05954-0860 FA09060036 06A DE#5-PSU#1 CA05954-0860 FA09060038 06A DE#5-PSU#2 CA05954-0862 FA08520087 05A DE#5-PSU#3 CA05954-0863 FA08520088 05A

Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 69 Chapter 3 Configuration Settings and Display This chapter explains the commands used for basic settings of the storage system. These settings include RAID group management, volume management, Thin Provisioning Pool management, Flexible Tier management, and host interface management. 3.1 RAID Group Management This chapter explains the commands used for the following settings: • RAID group settings • Hot spares settings • Eco-mode settings 3.1.1 RAID Group This section explains the commands used for RAID group management. All disks contained in a RAID group must be the same disk type. The functions to control RAID groups are as follows: • Creating a RAID group • Deleting RAID groups • Changing an existing RAID group • LDE, Logical Device Expanding (expanding a RAID group)

3.1 RAID Group Management > show raid-groups ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 70 show raid-groups This command displays a summary list of all the RAID groups or the details of a specified RAID group(s). ■ Syntax ■ Parameter ■ Output show raid-groups [-rg-number rg_numbers | -rg-name rg_names ] -rg-number or -rg-name Optional. This parameter specifies RAID group identifiers. One or more RAID groups can be specified. For details, refer to "1.2.9 RAID Group Syntax" (page 25). If the RAID group identifier is omitted, a summary list of all the RAID groups is displayed. rg_numbers RAID group number rg_names RAID group name RAID Group RAID group identifiers No. RAID group number Name RAID group name RAID Level RAID level Consist of Fast Recovery Disks configured for the Fast Recovery RAID Group. (This information is displayed for RAID groups with RAID6-FR RAID level. A hyphen (-) is dis- played for other RAID levels.) The disk configuration, the number of configurations, and the number of HS disks for RAID6 are displayed. Example: (3D+2P)x2+1HS Assigned CM Assigned CM number (CM number to control a RAID group) Status RAID group status Total Capacity (MB) Total capacity (Unit: MB) Free Capacity (MB) Free capacity (Unit: MB) Stripe Depth (Unit: KB) Stripe Depth (Unit: KB) (Only when viewing details) Key Group Usage status of the key group (Only when viewing details)

3.1 RAID Group Management > show raid-groups ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 71 ■ Example(s) Disk List List of drives that belong to a RAID group (only when viewing details) Disk Location of the disks that belong to a RAID group Status Status of the disks that belong to a RAID group Usage Usage of the disks that belong to a RAID group Mirroring Pair disk information in case of RAID1 or RAID1+0 Fast Recovery Disk When the RAID Level is RAID6-FR, if the HS area is being used, the drive that failed is dis- played. The following example displays a summary list of all the disks registered in the system: CLI> show raid-groups RAID Group RAID Assigned Status Total Free No. Name Level CM Capacity(MB) Capacity(MB) --- ---------------- -------- --------- ------------------------------- ------------ ------------ 1 RAIDGROUP001 RAID1+0 CM#0 Spare in Use 134656 132535 2 RAIDGROUP002 RAID5 CM#1 Available 134656 132532 3 RAIDGROUP003 RAID5 CM#1 SED Locked 134656 132532 The following example displays details of the RAID5(4+1) RAID group named "R1". In this example, two disks have failed and two hot spares are in use. These hot spare disks have also failed. When multiple disks fail, the disk in "Failed Usable" status indicates the last disk that has failed: CLI>show raid-groups -rg-name R1 RAID Group RAID Consist of Assigned Status Total Free Stripe Key Fast Recovery No. Name Level Fast Recovery CM Capacity(MB) Capacity(MB) Depth(KB) Group Disk --- ---------------- -------- -------------- --------- ------------------------------- ------------ ------------ --------- ------- ------------- 0 R1 RAID5 - CM#0 Broken 1116160 1116136 64 Enable - Disk Status Usage Mirroring -------------- ----------------------------- ------------------- -------------- CE-Disk#0 Available Data CE-Disk#1 Available Data CE-Disk#2 Available Data CE-Disk#3 Broken Data CE-Disk#4 Broken Data CE-Disk#5 Broken Dedicated Hot Spare CE-Disk#6 Failed Usable Global Hot Spare The following example displays the details of RAID group #0. When the RAID level is RAID1 or RAID1+0, the mirroring information is also displayed: CLI> show raid-groups -rg-number 0 RAID Group RAID Consist of Assigned Status Total Free Stripe Key Fast Recovery No. Name Level Fast Recovery CM Capacity(MB) Capacity(MB) Depth(KB) Group Disk --- ---------------- -------- -------------- --------- ------------------------------- ------------ ------------ --------- ------- ------------- 0 RAIDGROUP1 RAID1+0 - CM#0 Spare in Use 560128 60104 64 Disable - Disk Status Usage Mirroring -------------- ----------------------------- ------------------- -------------- CE-Disk#2 Broken Data - CE-Disk#3 Available Data CE-Disk#5 CE-Disk#4 Available Data CE-Disk#7 CE-Disk#5 Available Data CE-Disk#3 CE-Disk#7 Available Global Hot Spare CE-Disk#4

3.1 RAID Group Management > show raid-groups ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 72 The following example displays the details of RAID Group #0 when the RAID level is RAID6-FR: CLI> show raid-groups -rg-number 0 RAID Group RAID Consist of Assigned Status Total Free Stripe Key Fast Recovery No. Name Level Fast Recovery CM Capacity(MB) Capacity(MB) Depth(KB) Group Disk --- ---------------- -------- -------------- --------- ------------------------------- ------------ ------------ --------- ------- ------------- 0 R1 RAID6-FR (3D+2P)x2+1HS CM#0 Broken 1116160 1116136 64 Enable DE#01-Disk#5 Disk Status Usage Mirroring -------------- ----------------------------- ------------------- -------------- DE#01-Disk#0 Available Data DE#01-Disk#1 Available Data DE#01-Disk#2 Available Data DE#01-Disk#3 Available Data DE#01-Disk#4 Available Data DE#01-Disk#5 Broken Data DE#01-Disk#6 Available Data DE#01-Disk#7 Available Data DE#01-Disk#8 Available Data DE#01-Disk#9 Available Data DE#01-Disk#10 Available Data

3.1 RAID Group Management > show raid-group-progress ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 73 show raid-group-progress This command displays the progress of the Rebuild/Copyback process and the expansion process of all RAID groups (Logical Device Expansion). Individual RAID groups can also be specified. ■ Syntax ■ Parameter ■ Output show raid-group-progress [-rg-number rg_numbers | -rg-name rg_names ] -rg-number or -rg-name Optional. This parameter specifies RAID group identifiers. If the RAID group identifier is omitted, a progress list of all the RAID groups is displayed. For details, refer to "1.2.9 RAID Group Syntax" (page 25). rg_numbers RAID group number rg_names RAID group name RAID Group RAID group identifiers No. RAID group number Name RAID group name Status RAID group status Rebuild/Copyback Information on the recovery progress Progress Progress (0 – 100%) Estimated time left Estimated remaining recovery time - Formatting is not performed or is complete. calculating The remaining time is being calculated. 30days or more The remaining time is 30 days or more. Xday Yh Zmin The remaining time is less than 30 days but 1 day or more. Yh Zmin The remaining time is less than 1 day but 1 hour or more. Zmin The remaining time is less than 1 hour but 1 minute or more. Less than 1min The remaining time is less than 1 minute.

3.1 RAID Group Management > show raid-group-progress ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 74 ■ Example(s) Remaining size Remaining capacity of recovery - Formatting is not performed or is complete. XMB Remaining capacity (rounded up to the nearest whole number) X: decimal number Expanding Progress Progress status of expanding RAID groups (Logical Device Expansion) The following example displays a progress list of all the RAID groups: CLI> show raid-group-progress RAID Group Status Rebuild/Copyback Expanding No. Name Progress Estimated time left Remaining size Progress --- ---------------- ------------------------------- -------- ------------------- -------------- --------- 0 RAIDGROUP001 Copyback 87% 12h 59min 1024MB - 1 RAIDGROUP012 Available - - - 19% 2 RAIDGROUP013 Available 87% Less than 1min 16MB - 3 RAIDGROUP014 SED Locked 0% 30days or more 134217728MB - The following example displays only the progress status of the RAID group #1: CLI> show raid-group-progress -rg-number 1 RAID Group Status Rebuild/Copyback Expanding No. Name Progress Estimated time left Remaining size Progress --- ---------------- ------------------------------- -------- ------------------- -------------- --------- 1 RAIDGROUP012 Available - - - 19% The following example displays the progress status of the RAID group named "RAIDGROUP001" and "RAIDGROUP012": CLI> show raid-group-progress -rg-name RAIDGROUP001,RAIDGROUP012 RAID Group Status Rebuild/Copyback Expanding No. Name Progress Estimated time left Remaining size Progress --- ---------------- ------------------------------- -------- ------------------- -------------- --------- 0 RAIDGROUP001 Copyback 87% 12h 59min 1024MB - 1 RAIDGROUP012 Available - - - 19%

3.1 RAID Group Management > create raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 75 create raid-group This command creates a RAID group with the specified RAID group name, RAID level and disks. When registering a hot spare, refer to the "set global-spare" or the "set dedicated-spare" command. ■ Syntax ■ Parameter create raid-group -name alias_name -disks disks -level {0|1|5|6|10|50|6fr} [-assigned-cm {0|1|auto}] [-stripe-depth { 64kb | 128kb | 256kb | 512kb | 1024kb }] [-fr-consist { (3D+2P)x2+1HS | (6D+2P)x2+1HS | (9D+2P)x2+1HS | (12D+2P)x2+1HS | (5D+2P)x4+1HS | (13D+2P)x2+1HS | (3D+2P)x6+1HS }] -name This parameter specifies the alias name of a RAID group. Only one name can be specified. For details, refer to "1.2.5 Alias Name Syntax" (page 23). alias_name RAID group name -disks This parameter specifies which disks will form the RAID group. For details, refer to "1.2.4 Drive Syntax" (page 23). disks Drive -level This parameter specifies the RAID level. 0 RAID0 1 RAID1 5 RAID5 6 RAID6 10 RAID1+0 50 RAID5+0 6fr RAID6-FR (Fast Recovery) -assigned-cm Optional. This parameter specifies the assigned controller (CM number) of the specified RAID group. If "auto" is specified, the fixed controller, which is calculated automatically by the system, is assigned. If this parameter is omitted, the "auto" mode is set. 0 Controller module#0 1 Controller module#1 auto Automatically (default)

3.1 RAID Group Management > create raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 76 ■ Example(s) -stripe-depth Optional. This parameter specifies the stripe depth for the RAID group that is to be created. If omitted, then it is handled as if "64kb" is selected. The available values vary depending on the RAID level and the number of drives. 64kb 64KB 128kb 128KB (Only for RAID 5 configurations of 10 or more disks, RAID 0 configurations, and RAID1+0 configurations) 256kb 256KB (Only for RAID 5 configurations of 9 or less disks, RAID 0 configurations, and RAID1+0 configurations) 512kb 512KB (Only for RAID 5 configurations of 5 or less disks, RAID 0 configurations, and RAID1+0 configurations) 1024kb 1024KB (Only for RAID0 configurations and RAID1+0 configurations) -fr-consist Optional. This parameter specifies the disks that consist of the Fast Recovery RAID group. In the case of RAID6-FR configurations, this parameter must be specified. (3D+2P)x2+1HS RAID6(3+2)×2, HS×1 (6D+2P)x2+1HS RAID6(6+2)×2, HS×1 (9D+2P)x2+1HS RAID6(9+2)×2, HS×1 (12D+2P)x2+1HS RAID6(12+2)×2, HS×1 (5D+2P)x4+1HS RAID6(5+2)×4, HS×1 (13D+2P)x2+1HS RAID6(13+2)×2, HS×1 (3D+2P)x6+1HS RAID6(3+2)×6, HS×1 The following example creates a RAID group named "RGP001". RAID1 level is assigned using disks #003 and #004: CLI> create raid-group -name RGP001 -level 1 -disks 003,004

3.1 RAID Group Management > set raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 77 set raid-group This command changes the information of an existing RAID group. ■ Syntax ■ Parameter set raid-group {-rg-number rg_number | -rg-name rg_name } [-name name] [-assigned-cm {0|1|auto}] [-key-group {enable|disable}] -rg-number or -rg-name This parameter specifies RAID group identifiers. Only one RAID group identifier can be specified when changing a RAID group alias name. One or more RAID group identifiers can be specified when changing the assigned CM. For details, refer to "1.2.9 RAID Group Syntax" (page 25). rg_number RAID group number rg_name RAID group name -name Optional. This parameter specifies the new RAID group name. If this parameter is omitted, the name is not changed. For details, refer to "1.2.5 Alias Name Syntax" (page 23). name RAID group name -assigned-cm Optional. This parameter specifies the assigned controller module number of the RAID group. If "auto" is specified, the fixed controller, which is calculated automatically by the system, is assigned. If this parameter is omitted, the assigned CM is not changed. 0 Controller module#0 1 Controller module#1 auto Automatically (default) -key-group Optional. This parameter specifies whether to use the key group. If omitted, the existing setting is not changed. enable The key group is used (the SED authentication key that is managed by the key server is used). disable The key group is not used (the common key in the ETERNUS DX is used).

3.1 RAID Group Management > set raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 78 ■ Example(s) The following example changes the RAID group named "RGP001". The new name is "RAID002": CLI> set raid-group -rg-name RGP001 -name RAID002 The following example changes the CM number that is associated with the RAID group named "RGP001". The new CM number is "CM#1": CLI> set raid-group -rg-name RGP001 -assigned-cm 1 The following example changes the CM number that is associated with RAID groups #2 and #4. The new CM number is "CM#1": CLI> set raid-group -rg-number 2,4 -assigned-cm 1 The following example sets a key group for RAID groups #2 and #4: CLI> set raid-group -rg-number 2,4 -key-group enable

3.1 RAID Group Management > delete raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 79 delete raid-group This command deletes an existing RAID group(s). A RAID group cannot be deleted if one or more volumes exist in the RAID group. ■ Syntax ■ Parameter ■ Example(s) • RAID groups cannot be deleted until the expansion process is complete. • All volumes in a specified RAID group must be deleted before the RAID group is deleted. delete raid-group {-rg-number rg_numbers | -rg-name rg_names } -rg-number or -rg-name This parameter specifies RAID group identifiers. One or more RAID group identifiers can be specified. For details, refer to "1.2.9 RAID Group Syntax" (page 25). rg_numbers RAID group number rg_names RAID group name The following example deletes the RAID group named "R1": CLI> delete raid-group -rg-name R1 The following example deletes consecutive RAID groups #1 - #8: CLI> delete raid-group -rg-number 1-8

3.1 RAID Group Management > expand raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 80 expand raid-group This command expands a RAID group (Logical Device Expansion). The capacity of an existing RAID group is expanded by adding new disks to the RAID group. A new RAID level can also be specified. Any volumes in the existing RAID group are relocated to the new RAID group. ■ Syntax ■ Parameter • RAID5+0 is not supported, not even for pure capacity expansion operations. • Expanding a RAID level other than RAID0 to RAID0 is not supported. • When RAID group capacity is expanded without changing the RAID level, specify only the new disks to be added for the "-disks" parameter. • If the RAID level is changed with RAID group expansion, at least one disk that is already configured in an expansion source RAID group and all the new disks that are to be added must be specified for the '-disks' parameter. expand raid-group {-rg-number rg_number | -rg-name rg_name } -disks disks [-level {0|5|6|10}] [-name name] -rg-number or -rg-name This parameter specifies a RAID group identifier. Only one RAID group identifier can be specified. For details, refer to "1.2.9 RAID Group Syntax" (page 25). rg_number RAID group number rg_name RAID group name -disks This parameter specifies the disks to add to a RAID group. One or more parameters can be specified. This parameter specifies the disk numbers for the disks that configure the RAID group before expansion and the numbers for the disks that are to be added. For details, refer to "1.2.4 Drive Syntax" (page 23). disks Drive -level Optional. This parameter specifies the new RAID level of the expanded RAID group. RAID5+0 level is not supported. 0 RAID0 5 RAID5 6 RAID6 10 RAID1+0 -name Optional. This parameter specifies the new RAID group name to be used for the expanded RAID group. For details, refer to "1.2.5 Alias Name Syntax" (page 23). names RAID group name

3.1 RAID Group Management > expand raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 81 ■ Example(s) The following example expands the RAID group named "RGP001" using six disks, and changes the RAID level to RAID5: CLI> expand raid-group -rg-name RGP001 -disks 101-103,201-203 -level 5

3.1 RAID Group Management ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 82 3.1.2 Hot Spares This section explains the commands that are related to hot spares. There are two types of hot spares: • Global Hot Spare (Global HS) A hot spare that can be used by all RAID groups (except RAID0) • Dedicated Hot Spare (Dedicated HS/DHS) A hot spare that can be used by one specific RAID group Hot spares must be of the same disk type and must have the same (or larger) capacity as the disks in the assigned RAID group. A list of registered hot spare disks can be displayed by using the "show disks" command.

3.1 RAID Group Management > set global-spare ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 83 set global-spare This command assigns a disk as a Global Hot Spare. A Global Hot Spare is used as a substitute for a disk that has failed in a RAID group. A Global Hot Spare is shared by all of the existing RAID groups (except for RAID0 level). A list of registered hot spare disks can be displayed by using the "show disks" command. ■ Syntax ■ Parameter ■ Example(s) set global-spare -disks disks -disks This parameter specifies the disks to be registered as Global Hot Spares. One or more disks can be specified. For details, refer to "1.2.4 Drive Syntax" (page 23). disks Drive The following example registers disks #101 and #102 as Global Hot Spares: CLI> set global-spare -disks 101,102 In the following example, disks #101 and #102 are assigned as Global Hot Spares and disk #103 is then added to the available Global Hot Spare pool. Adding additional Global Hot Spares does not remove any hot spares that are previously set: CLI> set global-spare -disks 101,102 CLI> set global-spare -disks 103

3.1 RAID Group Management > release global-spare ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 84 release global-spare This command releases Global Hot Spare(s). The disk will then have an unassigned (present) status. ■ Syntax ■ Syntax ■ Example(s) release global-spare -disks disks -disks This parameter specifies the disks to be released from the Global Hot Spare. One or more disks can be specified. For details, refer to "1.2.4 Drive Syntax" (page 23). disks Drive The following example releases disk #011 from the Global Hot Spares: CLI> release global-spare -disks 011 The following example releases disks #101 to #105 from the Global Hot Spares: CLI> release global-spare -disks 101-105

3.1 RAID Group Management > set dedicated-spare ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 85 set dedicated-spare This command assigns a disk as a Dedicated Hot Spare. A Dedicated Hot Spare is used as a substitute for a disk that has failed in a specific RAID group. If there are no dedicated hot spares assigned (or available) to a RAID group, a global hot spare is used. A dedicated hot spare can only be assigned to a single RAID group. However, one RAID group can have one or more dedicated hot spares. ■ Syntax ■ Parameter ■ Example(s) set dedicated-spare -disks disks {-rg-number rg_numbers | -rg-name rg_names } -disks This parameter specifies the disks to be registered as Dedicated Hot Spares. One or more disks can be specified. If two or more parameters are specified, they must be specified in the same order as the associated RAID group identifier parameters. For details, refer to "1.2.4 Drive Syntax" (page 23). disks Drive -rg-number or -rg-name This parameter specifies the RAID group identifiers to which the Dedicated Hot Spares will be assigned. One or more RAID group identifiers can be specified. If two or more RAID group identifiers are specified, they must be specified in the same order as the associated disk parameters. For details, refer to "1.2.9 RAID Group Syntax" (page 25). rg_numbers RAID group number rg_names RAID group name The example assigns disk #110 as a dedicated hot spare to the RAID group "R1": CLI> set dedicated-spare -disks 110 -rg-name R1 The following example assigns disks #110 and #111 as dedicated hot spares to the RAID group named "RGP001": CLI> set dedicated-spare -disks 110,111 -rg-name RGP001 The following example assigns two different disks to two different RAID groups. Disk #110 is assigned as a Dedicated Hot Spare to the RAID group named "RGP1". Disk #111 is assigned as a Dedicated Hot Spare to the RAID group named "RGP2": CLI> set dedicated-spare -disks 110,111 -rg-name RGP1,RGP2

3.1 RAID Group Management > set dedicated-spare ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 86 The following example first assigns disk #101 as a Dedicated Hot Spare and then adds Disk #102 as a Dedicated Hot Spare to the same RAID group. Adding additional Dedicated Hot Spares does not remove any hot spares that are previously set: CLI> set dedicated-spare -disks 101 -rg-name RGP1 CLI> set dedicated-spare -disks 102 -rg-name RGP1

3.1 RAID Group Management > release dedicated-spare ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 87 release dedicated-spare This command releases a dedicated hot spare(s). The disk will then have an unassigned (present) status. ■ Syntax ■ Parameter ■ Example(s) release dedicated-spare -disks disks -disks This parameter specifies the disks that are registered as Dedicated Hot Spares. One or more disks can be specified. For details, refer to "1.2.4 Drive Syntax" (page 23). disks Drive The following example releases Dedicated Hot Spare #110: CLI> release dedicated-spare -disks 110 The following example releases Dedicated Hot Spares #110 and #111: CLI> release dedicated-spare -disks 110,111

3.1 RAID Group Management ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 88 3.1.3 Eco-mode Management This section explains the commands that are related to the Eco-mode functions. They are only applicable when the Eco-mode is enabled using the "set eco-mode" command. The three steps involved in enabling the Eco-mode functions are as follows: Procedure 1 Enable the Eco-mode. 2 Create an Eco-mode schedule. 3 Assign the Eco-mode schedule to RAID groups. End of procedure The commands described in this section are not supported in the ETERNUS DX200F.

3.1 RAID Group Management > show eco-mode ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 89 show eco-mode This command displays the current Eco-mode status and parameter settings. ■ Syntax ■ Parameter No parameters. ■ Output ■ Example(s) show eco-mode Mode Indicates whether the Eco-mode function is enabled. Host I/O Monitoring Time Monitoring interval time of the host I/O Disk Motor Control Limit Count Number of times that a disk motor will power off and on in one day The following example displays the current Eco-mode settings: CLI> show eco-mode Mode [Enable] Host I/O Monitoring Time [60 min.] Disk Motor Control Limit Count [5]

3.1 RAID Group Management > set eco-mode ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 90 set eco-mode This command enables or disables the Eco-mode. The Eco-mode is a function that turns off the disk motor when the disks are not being accessed. The Eco-mode function cannot be used unless the Eco-mode is enabled. ■ Syntax ■ Parameter ■ Example(s) set eco-mode [-mode {enable | disable}] -mode Optional. This parameter specifies if the Eco-mode is enabled. If omitted, the existing setting is not changed. enable Eco-mode is enabled. disable Eco-mode is disabled. The following example enables the Eco-mode. CLI> set eco-mode -mode enable The following example disables the Eco-mode: CLI> set eco-mode -mode disable

3.1 RAID Group Management > show eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 91 show eco-schedule This command displays a summary of the Eco-mode schedules and the Eco-mode schedule events. ■ Syntax ■ Parameter ■ Output show eco-schedule [-schedule-number schedule_numbers | -schedule-name schedule_names] -schedule-number or -schedule-name Optional. This parameter specifies the Eco-mode schedule identifier to display details. One or more Eco-mode schedule identifiers can be specified. If this parameter is omitted, all the Eco- mode schedules are displayed. For details, refer to "1.2.14 Eco-mode Schedule Syntax" (page 29). schedule_numbers Eco-mode schedule number schedule_names Eco-mode schedule name ECO Schedule Eco-mode schedule identifiers No. Eco-mode schedule number Name Eco-mode schedule name Event Eco-mode schedule event identifiers No. Eco-mode schedule event number Type Eco-mode schedule event type Details Explanation for the Eco-mode schedule event type Time Starting time and ending time of the Eco-mode schedule

3.1 RAID Group Management > show eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 92 ■ Example(s) The following example displays a list of all the registered Eco-mode schedules: CLI> show eco-schedule ECO Schedule No. Name --- ---------------- 0 SC001 1 SC002 2 SC003_TEMP The following example displays the schedule information of the Eco-mode schedule named "SC001": CLI> show eco-schedule -schedule-name SC001 ECO Schedule No. Name --- ---------------- 0 SC001 Event No. Type Details Time --- ------------- ----------------------------------------- ----------------------- 1 Every-day from [06:00] to [18:00] 2 Every-week Monday-Friday from [06:00] to [18:00] 3 Specific-day 6days from December 13 from [06:00] to [18:00] 4 Specific-week December 1st week Monday-Friday from [06:00] to [18:00] The following example displays the schedule information of the Eco-mode schedules named "SC002" and "SC003_TEMP" at the same time: CLI> show eco-schedule -schedule-name SC002,SC003_TEMP ECO Schedule No. Name --- ---------------- 2 SC002 Event No. Type Details Time --- ------------- ----------------------------------------- ----------------------- 1 Every-day from [06:00] to [18:00] 2 Every-week Monday-Friday from [06:00] to [18:00] ECO Schedule No. Name --- ---------------- 3 SC003_TEMP Event No. Type Details Time --- ------------- ----------------------------------------- ----------------------- 1 Specific-day 6days from December 13 from [06:00] to [18:00] 2 Specific-week December 1st week Monday-Friday from [06:00] to [18:00]

3.1 RAID Group Management > create eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 93 create eco-schedule An Eco-mode schedule is a schedule that applies Eco-mode functions. The Eco-mode schedule specifies the time that a disk motor is rotated (it does NOT specify when the motor will be turned off). A maximum of 64 Eco-mode schedules can be created. One Eco-mode schedule consists of a maximum of 8 Eco-mode schedule events (at least one Eco-mode schedule event is required in one Eco-mode schedule). This command can create one Eco-mode schedule and only one Eco-mode schedule event. If two or more Eco-mode schedule events are created and defined, use the "set eco-schedule" command. Refer to the following: ■ Syntax ■ Parameter Max 64 ... Eco-mode schedules Eco-mode schedules Schedule-Event #1 Schedule-Event #7 Schedule-Event #8 Schedule-Event #5 Schedule-Event #6 Schedule-Event #2 Schedule-Event #3 Schedule-Event #4 create eco-schedule -name schedule_name -event-type {every-day | every-week,{mon|tue|wed|thu|fri|sat|sun},{mon|tue|wed|thu|fri|sat|sun} | specific-day,MMDD,R | specific-week,MM,{1st|2nd|3rd|4th|last},{mon|tue|wed|thu|fri|sat|sun},{mon|tue|wed|thu|fri|sat|sun}} -event-from hhmm -event-to hhmm -name This parameter specifies the Eco-mode schedule name. Only one Eco-mode schedule name can be specified. For details, refer to "1.2.14 Eco-mode Schedule Syntax" (page 29). schedule_name Eco-mode schedule name -event-type This parameter specifies the Eco-mode schedule event type. every-day The Eco-mode schedule is applied to every day. A suboperand is not required. Example: -event-type every-day every-week The Eco-mode schedule is applied to every week. This format is "every- week,STA,END". The start day of the week (STA) and the end day of the week (END) are separated by a comma (,). The day of the week must be specified in the following format. The end day of the week must be after the start day of the week. The first day starts from Monday.

3.1 RAID Group Management > create eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 94 Example: Correct -> -event-type every-week,mon,fri (from Monday to Friday is OK) Example: Incorrect -> -event-type every-week,fri,tue (from Friday to Tuesday is not OK) Example: Correct -> -event-type every-week,mon,mon (only Monday is OK) mon Monday tue Tuesday wed Wednesday thu Thursday fri Friday sat Saturday sun Sunday specific-day The Eco-mode schedule is applied to a specific day. This format is "specific- day,MMDD,R". The specific month MM (01 – 12) and the specific day DD (01 – 31) are separated by a comma (,) (when every month is required, specify "em" instead of 01 – 12). When the last day of the month is required, specify "99" instead of 01 – 31. The number of days that the schedule will apply is specified as R, and a value between 1 – 7 can be set. Example: -event-type specific-day,0501,3 (For three days, from May 1st to May 3rd) Example: -event-type specific-day,0630,2 (For two days, from June 30th to July 1st) specific- week The Eco-mode schedule is applied to a specific week. This format is "specific- week,MM,W,STA,END". The specific month MM (01 – 12) and the specific week W (1st, 2nd, 3rd, 4th, or last) are separated by a comma (,) (when every month is required, specify "em" instead of 01 – 12). The start day of the week (STA) and the end day of the week (END) are separated by a comma (,). The day of the week must be specified in the following format. The end day of the week must be after the start day of the week. The first day starts from Monday. Example: -event-type specific-week,05,3rd,mon,wed (From the 3rd Monday to the 3rd Wednesday in May) Example: -event-type specific-week,05,3rd,wed,mon (From the 3rd Wednesday to the 3rd Monday in May) (When May 1st is a Monday) mon Monday tue Tuesday wed Wednesday thu Thursday fri Friday sat Saturday sun Sunday

3.1 RAID Group Management > create eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 95 ■ Example(s) -event-from This parameter specifies that the Eco-mode schedule will start at a specific time. The format is "hhmm". "hh" is the starting hour (00 – 23) and "mm" is the starting minute (00 or 30). A disk motor will power ON at the time specified by this parameter. -event-to This parameter specifies that the Eco-mode schedule will end at a specific time. The format is "hhmm". "hh" is the ending hour (00 – 23) and "mm" is the ending minute (00 or 30). The following example creates an Eco-mode schedule. The Eco-mode schedule name is "SC001". The Eco- mode schedule will apply every day from 06:00 to 18:00: CLI> create eco-schedule -name SC001 -event-type every-day -event-from 0600 -event-to 1800

3.1 RAID Group Management > set eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 96 set eco-schedule This command is used to add Eco-mode schedule events or make changes to the specified Eco-mode schedule. ■ Syntax ■ Parameter set eco-schedule {-schedule-number schedule_number | -schedule-name schedule_name} [-name schedule_name] [-event-number {1|2|3|4|5|6|7|8}] [-event-type {every-day | every-week,{mon|tue|wed|thu|fri|sat|sun},{mon|tue|wed|thu|fri|sat|sun} | specific-day,MMDD,R | specific-week,MM,{1st|2nd|3rd|4th|last},{mon|tue|wed|thu|fri|sat|sun}, {mon|tue|wed|thu|fri|sat|sun}}] [-event-from hhmm] [-event-to hhmm] -schedule-number or -schedule-name This parameter specifies an Eco-mode schedule identifier. Only one Eco-mode schedule identifier can be specified. For details, refer to "1.2.14 Eco-mode Schedule Syntax" (page 29). schedule_number Schedule number schedule_name Schedule name -name Optional. This parameter specifies a new Eco-mode schedule name. If omitted, the existing setting is not changed. For details, refer to "1.2.5 Alias Name Syntax" (page 23). schedule_name Schedule name -event-number Optional. This parameter specifies the Eco-mode schedule event number to change or to add the Eco-mode schedule event to the Eco-mode schedule. The Eco-mode schedule event number is a value from 1 to 8. Only one number can be specified. The Eco-mode schedule event number can be displayed by using the "show eco-schedule" command. If omitted, the Eco-mode schedule event specified by this parameter value is not changed. 1 – 8 Schedule event number -event-type Optional. This parameter specifies the Eco-mode schedule event type. If omitted, the existing setting is not changed. every-day The Eco-mode schedule is applied to every day. A suboperand is not required. Example: -event-type every-day

3.1 RAID Group Management > set eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 97 every-week The Eco-mode schedule is applied to every week. This format is "every- week,STA,END". The start day of the week (STA) and the end day of the week (END) are separated by a comma (,). The day of the week must be specified in the following format. The end day of the week must be after the start day of the week. The first day starts from Monday. Example: Correct -> -event-type every-week,mon,fri (from Monday to Friday is OK) Example: Incorrect -> -event-type every-week,fri,tue (from Friday to Tuesday is not OK) Example: Correct -> -event-type every-week,mon,mon (only Monday is OK) mon Monday tue Tuesday wed Wednesday thu Thursday fri Friday sat Saturday sun Sunday specific-day The Eco-mode schedule is applied to a specific day. This format is "specific- day,MMDD,R". The specific month MM (01 – 12) and the specific day DD (01 – 31) are separated by a comma (,) (when every month is required, specify "em" instead of 01 – 12). When the last day of the month is required, specify "99" instead of 01 – 31. The number of days that the schedule will apply is specified as R, and a value between 1 – 7 can be set. Example: -event-type specific-day,0501,3 (For three days, from May 1st to May 3rd) Example: -event-type specific-day,0630,2 (For two days, from June 30th to July 1st) specific- week The Eco-mode schedule is applied to a specific week. This format is "specific- week,MM,W,STA,END". The specific month MM (01 – 12) and the specific week W (1st, 2nd, 3rd, 4th, or last) are separated by a comma (,) (when every month is required, specify "em" instead of 01 – 12). The start day of the week (STA) and the end day of the week (END) are separated by a comma (,). The day of the week must be specified in the following format. The end day of the week must be after the start day of the week. The first day starts from Monday. Example: Correct -> -event-type specific-week,05,3rd,mon,wed (from the 3rd Monday to the 3rd Wednesday in May is OK) Example: Incorrect -> -event-type specific-week,05,3rd,wed,mon (from the 3rd Wednesday to the 3rd Monday in May is not OK) (When May 1st is a Monday)

3.1 RAID Group Management > set eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 98 ■ Example(s) mon Monday tue Tuesday wed Wednesday thu Thursday fri Friday sat Saturday sun Sunday -event-from Optional. This parameter specifies that the Eco-mode schedule will start at a specific time. The format is "hhmm". "hh" is the starting hour (00 – 23) and "mm" is the starting minute (00 or 30). If omitted, the existing setting is not changed. A disk motor will power ON at the time specified by this parameter. -event-to Optional. This parameter specifies that the Eco-mode schedule will end at a specific time. The format is "hhmm". "hh" is the ending hour (00 – 23) and "mm" is the ending minute (00 or 30). If omitted, the existing setting is not changed. The following example adds Eco-mode schedule event #2 in the Eco-mode schedule named "SC001": CLI> set eco-schedule -schedule-name SC001 -event-number 2 -event-type every-day -event-from 0600 -event-to 1800 The following example changes the Eco-mode schedule name. The new Eco-mode schedule name is "SC002_NEW": CLI> set eco-schedule -schedule-name SC001 -name SC002_NEW

3.1 RAID Group Management > delete eco-schedule ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 99 delete eco-schedule This command deletes an Eco-mode schedule(s) or a single Eco-mode schedule event. One or more Eco-mode schedules can be deleted at the same time. Only one Eco-mode schedule event can be deleted at the same time. ■ Syntax ■ Parameter ■ Example(s) delete eco-schedule {-schedule-number schedule_numbers | -schedule-name schedule_names} [-event-number {1|2|3|4|5|6|7|8}] -schedule-number or -schedule-name This parameter specifies the Eco-mode schedule identifier. One or more parameters can be specified. However, if one or more parameters are specified, the "-event-number" parameter cannot be specified. For details, refer to "1.2.14 Eco-mode Schedule Syntax" (page 29). schedule_numbers Schedule number schedule_names Schedule name -event-number Optional. This parameter specifies the Eco-mode schedule event number to be deleted. The Eco-mode schedule event number is a value from 1 to 8 and can be displayed by using the "show eco-schedule" command. Only one event number can be specified. If the event-number is omitted, the Eco-mode schedule is deleted. 1 – 8 Schedule event number The following example will delete the Eco-mode schedule named "SC002": CLI> delete eco-schedule -schedule-name SC002 The following example will delete Eco-mode schedule event #2 in the Eco-mode schedule named "SC001": CLI> delete eco-schedule -schedule-name SC001 -event-number 2 The following example will delete both the Eco-mode schedules named "SC002" and "SC003" at the same time: CLI> delete eco-schedule -schedule-name SC002,SC003

3.1 RAID Group Management > show eco-raid-group ETERNUS CLI User’s Guide Copyright 2014 FUJITSU LIMITED P2X0-1210-05ENZ0 100 show eco-raid-group This command displays a list of the RAID groups that have an Eco-mode schedule associated with them. ■ Syntax ■ Parameter No parameters. ■ Output show eco-raid-group RAID Group RAID group identifiers No. RAID group number Name RAID group name Level RAID level Status RAID group status Assigned CM Controller module to be assigned to the target RAID group Capacity (MB) RAID group capacity ECO Schedule Eco-mode schedule identifiers Action Eco-mode schedule action. It means whether the Eco-mode schedule is associated. No. Eco-mode schedule number (In the case of a schedule by a cooperative software, "128" is displayed.) Name Eco-mode schedule name (In the case of a schedule by a cooperative software, "External" is displayed.) Motor Status Current status of the disk motors Control Status Control status by a control command