Sealife SL962 Instruction Manual

SL962 Optical cable connection for external flash Thank you for purchasing the SeaLife Flash Link. The Flash Link will ensure the external flash fires, regardless of the ambient light or position of the flash head, resulting in brighter, more colorful pictures. Please follow these instructions for proper connection and care of your Flash Link optical cable system. www.sealife-cameras.com/service/manuals.html Español - Deutsch - Français - Italiano

Please check the packaging content to see that you received all of the Flash Link parts. If you are missing any parts, please contact us at [email protected] or call (856)866-9191. 2

Insert flash sensor adapter into the rubber hole of the flash head, by stretching the armor around the sensor adapter.

Make sure flash sensor adaptor is seated correctly in locator device. Pull back armor to reveal locator device. NOTE: If your flash does not have the sensor locator device (item# SL96205) consider having one installed by your local SeaLife dealer or the SeaLife Service Center. The sensor locator device may not fit on SeaLife flashes produced prior to 2005.

Insert flash sensor cover into rubber hole of flash head farthest away from camera. Note: SeaLife Flash may already have sensor cover inserted.

This section applies if you are attaching the Flash Link to a SeaLife film camera and digital camera model DC100, DC200, DC250, DC300 or DC310. Skip this section if attaching Flash Link to another camera. The correct SeaLife deflector is included with your SeaLife Camera. The deflector adapter will attach to any of these deflectors as described in the instructions.

Attach cable adapter to deflector so that the top of the adapter is aligned in directly front of the camera’s flash window.

Remove deflector from flash base and insert cable to the top of the adapter. Re-attach deflector to flash base after cable is inserted. 7 9

This section applies to SeaLife Digital DC500 and DC600 cameras only. For non-SeaLife Cameras skip to the next section. Strip back 1/5” (5mm) of the black cable sheathing. Use cable stripper tool or carefully cut sheathing making sure not to cut into the optical cable. 10

Insert cable into one of the two holes in the camera adapter as shown. Keep pushing cable up so it bends and points towards the camera’s flash. Use small Allen wrench provided to tighten screw. DO NOT over tighten screw or this can damage the cable. 11

Attach Flash Link to camera as shown. Make should be relaxed and not twist in such a way that will pull it of the camera. You may want to use a small zip tie to keep the adapter firmly attached to the camera, if necessary. 12

For all non-SeaLife Cameras. Remove tape backing on hook Attach over flash window and look tape provided. of housing, press firmly! 12 13

Insert cable into adapter so cable is flush with hook and loop tape. 14

Tighten screw with wrench provided. Attach universal adapter DO NOT over tighten screw!! with cable positioned away from lens. 15

Suggestion: Use a low-profile zip tie to secure cable to top and bottom of flash arm (zip ties not provided).

• After connecting the Flash Link, and before each dive, test fire the flash on land in brightest possible light conditions to make sure Flash Link is working. • Regularly check that the open end of the optical cable is positioned directly in front of the camera’s flash. • Regularly check that cable end has a clean cut with nothing obstructing the optical core of the cable. If not clean, cut off end with a sharp razor. • Clean cable assembly with fresh water and dry after each use, and allow drying time before storage. • Prevent the cable from being crushed during storage and transportation. • Don’t bend or kink cable. Inspect and replace damaged cable. 18

connected to isolate the source of the problem. Without the Flash Link connected, aim the camera at the flash head sensor and take a picture. Do this test in a low-light or shaded area. The picture should show the flash firing. If not, refer to the SeaLife Flash instruction manual for helpful troubleshooting guidelines. Keep reading if the source of the problem is the Flash Link connection. • Inspect cable for any sharp bends or kinks, which may indicate the optical core of the cable is broken. Replace or cut-off damaged cable. • Make sure the camera side of the cable is positioned directly in front of the camera’s onboard flash. • Make sure the flash-head side of the cable is directly aligned over the flash light sensor. Newer SeaLife Flashes include a sensor locator device (item# SL96205), which helps to align the camera to the flash light sensor. If your flash does not have a sensor locator device, consider having one installed by your local SeaLife dealer or the SeaLife Service Center. 19

unobstructed. If you need to cut the cable end, use a sharp razor blade. • Make sure the small screw that secures the cable to the adapter has not been over tightened and damaged the cable. Loosen the screw using the Allen wrench provided and inspect the cable. If the cable is crushed, cut off the end of the cable as described above. To re-attach the cable, slowly tighten the screw in 1/2 turn increments using the Allen wrench provided. Pull on the cable after every 1/2 turn until it’s secure. Be very careful not to over tighten the screw or you will damage the cable. • Make sure flash sensor cover is in place on the sensor farthest from the camera (See page 5) • If you still experience a flash firing issue after reviewing the above information, please send the camera system to the SeaLife Service department for a complete evaluation.

period of 1 year from the original date of purchase. If you require service, please make sure to obtain a return authorization # by contacting the authorized service center in your country or to the USA service facility at the address provided below. Once you have a return authorization #, ship the Flash Link, freight prepaid, to the authorized service center in your country or to the USA service facility at the address provided below. Please include a letter describing the problem, your return address (No PO Box), phone number and a copy of your original purchase receipt. The USA Service Center is open M - F, 8:30 am to 5:00 pm (EST). You may contact the service center at (856) 866-9192 or email us at [email protected] SeaLife Cameras, 97 Foster Road, Suite 5, Moorestown, NJ 08057 USA 21