Quantum SuperLoader 3A Operation & User’s Manual

$ 6XSHU/RDGHUŒ$6HULHV 6XSHU/RDGHU$ 5SERS'UIDE5SERS'UIDE5SERS'UIDE5SERS'UIDE5SERS'UIDE5SERS'UIDE5SERS'UIDE

Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. COPYRIGHT STATEMENT Copyright 2007 by Quantum Corporation. All rights reserved. Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law. TRADEMARK STATEMENT Quantum, DLT, DLTtape, The Quantum Logo, and The DLTtape Logo are all registered trademarks of Quantum Corporation. SuperLoader, SDLT, and Super DLTtape are trademarks of Quantum Corporation. Other trademarks may be mentioned herein which belong to other companies.

iii Contents Preface ix Chapter 1 Introduction 1 SuperLoader 3A Series............................................................................... 1 Media Inventory ......................................................................................... 2 Ethernet Interfaces...................................................................................... 2 Chapter 2 Operating the Autoloader 4 Using the Front Panel........................................................................................ 5 Entering Passwords.................................................................................... 7 Logging Out ................................................................................................ 7 Configuring the Autoloader............................................................................. 7 Using the Remote Management Ethernet Port....................................... 9 Setting the IP Address................................................................................ 9 Setting the Subnet Mask .......................................................................... 10 Setting the IP Gateway............................................................................. 11 Setting the SNMP Server ......................................................................... 11 Setting the Time ........................................................................................ 12 Setting the Time Server............................................................................ 12 Setting the Change Mode ........................................................................ 14

iv Setting Security ......................................................................................... 14 Setting Passwords..................................................................................... 15 Getting Lost Passwords ........................................................................... 16 Using Cartridges .............................................................................................. 16 Inserting a Single Cartridge .................................................................... 18 Moving a Single Cartridge ...................................................................... 19 Ejecting a Single Cartridge ...................................................................... 20 Using Magazines and Magazine Blanks....................................................... 22 Ejecting a Magazine.................................................................................. 23 Using the Magazine Load/Unload Command .................................... 23 Installing a Magazine ............................................................................... 24 Manually Operating the Magazine ........................................................ 24 Viewing Status Information ........................................................................... 26 Autoloader Status ..................................................................................... 26 Firmware Version ..................................................................................... 27 Element Status........................................................................................... 27 Tape Drive Status...................................................................................... 28 Tape Drive Version................................................................................... 29 FTP Server Version................................................................................... 29 Ethernet Information................................................................................ 29 Running an Inventory ..................................................................................... 30 Using Data Compression................................................................................ 30 Chapter 3 On-board Remote Management 31 Accessing On-board Remote Management.................................................. 32 Opening On-board Remote Management............................................. 33 Viewing Status Information .................................................................... 33 Default Username and Password........................................................... 34 Time Display ............................................................................................. 34 Feedback on Pages.................................................................................... 34 Configurations Page ........................................................................................ 35 System Operations Options..................................................................... 35 Setting Network Options......................................................................... 39 Setting Security Options .......................................................................... 40 Updates Page.................................................................................................... 43 FTP Server Updates.................................................................................. 44 Diagnostics Page .............................................................................................. 45 Running Diagnostic Tests........................................................................ 45 Viewing Error or History Logs............................................................... 45 Diagnostics................................................................................................. 46 Sales Demo................................................................................................. 46

v Identification.............................................................................................. 46 Performing a System Reset...................................................................... 47 Commands Page .............................................................................................. 47 Moving Tapes............................................................................................ 47 Inventory.................................................................................................... 48 Set to Home ............................................................................................... 48 Chapter 4 Customer Replaceable Units (CRUs) 49 Replacing a Magazine or Magazine Blank................................................... 49 Removing a Magazine.............................................................................. 50 Removing a Blank..................................................................................... 50 Installing a Magazine ............................................................................... 50 Installing a Blank ...................................................................................... 51 Changing the Orientation........................................................................ 51 Chapter 5 Troubleshooting 54 Before Contacting Customer Support........................................................... 54 Autoloader Troubleshooting.......................................................................... 58 Autoloader Logs ....................................................................................... 58 Retrieving the Hard Log.......................................................................... 60 Hard Log Example.................................................................................... 61 Time Stamp................................................................................................ 61 Error............................................................................................................ 62 Power-on Self Test (POST).............................................................................. 71 Performing a POST................................................................................... 72 Interpreting the POST Results ................................................................ 72 Diagnostic Tests from the Front Panel.......................................................... 73 Setting the Security................................................................................... 73 Stopping a Diagnostic Test...................................................................... 74 Front Panel Diagnostic Tests................................................................... 74 On-board Remote Management Diagnostic Tests ...................................... 76 Diagnostics Using On-board Remote Management............................ 76 Returning the Autoloader for Service........................................................... 77 Preparing the Autoloader for Shipment................................................ 77 Removing the Autoloader from a Rack................................................. 77 Packing the Autoloader ........................................................................... 78

vi Appendix A Specifications 79 SuperLoader 3A Series Autoloader............................................................... 80 Physical Specifications ............................................................................. 80 Performance Specifications ..................................................................... 80 Environmental Specifications ................................................................. 81 Power Specifications................................................................................. 82 Vibration Specifications ........................................................................... 82 Shock Specifications ................................................................................. 82 A-Series SDLT 600A Tape Drive.................................................................... 83 Drive Specifications.................................................................................. 83 Media Capacity ......................................................................................... 83 Media Specifications................................................................................. 83 A-Series LTO-3A Tape Drive ......................................................................... 85 Drive Specifications.................................................................................. 85 Media Capacity ......................................................................................... 85 Media Specifications................................................................................. 86 Appendix B Regulatory Statements 87 FCC Statement.................................................................................................. 87 Taiwan Statement ............................................................................................ 88 Japan Notice...................................................................................................... 88 Canadian Notice (Avis Canadien)................................................................. 88 European Union Notice .................................................................................. 89 Product Safety Electrostatic Discharge......................................................... 90 Grounding Methods........................................................................................ 90 Environmental Compliance............................................................................ 91 Disposal of Electrical and Electronic Equipment ....................................... 91 Glossary 92 Index 104

vii Figures Figure 1 Back Panel Overview................................................................... 3 Figure 2 Front Panel .................................................................................... 5 Figure 3 System Menu Tree........................................................................ 8 Figure 4 Left and Right Sides of a Magazine......................................... 22 Figure 5 Magazine and Blank .................................................................. 52 Figure 6 Removing the Screws from the Handle.................................. 53

viii Tables Table 1 Storage Capacity and Transfer Rates ........................................ 2 Table 2 Front Panel LEDs.......................................................................... 6 Table 3 Autoloader Status....................................................................... 26 Table 4 Firmware Version Fields........................................................... 27 Table 5 Drive Status Fields ..................................................................... 28 Table 6 Drive Version Fields .................................................................. 29 Table 7 Ethernet Information Fields...................................................... 29 Table 8 Probable Cause and Possible Solutions .................................. 55 Table 9 Log Retrieval Methods .............................................................. 59 Table 10 Error Code Listing and Suggested Actions............................ 63 Table 11 POST Descriptions ..................................................................... 71

ix Preface This document serves as an easy-to-use information source to familiarize Quantum customers and systems professionals with the SuperLoader 3A Series autoloader. Audience The primary audience for this document consists of end users installing and using an A-Series tape drive configured as part of the SuperLoader 3A Series autoloader. Purpose This document provides information on the SuperLoader 3A Series autoloader including: • Product description • Operation instructions • Remote and front-panel administration of the autoloader • Diagnostics • Customer Replaceable Unit (CRU) procedures • System log files and error logs • Troubleshooting • Specifications • Regulatory compliance and statements

x Document Organization This document is organized as follows: • Chapter 1, Introduction, provides a brief product overview. • Chapter 2, Operating the Autoloader, provides information about the operator's panel functionality, configuring the autoloader, and viewing status information from the front panel. • Chapter 3, On-board Remote Management, provides an on-board remote management overview, including configuration, updates, diagnostics, and commands pages. • Chapter 4, Customer Replaceable Units (CRUs), provides information about replacing a magazine or magazine blank. • Chapter 5, Troubleshooting, provides troubleshooting information about the autoloader, power-on self test (POST), and running diagnostics from the front panel and remote management pages. • Appendix A, Specifications, provides specifications for the SuperLoader 3A Series autoloader equipped with an A-Series tape drive. • Appendix B, Regulatory Statements, lists the applicable regulatory statements for the autoloader. This document concludes with a glossary and index. Notational Conventions This document uses the following conventions: Note: Notes emphasize important information related to the main topic. Caution: Cautions indicate potential hazards to equipment and are included to prevent damage to equipment. Warning: Warnings indicate potential hazards to personal safety and are included to prevent injury.

xi • Right side of the autoloader — Refers to the right side as you face the component being described. • Left side of the autoloader — Refers to the left side as you face the component being described. • Power cycle — Means to turn the autoloader or system on, then turn them off (or off, then on). • Dimensions in figures — All dimensions are shown with no units specified (Inches understood unless otherwise specified). Related Documentation Documents related to the Quantum SuperLoader 3A Series autoloader are shown below: Document No. Document Title Document Description 81-81667 SuperLoader 3A Series Quick Start Guide This guide contains a sequence of steps recommended for unpacking, installing, and setting up your autoloader. 81-81800 A-Series FTP File Server User’s Guide This guide provides information on how to use the FTP file server. 81-81237 How to Ship the Quantum SuperLoader This guide provides information on the proper packing for returning the autoloader for repair.

xii Contacts Quantum company contacts are listed below. Quantum Corporate Headquarters 0 To order documentation on this or other Quantum products, contact: Quantum Corporation 141 Innovation Drive Irvine, CA 92617 (949) 856-7800 (800) 284-5101 Technical Publications 0 To comment on existing documentation send e-mail to: [email protected] Quantum Home Page 0 Visit the Quantum home page at: www.quantum.com Global Services 0 Quantum Global Services provides 24-hour support that can be reached at: North/South America: (949) 725-2100 or (800) 284-5101 Asia/Pacific Rim: (International Code) + 65 6334 0660 Europe/Middle East/Africa: (International Code) + 44 (0) 1256 848748 Send faxes for the Customer Support Department to: North/South America: (949) 725-2176 Asia/Pacific Rim: (International Code) + 65 6432 2830 Europe/Middle East/Africa: (International Code) + 44 (0) 1256 848777

xiii Send e-mail for the Customer Support Department to: North/South America: www.quantum.com/am/service_support/Index.aspx Asia/Pacific Rim: [email protected] Europe/Middle East/Africa: [email protected]

1 Chapter 1 1Introduction Data backup is essential to protect irreplaceable information. Backing up data to magnetic tape is an easy, cost-efficient method used by many small and medium businesses. However, most enterprises have so much data that a single backup tape is not enough; the information has to be spread across numerous tapes. To avoid constantly changing tapes manually, many tape backup systems include Quantum autoloaders. Quantum autoloaders provide a compact, high capacity, and low cost method for simple, unattended data backup. The autoloader is compatible with popular operating systems such as Windows, MAC OSX, Linux, and environments that support FTP and Ethernet interfaces. SuperLoader 3A Series 1 The Quantum SuperLoader 3A Series autoloader contains an A-Series tape drive and one or two tape magazines holding up to eight cartridges each. Up to sixteen data cartridges can be used with two magazines. A single cartridge can be inserted directly into an empty tape drive via a password-protected mailslot or into an empty magazine slot. The Quantum A-Series Tape Drives are an extension to the family of products with video professionals in mind. Using the built-in FTP client in conjunction with a standard Web browser, Material Exchange Format (MXF) files can be stored and retrieved. A Gigabit Ethernet (GigE) interface allows these drives to be quickly connected and accessed on your network.

Quantum SuperLoader 3A Series User’s Guide 2 The A-Series tape drives are ideal for serving a full range of video applications; from hand-carrying video content out to a truck for live production to facility-wide, long-term, secure archive. The A-Series tape drives offer the following product features: Table 1 Storage Capacity and Transfer Rates Media Inventory 1 When the SuperLoader 3A Series is powered up, it undergoes a media inventory. Each tape cartridge in the autoloader is inserted into the A-Series tape drive and inventoried. Ethernet Interfaces 1 To get the full performance of the SuperLoader 3A Series autoloader, it is advisable to use a GigE network. The autoloader connects to your host server (see figure 1) via a built-in Gigabit Ethernet (GigE) interface (A-Series tape drive Ethernet port), allowing the host to send data and commands automatically. A-Series Tape Drive Maximum Storage Capacity Maximum Native Data Transfer Rate SDLT 600A 300 GB 36 MB/sec LTO-3A 400 GB 68 MB/sec Note: There is a limitation on the number of files that can be stored on a media cartridge based on the size of the files and the size of the filenames stored on the table of contents (TOC) region of the tape. For example, the A-Series SDLT 600A tape drive can hold approximately 8,000 files. This limit can be significantly smaller if the filenames are long and/or there are many MXF files. Note: Depending upon the number of cartridges in each magazine and the amount of content or data on each cartridge, the media cartridge inventory may take up to forty minutes.

Quantum SuperLoader 3A Series User’s Guide 3 You can also connect to the autoloader via a second Ethernet connection (Autoloader remote management Ethernet port) to perform administrative functions and download system updates. The GigE network port in the autoloader is backward compatible with 100BaseT and 10BaseT networks. Figure 1 Back Panel Overview 1 A-Series tape drive Ethernet port 2 Fan vent 3 Power connector 4 Autoloader remote management Ethernet port 5 Power switch

4 Chapter 2 2Operating the Autoloader Many of the operations you perform from the front panel can also be accessed from the On-board Remote Management interface of the autoloader (see chapter 3, On-board Remote Management). This chapter covers all aspects of operating the autoloader from the front panel. • Using the Front Panel • Configuring the Autoloader • Using Cartridges • Using Magazines and Magazine Blanks • Viewing Status Information • Running an Inventory • Using Data Compression Note: For information on installing your SuperLoader 3A Series autoloader in a standard 19-inch rack, see the Quantum SuperLoader 3A Series Quick Start Guide (81-81667) Note: For information on accessing and using the Quantum A-Series Tape Drive and FTP File Server, see the Quantum A-Series FTP File Server User’s Guide (81-81800)

Using the Front Panel Quantum SuperLoader 3A Series User’s Guide 5 Using the Front Panel The front panel consists of two LEDs, four function buttons, and a 2-line by 16-character LCD screen. A scrolling menu on the LCD screen allows you to obtain status information from the autoloader and enter commands. The front panel provides everything you need to monitor autoloader status and to control all of its functions. Figure 2 Front Panel 1 Power switch 2 Front panel LCD screen 3 Front panel LEDs 4 Scroll up button 5 Scroll down button 6 Escape 7 Enter Green Amber

Using the Front Panel Quantum SuperLoader 3A Series User’s Guide 6 The functionality of the two front panel LEDs is defined in table 2. Table 2 Front Panel LEDs When you first power on the Quantum SuperLoader 3A, it automatically runs a Power-on Self-Test (POST). During the POST, the left (Green) LED flashes. After the POST, the left (Green) and right (Amber) LEDs flash alternately back and forth. Do one of the following: • If the autoloader powers on successfully, continue configuring the autoloader (see Configuring the Autoloader). • If the autoloader does not power on successfully, check the following: • Power switch is on • Power cable is inserted correctly • No error code displays on the autoloader LCD • If you cannot resolve the problem, contact your service representative or go to www.quantum.com. When you first power on the autoloader, the setting for the Internet Protocol (IP) address is static with the address 192.168.20.128. If you want to use Dynamic Host Configuration Protocol (DHCP) to change the IP address, see Setting the IP Address on page 9. To determine the IP address when using DHCP, view the Ethernet status information. All the functionality accessed from the scrolling menu can be password- protected. Two levels of security are built into the menu. The lower-level Function Green Amber Power off OFF OFF Ready ON OFF Normal activity Flashing OFF Autoloader attention OFF Flashing Autoloader error OFF ON Note: The front panel requires a six-digit password to change the configuration (see Setting Passwords on page 15). The LCD front panel default password for the Administrator is 000000. The default password for the Operator is 111111.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 7 security is the operator level and the higher-level security is the administrator level. There is one password for each level. The administrator password allows access to all the functionality available. The operator password allows access to all the functionality in the Commands and Status submenus. Entering Passwords 2 Many functions on the autoloader may be password-protected to ensure data integrity. To access the menu items necessary to execute these functions, you must first enter your password (see Setting Passwords on page 15). All passwords are six numeric digits long. When you enter a password, all password-protected functionality is available until you close your browser session. If you do not use the front panel for a period of time, the main screen reappears on the LCD. When the main screen reappears, the autoloader has automatically logged you out. You will have to re-enter your password again to access the menu functionality. Logging Out 2 To log out of the autoloader, use the following procedure. 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Log Out, and then press Enter. Session Complete displays on the LCD. Configuring the Autoloader To configure the autoloader, start with the main menu on the front panel. If the main menu is not already visible on the LCD, press Enter. When you first power on the autoloader, the default is set with no password protection. However, after you set the security option, all the configuration functionality is password protected. You need an administrator-level password to configure the autoloader. Note: You can also press Escape to log out. Continue pressing Escape as required until the main screen displays.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 8 The front panel menu provides the following options: Figure 3 System Menu Tree To configure the Quantum SuperLoader 3A Series autoloader, you must verify the setup of the following: • Magazine(s) • Ethernet IP address (if you are not using DHCP) • SNMP server IP address only if SNMP is being used

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 9 • Time server IP address (or the time zone, date, and time, if configuring manually)—only if a time server is being used • Control mode • Security option Using the Remote Management Ethernet Port 2 Ethernet is the method used by the autoloader to access a network. Using the autoloader remote management Ethernet port (see figure 1 on page 3), you can access the On-board Remote Management interface of the autoloader over a network (see chapter 3, On-board Remote Management). To use this Ethernet connection, you must define the following: • A dynamic or static IP address for the autoloader (required) • A subnet mask (required) • An IP gateway (optional) • A Simple Network Management Protocol (SNMP) server (optional) • A time server, or set the time and time zone manually (optional) Setting the IP Address 2 An IP address is the address of any device attached to a network. Each device must have a unique IP address. IP addresses are written as four sets of numbers separated by periods ranging from 0.0.0.0 up to and including 255.255.255.255. IP addresses are either permanent or dynamically assigned. A permanent, or static, address remains the same each time the device connects to the network. A dynamic address may change each time the device connects to the network server using Dynamic Host Configuration Protocol (DHCP). To set a dynamic IP address: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Ethernet, and then press Enter. 3 From the Ethernet submenu, scroll to Set IP, and then press Enter. 4 Scroll to DHCP, and then press Enter. Please reboot to use DHCP displays on the LCD screen.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 10 5 Press and hold the power button on the front panel until System Shutdown wait 60 sec displays on the LCD. Power Off displays on the LCD, then the autoloader shuts off. 6 Press the power button again to power on the autoloader. The IP address is changed. To set a static IP address: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Ethernet, and then press Enter. 3 From the Ethernet submenu, scroll to Set IP, and then press Enter. 4 Scroll to Static IP, and then press Enter. The cursor automatically displays at the first digit. 5 At each position of the IP address, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. When you have advanced through all of the digits of the IP address, the autoloader displays Enter to save. 6 Press Enter. The Configuration submenu displays and the static IP is now in effect. You do not need to reboot the autoloader. 7 Press Escape or Enter to return to the Ethernet submenu. Setting the Subnet Mask2 Creating a subnet mask is a method of splitting IP networks into a series of subgroups, or subnets, to improve performance or security. To set a subnet mask: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Ethernet, and then press Enter. 3 From the Ethernet submenu, scroll to Set Subnet Mask, and then press Enter. 4 At each position of the Subnet Mask address, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. Note: If you make a mistake, press Escape to backspace to the digit you want to change.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 11 When you have advanced through all of the digits of the subnet mask address, the autoloader displays Enter to save. 5 Press Enter. New Subnet Mask xxx.xxx.xxx.xxx displays on the LCD. You do not need to reboot the autoloader. 6 Press Escape or Enter to return to the Ethernet submenu. Setting the IP Gateway 2 To set an IP gateway address: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Ethernet, and then press Enter. 3 From the Ethernet submenu, scroll to Set Gateway, and then press Enter. The cursor automatically displays at the first digit. 4 At each position of the gateway address, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. When you have advanced through all of the digits of the gateway address, the autoloader displays Enter to save. 5 Press Enter. New Gateway is xxx.xxx.xxx.xxx displays on the LCD. You do not need to reboot the autoloader. 6 Press Escape or Enter to return to the Ethernet submenu. Setting the SNMP Server 2 An SNMP server monitors a network by processing reporting activity in each network device (hub, router, bridge, and so on). The server uses this information to define what is obtainable from each device and what can be controlled (turned off, on, and so on). To set an SNMP server address: 1 From the main menu, scroll to Configuration, and then press Enter. Note: If you make a mistake, press Escape to backspace to the digit you want to change. Note: If you make a mistake, press Escape to backspace to the digit you want to change.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 12 2 From the Configuration menu, scroll to Ethernet, and then press Enter. 3 From the Ethernet submenu, scroll to Set SNMP Server, and then press Enter. The cursor automatically displays at the first digit. 4 At each position of the SNMP server address, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. When you have advanced through all of the digits of the SNMP server address, the autoloader displays Enter to save. 5 Press Enter. New SNMP Server xxx.xxx.xxx.xxx displays on the LCD. You do not need to reboot the autoloader. 6 Press Escape or Enter to return to the Ethernet submenu. Setting the Time 2 The system time is displayed by On-board Remote Management and it is used internally when logging events and errors. The system time is either regular time or power-on time. Regular time is Month/Date/Year Time, such as Nov/21/2004 19:28. Power-on time is Power On Cycles/Power On Hours. For example, POC: 00121, POH: 00002:07:45 where POC is the number of times the system has booted since it was manufactured, and POH is the number of hours, minutes, and seconds since the last system boot. If regular time is known, it will be used, otherwise power-on time is used. The SuperLoader 3A Series must be reset after each power up. The time can be reset automatically if a time server is configured. Setting the Time Server 2 If you locate a time server that is compatible with Simple Network Time Protocol (SNTP), you can connect the autoloader to a server that will supply the correct date and time. The autoloader uses this information to time stamp information in its memory. To set a time server address: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Ethernet, and then press Enter. Note: If you make a mistake, press Escape to backspace to the digit you want to change.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 13 3 From the Ethernet submenu, scroll to Set Time Server, and then press Enter. The cursor automatically displays at the first digit. 4 At each position of the time server address, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. When you have advanced through all of the digits of the time server address, the autoloader displays Enter to save. 5 Press Enter. New Time Server xxx.xxx.xxx.xxx displays on the LCD. You do not need to reboot the autoloader. 6 Press Escape or Enter to return to the Ethernet submenu. To set the time zone: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Time, and then press Enter. 3 From the Time submenu, scroll to Set Timezone, and then press Enter. The Time Zone screen displays, allowing you to set the hours. The cursor automatically displays at the first digit. 4 Scroll to set the number of hours difference between your local time and Greenwich Mean Time (GMT). 5 Scroll to set the number of minutes difference between your local time and GMT, then press Enter. The new time zone is set. 6 Press Escape or Enter as necessary to return to the main menu. To set the date and time: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Time, and then press Enter. 3 From the Time submenu, scroll to Set Date/Time, and then press Enter. The Date/Time screen displays, allowing you to set the date and time. The cursor automatically displays at the first digit. 4 The first four digits represent the current year. At each position of the year, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. Note: If you make a mistake, press Escape to backspace to the digit you want to change.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 14 5 The next two digits represent the current month. At each position of the month, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. 6 The next two digits represent the current day. At each position of the day, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. 7 The next two digits represent the current hour. At each position of the hour, use the up and down arrows to change the value of each digit. Press Enter. 8 The last two digits represent the current minute. At each position of the minute, use the up and down arrows to change the value of each digit. Press Enter to advance the cursor to the next digit. 9 Press Enter to save. 10 Press Escape as necessary to return to the main menu. Setting the Change Mode2 The 3A Series autoloader uses Random mode only. The Sequential mode is not supported. In Random mode, you (or the backup software) can specify which cartridge you want to use and where you want it to go. Setting Security 2 You can add security to the front panel by password-protecting the autoloader's functionality. The security setting only protects the front panel functionality. The default setting is Off, meaning that no password is required. However, you can enable the security option so that users must enter a password to access functionality. Security Option 2 When you first power on the autoloader, the security option is set to Off. Use the following procedure to enable the security option. You must have an administrator-level password to set passwords. To set the security option: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Security. If a check mark appears after the word, the security option is On. If no check mark appears, the security option is Off.

Configuring the Autoloader Quantum SuperLoader 3A Series User’s Guide 15 3 To change the option, press Enter. For example, if the security option was set to On, it is now set to Off, and no check mark displays. Setting Passwords 2 Many operations on the autoloader are password-protected to ensure data integrity. You can set passwords to administrator level and to operator level. Operator-level users have access to the Commands and Status menus. Administrator-level users have access to all functionality. To set a password: 1 From the main menu, scroll to Configuration, and then press Enter. 2 From the Configuration menu, scroll to Set Password, and then press Enter. 3 To set a password to the operator level, scroll to Operator. To set a password to the administrator level, scroll to Administrator, then press Enter. The Set Password screen displays. 4 Press Enter. If you are not logged in as Administrator, press Enter again to log in. A text box displays above the first asterisk. In the text box, scroll to the first character of the password. The cursor automatically appears at the first number of the password. 5 At each position of the password, use the up and down arrows to change the value of each number. Press Enter to advance the cursor to the next number. 6 Press Enter. The text box above the asterisk disappears and another text box displays above the next asterisk. 7 Repeat steps 5 and 6 to enter the remaining digits of the password. When you have entered six numbers, the autoloader displays Submit Password below the asterisks. 8 Press Enter to submit the password. Password Successfully changed appears on the LCD. 9 Press Enter. The Operator and Administrator options reappear. You can either enter another password, or press Escape or Enter as necessary to return to the main menu. Note: If you make a mistake, press Escape to backspace to the digit you want to change.

Using Cartridges Quantum SuperLoader 3A Series User’s Guide 16 Getting Lost Passwords 2 If you forget the administrator-level password, you cannot access the autoloader's functionality to enter a new password. In this case, you must call customer support. When you call, have the autoloader connected to the Ethernet and open On-board Remote Management. Using Cartridges Typically, when you first install the autoloader, you load your cartridges into the magazines and then load the magazines into the autoloader. However, you can insert and eject cartridges individually using the mailslot, or you can eject a magazine, manually load and unload cartridges, then load the magazine back into the autoloader. The Note: You can reset front panel passwords to the factory defaults from On-board Remote Management. However, if the On- board Remote Management passwords are lost, you must contact customer support. If you must contact customer support, be at the host computer with On-board Remote Management on line. From the main screen, click Configuration. The enter Network Password or User name screen displays. The customer support representative will need the number surrounded by asterisks to locate and reset your password. This is your “realm number”. Note: If security is enabled and you try to execute a command without entering a password, the autoloader displays the Enter Password screen until you enter a password. Once you enter a password, the autoloader takes you back to the command screen that you were at prior to entering the password.

Using Cartridges Quantum SuperLoader 3A Series User’s Guide 17 autoloader automatically detects the presence of a cartridge in the magazine slot. If you try to perform an illegal operation, the autoloader refuses to perform the operation. For example, if you try to load a cartridge through the mailslot to the drive, but the drive already contains a cartridge, the mailslot does not unlock. If you try to unload a cartridge from the drive while the autoloader is writing to the tape, the command will not be initiated until the write command is completed. Note: On the front panel menu, whenever you see Enter or Eject, it means the cartridge enters and leaves the autoloader through the mailslot. Whenever you see Load or Unload, it means the cartridge is loaded into or unloaded from the tape drive. Warning: If a tape cartridge is holding the mailslot door open on power up, the robot will not move. The system detects that the mailslot door is open but cannot detect the presence of the cartridge. If the mailslot door is open, the bar code scanner laser light may shine out the door and potentially cause physical injury. Warning: With the mailslot door open, do not insert your hand through the mailslot door. This is to prevent bodily injury from the robot. Precautions are in place to prevent the robotic mechanism functioning in this circumstance. Warning: If the tape cartridge is holding the mailslot door open during operation, the system keeps track of the tape movement and continues robotic motion. This can occur if the robot ejects the cartridge out through the mailslot door.

Using Cartridges Quantum SuperLoader 3A Series User’s Guide 18 Inserting a Single Cartridge 2 When you want to load a single cartridge into the autoloader, you can use the mailslot. However, if the Security option is turned on, you have to enter a valid password to unlock the mailslot before you can load a cartridge. When you insert a cartridge through the mailslot, you can load it into the tape drive or store it in a magazine slot. To Insert a Cartridge Into the Tape Drive: 2 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Enter, and then press Enter. 3 From the Enter submenu, scroll to To Drive, and then press Enter. The message Insert Tape, Push Until Prompted displays on the LCD. 4 Once you have inserted the cartridge, press Enter. 5 Press Exit to clear the command and return to the menu. To Insert a Cartridge Into a Magazine Slot: 2 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Enter, and then press Enter. Note: After Insert Tape, Push Until Prompted displays on the LCD, insert the cartridge. After approximately 5 seconds, the system automatically verifies that a cartridge is inserted and continues the process. The message Tape Loaded displays when successfully completed. Note: For the autoloader, push the cartridge in until it stops. The cartridge will be about 3 inches (7.5 cm) inside the mailslot. This may require that you push and have your fingers well within the mailslot opening. After insertion, the end of the cartridge will be visible at the back of the mailslot opening. Note: If the insert cartridge function fails, the cartridge ejects and you will have to repeat steps 3 and 4 again. The message Missed Tape appears.

Using Cartridges Quantum SuperLoader 3A Series User’s Guide 19 3 From the Enter submenu, scroll to To Location, and then press Enter. The message Insert Tape, Push Until Prompted displays on the LCD. 4 Once you have inserted the cartridge, press Enter. 5 Press Exit to clear the command and return to the menu. Moving a Single Cartridge 2 You can easily move a single cartridge from one location to another inside the autoloader. 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Move, and then press Enter. The Move screen appears under From:. Scroll to the current location of the cartridge you want to move. Slots that are occupied by a data cartridge are indicated by an asterisk (*). 3 From To:, scroll to the location to which you want to move the cartridge. Slots that are occupied by a data cartridge are indicated by an asterisk (*). Press Enter. 4 Press Enter. If you select an empty location, No Source Tape appears on the LCD. Choose a different location. Note: After Insert Tape, Push Until Prompted displays on the LCD, insert the cartridge. After approximately 5 seconds, the system automatically verifies that a cartridge is inserted and continues the process. The message Tape Loaded displays when successfully completed. Note: For the autoloader, push the cartridge in until it stops. The cartridge will be about 3 inches (7.5 cm) inside the mailslot. This may require that you push and have your fingers well within the mailslot opening. After insertion, the end of the cartridge will be visible at the back of the mailslot opening. Note: If the insert cartridge function fails, the cartridge ejects and you will have to repeat steps 3 and 4 again. The message Missed Tape displays.

Using Cartridges Quantum SuperLoader 3A Series User’s Guide 20 If you select a location that is already occupied, Destination Full appears on the LCD. Choose a different location. Ejecting a Single Cartridge 2 When you want to remove a single cartridge from the autoloader, you can specify the cartridge you want by bar code or location, or choose the cartridge currently in the tape drive. To eject a cartridge by bar code (if you have a bar code reader): 2 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Eject, and then press Enter. 3 From the Eject submenu, scroll to Tape, scroll to Mailslot, and then press Enter. 4 Scroll to By Barcode. A bar code label displays. 5 Scroll to the label that corresponds to the cartridge you want to eject. Press Enter. To eject a cartridge by location: 2 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Eject, and then press Enter. 3 From the Eject submenu, scroll to Tape, scroll to Mailslot, and then press Enter. 4 Scroll to By Location. Slots that are occupied by a data cartridge are indicated by an asterisk (*). The slot that is occupied by a cleaning tape is indicated with an @ sign, if Auto Clean is enabled. Scroll to the slot containing the cartridge you want to eject. 5 Press Enter. The cartridge you want is ejected from the mailslot.

Using Cartridges Quantum SuperLoader 3A Series User’s Guide 21 To eject a cartridge from the tape drive: 2 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Eject, and then press Enter. 3 From the Eject submenu, scroll to Cartridge, and then press Enter. 4 Scroll to From Drive, and then press Enter. The cartridge you want is ejected from the mailslot.

Using Magazines and Magazine Blanks Quantum SuperLoader 3A Series User’s Guide 22 Using Magazines and Magazine Blanks Figure 4 Left and Right Sides of a Magazine The autoloader will not run unless both magazine openings are properly closed. One way that you can close the openings is to use two magazines. Inside edge view of magazine Outside edge view of magazine

Using Magazines and Magazine Blanks Quantum SuperLoader 3A Series User’s Guide 23 If you use only one magazine, then you must fill the other magazine opening with a magazine blank for the unit to become operational. Ejecting a Magazine 2 When you want to remove several cartridges at once, eject the magazine(s) first. To eject a magazine: 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Eject, and then press Enter. 3 On the Eject submenu, scroll to Right Magazine or Left Magazine, and then press Enter. You will hear a distinctive popping sound as the appropriate magazine is ejected from the autoloader. Left magazine has been ejected or Right magazine has been ejected displays on the LCD. 4 Grasp the magazine by the handle with one hand and slide it out, supporting it underneath with the other hand. Using the Magazine Load/ Unload Command 2 When issuing a Load/Unload command to the autoloader, the system automatically ejects the right-hand magazine. To remove the left-hand magazine using the Load/Unload command, you must: 1 Remove the right magazine. Note: Magazines, magazine blanks, and magazine handles are not interchangeable between drives types. Please order the appropriate part numbers when replacing these items. Note: To prevent damage to the autoloader or the magazine, use both hands when removing the magazine from the autoloader, supporting the entire length of the magazine. Note: Once you eject a magazine, you must fully remove it or fully reinstall it before powering off the autoloader. Before returning a magazine to the autoloader, manually turn the wheels on the side of the magazine. If they move freely, the cartridges are properly seated. If the wheels do not turn freely, check the cartridges and remove and replace as needed.

Using Magazines and Magazine Blanks Quantum SuperLoader 3A Series User’s Guide 24 2 Replace the right magazine with a magazine blank. 3 Issue the Load/Unload command again. The system will then eject the left magazine. 4 If you want to have the magazine in the right-hand bay, replace the magazine blank in the right-hand bay with a cartridge magazine. Installing a Magazine 2 To install a magazine into the autoloader, use the following procedure. 1 Grasp the magazine by the handle with one hand and support it underneath with the other hand. 2 Slide the magazine into the magazine bay until it clicks. Make sure that you position the magazine correctly. It should slide into the magazine bay smoothly. If you meet resistance, verify the orientation of the magazine. The magazine is correctly installed when you feel it click into place and the front is flush with the front panel. Left Mag Inserted or Right Mag Inserted appears on the LCD. The autoloader automatically proceeds to run an inventory. Manually Operating the Magazine 2 The following section describes how to operate a magazine. There are two knobs located on each end of the magazine. You can move the slots within the magazine by turning these two knobs and aligning a slot with one of the two openings. You can use the openings in the magazine to load and unload cartridges from the eight slots within each magazine. Caution: Be careful not to turn the knob on the side of the magazine while the magazine is partially inserted into the autoloader. Doing so may cause damage to the magazine or the autoloader. Note: It is recommended that you fully remove the magazine to load and unload cartridges. If the magazine is not fully removed, do not rotate the magazine.

Using Magazines and Magazine Blanks Quantum SuperLoader 3A Series User’s Guide 25 To load cartridges into a fully ejected magazine: 2 1 To load cartridges into the magazine, center a slot within one of the openings located on the side of the magazine. 2 Properly orient the cartridge. 3 Fully insert the cartridge into the slot. When pushing the cartridge into the slot, you will feel a small resistance (detente) until the cartridge is properly latched into the slot. All forward progress stops when the cartridge is fully inserted. You can remove a cartridge in the same manner as you insert it. Use the knobs to center the desired slot(s) in the openings on the side of the magazine. Using your thumb and index finger, pull out the cartridge. You will feel a small resistance, but continue to pull the cartridge until it comes free. To unload cartridges from a fully ejected magazine: 2 1 Pull the ejected magazine until the large upper slot is accessible. 2 Rotate the desired slot into position (centered in the opening). Either load or unload a cartridge to that location. Do not expose more than the large upper opening when manually operating the magazine. To Identify a Slot: 2 Each slot has an identification number that is exposed when the slots are in the upper section of the magazine. With the magazine removed from the autoloader, you can see the identification mark on the top side of the magazine through one of two windows on the upper surface of the magazine. Each magazine has a unique identification number indicating whether it is the right or left magazine. The left magazine will indicate the number 1 and the right magazine will indicate the number 9. Note: There is a keying feature in each slot that only allows you to fully insert the cartridge one way.

Viewing Status Information Quantum SuperLoader 3A Series User’s Guide 26 Viewing Status Information From the scrolling menu on the LCD, you can view the autoloader status, firmware version, element status, tape drive status, tape drive version, and Ethernet information. Autoloader Status 2 The autoloader status provides information about: whether a magazine is installed or not, Ethernet connection status, and whether a bar code reader is installed or not. To view the autoloader status: 1 From the main menu, scroll to Status, and then press Enter. 2 From the Status submenu, scroll to Autoloader, and then press Enter. 3 From the Autoloader submenu, scroll to Status, and then press Enter. A list of messages similar to the following displays: Table 3 Autoloader Status Status Message Description Magazines L* The left magazine is present. R* The right magazine is present. SCSI ID not used Not used in the 3A Series autoloader. Mode Random The change mode is set to Random. Sequential Not used in the 3A Series autoloader. BC Reader Yes or No A bar code reader is present.

Viewing Status Information Quantum SuperLoader 3A Series User’s Guide 27 Firmware Version 2 To view the current firmware version, use the following procedure: 1 From the main menu, scroll to Status, and then press Enter. 2 From the Status submenu, scroll to Autoloader, and then press Enter. 3 From the Autoloader submenu, scroll to Version, and then press Enter. A list of messages appears on the LCD. The firmware version is listed as Firmware: VX.XX where X.XX is the current installed version of the firmware. Table 4 Firmware Version Fields Element Status 2 The element status reports the status of the magazine slots. The status indicates whether a slot contains a cartridge or not, and which slot is allocated as the cleaning cartridge's slot. To view an element's status: 1 From the main menu, scroll to Status, and then press Enter. 2 From the Status submenu, scroll to Autoloader, and then press Enter. 3 From the Autoloader submenu, scroll to Element Status, and then press Enter. 4 Press Enter. You can scroll through each of the slots. Slots that are occupied by a data cartridge are indicated by an asterisk (*). The empty slot that is assigned to a cleaning cartridge is indicated with an exclamation point (!). The slot that is occupied by a cleaning cartridge is indicated with an at sign (@). Field Description Firmware The number indicates the firmware version. EDC The number indicates the Error Correction Code that was generated when the firmware was installed. The autoloader uses this number to verify that the firmware and the memory holding the firmware are good. HW/ME Rev The numbers indicate the hardware/mechanical versions.

Viewing Status Information Quantum SuperLoader 3A Series User’s Guide 28 5 Scroll to the slot containing the cartridge for which you want to see the label, or the cartridge you want to move, and then press Enter. The Element Status screen displays the bar code label for that cartridge. A Move command also displays on the screen. If you want to move the cartridge, scroll until the location you want to move to appears under To:, and then press Enter. If you do not want to move the cartridge, press Escape. Tape Drive Status 2 To view the tape drive status, use the following procedure. 1 From the main menu, scroll to Status, and then press Enter. 2 From the Status submenu, scroll to Drive, and then press Enter. 3 From the Drive submenu, scroll to Status, and then press Enter. A list of messages displays. These messages may include: Table 5 Drive Status Fields Note: The Move command appears only if the security is disabled or if you are logged in as Administrator or Operator. Field Description SCSI ID Not used in the 3A Series autoloader. Loader LUN Not used in the 3A Series autoloader. Compr Indicates whether the tape drive compression is enabled or disabled. Drive Tape Indicates whether the tape drive is present or not.

Viewing Status Information Quantum SuperLoader 3A Series User’s Guide 29 Tape Drive Version 2 To view the tape drive version, use the following procedure. 1 From the main menu, scroll to Status, and then press Enter. 2 From the Status submenu, scroll to Drive, and then press Enter. 3 From the Drive submenu, scroll to Version, and then press Enter. A list of messages appears. These messages may include: Table 6 Drive Version Fields FTP Server Version 2 The firmware version of the FTP server cannot be viewed from the front panel display. To view the FTP server version or update the FTP server firmware, see Updates Page on page 43. Ethernet Information 2 To view the Ethernet information, use the following procedure. 1 From the main menu, scroll to Status, and then press Enter. 2 From the Status submenu, scroll to Ethernet, and then press Enter. A list of messages displays. These messages may include: Table 7 Ethernet Information Fields Field Description Product Type Indicates the type of drive installed. Version Indicates the version number of the drive. Field Description MAC Address Indicates the unique network identifier associated with the autoloader. IP Address or DHCP Indicates the static IP address or currently assigned dynamic IP address. Network Indicates whether the autoloader is connected to the network or not and at what speed.

Running an Inventory Quantum SuperLoader 3A Series User’s Guide 30 Running an Inventory The autoloader automatically runs an inventory whenever you power it on or insert a magazine. An inventory checks each magazine slot, the drive, the picker, and the mailslot to determine if a cartridge is present. Each tape cartridge in the autoloader is inserted into the A-Series tape drive and inventoried. If so, it also reads the bar code label, if available. If you need to run an inventory in addition to this, you can do so manually. To perform an inventory manually: 1 From the main menu, scroll to Commands, and then press Enter. 2 From the Commands submenu, scroll to Inventory, and then press Enter. The autoloader scans the bar codes of all the cartridges present. Using Data Compression Compressing the data means that the autoloader can write more data to the same amount of tape. Data compression is drive dependent and cannot be set from the front panel or On-board Remote Management. Your backup application package may also have information on compression. The front panel display indicates whether data compression is Enabled or Disabled (see Tape Drive Status on page 28). Note: Depending upon the number of cartridges in each magazine and the amount of content or data on each cartridge, the media cartridge inventory may take up to forty minutes. Note: No bar code labels can be read if there is a tape in the picker.

31 Chapter 3 3On-board Remote Management Many of the operations you perform with the On-board Remote Management interface can also be accessed from the front panel of the autoloader (see chapter 2, Operating the Autoloader). This chapter covers all aspects of operating the autoloader from the On- board Remote Management interface. • Accessing On-board Remote Management • Configurations Page • Updates Page • Diagnostics Page • Commands Page Note: The firmware in the autoloader is used for both standard and A-Series autoloaders. For the A-Series autoloader, SCSI ID, Fibre Channel, and Mode under System Operations on the Configurations Page may be displayed but have no effect on the operation of the unit:

Accessing On-board Remote Management Quantum SuperLoader 3A Series User’s Guide 32 Accessing On-board Remote Management The SuperLoader 3A Series provides a remote management Ethernet port (see figure 1) that allows you to access the On-board Remote Management interface. This interface includes a Web server that provides a Hypertext Markup Language (HTML)-based graphic user interface (GUI) for ease of use. Many of the operations that you perform from the front panel can also be performed remotely using On-board Remote Management. These functions include moving tapes, system operations options, networking options, security options, running diagnostic tests, and performing system updates. Note: The A-Series tape drive Ethernet port is used for normal operation of the autoloader. You can switch this Ethernet cable to the autoloader remote management Ethernet port or install a user-supplied Ethernet cable to this port and your host network port or router. Note: Only use the Diagnostic commands when the autoloader is known to be idle and unavailable to host backup/restore applications. Use of the Diagnostic commands from On-board Remote Management should not be issued while the autoloader is being used by host applications. The autoloader will recognize when the drive or autoloader is executing host commands and will respond appropriately to prevent application failures. A Diagnostic command issued between host application commands may not be recognized resulting in a failed application, such as a failed backup/restore job. Note: To log out of the system, you must close your browser to end the session.

Accessing On-board Remote Management Quantum SuperLoader 3A Series User’s Guide 33 Opening On-board Remote Management 3 On-board Remote Management has an HTML interface, which means you use a browser to open it. The following Web browsers are supported: • For Microsoft Windows—Microsoft Internet Explorer 5.5 or later • For Microsoft Windows 2003—Microsoft Internet Explorer 6.0 or later (with latest security patches) • For Redhat® 2.1—Mozilla™ 1.4.2 • Firefox™ 1.0 You need an operator password to access the Commands page, and you need an administrator password to access the Configuration, Diagnostics, and Updates pages. To open On-board Remote Management: 1 From your computer, open your Web browser. 2 In the browser's address field, enter the IP address for your autoloader (see Ethernet Information on page 29 to view the currently assigned static or dynamic IP address from the front panel of the autoloader). The Home page appears in your browser window. Viewing Status Information 3 Status information appears on the right-hand side of the Home page and every page of On-board Remote Management except for the Updates page. The status information is updated every 10 seconds. Changes to the status appear in the status window update, but may take approximately 60 seconds to refresh. You can also click Refresh Status to get an immediate update of system status. The menu headings also appear at the top of every page. To access the functionality under the menu heading, click the specific menu heading. The first time that you connect, On-board Remote Management prompts Note: When using the On-board Remote Management page with Microsoft Internet Explorer, be sure to enable the Allow META REFRESH option. On Internet Explorer version 6.0, this feature is controlled through the Tools>Internet Options menu selection under the Security tab.

Accessing On-board Remote Management Quantum SuperLoader 3A Series User’s Guide 34 you for your username and password, then displays the opening page for that menu. Default Username and Password 3 The default username for On-board Remote Management is guest. The default password is guest. The username and password are case sensitive and should be entered in all lower case letters. The default username and password are valid if no usernames have been configured. Time Display 3 The time displayed is either regular time or power-on time. Regular time is Month/Date/Year time, such as Nov/21/2004 19:28. Power-on time is Power On Cycles (POC)/Power On Hours (POH), such as POC:00121, POH:00002:07:45. • POC (5-digit number) is the number of times the system has booted since it was manufactured. • POH is the number of hours, minutes, and seconds that the system has been on since the current boot occurred. Feedback on Pages 3 If there is feedback from the system when you submit a request, the feedback appears beneath the submit button. In some cases, you may have to scroll to see the feedback information.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 35 Configurations Page The Configurations page includes a submenu on the left-hand side of the page. You can set the System Operations, Networking, and Security options from this page. System Operations Options 3 The options listed under System Operations include SCSI ID or Fibre Channel, Mode, Compression, Barcode Reader, Cleaning Tape, Magazines, and System Time. SCSI ID or Fibre Channel 3 Not used with the 3A Series autoloader. Mode 3 The 3A Series autoloader uses Random mode only. The Sequential mode is not supported. In Random mode, you (or the backup software) can specify which cartridge you want to use and where you want it to go. Compression 3 For the Quantum SuperLoader 3A Series autoloader, data compression is drive dependent. The front panel and On-board Remote Management will display whether or not compression is enabled. Compressing the data means that the drive can write more data to the same amount of tape. To view the compression setting: Note: Compression cannot be changed from the front panel or On- board Remote Management of the autoloader.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 36 From any page, click the Configuration heading. The Configuration screen displays. Under the Compression heading, the current compression setting is displayed as Compression Enabled or Compression Disabled. Barcode Reader 3 The bar code reader is enclosed within the body of the autoloader. The information from each label is stored in memory and available through SCSI and On-board Remote Management to the computer's operating system or backup application upon request. The barcode reader can be Enabled or Disabled. The SCSI Barcode Length entry sets the number of characters of the barcode returned by SCSI Read Element Data. Setting the barcode length to zero disables truncation of the barcode and the full barcode is returned in the SCSI Read Element Data. If utilizing the bar code reader, you must apply or slide the bar code labels into the appropriate slot on the front of each cartridge. The labels must conform to ANSI/AIM BC1 -1995 Uniform Symbology Specification Code 39. A set of bar code labels is initially included with the autoloader. Refer to www.quantum.com for information on obtaining additional bar code labels. Cleaning Tape 3 To enable or disable the Auto Clean function, you must also designate a full slot for the cleaning tape cartridge. If a slot has not been designated, the box displays None. To designate the cleaning tape slot: 1 Load a cleaning tape into an empty slot using the Commands page. 2 Enable or disable Auto Clean by selecting the check box. Note: If Auto Clean is disabled, the cleaning tape will automatically be ejected via the mailslot. Cleaning is managed by the backup package you have installed instead.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 37 To set Auto Clean: 1 From any page, click the Configuration heading. The Configuration screen displays. 2 Scroll to Cleaning Tape. If a check mark appears in the box next to Auto Clean, the option is enabled. To disable Auto Clean, click the box to remove the check mark. If no check mark appears in the box next to Auto Clean, the option is disabled. To enable Auto Clean, click the box to enter a check mark. 3 In the Cleaning Tape Location field, select the appropriate slot location where you installed the cleaning tape. If Auto Clean is disabled, cleaning is managed by the backup package you have installed instead. 4 Click submit. Magazines 3 This setting is used to report the number of storage elements and the element address to the host. This setting must match the physical configuration in order for correct information to be reported. This setting only affects the information reported to the host. This setting does not affect the access to magazine slots from the front panel or On-board Remote Management. Those interfaces are based on the physical configuration. When configured for Both magazines, the autoloader always reports 16 storage elements to the host. This allows the removal and reinstallation of magazines without affecting what is reported to the host. When configured for Left or Right, the autoloader will always report eight storage elements to the host. The element addresses vary depending on which magazine is configured. If Left or Right is selected, and both magazines are physically installed, the front panel and On-board Remote Management allow the user access to the other magazine, but the host will not have access. To set the Magazines option: 1 From any page, click the Configuration heading. The Configuration screen displays. 2 Scroll to Magazines. The Magazines options display.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 38 A check mark appears after the currently enabled mode. 3 Do one of the following: • To leave the Magazines mode unchanged, press Esc. • To change the Magazines configuration, scroll to the setting you want for the autoloader, selecting the appropriate check box, and then click submit. These settings include Both, Right, and Left. The message This will require a power cycle and ISV configuration change. Enter To Continue is displayed. • To continue with the change, press submit. The message Please power cycle the tape autoloader and reconfigure the ISV app. displays. System Time 3 The system time is displayed by On-board Remote Management and is used internally for logging events and errors (see Setting the Time on page 12). The system time must be reset each time the autoloader powers up. The time is reset automatically if a time server is configured (see Using the Remote Management Ethernet Port on page 9). Otherwise, the time must be set manually from the front panel or through On-board Remote Management. The time zone setting is not lost when powered off. To set the system time: 1 Using the first drop-down list next to Time Zone, select the number of hours difference between your local time and Greenwich Mean Time (GMT). 2 Below the Time Zone field, select the current Month drop-down list. Note: Whether connected to a time server or not, the autoloader automatically corrects for daylight savings time if the time was set using On-board Remote Management. If the time was set from the front panel of the autoloader, you must correct for daylight savings time manually. Note: For example, if you live in Colorado, the time difference is –6 hours in the summer and –7 hours in the winter.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 39 3 In the Day field, type the current day of the month. 4 In the Year field, type the current year. 5 In the Hour text box, type the current hour in 24-hour format. 6 In the Minute text box, type the current minute. 7 Click submit to save the information. Setting Network Options3 When you originally installed the autoloader, you set the Ethernet configurations through the front LCD panel. However, you can modify them through On-board Remote Management. The options include Current Network Parameters, Set IP, and Set Network Configuration. To change the Ethernet configurations: To view the Current Network Parameters: 1 From any page, click the Configuration heading. The Configuration screen displays. 2 From the Configuration menu, click Networking. The Current Network Parameters area displays the current IP address, MAC address, and the speed setting for the Ethernet connection. In the Set IP section, if a check mark appears in the box next to DHCP, the dynamic IP address option is enabled. This means that with every reset of the system, the IP address may change depending on the network administrator's settings. To Set IP address: 1 Clear the check box to remove the check mark from the DHCP field, if applicable. 2 In the IP address fields, type the static IP address using the key to move from box to box. 3 If no check mark appears in the box next to DHCP, the static IP address option is enabled. To change a static IP address, type in the new address in the IP address fields using the key to move from box to box. 4 To change the IP address from a static address to a dynamic address, click the box next to DHCP.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 40 To Set Network Configuration: 1 To change the values of the subnet mask, gateway, Simple Network Management Protocol (SNMP) server, or the time server, type in the new address, using the key to move from box to box. 2 Click submit. Setting Security Options3 When you enable the security option, users must enter a password to access the autoloader's front panel functionality. A password allows either administrator-level access or operator-level access (see Setting Security on page 14). To set Security: 1 From any page, click the Configuration heading. The Configuration screen displays. 2 On the left-hand side of the screen, click Security. The System Security section of the screen displays. 3 To enable front panel security, select the check box next to Front Panel Security Enabled. 4 If the check box is blank, the security option for the front LCD panel is not enabled. 5 Click submit. To Reset Front Panel Password: 1 From any page, click the Configuration heading. The Configuration screen displays. 2 On the left-hand side of the screen, click Security. 3 Select the check box next to Reset Front Panel Password. A check mark appears. 4 Click submit. To set User Administration: 1 From any page, click the Configuration heading. The Configuration screen displays. 2 On the left-hand side of the screen, click Security. 3 From the drop-down list next to Select User Type, select Operator 1, Operator 2, Administrator 1 or Administrator 2.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 41 4 In the Username field, enter a user name. 5 In the Password field, enter the new password. 6 In the Verify Password field, re-enter the same new password. 7 Click submit. To set the Client Authorization Control: 1 From any page, click the Configuration heading. The Configuration screen displays. 2 On the left-hand side of the screen, click Security. Scroll to Client Authorization Control. In this section is a list of the IP addresses that are authorized to perform functions using On-board Remote Management for this specific unit. There are two sets of IP address boxes. You can individually enable/disable and configure each set. • If enabled, each set can be used to specify either a range of IP addresses or a pair of specific IP addresses that are allowed to administer this unit. A set can also be used to specify a single IP address if the desired IP address is entered into both the “a” and “b” portions of the set. When a set is used to specify a range of IP addresses, the “b” portion of each address set must be greater than or equal to the “a” portion of that address set. • If neither set is enabled, any IP client can administer the unit. If a single set is enabled, only clients that pass the test specified by that set are allowed administrator access. If both sets are enabled, any client that passes either of the two filter tests can administer the unit. The Web server always allows any client to view the status information of the unit, regardless of the authorized client list or the overlap control policy. 3 Use the drop-down box to select Enable or Disabled. 4 Type the IP addresses in the appropriate boxes. 5 Click submit to save. Note: To view the list of currently defined users, click submit with Select User Type.

Configurations Page Quantum SuperLoader 3A Series User’s Guide 42 Client Overlap Control is a management policy on controlling how the Web server handles overlapping control requests from multiple clients on the authorized client list. The options include No Locking, Full Locking, and Time-Based Locking. • No Locking allows multiple clients to have unrestricted access to control the system as long as they are on the authorized client list. • Full Locking permits only one authorized client to issue control requests at a time. This client must release the lock by clicking the Home option in the upper frame of the page to permit other authorized clients to have control access. • Time-Based Locking is similar to Full Locking in that only one authorized client can have control access at once, but the lock is automatically released after the specified number of seconds of inactivity have elapsed. After selecting the appropriate policy by clicking the check box, click submit to save the changes. 1 From any page, click the Configurations heading. The Configurations screen displays. 2 On the left-hand side of the screen, click Security. 3 Select a security option from the Client Overlap Control options: • No locking allows multiple users to access the system and issue requests. • Full Locking allows only one user to access the system and issue requests. • Time-based Locking allows only one user to access the system and issue requests with the lock expiring after a designated amount of inactivity (in seconds). • Home is used to release a full or time-based lock and permit another user to access the system. 4 Click submit. Note: Locking is only available to users on the authorized client list. Note: To log out of the system, you must close your browser to end the session.

Updates Page Quantum SuperLoader 3A Series User’s Guide 43 Updates Page You can browse to find system updates (autoloader and tape drive firmware) and then upload the updates. To get system updates: 1 From any page, click the Updates heading. The Firmware Update screen displays. 2 Click Browse to navigate to the host system for the update file. The file should end in an .img extension. 3 Click Upload. 4 Click OK in response to the confirmation box. The autoloader automatically uploads the new code and processes it to the system. Note: By entering an improper range of IP addresses, a user could possibly lock out all IP clients from administering the autoloader. If this occurs, you can restore the default values by running Restore Default from the front panel Configuration Menu. Note: A Microsoft issue can keep a user from updating drive or loader firmware over the On-board Remote Management interface. This can occur under Windows Server 2003 with Service Pack 1 (SP1), or if a user has installed Microsoft Security Update MS05-019. This problem will appear with a 6F Communication Error message on the front panel with the warning light on. On-board Remote Management will continue to report the autoloader status as Initialization. Microsoft has described a workaround for this problem in their product with Technical Support Article 898060 (http:// support.microsoft.com/default.aspx?scid=898060). If this problem occurs, the autoloader should be restarted to avoid further communication errors.

Updates Page Quantum SuperLoader 3A Series User’s Guide 44 FTP Server Updates 3 Updates to the FTP file server are done through the FTP client using the A-Series tape drive Ethernet port. To determine the current version of FTP client firmware or to update the firmware: 1 Open a browser and enter the A-Series tape drive IP address (default is 10.10.10.10). The FTP client screen displays 2 From the Admin menu, click Login and enter admin for the password. 3 Click Update Server Firmware. The current firmware version displays. 4 To update the firmware version, click Browse and select the file. 5 Click Update to start the process. When the update completes, a prompt to reboot for changes to take effect displays. 6 Click Reboot. Note: The reboot process may take as long as five to seven minutes. After reboot completes, a media cartridge inventory is initiated. Depending upon the number of cartridges in each magazine and the amount of content or data on each cartridge, the media cartridge inventory may take up to 40 minutes.

Diagnostics Page Quantum SuperLoader 3A Series User’s Guide 45 Diagnostics Page From the Diagnostics page, you can run various tests on the autoloader. You can also view error and history logs, test progress, identify the physical unit in a rack, or reset the system. Running Diagnostic Tests 3 The diagnostic tests available on the autoloader include: • Loader–Self Test • Loader–Health Check • Loader–Picker Test • Loader–Magazine Test • Loader–Inventory Test • Sales Demo • RALU Logs Viewing Error or History Logs 3 To view error or history logs: 1 From any page, click the Diagnostics heading. The Diagnostics screen displays. 2 Under View Error and History Logs, click View Logs. You can also save the logs to a file by clicking Save Logs. If you save the logs to a file, you must select a destination folder within 60 seconds. Note: View Logs allows you to view a summary of the hardware, software and update logs for the autoloader. Save Logs saves detailed log information to a file for the autoloader. On some browsers, after saving logs, it may be necessary to click on Home to continue using the On-board Remote Management function.

Diagnostics Page Quantum SuperLoader 3A Series User’s Guide 46 Diagnostics 3 To view the various diagnostic options: 1 From any page, click the Diagnostics heading. The Diagnostics screen displays. 2 In the Diagnostics section, select the diagnostic test that you want to run from the Test drop-down menu. 3 Specify a loop count, if desired. 4 Click Start Test. 5 While the test is running, you can view the status of the test. From View Diagnostic Test Progress, click View Status. A separate screen indicates which test is running and the current status of the diagnostic test. 6 To refresh the status information, click View Diagnostic Test Progress, and then click View Status again. Sales Demo 3 Within the Diagnostics menu, the Sales Demo selection allows for a random access, load/unload (RALU) sequence. Identification 3 You can use the Identification feature of the autoloader by requesting the LCD backlight to flash for a specified number of seconds. This can be helpful in identifying the location of the autoloader in an equipment room. 1 From any page, click the Diagnostics heading. The Diagnostics screen displays. 2 Under Identification, enter the number of seconds in the Time (secs) field. 3 Click Identify. The LCD backlight flashes on the autoloader for the specified number of seconds.

Commands Page Quantum SuperLoader 3A Series User’s Guide 47 Performing a System Reset 3 You will use System Reset when making mode changes, magazine changes, and IP address changes. A system reset will take at least three minutes if there is a tape in the drive, or approximately 30 seconds otherwise. To perform a system reset: 1 From any page, click the Diagnostics heading. The Diagnostics screen displays. 2 Under the System Reset section, click System Reset. Commands Page You can move tapes, run a system inventory, or reset the picker to its home position from the Commands page. When you click Commands, the page displays. Moving Tapes 3 From a remote location, you can request that a tape be moved from one position to another. To move a tape: 1 From any page, click the Commands heading. The Commands screen displays. 2 From the Moving Tapes section of the page, click the drop-down menu under From: and select the current location of the tape that you want to move. 3 From the drop-down menu under To:, select the location to which you want to move the tape, and then click submit. Note: You can also click the slot on the graphic of the autoloader magazine to select and move a cartridge.

Commands Page Quantum SuperLoader 3A Series User’s Guide 48 Inventory 3 The autoloader automatically runs an inventory whenever you power it on or insert a magazine. If you need to run an inventory in addition to this, you can use On-board Remote Management to do it remotely. To run an inventory: 1 From any page, click the Commands heading. The Commands screen displays. 2 From the Commands page, click Inventory. The autoloader starts an inventory immediately. Set to Home 3 If the autoloader is not able to successfully execute a Moving Tapes or an Inventory command, try executing a Set to Home command, and then retry the move or inventory command again. The Set to Home command resets the autoloader as a means to help the autoloader recover from an unexpected internal condition. To set to Home: 1 From any page, click the Commands heading. The Commands screen displays. 2 From the Commands page, click Set to Home. This executes a reset command to the autoloader.

49 Chapter 4 4Customer Replaceable Units (CRUs) The SuperLoader 3A Series is not intended for customer servicing. Customer Replaceable Units (CRUs) are limited to replacing magazines or magazine blanks. Magazines are not interchangeable between the VS/SDLT drive types and LTO drive types used by the SuperLoader 3A Series. Replacing a Magazine or Magazine Blank To replace a cartridge magazine or magazine blank, you need to remove the current magazine or blank, and then install the new magazine or blank. If you currently have a magazine blank and wish to change it to a cartridge magazine, you must remove the blank first, and then insert a cartridge magazine. This allows for up to a maximum of 16 cartridges in the autoloader, plus one cartridge in the drive. Warning: If you choose to service the unit, the power cable must be removed from the unit and the electrical outlet before removing the cover. Failure to do so may cause severe bodily injury or damage to the equipment. Note: Handles are either right or left. They are not interchangeable between the left and right sides of the autoloader.

Replacing a Magazine or Magazine Blank Quantum SuperLoader 3A Series User’s Guide 50 Removing a Magazine 4 In most cases, you will remove a magazine by using the Eject command on the front panel menu. If you need to remove the magazine when the autoloader is powered off, you must remove it manually. Please contact Customer Support for more information. Removing a Magazine Using the Front Panel 4 1 On the menu, scroll to Commands. 2 Press Enter. 3 On the Commands submenu, scroll to Eject, and then press Enter. 4 On the Eject submenu, scroll to Right Magazine or Left Magazine, depending on which magazine you want to eject, and then press Enter. The magazine pops forward so that the front of the magazine is no longer flush with the front panel. 5 With one hand, grasp the magazine by the handle and slide it forward to remove. Place your other hand under the magazine to support it and prevent it from falling. Removing a Blank 4 Your autoloader comes equipped with either two magazines, or one magazine and one magazine blank. The autoloader will not function without both magazine bays equipped with either a magazine or a magazine blank. To remove a magazine blank: 1 Pull the magazine blank straight out. 2 Replace with another magazine blank or a cartridge magazine. Installing a Magazine 4 To install a cartridge magazine: 1 Grasp the magazine by the handle with one hand and support it underneath with the other hand.

Replacing a Magazine or Magazine Blank Quantum SuperLoader 3A Series User’s Guide 51 2 Slide the magazine into the magazine bay. Make sure you position the magazine correctly; it should slide smoothly. 3 The magazine is correctly installed when you feel it click into place and the front is flush with the front panel. Installing a Blank 4 To install a magazine blank: 1 Grasp the magazine blank by the handle with one hand and guide the blank into the magazine bay. 2 Slide the magazine blank into the magazine bay until it stops. Changing the Orientation4 A magazine or magazine blank can be configured to fit in the right or left magazine bay. The handle must be removed and the appropriate handle attached to match the orientation of the magazine or blank. To remove and attach a magazine handle, you will need a #1 Phillips screwdriver. Caution: Insert the magazine slowly to avoid damaging internal components or the autoloader. Note: The magazine blank is correctly installed when you feel it click into place and the front of the blank is flush with the front panel of the autoloader.

Replacing a Magazine or Magazine Blank Quantum SuperLoader 3A Series User’s Guide 52 Figure 5 Magazine and Blank Changing the Orientation of a Magazine 4 1 Remove the two screws that attach the handle to the front of the magazine. Inside edge view of magazine Outside edge view of magazine Magazine blank (right side handle shown)

Replacing a Magazine or Magazine Blank Quantum SuperLoader 3A Series User’s Guide 53 Figure 6 Removing the Screws from the Handle 2 Unsnap the handle carefully, being careful not to break the hinge. 3 Rotate the magazine 180 degrees so that what was the front of the magazine is now the back. 4 Attach the appropriate left or right handle to the front of the rotated magazine. 5 Snap the handle back onto the front of the magazine. 6 Install the two screws to attach the handle securely to the magazine. Changing the Orientation of a Magazine Blank 4 1 Remove the two screws that attach the handle to the front of the magazine blank. 2 Unsnap the handle carefully, being careful not to break the hinge. 3 Rotate the magazine blank 180 degrees so that what was the front of the magazine is now the back. 4 Add the appropriate right or left handle to the front of the rotated magazine blank. 5 Snap the handle back on the front of the magazine blank. 6 Install the two screws to attach the handle securely to the magazine blank. Screws

54 Chapter 5 5Troubleshooting This chapter provides troubleshooting information that might be helpful with problems encountered during autoloader operation. For troubleshooting information when working with FTP file transfers using the built-in FTP client and server, see the Quantum A-Series FTP File Server User’s Guide (81-81800-0x). • Autoloader Troubleshooting • Power-on Self Test (POST) • Diagnostic Tests from the Front Panel • On-board Remote Management Diagnostic Tests • Returning the Autoloader for Service Before Contacting Customer Support Errors that you may experience with your autoloader can range from severe hardware damage to simple connection problems. Before you return your autoloader, you may be able to fix the problem yourself by following some basic troubleshooting procedures. Other than drive cleaning, there is no recommended routine maintenance for the Quantum SuperLoader 3A Series autoloader.

Before Contacting Customer Support Quantum SuperLoader 3A Series User’s Guide 55 The front LCD provides some troubleshooting capabilities, but is limited. On-board Remote Management provides more detailed information about the present state of the autoloader and past performance, and is more helpful for troubleshooting errors. General troubleshooting information is shown in table 8 and describes the probable cause and suggested action for problems that you may encounter. For more detailed troubleshooting information, see Autoloader Troubleshooting. . Table 8 Probable Cause and Possible Solutions Warning: The SuperLoader 3A Series is not intended for customer servicing. If you do service the unit yourself, the power cable must be removed from the unit and the electrical outlet before removing the cover. Failure to do so may cause severe bodily injury or damage to the equipment. Problem Suggested Action The front panel does not display information. The connection to the LCD has failed. • Use On-board Remote Management to troubleshoot error. The user starts a code update from the front panel without inserting a tape. • Power cycle the unit. The autoloader does not respond from the front panel. Bug checks display immediately after loading a new version of firmware. The firmware is corrupted. • Reload the firmware. The autoloader is operating slowly. The autoloader is incorrectly configured for the operating system • Go to www.quantum.com for compatibility requirements.

Before Contacting Customer Support Quantum SuperLoader 3A Series User’s Guide 56 The autoloader does not turn on. The power cable or source is malfunctioning. The autoloader is incorrectly configured. • Check all outlets and power cables for proper connection. • Contact customer support. The front panel and light indicators do not turn on. • Verify that the autoloader is plugged in. • Verify that the power switch on the back is turned on. • Verify that the drive carrier assembly is locked into the autoloader chassis with the four screws supplied. • Contact customer support. The front panel does not display information, but light indicators above the front panel are turned on. • Connect to the autoloader using On-board Remote Management via the autoloader remote management Ethernet port (see figure 1 on page 3). Then issue a System Reset from the Diagnostics page. • Verify that the drive carrier assembly is locked into the autoloader chassis with the four screws supplied. • On the front panel, press and hold the power switch for 15 seconds, then turn the rear power switch off. Wait 60 seconds and turn the rear power switch back on. • Contact customer support. Problem Suggested Action

Before Contacting Customer Support Quantum SuperLoader 3A Series User’s Guide 57 The autoloader does not communicate with the host system via the Ethernet. • Verify that the A-Series tape drive Ethernet cable (see figure 1 on page 3) is connected to the correct hub. • Verify the Ethernet configuration settings via the front panel LCD. If the DHCP server is available, Ethernet status should indicate DHCP (see Ethernet Information on page 29, otherwise, you must set a unique IP address and a subnet mask. • Power off the autoloader by turning off the system from the front panel LCD and turning it back on. • Contact customer support. The application software reports a failure locating a piece of media or fails to move a piece of media as requested. • Use the On-board Remote Management tool and verify that the media is in the expected location internal to the autoloader. • Using On-board Remote Management diagnostic tool, execute the Loader–Health Check command. • Issue a System Reset either by using On-board Remote Management Diagnostics page System Reset, or by turning the power off from the front panel. • Contact customer support. The application software reports an error while reading or writing a piece of media. • Try a different piece of media. • Issue a System Reset either by using On-board Remote Management Diagnostics page System Reset, or cycle the power from the front panel. • Contact customer support. Other failures occur. • Issue a System Reset either by using On-board Remote Management Diagnostics page System Reset, or cycle the power from the front panel. • Contact customer support. Problem Suggested Action

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 58 Autoloader Troubleshooting Whenever any system or application actions occur, the autoloader generates logs recording the action. You can use some of these logs to troubleshoot errors. Errors are problems that occur while operating the autoloader and prevent the autoloader from completing a specific action When an error occurs, one of the following can happen: • No error message displays, but the autoloader fails to complete the requested action. • The screen displays the error message and the Hard Log records non- recoverable errors. Autoloader Logs 5 While there are other types of logs, only use the Hard Log to troubleshoot errors. This log helps determine the type of error, time of occurrence, and parts of the autoloader affected. The autoloader generates the following logs, all with the same basic format: Soft Logs 5 The Soft Log records the autoloader's history during different conditions. It is similar to the Hard Log but may have been overwritten by a recovery action. Update Logs 5 The Update Log records firmware changes and upgrades in the autoloader. It also records information when hardware is updated or changed. Note: To troubleshoot hard errors, you may need to power cycle, repair, or replace the unit

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 59 Shadow Logs 5 (Engineering use only) Boot Logs 5 The Boot Log keeps track of the boot status in terms of number of hours the unit has been powered on, the number of times the autoloader has been rebooted, and the reason for the reboot. Hard Logs 5 The Hard Log is used for troubleshooting purposes and is described in Retrieving the Hard Log. Entries in the Hard Log represent errors that were not recovered during normal retry operations. The following table indicates the ways in which you can retrieve each log type. Table 9 Log Retrieval Methods Each log records information such as time of the event, error codes, and context information. The key fields are the time stamp (in order to correlate the event with a possible application interruption), and the error type for which the event was logged. Log Type http Front Panel Soft Yes Yes Update Yes Yes Shadow Yes No Boot Yes No Hard Yes Yes

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 60 Retrieving the Hard Log 5 Partial information from the Hard Log can be retrieved from the front panel. The front panel displays only the most important information. You can retrieve complete Hard Log information through On-board Remote Management. Whenever the autoloader generates a Hard Log, On-board Remote Management automatically displays the log information. For front panel retrieval, you must request the information. By interpreting the information in this log, you can determine how to troubleshoot errors. To retrieve Hard log information from the front panel: 5 1 From the front panel LCD, scroll to Diagnostics, and then press Enter. The Diagnostics submenu displays. 2 From the Diagnostics submenu, scroll to Error Logs, and then press Enter. The Error Log submenu displays. 3 From the Error Logs submenu, scroll to Hard, and then press Enter. The log information displays. To retrieve Hard log information from On-board Remote Management: 5 1 From any screen, click the Diagnostics heading. The Diagnostics screen displays. 2 Click View Logs. 3 If you want to save logs to your hard drive, click Save Logs. If you save a log to a file, you must select a destination folder within 60 seconds.

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 61 Hard Log Example 5 The first line of the Hard Log shows the number of entries, queue size, and defines the queue wrap and erase parameters. The first line of each Hard Log event contains the information you are looking for. The highest number entry, shown at the bottom of the queue, contains the most recent event. You are interested primarily in the time stamp and error fields. Context information followed by the 12 double-words are for engineering use only and cannot be interpreted without firmware source code. **** Hard Log **** Block 1, 004/016 entries @ 64 bytes each, wrap @ 004, erase @ 008 0000: 2001-Jun-27, 17:24:06.001, Error: 002f0222, Context: 4802/00000000 65460621:00610004:ffffffff:ffffffff ff741e03:0075ff63:0566063f:007f0000 ffffffff:ffffffff:ffffffff:ffffffff 0001: 2001-Jun-27, 17:24:08.036, Error: c02f0223, Context: 4802/00000000 00000000:00000000:00000000:00000000 00000000:00000000:00000000:00000000 00000000:00000000:00000000:00000000 0002: 2001-Jun-27, 17:38:19.777, Error: 002f0222, Context: 4802/00000000 65460621:00610004:ffffffff:ffffffff ff741e03:0075ff63:0566063f:007f0000 ffffffff:ffffffff:ffffffff:ffffffff 0003: 2001-Jun-27, 17:38:21.812, Error: c02f0223, Context: 4802/00000000 00000000:00000000:00000000:00000000 00000000:00000000:00000000:00000000 00000000:00000000:00000000:00000000 Time Stamp 5 The time the event occurred. This field helps correlate the event with a possible application interruption. If the unit is unable to acquire the correct time/date from the SNTP time server or the front panel, the time stamp contains values indicating the power cycle number and the time an entry was written relative to that power cycle, listed as Power On Hours (POH). Note: The unit has no internal real-time clock and requires you to set the time of day from the front panel or the network interface (SNTP).

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 62 Error 5 The error fields are defined as follows: Recovery Action 5 Recovery Action defines what the autoloader will do based on the event that occurred. •If the value is 0, the autoloader continues operations. These events are typically soft recoverable events or events that are just recording an action for when the development team is working on enhancements. •If the value is nonzero, the autoloader must reboot in order to recover from the event. The reboot happens automatically. Task ID 5 Task ID defines what firmware task was being performed at the time of the event. Bits 31, 30 Bits 29-28 Bits 27-24 Bits 23-20 Bits 19-16 Bits 15-12 Bits 11-8 Bits 7-4 Bits 3-0 Recovery Action Task ID Error Type Context Information Task ID Description 00 System Timer 01 Loader Manager 02 Picker 03 Magazine Left 04 Magazine Right 05 Magazine Up Left 06 Magazine Up Right 07 Drive Manager

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 63 Error Type 5 Error Type defines the type of error and the action to which the event is related. This field helps identify what caused the event to occur. Table 10 Error Code Listing and Suggested Actions 08 Bar Code Reader 09 Front Panel 0A IP 0B Diagnostic 0C Error 0D Code Update 0E ADI 0F Drive Manager Timer 11 HTTP 12 SNTP 20 Idle 3E Watch Dog Timer 3F Un-handle Interrupt Error Description Suggested Actions 00–25 General Software flags • Check for a Hard Error log. If an error displays in the Hard Error log, power cycle the autoloader and run the Loader—Health Check test. • Check www.quantum.com for firmware updates. • If all previous steps fail, contact customer support. Task ID Description

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 64 26 Message Send ID error • Power cycle the autoloader. • If the previous step fails, contact customer support. 27 Message Bad • Check the SCSI bus cables and terminators. • Check the host adapter. • If all previous steps fail, contact customer support. 28 Message parameter Bad • Check the host device driver. • Check the host application. • Check the SCSI bus cables and terminators. • Check the host adapter. • Power cycle the autoloader. Repeat checks after power cycle. • If all previous steps fail, contact customer support. 29 Invalid Element • Check the host device driver. • Check the host application. • Power cycle the autoloader. Repeat checks after power cycle. • If all previous steps fail, contact customer support. 2A Invalid Element Status • Check the host device driver. • Check the host application. • Power cycle the autoloader. Repeat checks after power cycle. • If all previous steps fail, contact customer support. 2B–2F Firmware tables and stacks invalid • Check for a Hard Error log. If an error displays in the Hard Error log, power cycle the autoloader and run the Loader—Health Check test. • Check www.quantum.com for firmware updates. Error Description Suggested Actions

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 65 30 POST Failure • Verify that the magazines are fully seated. • Power cycle. • If all previous steps fail, contact customer support. 31–38 System Monitoring type events • Check for a Hard Error log. If an error displays in the Hard Error log, power cycle the autoloader and run the Loader—Health Check test. • Check www.quantum.com for firmware updates. • If all previous steps fail, contact customer support. 3A Drive Error • Check the Drive Log Sense for drive errors. If the drive is still logging errors, contact customer support. • If the drive is logging tray a different piece of media. • If the drive fails with two different pieces of media, contact customer support. 3B Drive Hardware Err 3C Drive Needs Cleaning 3D Drive Error • Check the Drive Log Sense for drive errors. If the drive is still logging errors, contact customer support. • If the drive is logging tray a different piece of media. • If the drive fails with two different pieces of media, contact customer support. 3E Load Error • Verify that the cartridge does not have labels or other matter anywhere on the cartridge except where labels are expected to be placed. • Try to load a different piece of media. • If multiple pieces of media fail, contact customer support. Error Description Suggested Actions

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 66 3F Unload Error • Verify that the cartridge does not have labels or other matter anywhere on the cartridge except where labels are expected to be placed. • Try to load a different piece of media. • If multiple pieces of media fail, contact customer support. 49 Offline • No action required. 4A Door Locked • No action required. 4B Open Front • Install the magazine or magazine blank. • Replace the magazine or magazine blank (try a second one if possible). • If all previous steps fail, contact customer support. 4C Over Temp • Verify that the temperature of the autoloader inlet air is within specifications. • Clear debris from any opening of the autoloader, both in front and in the back. • Verify that both fans are working. If fans are bad, contact customer support. 60–69 Internal communications events • Power cycle. • If the previous step fails, contact customer support. A0–A4 Picker Servo Errors • Run the Loader–Health Check test. • If repeated events display in the Hard Error log, power cycle the autoloader. Repeat test after power cycle. • If all previous steps fail, contact customer support. Error Description Suggested Actions

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 67 A5 Source Element Empty • Verify that the expected source really does have a cartridge. • Run the Loader–Health Check test. • If the source is a magazine, replace the cartridge in that slow with a different cartridge and try again. If error continues, replace the magazine. • If source is the tape drive, verify the tape drive has a cartridge and it was ejected. • Power cycle the autoloader. • If the error continues, contact customer support. A6 Source Magazine Missing • Verify that the magazine is installed correctly into the autoloader. • Remove and reinsert the magazine again. • Try a second magazine, if possible. • Power cycle the autoloader. • If the error continues, contact customer support. A7 Mailslot full • Verify that the magazine is installed correctly in the autoloader. • Remove and reinsert the magazine again. • Try a second magazine, if possible. • Power cycle the autoloader. • If all previous steps fail, contact customer support. Error Description Suggested Actions

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 68 A8 Destination Element Full • Verify the expected destination really does not have a cartridge. • Run the Loader—Health Check test. • If destination is a magazine, install and remove a cartridge from the selected slot and try again. If error continues, replace the magazine. • If destination is the tape drive, verify the tape drive does not have a cartridge. • Power cycle the autoloader. • If error continues, contact customer support. • If the cartridge is in the mailslot opening, remove it. • Verify that the mailslot is fully closed. • Verify that there is no debris in the mailslot opening. A9 Picker Full • Look in the front of the autoloader and confirm that the picker is full. • Run the Loader—Health Check test. • If all previous steps fail, contact customer support. AA Picker Cartridge Sensor Error • Look in the front of the autoloader and confirm the picker is full. • Run the Loader—Health Check test. • If all previous steps fail, contact customer support. AB Drive Path Sensor Error • Run the Loader—Health Check test. • Power cycle the autoloader. • If all previous steps fail, contact customer support. AC Mail Slot Door Sensor Error • Insert a cartridge into the autoloader via the mailslot. • Power cycle the autoloader. • If all previous steps fail, contact customer support. Error Description Suggested Actions

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 69 AD Mail Slot Solenoid Error • Insert a cartridge into the autoloader via the mailslot. • Power cycle the autoloader. • If all previous steps fail, contact customer support. AE Unknown Servo Error • Run the Loader—Health Check test. • If the previous step fails, contact customer support. AF Error Log Information Event • No action required. B0–BF Error Events related to the picker not rotating or translating properly • Run the Loader—Health Check test. • Power cycle the autoloader. • If all previous steps fail, contact customer support. C0 Unknown Motor Error • Run the Loader—Health Check test. • Power cycle the autoloader. • If all previous steps fail, contact customer support. D0 Magazine Solenoid Bad • Check the Task ID in the Hard Error log to determine if the problem is the right or the left magazine. • Remove and reinsert the magazine. Verify that the magazine slides freely, and clicks and locks into place. • Power cycle the autoloader. • Try a different magazine. • If all previous steps fail, contact customer support. D1 Magazine Present Sensor Bad • Check the Task ID in the Hard Error log to determine if the problem is the right or the left magazine. • Remove and reinsert the magazine. • Power cycle the autoloader. • Make sure that the sensor is not blocked by debris. • If all previous steps fail, contact customer support. Error Description Suggested Actions

Autoloader Troubleshooting Quantum SuperLoader 3A Series User’s Guide 70 D2–D4 Position Sensor Bad • Check the Task ID in the Hard Error log to determine if the problem is the right or the left magazine. • Remove and reinsert the magazine. • Try a different magazine, if possible. • Power cycle the autoloader. • If all previous steps fail, contact customer support. D5–DE Cartridge flags located on the magazine may be bad or the sensor to detect the flags may have a problem. • Check the Task ID in the Hard Error log to determine if the problem is the right or the left magazine. • Remove and reinsert the magazine. • Try a different magazine, if possible. • Make sure that the sensor is not blocked by debris. • Power cycle the autoloader. • If all previous steps fail, contact customer support DF Jammed Cartridge • Check the Task ID in the Hard Error log to determine if the problem is the right or the left magazine. • Power cycle the autoloader. • If all previous steps fail, contact customer support Error Description Suggested Actions

Power-on Self Test (POST) Quantum SuperLoader 3A Series User’s Guide 71 Power-on Self Test (POST) This section describes the POST and its various tests and also explains how to perform diagnostic tests from the front panel and from the On- board Remote Management interface. The Power-on Self Test (POST) and diagnostic tests are helpful tools for testing the autoloader’s functionality and for troubleshooting errors. With the results from the POST and diagnostic tests, you can determine how well the autoloader is working and locate any problems Every time you turn on the autoloader, the POST checks all of the autoloader’s basic components. If you experience problems with the autoloader, the POST is a good method to determine if any major parts are malfunctioning. . The autoloader recognizes when the drive or autoloader is executing host commands and will respond appropriately to prevent application failures. A diagnostic command issued between host application commands may not be recognized appropriately, resulting in a failed application. Table 11 POST Descriptions Note: Use of the Diagnostic Commands from the On-board Remote Management interface should not be issued while the autoloader is being used by host applications. Only use the Diagnostics Commands when the autoloader is known to be idle and unavailable to host backup/restore applications. POST Test Description MICROP Tests the microprocessor’s general-purpose registers IRAM Tests the microprocessor’s internal RAM Addr Lines Bit walks the SRAM address lines SRAM Tests the 512k SRAM

Power-on Self Test (POST) Quantum SuperLoader 3A Series User’s Guide 72 Performing a POST 5 If you experience errors while operating your autoloader, you may need to reboot the autoloader to perform a POST. To reboot the SuperLoader 3A Series: 1 Hold down the power button until the System Shutdown Please Wait... message displays. 2 Release the power button. The autoloader turns off. 3 Press the power button again to turn the autoloader on. POST runs automatically. Interpreting the POST Results 5 While the POST is running, a progress indicator showing the name of the test displays on the front panel. If the autoloader is working properly, the message System Ready and the current configuration display after the POST completes successfully. If the autoloader is not working properly, error messages display on the front panel (see Autoloader Troubleshooting on page 58). Code Chksum Verifies the Flash image checksum EERom Checks the EERom area and verifies the checksums PLL Clock Tests that the microprocessor’s PLL is synchronized correctly LCD Verifies that the LCD is present and working correctly Ethernet Configures and verifies communication with the Ethernet chip Barcode Verifies that the bar code reader is present and performs a hardware handshake Temperature Sense Pass/Fails the MDM and configures the AHIM temperature sensors MDM Verifies that the MDM is present and checks the sensors Fan Verifies that the fan is operating correctly POST Test Description

Diagnostic Tests from the Front Panel Quantum SuperLoader 3A Series User’s Guide 73 Diagnostic Tests from the Front Panel Diagnostic tests allow you to calibrate parts of the autoloader, check the condition of parts, or test the autoloader’s functionality. From the front panel, you can perform all of the diagnostic tests. Because certain tests require you to manually insert a cartridge, you can perform only some of the diagnostic tests using On-board Remote Management (see On-board Remote Management Diagnostic Tests). Setting the Security 5 When you enable the security function, the diagnostic tests are password protected to ensure data integrity. To access any of the diagnostic tests, you must first enter an Administrator password. If you do not enter the password, you will be prompted to enter the password when you attempt to perform a diagnostic test. To enter an Administrator password: 1 From any menu, click the Commands heading. The Commands screen displays. 2 On the Command submenu, scroll to Enter Password, and then press Enter. 3 On the Enter Password submenu, scroll to Administrator, and then press Enter. The Login screen displays with a row of asterisks. A text box displays above the first asterisk. 4 In the text box, scroll to the first number of the password, and then press Enter. The text box above the asterisk disappears and another text box displays above the next asterisk. 5 Repeat step 4 to enter the remaining numbers of your password. Note: On-board Remote Management allows you to request all diagnostic tests, but any tests that require a cartridge to be inserted will time-out unless someone manually inserts the cartridge at the appropriate time. Note: Press Escape to backspace to a previous text box, if necessary.

Diagnostic Tests from the Front Panel Quantum SuperLoader 3A Series User’s Guide 74 When you have finished entering your password, Submit Password displays on the LCD below the asterisks. 6 Press Enter to submit your password. The display returns to the Enter Password submenu. Stopping a Diagnostic Test 5 At times you may need to stop a diagnostic test while it is in progress. Certain diagnostic tests even require you to stop them or they run continuously. To stop a diagnostic test while it is running, use the Halt Test function. When you select Halt Test, any picker or magazine functions complete, and then the diagnostic test is stopped. To perform a Halt Test from the front panel: 1 While the diagnostic test you wish to stop is running, press Escape. The Diagnostics submenu displays. 2 On the submenu, scroll to Halt Test, and then press Enter. User Abort displays. 3 Press Enter to return to the Diagnostics submenu. Refer to On-board Remote Management for any test results. To perform a Halt Test from On-board Remote Management: 1 Select Halt Test from the Diagnostics drop-down menu, and click Stop Test. 2 Select View Status to see the results of the command. Test Stopped displays along with any test results. Front Panel Diagnostic Tests 5 You can perform the following diagnostic tests using the front panel: • Halt Test • Loader—Self Test • Loader—Health Check • Loader—Picker Test • Loader—Magazine Test • Loader—Inventory Test • Sales Demo (performs a Random Access Load/Unload sequence) • RALU Logs (displays the results from the previously run Sales Demo)

Diagnostic Tests from the Front Panel Quantum SuperLoader 3A Series User’s Guide 75 To perform any of the front panel diagnostic tests: 1 From the main menu, scroll to Diagnostics and press Enter. 2 Scroll to the test that you want to run and press Enter. If you are already logged in as Administrator, the test begins executing immediately. The message Running Test displays while the test is running. The Loader—Health Check test displays an ongoing progress indicator while executing. When the test completes, either the message Test Successful displays or the message Test Failed and an error code displays. Proceed to step 4. 3 If you are not logged in, you will be asked to enter the Administrator password. Do the following: a From the front panel, enter the Administrator password by using the Up and Down scroll arrows to select each digit, and then press Enter to move to the next digit. To move to the previous digit, press Escape. When you have entered the entire six digit password, you will be asked to press Enter one more time to submit the password. If the password is incorrect, you will be asked to re-enter it using the same procedure. Otherwise, you will be returned to the Diagnostics menu. Press Enter to run the desired test. Running Test displays while the test is in progress. To stop the test prematurely, see Stopping a Diagnostic Test. b The Loader—Health Check test displays an ongoing progress indicator while executing. When the test completes, either the message Test Successful displays or the message Test Failed and an error code display. 4 If the test is successful, press Enter to return to the Diagnostics test menu. For detailed results of a test, use On-board Remote Management to retrieve the diagnostic test status (see Diagnostics Using On-board Remote Management).

On-board Remote Management Diagnostic Tests Quantum SuperLoader 3A Series User’s Guide 76 On-board Remote Management Diagnostic Tests You can perform the following diagnostic tests from On-board Remote Management: • Halt Test • Loader—Self Test • Loader—Health Check • Loader—Picker Test • Loader—Magazine Test • Loader—Inventory Test Diagnostics Using On- board Remote Management 5 Many tests can be run using On-board Remote Management. To perform On-board Remote Management diagnostic tests: 1 Open a web browser and connect to the autoloader. The On-board Remote Management main menu displays. 2 Click the Diagnostics heading. A login window displays. 3 Type an Administrator user name and a password, and then click Enter. The Diagnostics submenu displays. 4 Select the test you wish to perform from the Diagnostics drop-down menu, and then click Start Test. The selected diagnostic test runs. While the test is running, you can view the status of the test. To view the status from the View Diagnostic Test Progress, click View Status. Note: On-board Remote Management allows you to request all diagnostic tests, but any tests that require a cartridge to be inserted will time-out unless someone manually inserts the cartridge at the appropriate time.

Returning the Autoloader for Service Quantum SuperLoader 3A Series User’s Guide 77 Returning the Autoloader for Service If you need to return the autoloader to the factory for service, first verify which customer replaceable unit (CRU) that you need to return and return only that CRU, not the entire autoloader. Once you determine the CRU to replace, contact customer support to obtain return authorization (RA) and shipping information. When you have the RA number, use the following procedure. Preparing the Autoloader for Shipment 5 If you must return the complete autoloader for service, use these steps to prepare the autoloader for shipment. 1 Remove all cartridges from the unit. 2 Power off the autoloader via the front panel. 3 Remove the power and Ethernet cables from the autoloader. Removing the Autoloader from a Rack 5 To remove the autoloader from a rack: 1 Loosen the four screws that connect the two support brackets to the two autoloader brackets. 2 Loosen the four screws on the front of the autoloader that attach the two front tabs (support brackets) to the front rails. Do not remove the screws completely at this time. 3 Remove the four screws at the back of the autoloader that connect the support brackets (two screws per bracket) to the autoloader brackets. 4 While supporting the front of the autoloader, remove the four front screws. Note: Do not ship these items if you are returning the autoloader to the factory. Caution: Injury may occur if the unit is not supported when you remove the front screws. The screws are holding up the front of the unit.

Returning the Autoloader for Service Quantum SuperLoader 3A Series User’s Guide 78 5 Using two people, or an appropriately rated mechanical lift, remove the autoloader from the rack by sliding the autoloader out and supporting it from the bottom. The person handling the back of the unit must depress the locking tab on the support bracket while sliding the unit forward. 6 Loosen the four screws and remove the autoloader brackets from the back of the autoloader. 7 Place the autoloader into the original packaging box. If you no longer have the original packaging, contact your service representative to purchase the packaging kit. Packing the Autoloader 5 Use the original packing material to pack the autoloader: the shipping container, two foam insert packing pieces, the accessory kit box (or the filler tube if your autoloader did not come with an accessory kit box), and the antistatic bag. You will also need packing tape. 1 Place the antistatic bag over the autoloader. 2 Place one of the foam endcaps onto one side of the autoloader. Place the second foam insert onto the other side of the autoloader and make sure the pieces fit snugly onto the autoloader. 3 Place the autoloader down into the shipping box and push the back of the autoloader towards the back end of the box. 4 Insert the empty accessory kit box (or filler tube) into the shipping box at the front end of the autoloader in the space between the autoloader foam inserts and the shipping container. 5 Place any necessary paperwork on top of the autoloader inside the box. 6 Close and seal the box. 7 Place the shipping label on the box. 8 Ship the box. Note: One end of the foam insert has a curved piece. This end of the foam insert is designed to fit the front of the autoloader.

79 Appendix A ASpecifications This appendix provides specifications for the SuperLoader 3A Series autoloader equipped with an A-Series tape drive. • SuperLoader 3A Series Autoloader • A-Series SDLT 600A Tape Drive • A-Series LTO-3A Tape Drive

SuperLoader 3A Series Autoloader Quantum SuperLoader 3A Series User’s Guide 80 SuperLoader 3A Series Autoloader Physical Specifications 1 Performance Specifications 1 Rack Mount Height 8.9 cm (3.5 in.) Width 45 cm (17.7 in.) Length 75.46 cm (29.71 in.) Package Weight (without media) 22.7 kg (50 lb.) Footprint 0.32 square meters (3.4 square feet) Drive Type 1 Quantum A-Series tape drive MCBF 400,000 cycles Typical cycle time < 40 seconds. One cycle consists of moving a cartridge from the tape drive to a magazine slot, selecting another magazine slot, and then moving the cartridge back to the tape drive. It does not include the time that the tape drive takes to unload or load/calibrate.

SuperLoader 3A Series Autoloader Quantum SuperLoader 3A Series User’s Guide 81 Environmental Specifications 1 Temperature Range (Dry Bulb) Operating +10º to +35ºC Nonoperating - 40ºC to +65ºC Temperature Variation Operating 10ºC per hour Nonoperating 20ºC per hour Humidity Operating 20% to 80% noncondensing Nonoperating 10% to 90% noncondensing Gradient 10% per hour without condensation Wet Bulb Operating 26ºC max Nonoperating 29ºC max Altitude Operating -153 m to 3048 m Nonoperating -153 m to 12192 m

SuperLoader 3A Series Autoloader Quantum SuperLoader 3A Series User’s Guide 82 Power Specifications 1 Vibration Specifications 1 Shock Specifications 1 Line voltage 60 Hz system: 90–265 VAC; 50 Hz system: 90–265 VAC Maximum power 160W Line frequency 47–63 Hz AC Input current 60 Hz system: 4.0 A (RMS) for 115 VAC 50 Hz system: 2.0 A (RMS) for 230 VAC Operating Swept Sine Vibration 5–500 Hz, 0.25 G, 0.254 mm (0.01 in.) to smooth crossover, 1 8ve/min, (X, Y, Z) axes Random Vibration 0.25 Grms, 5–500 Hz (X, Y, Z) axes Non-Operating Swept Sine Vibration 5–500 Hz, 0.75 G, 0.52 mm (0.02 in.) to smooth crossover, 1 8ve/min, (X, Y, Z) axes Random Vibration 1.06 Grms, 5–500 Hz (X, Y, Z) axes Operating 3 G, 5 ms half-sine, 3 pulses (+/-) per axis, X, Y, Z Non-Operating 20 G, 8 ms half-sine, 3 shocks (+/-) per axis, X, Y, Z

A-Series SDLT 600A Tape Drive Quantum SuperLoader 3A Series User’s Guide 83 A-Series SDLT 600A Tape Drive Drive Specifications 1 Media Capacity 1 Media Specifications 1 Description Quantum SDLT 600A Read/write transfer rate: maximum sustained (SDLT II media) Noncompressed mode: 129.6 GB/hr Compressed (2:1 typical): 259.2 GB/hr Burst transfer rate 160 MB/s Average access time 79 seconds (from BOT) Loading time to BOT (for previously written tape) 40 seconds (maximum) Unloading time from BOT 20 seconds (maximum) Interface type Gigabit Ethernet (GigE) Media Type Capacity SDLT II storage capacity 4.7 TB (noncompressed) with 16 cartridges 9.4 TB (2:1 typical compression) with 16 cartridges Characteristic SDLT II SDLT II formatted capacity 300 GB (noncompressed) 600 GB (2:1 typical compression) Basic description Advanced metal particle

A-Series SDLT 600A Tape Drive Quantum SuperLoader 3A Series User’s Guide 84 Tape length 630 m (2,066 ft.) Cartridge dimensions 105.6 x 105.3 x 25.4 mm (4.16 x 4.15 x 1.0 in) Read compatibility SDLT I, SDLT II Shelf life > 30 years with < 10% loss in demagnetization @ 20°C 40% RH (noncondensing) Cartridge life 1,000,000 passes (any point on the tape passing the recording head in either direction) SDLT Cleaning cartridge life 15 uses Characteristic SDLT II

A-Series LTO-3A Tape Drive Quantum SuperLoader 3A Series User’s Guide 85 A-Series LTO-3A Tape Drive Drive Specifications 1 Media Capacity 1 Description Quantum LTO-3A Read/write transfer rate: maximum sustained (LTO Ultrium 3 media) Noncompressed mode: 68 MB/s Compressed (2:1 typical): 136 MB/s Burst transfer rate 160 MB/s (maximum, native) Average access time 58 seconds (from BOT) Loading time to BOT (for previously written tape) 75 seconds (maximum) Unloading time from BOT 30 seconds (maximum) Interface type Gigabit Ethernet (GigE) Media Type Capacity LTO Ultrium 3 storage capacity 6.4 TB with 16 cartridges 12.8 TB (2:1 typical compression) with 16 cartridges

A-Series LTO-3A Tape Drive Quantum SuperLoader 3A Series User’s Guide 86 Media Specifications 1 Characteristic LTO Ultrium 3 LTO Ultrium 3 formatted capacity 400 GB (noncompressed) 800 GB (2:1 typical compression) Basic description Pre-formatted (servo written) metal particle Tape length 680 m (2230.9 ft.) Cartridge dimensions 102 x 105.4 x 21.5 mm (4 x 4.15 x .85 in) Read compatibility LTO Ultrium 1, LTO Ultrium 2, LTO Ultrium 3 Write compatibility LTO Ultrium 2, LTO Ultrium 3 Shelf life > 30 years with < 10% loss in demagnetization @ 20°C 40% RH (noncondensing) Cartridge life 1,000,000 passes (any point on the tape passing the recording head in either direction) LTO Universal Cleaning cartridge life 20 uses