Sennheiser EM 100 G3 Specifications

42 MHz bandwidth: 1680 tunable UHF frequencies for interference-free reception Enhanced frequency bank system with up to 12 compatible frequencies High-quality true diversity reception Pilot tone squelch for eliminating RF inter- ference when transmitter is turned off Automatic frequency scan feature searches for available frequencies Enhanced AF frequency range Wireless synchronization of transmitters via infrared interface User-friendly menu operation with more control options Illuminated graphic display Auto-Lock function avoids accidental changing of settings HDX compander for crystal-clear sound Receiver features transmitter battery indicatation in 4 steps Integrated Equalizer, Soundcheck mode and guitar tuner Wide range of accessories adapts the system to any requirement Optimized PLL synthesizer and micropro- cessor technology With its improved design and new features, this rugged G3 rack receiver is ready for the road with its proven transmission reliability and inspiring flexibility. The sound check mode allows you to check the audio and RF signal at any time during setup. 20 frequency banks with 12 preset frequencies each, plus a user-program- mable bank mean you can easily run multiple channels of G3 wireless simultane- ously. TECHNICAL DATA Modulation................................................................wideband FM Frequency ranges....................................................516 – 558, 566 – 608, 626 – 668, 734 –776, 780 – 822, 823 – 865 MHz Receiving frequencies.............................................1,680 frequencies, tuneable in steps of 25 kHz 20 frequency banks, each with up to 12 factory-preset channels, intermodulation-free 1 frequency bank with up to 12 user programmable channels Switching bandwidth..............................................42 MHz Nominal/peak deviation........................................± 24 kHz/± 48 kHz Receiver principle.....................................................true diversity Sensitivity (with HDX, peak deviation)..............< 2 μV for 52 dBA rms S/N Adjacent channel rejection....................................typ. ≥ 65 dB Intermodulation attenuation................................typ. ≥ 65 dB Blocking......................................................................≥ 70 dB Squelch.......................................................................Off, Low: 5 dBmV, Middle: 15 dBmV, High: 25 dBmV Pilot tone squelch....................................................can be switched off Antenna inputs........................................................2 BNC sockets Compander system..................................................Sennheiser HDX EQ presets Preset 1: “Flat” Preset 2: “Low Cut”.................................................−3 dB at 180 Hz Preset 3: “Low Cut/High boost”...........................−3 dB at 180 Hz +6 dB at 10 kHz Continued on page 2 EM 100 G3 Stationary receiver

TECHNICAL DATA Preset 4: “High Boost”...............................................+6 dB at 10 kHz S/N ratio (1 mV, peak deviation)............................≥110 dBA THD.................................................................................≤ 0.9% AF output voltage (at peak deviation, 1 kHz AF) ¼” (6.3 mm) jack socket (unbalanced)................+12 dBu XLR socket (balanced)...............................................+18 dBu Adjustment range of audio output level...............48 dB, adjustable in steps of 3 dB +6 dB gain reserve Temperature range.....................................................−10 °C to + 55 °C Power supply...............................................................12 V Nominal voltage..........................................................2.4 V DC Power consumption...................................................300 mA Dimensions...................................................................approx. 190 mm x 212 mm x 43 mm Weight...........................................................................approx. 980 g ARCHITECT’S SPECIFICATIONS The stationary receiver with true diversity technology shall be for use with a companion transmitter as part of a wireless RF trans- mission system. The receiver shall operate within six UHF frequency ranges, each with a 42 MHz switching bandwidth: 516 – 558 MHz, 566 – 608 MHz, 626 – 668 MHz, 734 –776 MHz, 780 – 822 MHz, 823 – 865 MHz; receiving frequencies shall be 1,680 per range and shall be tunable in 25 kHz steps. The receiver shall feature 20 fixed frequency banks with up to 12 compatible frequency presets and 1 user bank with up to 12 user programmable frequencies. The receiver shall feature a balanced XLR-3M audio output with a maximum output of +18 dBu along with an unbalanced 1⁄4“ (6.3 mm) audio output with a maximum output of +12 dBu. Two BNC-type input sockets shall be provided for connecting the antennas. The receiver shall be menu-driven with a backlit LC display showing the current frequency, frequency bank and channel number, metering of RF level, metering of AF level, lock status, pilot tone evaluation, muting function, and battery status of the associated transmitter. An auto-lock feature shall be provided to prevent settings from being accidentally altered. The receiver shall feature an integrated guitar tuner and shall provide a sound check mode. Some receiver parameters such as receiving frequency, receiver name and pilot tone setting shall be synchronizable with the associated transmitter via an integrated infrared interface. Nominal/peak deviation shall be ±24 kHz/±48 kHz. Squelch threshold shall be defeatable (off) or adjustable to three levels: Low (5 dBμV), Middle (15 dBμV) and High (25 dBμV). The receiver shall incorporate the Sennheiser HDX compander system and a defeatable pilot tone squelch. Sensitivity shall be < 2 μV for 52 dBArms S/N with HDX engaged at peak deviation. Adjacent channel rejection shall be ≥ 65 dB (typical). Intermodu­ lation attenuation shall be ≥ 65 dB (typical); blocking shall be ≥ 70 dB. Four selectable equalizer presets shall be provided: “Flat”, “Low Cut” (−3 dB at 180 Hz), “Low Cut/High Boost” (−3 dB at 180 Hz/+6 dB at 10 kHz) and “High Boost” (/+6 dB at 10 kHz). Signal-to-noise ratio at 1 mV and peak deviation shall be ≥ 110 dB. Total harmonic distortion (THD) shall be ≤ 0.9 %. The audio output level shall be adjustable within a 48 dB range in steps of 3 dB. The receiver shall operate on 12 V power supplied from the NT 2-1 mains unit (for 110 V AC or 230 V AC, 50/60 Hz) or the NT 2-3 mains unit (for 100 – 240 V AC, 50/60 Hz). Power consumption shall be 300 mA. The receiver shall have a rugged metal housing; dimensions shall be approximately 190 x 212 x 43 mm (7.48“ x 8.35“ x 1.69“). Weight shall be approximately 980 grams (2.16 lbs). Operating temperature shall range from −10 °C to +55 °C (+14 °F to +131 °F). The receiver shall be the Sennheiser EM 100 G3. Delivery includes 1 EM 100 G3 stationary receiver 1 NT 2-3 or NT 2-1 mains unit with one country adapter 2 Rod antennas 2 Stacking elements 1 Instruction manual 1 Frequency information sheet 4 Device feet

Power supply unit EU Cat. No. 503124 EM 100 G3-A-US – 516...558 MHz / Power supply unit US Cat. No. 503512 EM 100 G3-A-UK – 516...558 MHz / Power supply unit UK Cat. No. 503513 EM 100 G3-G-EU – 566...608 MHz / Power supply unit EU Cat. No. 503514 EM 100 G3-G-US – 566...608 MHz / Power supply unit US Cat. No. 503515 EM 100 G3-G-UK – 566...608 MHz / Power supply unit UK Cat. No. 503516 EM 100 G3-B-EU – 626...668 MHz / Power supply unit EU Cat. No. 503517 EM 100 G3-B-US – 626...668 MHz / Power supply unit US Cat. No. 503518 EM 100 G3-B-UK – 626...668 MHz / Power supply unit UK Cat. No. 503519 EM 100 G3-C-EU – 734...776 MHz / Power supply unit EU Cat. No. 503520 EM 100 G3-C-US – 734...776 MHz / Power supply unit US Cat. No. 503521 EM 100 G3-C-UK – 734...776 MHz / Power supply unit UK Cat. No. 503522 EM 100 G3-D-EU – 780...822 MHz / Power supply unit EU Cat. No. 503523 EM 100 G3-D-EU-X – 780...822 MHz / Power supply unit EU/Germany Cat. No. 503524 EM 100 G3-D-UK – 780...822 MHz / Power supply unit UK Cat. No. 503525 EM 100 G3-E-EU – 823...865 MHz / Power supply unit EU Cat. No. 503526 EM 100 G3-E-EU-X – 823...865 MHz / Power supply unit EU/Germany Cat. No. 503527 EM 100 G3-E-UK - 823...865 MHz / Power supply unit UK Cat. No. 503528 EM 100 G3-1G8 – 1785 MHz...1800 MHz Cat. No. 504909 RECOMMENDED ACCESSORIES AM 2 – Antenna Mount Cat. No. 9912 CC 3 – Case Cat. No. 503168 L 2015 – Charging Adapter Cat. No. 9828 BA 2015 – Akku Cat. No. 9950 AC 3 – Active antenna combiner Cat. No. 503166 ASA 1 – Antenna spiltter Cat. No. 503165 ASA 1-1G8 – Antenna spiltter Cat. No. 504914 NT-1 – plug-in mains unit for ASA 1 & L 2015 Cat. No. 4786 CL 2 – Linecable Cat. No. 4840 A 1031-U – Antenna Cat. No. 4645 AD 1800 – Antenna Cat. No. 504916 AB 3 – Antennabooster Cat. No. 21822 AB 3 – 1G8 Antennebooster Cat. No. 504915 GA 3 19“ Rack Adapter Cat. No. 503167 NT 2-3-US – Power supply for G3 EM rackmount receivers and transmitters Cat. No. 503870 GA 3 19“ Rack Adapter Cat. No. 503167 AM 2 – Antenna Mount Cat. No. 9912 ASA 1 – Antenna spiltter Cat. No. 503165 NT 1-1 EU – Mains unit for powering the ASA 1 antenna splitter or the L 2015 charger, EU version Cat. No. 503158 NT 1-1 US – Mains unit for powering the ASA 1 antenna splitter or the L 2015 charger, 120 V version Cat. No. 503873 NT 1-1 UK – Mains unit for powering the ASA 1 antenna splitter or the L 2015 charger, UK version Cat. No. 503874 NT 2-3 EU – Mains unit for powering the EM 100 G3 stationary receiver, EU version Cat. No. 503157 NT 2-3 US – Mains unit for powering the EM 100 G3 stationary receiver, 120 V version Cat. No. 503870 NT 2-3 UK – Mains unit for powering the EM 100 G3 stationary receiver, UK version Cat. No. 503871 Sennheiser electronic GmbH & Co. KG Am Labor 1, 30900 Wedemark, Germany www.sennheiser.com 03/13  Sennheiser is a registered trademark of Sennheiser electronic GmbH & Co. KG. www.sennheiser.com.  Copyright © 03/2013. All rights reserved. Errors and omissions excepted. EM 100 G3 Stationary receiver