Radio Shack 63-984 Operation & User’s Manual

All Rights Reserved. RadioShack is a registered trademark used by Tandy Corporation. Cat. No. 63-984 Wireless Intercom Door Chime Your RadioShack Wireless Intercom Door Chime operates as a two-tone doorbell and an intercom. The chime is simple to install because it requires no wiring. Your chime's two channel switch and digital coding prevent other transmitters or radio devices from sounding the chime. To conserve power, both the receiver and transmit- ter automatically turn off 30 seconds after you stop using them. The chime includes these features: Separate Buttons for Bell and Inter- com — let your callers first announce their arrival and then communicate us- ing the intercom. Receiver Volume Control — lets you adjust the volume to a comfortable lev- el. 2-Channel Transmitter and Receiv- er with Digital Code Selection — as- sure interference-free communication. 50-Foot Usable Operation Distance — means you can install the transmit- ter and receiver virtually anywhere in your home or business. Indicators — light so you can easily confirm the chime’s operation. WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SERVICE- ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. This symbol is intended to alert you to the presence of uninsu- lated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to con- stitute a risk of electric shock. Do not open the product’s case. This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accom- panying this product. ! ! 63-984.fm Page 1 Wednesday, September 8, 1999 4:42 PM

The transmitter and receiver are equipped with two selectable operation channels and two selectable digital codes, to ensure positive operation and prevent interference from similar prod- ucts nearby. Select the same channel and code number for both the transmit- ter and the receiver. To set the channel, slide CHANNEL A/B on the side of the receiver to A or B, then set the transmitter’s channel switch (shown here) to the same setting. Note: If the door chime occasionally sounds without anyone pressing BELL on the transmitter, change the channel settings. To set the code, remove the battery compartment cover and slide CODE to either 1 or 2 on the receiver, then set the transmitter’s code switch to the same setting. Connecting the Receiver to AC Power Locate a standard AC outlet in the area where you want to hear the chime and use the intercom. Plug the receiver's power cord into the outlet. POWER lights. Installing the Transmitter's Batteries The transmitter uses four AA batteries (not supplied) for power. For the best performance and longest life, we recom- mend RadioShack alkaline batteries. Cautions: • Use only fresh batteries of the re- quired size and recommended type. • Do not mix old and new batteries, different types of batteries (stan- dard, alkaline, or rechargeable), or rechargeable batteries of different capacities. Follow these steps to install batteries. 1. Use a flat blade screwdriver to loosen the screw in the transmitter’s battery compartment cover, then lift the cover off. Channel Code 63-984.fm Page 2 Wednesday, September 8, 1999 4:42 PM

compartment as indicated by the polarity symbols (+ and –) marked inside. 3. Be sure the rubber seal around the battery compartment is properly positioned, then replace the cover and tighten the screw. Replace all four batteries if the transmit- ter’s indicator lights dimly or not at all when you press any button on the trans- mitter. Warning: Dispose of old batteries promptly and properly. Do not burn or bury them. Caution: If you do not plan to use the door chime for a two week period, re- move the batteries. Batteries can leak chemicals that can destroy electronic parts. Testing the Chime Before permanently mounting the chime, follow these steps to test the sys- tem 1. With the receiver plugged into a standard AC outlet, adjust VOLUME to its middle position. Then press BELL on the transmitter. The chime should sound. 2. If the chime does not sound, make certain that the transmitter and re- ceiver are set to the same channel and code. 3. Adjust VOLUME on the receiver to the desired listening level. Mounting the Transmitter Mount the transmitter within 50 feet of the receiver using the supplied mounting hardware. Depending upon the mount- ing surface material of your home (wood siding, brick face, and so on), you might need to consult your local hardware store for a different type of mounting hardware. Note: While the transmitter is water- resistant, it is not waterproof. If you are mounting the transmitter out- doors, select a location that provides some shielding from the elements. Follow these steps to mount the trans- mitter. 1. Drill four 3/16-inch diameter holes into the mounting surface (as shown be- BELL 63-984.fm Page 3 Wednesday, September 8, 1999 4:42 PM

each hole. 2. Align the metal mounting bracket with the holes you just drilled and drive a screw through the bracket into each hole. Do not overtighten the screws. 3. Align the slot on the back of the transmitter with the hook on the mounting bracket. Carefully push the transmitter onto the hook and slide it down to secure it. 4. Once the transmitter is securely on the bracket, insert the two supplied pan-head machine screws through the two holes on the lower edge of the transmitter and into the threaded holes in the bracket. Mounting the Receiver To mount the receiver onto a typical sheetrock wall, use the two supplied pan washer screws and anchors. Other- wise, consult your local hardware store for suitable hardware. 1. Drill two 3/16-inch diameter holes into the mounting surface about 43/16 inches (106 mm) apart 2. Insert an anchor into each drilled hole, then thread a screw into each anchor, letting the head of each screw extend about 1/8 inch from the wall. 3/16 Inch Diameter Hole 50mm 85mm 1/8 Inch 63-984.fm Page 4 Wednesday, September 8, 1999 4:42 PM

the tabs on either side of the chan- nel on the back of the receiver 4. Align the receiver's keyhole slots with the screw heads and slide the receiver down to secure it. OPERATION Your caller presses BELL on the door transmitter to sound the receiver’s chime. Note: If the chime sounds when the transmitter's button is not pressed, change the channel settings on both the receiver and transmitter. Hold down TALK on the receiver (the red indicator lights) and speak in a normal tone into the transmitter’s microphone from about 2–3 inches away. When you release TALK, the caller can reply by holding down TALK on the transmitter. Notes: • The receiver and transmitter auto- matically turn off if no one presses a button within about 30 seconds. Pressing any button on either unit turns on the power again. • If the temperature approaches the lower end of the intercom’s operat- ing range (around 0°F), you might notice some sound distortion. This is not a malfunction. • A wireless telephone operating at 49MHz can interfere with the sys- tem. CARE To use your RadioShack Wireless Inter- com Door Chime system for a long time: • Keep the system dry. If it gets wet, wipe it dry immediately. • Use and store the system only in normal temperature environments. • Handle the system gently and care- fully. Do not drop either component. • Keep the system away from dust and dirt, and wipe the system with a damp cloth occasionally to keep it looking new. Modifying or tampering with the sys- tem’s internal components can cause a malfunction and invalidate its warranty. If your system is not performing as it should, take it to your local RadioShack store for assistance. THE FCC WANTS YOU TO KNOW Your chime system might cause TV or radio interference even when it is oper- ating properly. To determine whether the system is causing the interference, remove the transmitter’s battery or un- plug the receiver from AC power. If the interference goes away, the transmitter or the receiver is causing the interfer- ence. Try to eliminate the interference by moving the TV or radio away from the transmitter or contacting your local Ra- dioShack store for help. If you cannot eliminate the interference, the FCC re- quires that you stop using the system. 63-984.fm Page 5 Wednesday, September 8, 1999 4:42 PM