Digi MIL-02F Installation Manual

MIL•02F Fiber•MAU FDX Full-Duplex Fiber Optic Transceiver Installation Guide With LinkSentry™ Ethernet/IEEE 802.3 This guide includes the following information: “Introduction” on page 2 “Installation” on page 2 “Configuration” on page 2 “DIP Switch” on page 2 “Jumper Settings” on page 3 “Diagnostic LEDs and Conditions Indicated” on page 3 “Legal” on page 4 FIBER•MAU Model: MIL•02F ETHERNET FULL-DUPLEX 10BASE-FL TRANSCEIVER Power Required: 12 VDC 200 ma FCC PART 15 CLASS A COMPLIANT CX TX RX PWR LINK TX RX

with diagnostic LEDs, an AUI male connector, and either an SC- or ST-type fiber connector. Installation 1. Connect the fiber cables: Attach the fiber cables from the fiber network cabling to the fiber connectors on the MIL-02F. 2. Attach the 15-pin AUI connector from the MIL-02F to the DB-15 connector on the device you wish to connect to. 3. Tighten the latch screws to secure the unit. 4. Restart the computer. The PWR LED illuminates. Note: If the PWR LED did not illuminate, reinstall the MIL-02F. If it still does not illuminate, contact our technical support department. Configuration The MIL-02F comes with configurable options, which include a 2-position DIP switch and a 3-pin jumper. The DIP switch is located on left-side of MIL-02F (while facing the device), and the jumper is located inside the device. To open the MIL-02F to access the 3-pin jumper: 1. For device's with ST-type connectors,u nscrew the two hex nuts that secure the ST-type connectors. 2. Slide the top-half of the enclosure off, over the fiber connectors. The jumper is located on right-hand side of the device (Figure 1). DIP Switch The Link Sentry feature on the MIL-02F is configured through the 2-position DIP switch located on the side of the transceiver. Use a mechanical pencil to adjust the DIP switches. LinkSentry transmits link pulses only if the receive side of the link is seen. This allows fault-tolerant transceivers and hubs to detect faulty cables or bad equipment. Settings for the DIP switch includes: Table 1: DIP Switch Settings Up (off) Down (on) Switch 1 LinkSentry disabled (Default) LinkSentry enabled Switch 2 SQE disabled (Default) SQE enabled

• When pins 1 and 2 are covered, full-duplex is selected • When pins 2 and 3 are covered, half-duplex is selected (default) Figure 1.Inside the MIL-02F Diagnostic LEDs and Conditions Indicated • PWR (Power): Device is receiving power. • TX (Transmit): Packets are being transmitted over the network. • CX (Collision): Collisions are occurring on the network. • RX (Receive): Packets are being received from the network. • LINK (Link): The fiber optic link is good. DIP Switch 3-Pin jumper (with a jumper block installed)

Legal Regulatory Approvals • FCC Class A • UL 1950 • CSA 22 No. 950 • EN60950 • CE – EN55022 Class B – EN50082-1 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these directives implies conformity to the following European Norms: • EN55022 (CISPR 22) - Radio Frequency Interference • EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity • EN60950 (IEC950) - Product Safety To Contact Digi For prompt response when calling for service information, have the following information ready: • Product serial number and rev. • Date of purchase • Vendor or place of purchase Reach Digi Technical Support at 408/744-2751 Or E-mail at “[email protected]” Address: 1299 Orleans Drive Sunnyvale, CA 94089 Voice: 408/744-2775 Fax: 408/744-2793 E-mail: [email protected] Five-Year Limited Warranty Digi International warrants to the original consumer or purchaser that each of its products, and all components thereof, will be free from defects in material and/or workmanship for a period of five years from the original factory shipment date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable. Digi makes no express or implied warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall Digi be liable for incidental or consequential damages, costs, or expenses arising out of or in connection with the performance of the product delivered hereunder. Digi will in no case cover damages arising out of the product being used in a negligent fashion or manner.