RCA RT2770 Quick Start Manual

Please read these instructions for quick tips on using the unit. Setting up 1. Connecting the Speakers • Six speakers are provided with the unit: • 2 front speakers • 1 center speaker • 2 rear speakers • 1 subwoofer. • Speaker wires are color-coded to match the terminals. • Connect the speaker wire to the corresponding color terminal as shown below. • Press down the tab to open the terminal, insert the wire and release the tab. • When connecting subwoofer, connect subwoofer control cable (red/black striped) at the back of the subwoofer to the subwoofer control jack on the unit’s rear panel, then press POWER ON/OFF on the subwoofer speaker to turn it on. SUBWOOFER CONTROL Remote Control Tocom 56416640 (EN) QuickStartGuide 2 3 4 9 12 15 19 1 5 6 7 8 10 11 14 13 16 17 18 Use this jack on the rear panel to connect to the subwoofer control cable (red/black striped) of the subwoofer. Use this jack on the rear panel to connect another active subwoofer other than the one supplied. SUBWOOFER AUDIO OUT Center Speaker Front Speakers Right Left Right Left Rear speakers (Surround Sound) Subwoofer White/grey or black striped Red/grey or black striped Green/grey or black striped Purple/grey or black striped Blue/grey or black striped Grey/black striped 1. Turn on/off the unit 2. Directly access a preset station in AM/FM mode 3. Store station in AM/FM mode 4. Select between Stereo and Mono sound in FM mode 5. Test the loudness of the speakers. Refer to “Advanced Sound Control” for details 6. Select among night mode options (DRC OFF, SOFT and ON) which compresses the volume difference between normal voices and sounds such as explosions (Available only during Dolby digital signal playback) 7. Select among preset equalizer mode (FLAT, POP, JAZZ, ROCK, CLASSIC, BASS and TREBLE). • Adjust bass or treble level 8. Select among digital sound processor (STEREO, HALL, CHURCH, CLUB, STADIUM, STUDIO, 3 STEREO, DOLBY PL EMULATION, DOLBY PL II MUSIC and DOLBY PL II MOVIE) 9. Enter setup mode 10. Adjust the speakers’ distance 11. Select among setting items in setup mode • Adjust the values when the display shows the setup you want to change • Tune down or up the radio frequency in AM/FM mode 12. Mute all sound 13. Select among subwoofer sound level (SOFT SUBWOOFER, BALANCE SUBWOOFER, STRONG SUBWOOFER and POWERFUL SUBWOOFER) 14. Adjust individual speaker volume. Refer to “Advanced Sound Control” for details 15. Adjust the volume 16. Select programmed stations in AM/FM mode or directly access the next or previous file in USB mode 17. Start, stop or pause playback (in USB mode only) • Start reverse or forward accelerated play(in USB mode only) • Access MP3/WMA ID3 information and current play time, current play folder and track number, play mode • Access the repeat function • Turn on/off random playback • Enter Intro mode 18. Enter sleep mode and selects sleep time 19.Select audio sources Press ON•OFF Press the Number buttons Press MEMORY Press MONO/ST Press TEST TONE Press NIGHT Press EQ Press / Press SURROUND Press SETUP Press DISTANCE Press / Press / Press TUNER - and TUNER + Press MUTE Press SUBWOOFER Press LEVEL Press VOL + / VOL - Press CH+ / CH- Press PLAY, STOP or PAUSE to access the relative functions. Press REV or FWD Press DISPLAY Press REPEAT Press RANDOM Press INTRO Press SLEEP Press SOURCE buttons RT2770 QSG EN 6/3/07 5:19 PM Page 2

1. Center: In surround mode, the center speaker carries most of the dialog as well as music and effects. It should be set between the left and right speakers. 2. Front Speakers: Front speakers carry primarily music and sound effects. 3. Rear Speakers: The rear speakers’ overall sound balance should be as close as possible to the front speakers. Proper placement is vital to establish an evenly distributed sound field. 4. Subwoofer: A subwoofer is designed to reproduce powerful low bass effects (explosions, the rumble of spaceships, etc.) which dramatically heighten the action on the screen. 3. Front Surround sound Effect(FSsE) Setting (Optional) Front Surround sound Effect(FSsE) Setting If placing the rear speakers (surround speakers) at the back is not a good choice for you, you can use the Front Surround sound Effect(FSsE). Follow the following instruction for setting the speakers. Mounting the Speakers 1. Match the front left and rear left speakers together and match the front right and rear right speakers together. Place the front speaker upside down. 2. Slide in the hinge to the bottom of the front speaker until the ‘click’ sound is heard. 3. Slide in the rear speaker to the hinge until the ‘click’ sound is heard. 4. Attach the four rubber feet provided to the top of the front speaker. Adjusting the Angle of the Speakers To achieve the best Front Surround sound Effect (FSsE), adjust the mounted front left and the rear left speakers to the left for an angle of 25o - 45o from the center. Adjust the mounted front right and rear right speakers to the right in the same way. Place the rear speakers and subwoofer a foot or more away from TV. After adjusting the angle, the speaker should look like this illustration. 4. Connecting to Audio Components • The jacks on the back of the unit are used to connect to other components. One optical and one coaxial digital input jacks are provided for connection. • To connect a SAT receiver or a DVD player with a digital output, use an optical digital cable (not included) or a coaxial digital cable (included) to carry the audio signal and enjoy Dolby Digital sound quality. General controls Front panel controls 1. ON/STANDBY Turns on/off the unit. When the unit is turned on, the unit will go to the mode it was in before powered off. 2. Starts and pauses playback in USB mode. 3. Stops playback in USB mode. 4. / (PRESET buttons) Selects preset stations in AM/FM mode. Directly accesses the previous or next track in USB mode. 5. USB jack Connects USB devices. 6. LINE IN Connects components for audio input. 7. / (SURROUND buttons) Selects digital sound processor. (STEREO, HALL, CHURCH, CLUB, STADIUM, STUDIO, 3 STEREO, DOLBY PL EMULATION, DOLBY PL II MUSIC, DOLBY PL II MOVIE) 8. DVD/DVR, TV, SAT.CAB, AM/FM, VCR, USB and LINE-IN (SOURCE buttons) Selects sound source. 9. Headphones jack 10.MASTER VOLUME Adjusts the volume. 11.SUBWOOFER Selects among subwoofer output levels. (SOFT SUBWOOFER, BALANCE SUBWOOFER, STRONG SUBWOOFER, POWERFUL SUBWOOFER) 3 3 1 1 2 4 Courtesy Dolby Laboratories Left Rear Speaker (Surround) Left Front Speaker Center Right Front Speaker Right Rear Speaker (Surround) Subwoofer DVD/SAT/CAB COAXIAL OPTICAL 1 2 3 4 5 6 7 8 9 10 11 Digital Input Connect components capable of outputting Dolby digital (e.g. DVD or SAT) or standard PCM (CD) format digital signals. Read section on "Input Signal Setting" under "Advanced Sound Control" carefully to adjust the matching input settings. 1 2 Hinge Bottom Top Front Speaker Rear Speaker Rear Speaker Center Front Speaker Front Speaker 25o - 45o 25o - 45o 3 4 Front Speaker Rear Speaker Rubber Feet RT2770 QSG EN 6/3/07 5:19 PM Page 4