Sharp DV-SR45U Operation Manual

your DVD recorder. 1 The region number for this DVD recorder is 1. INSTRUCCIONES EN ESPAÑOL INCLUIDAS. DV-SR45U • Remote control (9HSNB006UD) with two “AA” size batteries • Round Coaxial cable (9HSWPZ0901TM003) • Audio/Video cables (9HSWX1E56B5-001) • Operation Manual (9HS1VMN20185) • Quick Use Guide (9HS1VMN20228) Operation Manual Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Supplied Accessory

2 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITAR LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND. CAUTION: THIS UNIT IS A CLASS 1 LASER PRODUCT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI- FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. AS THE LASER BEAM USED IN THIS UNIT IS HARMFUL TO THE EYES, DO NOT ATTEMPT TO DISASSEMBLE THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. This symbol warns the user of uninsulated voltage within the unit that can cause dan- gerous electric shocks. This symbol alerts the user that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SER- VICEABLE PARTS INSIDE. REFER SERVICING TO QUAL- IFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For future reference, record the serial number (located on the rear of the Unit) in the space provided. Model No.: DV-SR45U Serial No.: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. “WARNING—FCC Regulations state that any unauthorized changes or modi- fications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.” This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Este aparato digital de la Clase B cumple con la norma ICES-003 de Canadá.

Connections Getting started Changing the SETUP menu Others Español 3 Before you start Precautions (cont’d) 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions- The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol clean- ers. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the pos- sibility of the loss of an authorization code for a CATV con- verter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description oth- erwise required in item 5. 6.Attachments - Do not use attachments not recommended by the video product manufacturer as they may cause hazards. 7. Water and Moisture- Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8.Accessories - Do not place this video product on an unsta- ble cart, stand, tripod, bracket, or table.The video product may fall, causing serious injury to a child or adult, and seri- ous damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product.Any mount- ing of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. 9. Transportation - A product and cart combination should be moved with care. Quick stops, excessive force, and uneven sur- faces may cause the appliance and cart combination to overturn. 10.Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these open- ings must not be blocked or covered.The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface.This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufac- turer's instructions have been adhered to. 11. Power Sources - This video product should be operated only from the type of power source indicated on the mark- ing label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization - This video product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other).This plug will fit into the power outlet only one way.This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your elec- trician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying par- ticular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 14. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the video product,be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with regard to proper grounding of the mast and supporting structure,grounding of the lead-in wire to an anten- na discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig.A) 15. Lightning - For added protection for this video product dur- ing a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall out- let and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges. 16. Power Lines - An outside antenna system should not be locat- ed in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry - Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product. 19. Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service - Unplug this video product from the wall outlet and refer servicing to qualified service per- sonnel under the following conditions: a.When the power-supply cord or plug is damaged. b. If liquid has been spilled,or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by follow- ing the operating instructions. Adjust only those controls that are covered by the operating instructions as an improp- er adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. e. If the video product has been dropped or damaged in any way. f.When the video product exhibits a distinct change in per- formance this indicates a need for service. 21. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteris- tics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 22. Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. 23. Heat - This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMP GROUND CLAMP ELECTRIC SERVICE EQUIPMENT POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC – NATIONAL ELECTRICAL CODE S2898A Important Safeguards

4 Copy Protection Warning of Dew Formation This Unit supports Macrovision copy protection. On DVD discs that include a copy protection code, if the contents of the DVD disc are copied using the DVD recorder, the copy protection code prevents the DVD copy from playing normally. Moisture may form inside the DVD recorder under the following conditions: • Immediately after a heater is turned on. • In a steamy or humid room. • When the DVD recorder is suddenly moved from a cold to warm environment. If moisture forms inside this DVD recorder, it may not operate properly. In such case, turn on the power and wait for more than two hours for the moisture to evaporate. Notice for progressive scan outputs Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding our TV set compatibility with this model 525p DVD player, please contact our customer service center. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093 licensed for limited viewing uses only. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protec- tion technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. No Fingers or Other Objects Inside Do not put your fingers or objects on the disc tray. Location and Handling Location and Handling • Do not cover or place the DVD recorder in enclosed spaces to prevent excessive temperature build up. • Do not place the DVD recorder in direct sunlight, or near heat sources. • Depending on the use environment, the temperature of the DVD recorder may increase slightly.This is not a malfunction. • Keep the DVD recorder away from strong magnetic objects. • Do not stand the unit vertically. Install the unit in a horizontal and stable position. • Do not place any object containing water or other liquids on the DVD recorder. In the event that liquid should enter the cabinet, unplug the DVD recorder immediately and contact the retailer or service centre approved by SHARP immediately. • Do not remove the DVD recorder cabinet.Touching parts inside the cabinet could result in electric shock and/ or damage to the DVD recorder. For service and adjustment inside the cabinet, call a qualified dealer or service centre approved by SHARP. Nonuse Periods Location and Handling • When the DVD recorder is not being used, switch the DVD recorder to the Standby mode. • When left unused for a long period of time, the DVD recorder should be unplugged from the household AC outlet. • Do not place the DVD recorder in direct sunlight, or near heat sources. Manufactured under license from Dolby Laboratories.“Dolby” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 5 SERVICING 1. Please refer to relevant topics in the Troubleshooting on pages 92-95 before returning the product. 2. Do not attempt to service this Unit yourself. Instead, unplug it and contact a Sharp Authorized Service Center for inspection. (See Service Information on page 97.) 3. Be sure the service technician uses authorized replacement parts or their equivalents. Unauthorized parts may cause fire, elec- trical shock, or other hazards. 4. Following any service or repair, be sure the service technician performs safety checks to certify that this Unit is in safe operat- ing order. CLEANING THE CABINET ¡Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive. CLEANING DISCS ¡When a disc becomes dirty, clean it with a cleaning cloth.Wipe the disc from the center out. Do not wipe in a circular motion. ¡Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records. RECOMMENDED MEASURES FOR OPTIMUM PICTURE EXCELLENCE This Unit is a precision device constructed using extremely accurate technology. ¡The disc cannot be played if the disc drive component is worn out or if the internal pick up lens is dirty. ¡If this unit still does not perform properly although you refer to the relevant sections and to Troubleshooting on pages 92-95, the laser optical pickup unit may be dirty. Consult a Sharp Authorized Service Center for inspection and cleaning of the laser optical pickup unit. DISC HANDLING ¡Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs. ¡Always store the disc in its protective case when it is not used. Maintenance A NOTE ABOUT RECYCLING This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes. Make your contribution to the environment!!! • Used up batteries do not belong in the dust bin. • You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details. Others It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary. “Licensed under one or more of U.S. Pat. 4,972,484, 5,214,678, 5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985, 5,740,317, 5,777,992, 5,878,080, or 5,960,037.”

Before you start 6 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Step by step playback . . . . . . . . . . . . . . . . . . . . . . . .48 Slow forward / Slow reverse play . . . . . . . . . . . . . . .48 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Title/Chapter search . . . . . . . . . . . . . . . . . . . . . . . .50 Track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Repeat/Random/Program playback . . . . . . . . . .52 Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Random playback . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Program play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Selecting the format of audio and video . . . . . .54 Switching audio soundtrack . . . . . . . . . . . . . . . . . . .54 Switching subtitles . . . . . . . . . . . . . . . . . . . . . . . . . .55 Switching camera angles . . . . . . . . . . . . . . . . . . . . . .56 Reducing block noise . . . . . . . . . . . . . . . . . . . . . . . .56 Editing . . . . . . . . . . . . . . . . . . . . . . . . .57 Information on disc editing . . . . . . . . . . . . . . . . .57 Guide to a title list . . . . . . . . . . . . . . . . . . . . . . . . . .57 Editing discs with Video mode . . . . . . . . . . . . . . . . .57 Editing discs with VR mode . . . . . . . . . . . . . . . . . . .58 Editing DVD-RW discs in Video mode . . . . . . . .59 Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Putting names on titles . . . . . . . . . . . . . . . . . . . . . .60 Setting or clearing chapter markers . . . . . . . . . . . . .62 Editing DVD-RW discs in VR mode (Original) . .63 Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .64 Putting names on titles . . . . . . . . . . . . . . . . . . . . . .65 Setting or clearing chapter markers . . . . . . . . . . . . .67 Setting pictures for thumbnails . . . . . . . . . . . . . . . . .68 Setting titles to protect . . . . . . . . . . . . . . . . . . . . . .70 Releasing titles from protecting . . . . . . . . . . . . . . . .71 Editing DVD-RW discs in VR mode (Playlist) . . .72 Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .73 Putting names on titles . . . . . . . . . . . . . . . . . . . . . .74 Setting or clearing chapter markers . . . . . . . . . . . . .76 Setting pictures for thumbnails . . . . . . . . . . . . . . . . .77 Adding titles to a Playlist . . . . . . . . . . . . . . . . . . . . .79 Deleting a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . .80 Editing DVD-R discs . . . . . . . . . . . . . . . . . . . . . .81 Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 Putting names on titles . . . . . . . . . . . . . . . . . . . . . .82 Changing the SETUP menu . . . . . . . . .83 Tour of the SETUP menu . . . . . . . . . . . . . . . . . .83 Language setting . . . . . . . . . . . . . . . . . . . . . . . . .84 Display setting . . . . . . . . . . . . . . . . . . . . . . . . . . .86 Audio setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 Settings for Parental lock level . . . . . . . . . . . . . .90 Others . . . . . . . . . . . . . . . . . . . . . . . . .92 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .92 Language code . . . . . . . . . . . . . . . . . . . . . . . . . .95 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Service Information (For the U.S.) . . . . . . . . . . .97 Español . . . . . . . . . . . . . . . . . . . . . . . . .98 Before you start . . . . . . . . . . . . . . . . . . .2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . .6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Functional overview . . . . . . . . . . . . . . . . . . . . . . .8 Installing batteries in the remote control . . . . . . . . .10 Using a remote control . . . . . . . . . . . . . . . . . . . . . .10 DISPLAY menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 SETUP/DISC/CD menu . . . . . . . . . . . . . . . . . . . . . .11 Connections . . . . . . . . . . . . . . . . . . . . .13 Connection to a TV . . . . . . . . . . . . . . . . . . . . . . .13 Connection to a cable box or satellite box . . . .14 When connecting to a cable box or satellite box with only a few scrambled channels . . . . . . . . . . . . . . . . .14 When connecting to a cable box or satellite box with many scrambled channels . . . . . . . . . . . . . . . . . . . . .14 Connection to an Audio System . . . . . . . . . . . . .15 Getting started . . . . . . . . . . . . . . . . . . .16 Easy DVD recording . . . . . . . . . . . . . . . . . . . . . .16 Channel setting . . . . . . . . . . . . . . . . . . . . . . . . . .18 Getting channels automatically . . . . . . . . . . . . . . . . .18 Adding/deleting channels . . . . . . . . . . . . . . . . . . . . .19 Selecting the TV stereo or SAP . . . . . . . . . . . . .20 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . .21 Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . .21 Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . . .22 Setting the daylight saving time . . . . . . . . . . . . . . . .24 Selecting the TV aspect ratio . . . . . . . . . . . . . . .25 Recording . . . . . . . . . . . . . . . . . . . . . . .26 Information on DVD recording . . . . . . . . . . . . . .26 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Recording speed . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Restrictions on recording . . . . . . . . . . . . . . . . . . . .26 Information on copy control . . . . . . . . . . . . . . . . . .27 Making discs playable in other DVD player (Finalize) 27 Formatting a disc . . . . . . . . . . . . . . . . . . . . . . . .28 Choosing the recording format of a blank disc . . . . .28 Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . . .30 Basic recording . . . . . . . . . . . . . . . . . . . . . . . . . .31 Checking the recording picture quality . . . . . . . . . .32 One-touch timer recording . . . . . . . . . . . . . . . .33 Timer recording . . . . . . . . . . . . . . . . . . . . . . . . .34 Hints for timer recording . . . . . . . . . . . . . . . . . . . . .36 Settings for an external source . . . . . . . . . . . . . .37 Connection to an external source . . . . . . . . . . . . . .37 Recording from an external source . . . . . . . . . . . . .38 Finalizing the discs . . . . . . . . . . . . . . . . . . . . . . .39 Setting a disc to protect . . . . . . . . . . . . . . . . . . .40 Playing discs . . . . . . . . . . . . . . . . . . . . .41 Information on DVD play . . . . . . . . . . . . . . . . . .41 Guide to displays . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Playing discs using the disc menu . . . . . . . . . . . . . . .44 Playing discs using the title menu . . . . . . . . . . . . . . .45 Special playback . . . . . . . . . . . . . . . . . . . . . . . . .46 Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Fast forward / Fast reverse . . . . . . . . . . . . . . . . . . .46 Skipping TV commercials during play . . . . . . . . . . . .47

Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 7 Recording This DVD recorder is compatible with both DVD-RW, which is rewritable repeatedly, and DVD-R, which is avail- able for recording once.You can choose either one for your convenience. Up to 8 program recording: You can program the DVD recorder to record up to 8 programs, up to a year in advance. Daily or weekly pro- gram recordings are also available. One-touch timer recording: You can easily set a recording time as you prefer. Every time the REC button pressed during recording, the recording time will be increased by 30 minutes up to 4 hours.The recording automatically stops when the record- ing time you set is reached. REC MONITOR: You can confirm the picture quality for recording in the current recording speed which you set. If you want to change the recording speed, press REC MODE button to set the desired recording mode. Automatic Chapter marker setting: Chapter markers will be put on recordings as you set in SETUP menu before attempting to record. Automatic Title menu making: The DVD recorder makes title menus automatically when finalizing the disc which are recorded in Video mode. Automatic PLAYLIST making (VR mode): A Playlist will be prepared from an Original list, so that you can edit titles in a Playlist as you prefer. An Original list is kept as it is. Play Theater surround sound in your home: When connecting the DVD recorder to an amplifier or a decoder which is compatible with Dolby Digital or DTS, you are allowed to experience the theater surround sound from discs with surround sound system. Quick search for what you want to watch: You can easily find the part you want to watch using the search function. Search for a desired point on a disc by title, chapter, or time. Start to play from Original and Playlist: Title playing is available from either an Original list or Playlist. Editing Setting/Clearing chapter markers: You can easily add chapter markers anywhere in your recordings for easy editing. (VR mode) Making your own Playlist: With the original remains as it is, you can edit titles on various Playlist as you prefer. Putting names on titles Setting pictures for thumbnails Setting/clearing chapter markers Deleting parts of titles etc Protecting titles: To avoid editing or erasing titles, the protect function is useful when it is ON in the original list. Compatibility Available for playing discs recorded in Video mode on a regular DVD player (Video mode): Discs recorded in Video mode can be played on regular DVD players, including computer DVD drives compatible with DVD-Video playback*.You will need to finalize the discs recorded in Video mode to play in other DVD play- ers. * DVD-Video Format (Video mode) is a new format for record- ing on DVD-RW/R discs that was approved by the DVD Forum in 2000.Adoption of this format is optional for manufactures of DVD playback devices, and there are DVD-Video players, DVD- ROM drives or other DVD playback devices that do not play DVD-RW/R discs recorded in the DVD-Video Format. Others Progressive Scan system Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolu- tion than that of traditional television signals. This DVD unit not only plays DVDs and CDs but also offers features for you to record to DVD discs and edit them after that. The following features are offered with this DVD recorder. Symbol in this operation manual Many functions of this DVD recorder are depending on the disc type or the recording mode. To specify for what disc type or recording mode each function is, we put the following symbols at the beginning of each item to operate. Symbol Description Available to DVD Video discs Avaialble to DVD-RW in Video mode Avaialble to DVD-RW in VR mode Available to DVD-R discs Available to DVD+RW in Video mode Available to DVD+R discs Available to Audio CDs Available to CD-RW/R discs with MP3 files DVD-RW DVD-RW VR DVD-R DVD-R DVD-RW DVD-RW Video DVD-V DVD-V CD CD MP3 MP3 DVD+R DVD+R DVD+RW DVD+RW Video Features

8 Front Panel 1. POWER button Press to turn the DVD recorder on and off. If timer programmings have been set, press to set the unit in timer-standby mode. 2. CH L / K button Press to change the channel up and down. 3. E (REV) button During playback, press to skip to the previous chapter or track. During playback,press and hold for 1.5 seconds to fast reverse. When playback is paused, press repeatedly to slow reverse. 4. D (FWD) button During playback, press to skip to the next chapter or track. During playback, press and hold for 1.5 seconds to fast forward. When playback is paused, press repeatedly to slow forward. 5. C (STOP) button* Press to stop play or recording. 6. B (PLAY) button* Press to start or resume play. 7. OPEN/CLOSE A button* Press to open or close the disc tray. 8. Disc tray Place a disc when open. 9. Display Refer to “Front Panel Display Guide” on page 12. 10. Remote control sensor Receive signals from your remote control so that you can control the DVD recorder from a distance. 11. REC/OTR button Press once to start a recording. Press repeatedly to start a one-touch timer recording. 12. REC MODE button Press to switch the recording speed. 13. AUDIO INPUT jacks (LINE2) Use to connect external equipment with standard audio cables. 14. VIDEO INPUT jack (LINE2) Use to connect external equipment with a standard video cable. 15. S-VIDEO INPUT jack (LINE2) Use to connect the S-Video output of external equip- ment with an S-Video cable. Rear Panel DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO INPUT COMPONENT VIDEO OUTPUT TV ANTENNA OUTPUT R R L L AUDIO VIDEO 1 2 (L1) VIDEO S-VIDEO S-VIDEO PR/CR PB/CB Y 1 3 6 2 11 10 9 7 4 8 5 1. AC Power Cord Connect to a standard AC outlet to supply power to this unit. 2. AUDIO OUTPUT jacks 1, 2 Use to connect a TV monitor,AV receiver or other equipment with standard audio cables. 3. VIDEO OUTPUT jack Use to connect a TV monitor,AV receiver or other equipment with a standard video cable. 4. S-VIDEO OUTPUT jack Use to connect the S-Video input of a TV monitor,AV receiver or other equipment with an S-Video cable. 5. COMPONENT VIDEO OUTPUT jacks Use to connect a TV monitor with component video inputs with component video cables. 6. TV ANTENNA IN jack Use to connect an antenna. 7. TV ANTENNA OUT jack Use to connect an antenna cable to pass the signal from the TV ANTENNA IN to your TV monitor. 8. S-VIDEO INPUT jack(LINE1) Use to connect the S-Video output of external equip- ment with an S-Video cable. 9. VIDEO INPUT jack(LINE1) Use to connect external equipment with a standard video cable. 10. AUDIO INPUT jacks(LINE1) Use to connect external equipment with standard audio cables. 11. COAXIAL DIGITAL AUDIO OUTPUT jack Use to connect an AV receiver, Dolby Digital decoder or other equipment with a coaxial digital input jack with a digital coaxial cable. Note • Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the DVD recorder. • This unit does not have an RF modulator. REC/OTR OPEN/CLOSE 1 2 3 4 5* 6* 7* 8 9 12 11 10 15 13 14 (*) The unit can also be turned on by pressing these buttons.

Before you start Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 9 7. REC button Press once to start a record- ing. Press repeatedly to start a One-Touch timer Recording. 8. PAUSE F button Press to pause play or recording. 9. PLAY B button* Press to start or resume play. 10. REV E button During playback, press to fast reverse. Or when playback is paused, press to play slow reverse. 11. STOP C button* Press to stop play or record- ing. 12. SETUP button Press to display the setup menu. During DVD playback, press and hold for more than 3 sec- onds to switch to the pro- gressive scanning mode or the interlace mode. 13. TOP MENU button Press to display the top menu. 1. POWER button Press to turn the DVD recorder on and off. If timer programmings have been set, press to set the unit in timer-standby mode. 2. DISPLAY button Press to display or change the on-screen display. 3. CH K / L buttons Press to change the channel up and down. 4. REC MONITOR button Press to check the video sig- nal to be recorded before attempting. 5. REC MODE button Press to switch the recording speed. 6. CLEAR button Press to clear the password once entered or to cancel the programming for CD or to clear the selecting marker num- ber in the marker setup mode or to clear the program once entered in the timer recording setting mode,etc. 14. REPEAT button Press to display the repeat setting menu. 15. ZOOM button During playback, press to enlarge the picture on the screen. 16. OPEN/CLOSE A button* Press to open or close the disc tray. 17. TIMER PROG. button Press to display the timer program setting menu. 18. Number buttons Press to select channel numbers. Press to select a title/chap- ter/track on display or a TV channel. Or press to enter values for the settings in the SETUP menu. 19. CM SKIP button During playback, press to skip 30 seconds. 20. SKIP H button During playback, press to skip to the previous chapter or track. Or when playback is paused, press to play reverse step by step. SKIP G button During playback, press to skip to the next chapter or track. Or when playback is paused, press to play forward step by step. 21. FWD D button During playback, press to play fast forward. Or when playback is paused, press to play slow forward. 22. MENU/LIST button Press to display the Disc menu. To change ORIGINAL and PLAYLIST on the TV screen. (VR mode only) 23. ENTER button Press to confirm or select menu items. 24. K / L / { / B buttons Press to select items or set- tings. 25. RETURN button Press to return to the previ- ously displayed menu screen. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 12 1 16* 18 19 20 21 22 24 25 23 17 3 4 5 7 9* 11* 15 14 2 6 8 10 13 (*) The unit can also be turned on by pressing these buttons. Remote Control

Before you start 10 DISPLAY menu Press DISPLAY button to call up the display menu.This menu will give you the information on the playing disc. Some operations are available while disc is playing. Details are on page 41. 1. Indicates a disc type and a format mode. NOTE: In some descriptions on this manual, only one disc type is indicated as an exam- ple. 2. Indicates a recording mode and possible recording time. 3. Indicates a title number, chap- ter number, and the time lapse of disc play. 4. Each icon means: : Search : Audio : Subtitle : Angle (except VR mode) : Repeat : Marker : Noise Reduction : Zoom DVD-RW SP 1:25 Rem. Video mode 1 1 00:00:00 1 3 2 4 Using a remote control Keep in mind the following when using the remote control: • Make sure that there is no obstacle between the remote control and the remote sensor on the DVD recorder. • Use within the operating range and angle as shown. • Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the remote sensor of the DVD recorder. • Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the DVD recorder. • Replace the batteries when you notice a fall off in the operating range of the remote control. Installing batteries in the remote control Install two “AA” size batteries (supplied) matching the polarity indicated inside battery compartment of the remote control. Note: Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following: • Do not mix new and old batteries together. • Do not use different kinds of batteries together, although they may look similar, different batteries may have different voltages. • Make sure that the plus and minus ends of each battery match the indications in the battery com- partment. • Remove batteries from equipment that is not going to be used for a month or more. • When disposing of used batteries, please comply with governmental regulations or environmental public instruction's rules that apply in your country or area. • Do not recharge, short-circuit, heat, burn or disas- semble batteries. POWER DISPLAY REC SPEED CLEAR CM SKIP SKIP REC PAUSE P ENTER REC MONITOR OPEN/CLOSE TIMER PROG. MENU PLAY LIST TOP MENU/ ORIGINAL SPACE 1 2 3 4 5 6 7 8 9 0 FWD STOP PLAY REV CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ Remote control 60˚ Within about 23feet (7m) 2 1 3 Guide to Displays on screen menu This unit uses the following on screen menu for most operations: SETUP/DISC/CD menu,Title list, and DIS- PLAY menu.They allow you to change the playing status of disc during play. The DISPLAY menu also gives you information on the status of the disc.

Before you start Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 11 1. Playback: To set up the DVD recorder to play discs as you prefer. 2. Recording: To set up the DVD recorder to record to discs as you prefer. 3. Display: To set up the OSD screen and the front display of the DVD recorder as you prefer. 4. Select Video: To choose a line input to record to DVD discs from other video equipment. 5. Clock: To set up the clock of the DVD recorder as you need. 6. Channel: To adjust the channel setting of the DVD recorder as you prefer. 1. Edit: Turns on a title list, (When a disc with VR mode is inserted, 'Original' or 'PlayList' is available.), which shows the recorded titles on the disc. 2. Format (DVD-RW only): Allows you to erase all of the recorded content on the disc. The disc will be completely blank. • Erased content cannot be called back. Please make sure before you format a disc. • A DVD-RW disc formatted with this unit cannot be used in other DVD recorders without any recording using this unit. • If you want to use a disc only for- matted with this unit on another DVD recorder, you have to re-for- mat the disc on that recorder. 3. Finalize: Allows you to finalize a disc containing recorded titles. 4. Disc Protect (VR mode only) : Allows you to protect a disc from accidental editing or recording. 1. Random Play: To activate the random playback feature. 2. Program Play: To activate the programmed play- back feature. CD Playback Mode CD Playback Mode Random Play Program Play 1 2 Disc Setting Disc Edit Format Finalize Disc Protect OFF ON 1 2 3 4 Setup Menu Setup Playback Setting 1 2 3 4 5 6 “SETUP” is available only in the Stop mode. “DISC” is available only when a DVD-RW/R disc is insert- ed into the unit. When a DVD-Video disc (commercially available), new DVD-R disc, or the finalized DVD-R disc is inserted into the unit, you cannot select “DISC”. “CD” is available only when an Audio CD disc or a CD-RW/R disc with MP3 files is inserted into the DVD recorder. SETUP/DISC/CD menu Press SETUP button to display the setup main menu, then choose either of SETUP/DISC/CD by { / B button. Then, press ENTER button to display each menu. These menus provide entries to all main functions of the DVD recorder.

Before you start 12 Front Panel Display Guide 1. Current status of the DVD recorder : Appears when disc play- back is paused. : Appears when playing a disc. : Appears when the timer programming has been set and is proceeding. : Appears during recording process. : Appears during repeat play. 2. Disc type : Appears when an audio CD or a disc with MP3 files is inserted in the disc tray. : Appears when a DVD disc is inserted in the disc tray. : Appears when a DVD-R disc is inserted in the disc tray. : Appears when a DVD- RW disc is inserted in the disc tray. 3. Recording speed Indicates the recording speed of the disc. Display message 4. Title/Track and Chapter mark : Appears when indicating a title/track number. : Appears when indicating a chapter number. 5. Displays the following • Playing time / remaining time • Current title / chapter / track number • Recording time • Clock • Channel number • OTR (one-touch timer recording) remaining time 6. : Appears in the after- noon with the clock displaying. 7. : Appears when the pro- gressive scan system is activated. Appears when data is being recorded on a disc. 1 6 3 7 5 2 4 Appears when the disc tray is opening. Appears when the DVD recorder is turned on. Appears when the DVD recorder is turned off. Appears when the disc tray is closing. Appears when a disc is loaded on the disc tray.

Connections Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Make one of the following connections, depending on the capabilities of your existing equipment. DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO INPUT COMPONENT VIDEO OUTPUT TV ANTENNA OUTPUT R R L L AUDIO VIDEO 1 2 (L1) VIDEO S-VIDEO S-VIDEO PR/CR PB/CB Y R L OUTPUT R L AUDIO 1 OUTPUT R L AUDIO 2 or S-VIDEO IN OUTPUT S-VIDEO PB/CB Y PR/CR COMPONENT VIDEO IN COMPONENT VIDEO OUTPUT PR/CR PB/CB Y AUDIO OUT TV Basic Audio Method 1 Method 2 Better picture Best picture S-VIDEO OUT COMPONENT VIDEO OUT Audio cable (supplied) S-Video cable (commercially available) Component Video cables (commercially available) DVD Recorder DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO INPUT COMPONENT VIDEO OUTPUT TV ANTENNA OUTPUT R R L L AUDIO VIDEO 1 2 (L1) VIDEO S-VIDEO S-VIDEO PR/CR PB/CB Y AUDIO IN VIDEO Round Coaxial Cable (supplied) Video Cable (supplied) Audio Cable (supplied) (Back of TV) Plug in the AC power cord of the DVD recorder. or Cable Signal or Cable Signal Connect Connect Connect Connect Disconnect Antenna Antenna (Back of DVD recorder) (Back of TV) 3 2 1 6 4 5 Note • Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system. • When Progressive Scan mode is selected, no video signal will be output from the VIDEO OUT or S-VIDEO OUT jack. If your TV is compatible with Progressive Scan (480p) and you want to enjoy that high quality picture; You must select the connection Method 2 above and Progressive Scan mode.To set the mode, press and hold the SETUP button on the remote control for more than 3 seconds during DVD playback, so that “P.SCAN” will appear on the display of this unit. If your TV is not compatible with Progressive Scan; Use this unit in Interlace mode. Make sure that no “P.SCAN” is on the display of this unit. If not, press and hold the SETUP button on the remote control for more than 3 seconds during DVD playback, so that “P.SCAN” on the display of this unit will disappear. SETUP REPEAT ZOOM ENTER RETURN MENU/LIST TOP MENU { B FWD g STOP C PLAY B REV h K more than 3 seconds during DVD playback [Interlace mode] [Progressive Scan mode] 13

Connections 14 Note to the Cable TV System Installer : This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible. When connecting to a cable box or satellite box with only a few scrambled channels If you are using a cable box or satellite box with only a few scrambled channels, follow the setup on this page. If many or all the channels are scrambled, use the connection on this page. With this setup: • You can record any unscrambled channel by selecting the channel on the DVD recorder. • You cannot record scrambled channels that require a cable box or satellite box. When connecting to a cable box or satellite box with many scrambled channels If many or all the channels you receive by cable or satellite are scrambled, we recommend using this setup. With this setup: • You can record any unscrambled channel by selecting the channel on the cable box or satellite box. Be sure that the cable box or satellite box is turned on. • You cannot record one channel while watching another channel. DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO INPUT COMPONENT VIDEO OUTPUT TV ANTENNA OUTPUT R R L L AUDIO VIDEO 1 2 (L1) VIDEO S-VIDEO S-VIDEO PR/CR PB/CB Y AUDIO IN VIDEO Round Coaxial cable (supplied) Video cable (supplied) Audio cable (supplied) (Back of TV) Cable Signal Connect Connect Connect Connect (Back of DVD recorder) 2 1 3 4 IN OUT (Cable box or Satellite box) Round Coaxial cable DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO INPUT COMPONENT VIDEO OUTPUT TV ANTENNA OUTPUT R R L L AUDIO VIDEO 1 2 (L1) VIDEO S-VIDEO S-VIDEO PR/CR PB/CB Y AUDIO IN VIDEO Video cable (supplied) Audio cable (supplied) (Back of TV) Cable Signal Connect Connect (Back of DVD recorder) Round Coaxial cable Connect 1 Connect 2 Round Coaxial cable (supplied) 4 5 Round Coaxial cable IN OUT (Cable box or Satellite box) Connect 3 A B B

Connections Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 15 • When you change the connections, all devices should be turned off. • Refer to the operation manual accompanying external devices for more information. or OUTPUT R L AUDIO 1 OUTPUT R L AUDIO 2 Stereo system COAXIAL DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO Method 1 Analog audio input jacks Digital audio input jack AUDIO OUT DIGITAL AUDIO OUT Method 2 Audio cable (supplied) Audio Coaxial Digital cable (commercially available) Note • If output is Dolby Digital encoded audio, connect to a Dolby Digital decoder and set “Dolby Digital” to “Stream” for the “Digital Out” setting in the SETUP menu. (Refer to pages 88-89.) • If output is DTS encoded audio, connect to a DTS decoder and set “DTS” to “ON” for the “Digital Out” setting in the SETUP menu. (Refer to pages 88-89.) • The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or DAT deck. • Unless connected to a Dolby Digital decoder or a DTS decoder, set “Dolby Digital” to “PCM” and “DTS” to “OFF” for the “Digital Out” setting in the SETUP menu. Playing a DVD using incorrect settings may generate noise distor- tion and may also damage the speakers. (Refer to pages 88-89.) • Set “Dolby Digital” to “PCM” for the “Digital Out” set- ting in the SETUP menu for connecting to an MD deck or DAT deck. (Refer to pages 88-89.) • By hooking this unit up to a Multi-channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital 5.1 channel surround sound as heard in the movie theaters. • By hooking this unit up to the DTS decoder, you can enjoy 5.1channel surround system which reproduces the original sound as truthfully as possible. 5.1channel sur- round system is developed by the Digital Theater System, Inc. Dolby Digital decoder, DTS decoder or MD deck or DAT deck DVD Recorder

Getting started 16 The following will help you to understand easily how to record to DVD discs. Note: Make sure batteries are in the remote control and you have connected this unit and the TV correctly. Step 1: Choose a disc type There are several types of recordable DVD discs to choose from. Choose a recordable DVD disc type based on your playing/recording/editing reguire- ments. See “DVD disc types” at the bottom of this page for more information on the differences between the different kinds of compatible media. This DVD recorder can record on the following type of discs. * This unit cannot record on the following discs. • DVD-RW Ver 1.2 / 2-4x CPRM compatible • DVD-R General Ver 2.0 / 8x For example, when you want to record repeated- ly on the same disc, or when you want to edit the disc after recording, select the rewritable DVD- RW type disc. When you want to save recordings without any alteration, a non-rewritable DVD-R can be your choice. 4.7 Step 2: Insert a blank disc POWER DISPLAY OPEN/CLOSE TIMER PROG. 1 2 3 A CH .@/: ABC DEF GHI JKL MNO POWER DISPLAY OPEN/CLOSE TIMER PROG. 1 2 3 A CH .@/: ABC DEF GHI JKL MNO Remote Control To open To Close Format the disc Insert the disc in the recorder.Then, format the disc from SETUP menu.Video format (Video mode) or Video recording format (VR mode) will be available depending on the disc type inserted.This is necessary to prepare the disc for record- ing. Details are on pages 28- 30. * When you format, the entire contents on that disc will be erased. • The unit automatically starts formatting when an unused disc is inserted. DVD disc types . DVD-RW VR DVD-RW Video You want to Record TV programs Reuse by deleting unwanted contents Edit recorded contents Edit/Record from connected equipment Copy discs for distribution Play on other DVD equipment *1 *1 DVD-RW VR DVD-RW Video Features Recording Rewritable? Yes Yes Can create chapters at fixed intervals (auto.) Yes Yes Can create chapters wherever you like (manual) Yes No Can record 16:9 size pictures Yes Yes Can record Copy-Once programs Yes No Editing Can perform basic edit functions Yes Yes Can perform advanced edit functions (Playlist edit) Yes No No Yes No Yes No Yes No *1 DVD-RW (VR mode) can only be played on DVD equipment that is VR compatible. Note: For details of the above functions and implied restrictions, see the explanations inside the manual. DVD-R DVD-R : Most suitable. : Can be used. : Some functions are limited. : Cannot be used. 2 To turn on 1 3 Loading This operation may take a while to be recognized.

Getting started Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 17 Step 3: Select the recording speed POWER DISPLAY REC MODE CLEAR CM SKIP REC REC MONITOR OPEN/CLOSE TIMER PROG. SPACE 1 2 3 4 5 6 7 8 9 0 A CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ Step 5: Record to DVD discs POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE REC MONITOR OPEN/CLOSE TIMER PROG. SPACE 1 2 3 4 5 6 7 8 9 0 F A H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ Step 4: Select the desired channel POWER DISPLAY REC MODE CLEAR CM SKIP REC REC MONITOR OPEN/CLOSE TIMER PROG. SPACE 1 2 3 4 5 6 7 8 9 0 A CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ SP 2:01 Rem. Step 6: Stop the record REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP MENU/LIST TOP MENU SPACE 7 8 9 0 F FWD g STOP C PLAY B REV h H G K CH 1 I Writing to Disc 58% Hint 1: Play the recorded contents You can select the title you want to play from a displayed menu, and immediately start to play. Recorded contents are easily accessible, with simple procedure of choos- ing a title on a chapter in the menu screen. What is titles and chapters? The contents of DVD disc are generally divided into some titles.Titles may be further divided into chapters. Hint 2: Edit the recorded disc You will find editing discs is easy.This unit offers convenient edit functions which are possible only with DVD-R/RW discs. You can edit the following from a title list. • Putting names on titles • Setting pictures for thumbnails (VR mode) • Setting/clearing chapter markers • Deleting parts of titles or scenes (VR mode) Title Delete :This deletes an entire scene permanently from the disc. Scene Delete :This allows a user to edit within a specific scene (ex. commercials). Original and Playlist (VR mode) You can edit the recordings in Playlist without changing the original record- ings. Playlist does not take up much disc space. What “Original” or “Playlist” is for? Throughout this manual, you will find Original and Playlist to refer to the actu- al content and the edited version. • Original content refers to what’s actually recorded on the disc. • Playlist content refers to the edited version of the disc; how the Original content is to be played. Finalizing a Disc • This will allow a disc that is recorded on our unit to be played back on a differ- ent DVD player- without finalization it will not be playable on another player. • After finalizing a disc if the recording was in video mode, you can not edit any information that is on that disc. • If you have recorded in VR mode on DVD-RW disc then editing is still per- mitted after finalizing. Start Rec. Stop/Start Stop Rec. Title 1 Title 2 Chapter 1 Chapter 1 Chapter 2 Chapter 3 Chapter 2 This operation may take a while to be completed.

DVD recorder when purchased. We recommend that you get available channels in your area stored using “Auto Preset” in the Channel Preset of the SETUP menu. Getting channels auto- matically 1 Press POWER button to turn on the DVD recorder. 2 Turn the TV on and be sure to select the input to which the DVD recorder is connect- ed. 3 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: Setup Menu 4 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 5 Select “Channel” using K / L / { / B buttons, then press ENTER button. Channel Preset menu will appear. 6 Select “Auto Preset” using K / L buttons, then press ENTER button. The DVD recorder will start get- ting channels available in your area. 7 Press SETUP button to exit. •You can select only the channels memorized in this unit by using the CHANNEL buttons. Auto Presetting Now CH 18 Setup > Channel Preset Auto Preset Manual Preset TV Audio Select Stereo Setup Playback Setting Note • If the auto presetting is can- celled during presetting, some channels not yet preset may not be received. • The selection will depend on how you receive the TV chan- nels. To cancel the auto preset- ting during scanning: Press RETURN button or SETUP button to cancel. To select a channel You can select a channel by directly entering channel using the Number buttons on the remote control. Notes for using the Number buttons: • When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For exam- ple: 117, press 1,1,7) • You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). • You can select the line input mode (“L1” or “L2”). To select “L1” by pressing [0], [0], [1].To select “L2” by pressing [0], [0], [2]. Details are on page 38. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 3 4 5 6 1 7

Getting started Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 19 4 Select “Manual Preset” using K / L buttons, then press ENTER button. Manual Preset menu will appear. 5 Select the channel number to add or delete. Press { button to move to a lower channel number. Press B button to move to a higher channel number. 6 Select “Add” or “Delete” using K / L buttons, then press ENTER button. The channel number will be added or deleted from a channel memory.Then the next channel number will appear so that you can continue adding or deleting channels. 7 Press SETUP button to exit. Setup > Channel Preset > Manual Preset CH18 Add Delete CH2 Add Delete Setup > Channel Preset > Manual Preset Adding/deleting chan- nels The channels you no longer receive or seldom watch can be deleted from the memory.You also may add channels into memory. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Channel” using K / L / { / B buttons, then press ENTER button. Channel Preset menu will appear. Setup > Channel Preset Auto Preset Manual Preset TV Audio Select Stereo Setup Playback Setting Setup Menu POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 7 6

Getting started 20 You can select a sound channel to output from TV. “Stereo” has been selected as the default. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Channel” using K / L / { / B buttons, then press ENTER button. Channel Preset menu will appear. Setup > Channel Preset Auto Preset Manual Preset TV Audio Select Stereo Setup Playback Setting Setup Menu 4 Select “TV Audio Select” using K / L buttons, then press ENTER button. Option window will appear. 5 Select “Stereo” or “SAP” using K / L buttons, then press ENTER button. Stereo: Outputs main-audio. SAP: (Secondary Audio Program) Outputs Sub-audio. Refer to the item in “Glossary” on page 96 for more information. 6 Press SETUP button to exit. Setup > Channel Preset Auto Preset Manual Preset TV Audio Select Stereo Stereo SAP POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 6 Notes on TV channel audio • When you record a TV program available in second audio or stereo on a DVD-RW/R, you have to select either Stereo or SAP in the Channel Preset screen beforehand. Refer to the following table to check an appropriate setting. • As can be seen in the above table, when a TV program is available in second audion and you set Channel Preset to SAP, you can only play the recording in second audio. Selected Broadcast Disc Audio audio audio recording output Stereo STEREO+SAP STEREO STEREO STEREO STEREO STEREO MONO+SAP MONO MONO MONO MONO MONO SAP STEREO+SAP SAP SAP STEREO STEREO STEREO MONO+SAP SAP SAP MONO MONO MONO

Getting started Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 21 Set the clock before you try the timer recording. If a Public Broadcasting Station (PBS) is available in your area, follow Auto Clock Setting below. If not, follow Manual Clock Setting on pages 22-23. Auto Clock Setting Make sure • The antenna/Cable TV connec- tions are correct. • If this unit is connected to a Cable Box or Satellite Box, select the local PBS station on them to set the clock automatically. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B but- tons, then press ENTER button. SETUP menu will appear. 3 Select “Clock” using K / L / { / B buttons, then press ENTER button. Clock menu will appear. Setup > Clock Clock Setting Auto Clock Setting Daylight Saving Time Auto ON Setup Playback Setting Setup Menu 4 Select “Auto Clock Setting” using K / L buttons, then press ENTER button. Option window will appear. 5 • If you do not know your PBS channel number, select “Auto” using K / L buttons, then press ENTER button. • If you know your PBS chan- nel number, select “Manual” using K / L buttons, then press ENTER button. Enter your PBS channel number using Number or K / L buttons, then press ENTER button. 6 Press SETUP button to exit. 7 Press POWER button to turn off the DVD recorder. This unit will search for the time only when the power is off. Leave it off for several minutes to give this unit time to set the clock on the front display of the front panel. Setup > Clock Clock Setting Auto Clock Setting Auto Daylight Saving Time Off OFF Auto Manual Set Channel No. CH1 Setup > Clock Clock Setting Auto Clock Setting Auto Daylight Saving Time Off OFF Auto Manual Note • The clock may set itself auto- matically after you connect the antenna/cable signal to this unit and plug in the power cord. In this case, the current time will appear on the front panel display. • If the current time is not dis- played or the displayed clock is not correct, set the clock manually. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 6 7

Getting started 22 Manual Clock Setting 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Clock” using K / L / { / B buttons, then press ENTER button. Clock menu will appear. Setup > Clock Clock Setting Auto Clock Setting Daylight Saving Time Auto ON Setup Playback Setting Setup Menu 4 Select “Clock Setting” using K / L buttons, then press ENTER button. A clock setting window will appear. Press ENTER button again. Default date will appear. 5 Enter the date (month / day / year) using K / L buttons. Press { / B button to move the cursor. 6 Enter the time (hour / minute) using K / L buttons, then press { / B buttons. A cursor will move on AM or PM. Setup > Clock Clock Setting Auto Clock Setting Daylight Saving Time Auto JAN / 12 / 2004 (MON) 09 : 24 AM ON Setup > Clock Clock Setting Auto Clock Setting Auto Daylight Saving Time JAN / 12 / 2004 (MON) 12 : 00AM ON Setup > Clock Clock Setting Auto Clock Setting Daylight Saving Time Auto - - - / - - / - - - - ( - - - ) - - : - - ON Note • Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds when you set the clock manu- ally. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 6

Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Getting started 23 7 Press K / L buttons to select AM or PM, then press ENTER button. Clock menu will appear, then the settings will be activated. Setup > Clock Clock Setting Auto Clock Setting Daylight Saving Time Auto ON 8 Press SETUP button to exit. Although seconds are not displayed, they begin counting from zero. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 8 7 4 SETUP REPEAT ZOOM ENTER RETURN MENU/LIST TOP MENU { B FWD g STOP C PLAY B REV h K L 6 5 4 Select “Auto Clock Setting” using K / L buttons, then press ENTER button. Option window will appear. Setup > Clock Clock Setting Auto Clock Setting Auto Daylight Saving Time Off OFF Auto Manual Repeat steps (1) to (3) in “Manual Clock Setting”. When “Auto Clock Setting” is selected to “Auto” or “Manual”, change it to “OFF” as following steps. 5 Select “OFF” using K / L buttons, then press ENTER button. 6 Press SETUP button to exit.

Getting started 24 4 Select “Daylight Saving Time” using K / L buttons, then press ENTER button. Daylight Saving Time options will appear. 5 Select “ON” or “OFF” using K / L buttons, then press ENTER button. Choose “ON” when currently observing the daylight saving time. 6 Press SETUP button to exit. Setup > Clock Clock Setting Auto Clock Setting Daylight Saving Time ON OFF Auto Setting the daylight sav- ing time When Daylight Saving Time is ON, the DVD recorder clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Clock” using K / L / { / B buttons, then press ENTER button. Clock menu will appear. Setup > Clock Clock Setting Auto Clock Setting Daylight Saving Time Auto ON Setup Playback Setting Setup Menu POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 6

Getting started Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 25 You can select the TV aspect ratio to match the formats of what you are playing with the DVD recorder and your TV screen (4:3 standard or 16:9 widescreen TV). “4:3 Letter Box” has been select- ed as the default. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Playback” using K / L / { / B buttons, then press ENTER button. Playback menu will appear. Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup Playback Setting Setup Menu 4 Select “TV Aspect” using K / L buttons, then press ENTER button. Option window will appear. Refer to the Note on this page. 5 Select a desired option using K / L buttons, then press ENTER button. 6 Press SETUP button to exit. Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 16:9 Wide 8 English Original OFF ON OFF 4:3 Letter Box 4:3 Pan & Scan 16:9 Wide Note If you have a standard TV: Select “4:3 Letter Box”, so that black bars appear on the top and bottom of the screen. Select “4:3 Pan & Scan” for a full height picture with both sides trimmed. If you have a widescreen TV: Select “16:9 Wide”. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 6

Recording Information This DVD recorder can record to DVD-R and DVD-RW discs.When recording, you will need to select a recording format between Video mode and VR mode depending on the disc format.The disc format for DVD-R is always “Video format,” so a recording format will be “Video mode”. On the other hand, when recording to DVD-RW, a recording format will be “Video mode” or “VR mode” because a disc format is available between “Video Recording format” and “Video format” for DVD-RW. * This unit cannot record on the following discs. • DVD-RW Ver 1.2 / 2-4x CPRM compatible • DVD-R General Ver 2.0 / 8x About Video mode and VR (Video Recording) mode Video mode is the same recording format as DVD- Video discs purchased locally, so that you can play in most DVD players.To play in other DVD players, you will need to finalize (see page 39). Unless final- ized, you can play, record additionally or edit discs recorded in Video mode with this unit. VR (Video Recording) mode is a basic recording format for DVD-RW.You can record and edit repeatedly. DVD players with are capable of playing DVD-RW recorded in VR mode. Recording speed You can select a recording speed among 6 options, and the recording time will depend on the record- ing speed you select as follows. *This table is designed for a new single-sided 12cm disc as the standard.The recording time are esti- mates and actual recording time may differ. *The audio and video quality is getting poorer as the Recording time becomes longer. *Discs recorded in SLP or SEP on this recorder may not be played back on other DVD recorders or DVD players. Restrictions on recording You cannot record copy-protected video using this DVD recorder. Copy-protected video includes DVD-Video discs and some satellite broadcasts. If copy-protected material is encountered during a recording, recording will pause or stop automatically and an error message will be displayed on-screen. Video that is “copy-once only” can only be recorded using a DVD-RW disc in VR mode with CPRM (see below). When recording a TV broadcast or through an external input, you can display copy control informa- tion on screen. What is “CPRM”? CPRM is a copy protection system with scram- ble system regarding the recording of “copy once” broadcast programs. CPRM stands for Content Protection for Recordable Media. This DVD recorder is CPRM compatible, which means that you can record copy-once broad- cast programs, but you cannot then make a copy of those recordings. CPRM recordings can only be made on DVD-RW discs formatted in VR mode, and CPRM recordings can only be played on players that are specifically compati- ble with CPRM. Recording speed XP SP LP EP SLP SEP Recording time * 60 min 120 min 240 min 360 min 480 min 600 min Video/Sound Quality Disc type Disc format Video mode VR mode Video mode Functions Playing, limited recording, limited editing Playing, recording, Original/Playlist editing Playing, limited recording, limited editing DVD-RW DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-R DVD-R
 Logo Attributes 8cm/12cm, single-sided, single layer disc Approx. max. recording time (SEP mode): 600 minutes (4.7GB) (for 12cm) 180 minutes (1.4GB) (for 8cm) 8cm/12cm, single-sided, single layer disc Approx. max. recording time (SEP mode): 600 minutes (4.7GB) (for 12cm) 180 minutes (1.4GB) (for 8cm) DVD-RW DVD-R 4.7

Some satellite broadcasts include copy-protected information. For recording these, refer to the fol- lowing. Making discs playable in other DVD player (Finalize) After recording, you must finalize disc in order to play on anyother unit. (Refer to page 39.) After finalizing: • Once DVD-RW/R (Video mode) is finalized, you cannot record additionally or edit. • Even if DVD-RW (VR mode) is finalized, you can record additionally or edit the disc. • When DVD-RW/R (Video mode) is finalized, title menu will be created automatically. To play in other DVD players, finalize discs recorded on this unit with the following condition. Disc type Mode DVD-RW ver.1.1 ver.1.1 CPRM compatible Video mode VR mode DVD-R ver.2.0 Video mode Disc type / format Copy-free Copy-once Copy- prohibited Recordable Not Recordable DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-R DVD-R ver.1.1 ver.1.1 CPRM compatible ver.1.1 ver.1.1 CPRM compatible ver.2.0 Note • The audio and video quality is getting poorer as the Recording time becomes longer. • This recorder cannot record CD-RW or CD-R discs. • DVD-RW/R and CD-RW/R discs recorded using a personal computer or a DVD or CD recorder may not play if the disc is damaged or dirty or if there is dirt of condensation on the player’s lens. • If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software pub- lisher for more detailed information.) • Discs recorded in Video mode on this DVD recorder cannot record additionally using other DVD recorders. • A DVD-RW disc formatted with this unit cannot be used in other DVD recorders without any recording using this unit. • Since the recording is made by the variable bit rate (VBR) method, depending on the picture you are recording, the actual remaining time for recording may be a little shorter than the remaining time displayed on the OSD. Information on DVD recording (cont’d) Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español This Unit DVD player Not Playable Playable

28 Formatting a disc Recording When inserting a blank disc, the DVD recorder starts to initialize the blank disc. After that, you can record to the disc with the recording format selected in SETUP menu. You are allowed to set a specified time for chapter marks. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Recording” using K / L / { / B buttons, then press ENTER button. Recording menu will appear. 4 Select “DVD-RW Recording Format” using K / L buttons, then press ENTER button. Option window will appear. VR mode has been selected as the default. 5 Select “Video mode” or “VR mode” using K / L buttons, then press ENTER button. The recording mode will be set. Setup > Recording Auto Chapter Timer Programming Video mode DVD Player Compatibility mode. VR mode Editing possibility mode. DVD-RW Recording Format VR mode 10 minutes Video mode VR mode Setup > Recording Auto Chapter Timer Programming VR mode DVD-RW Recording Format 10 minutes Setup Playback Setting Setup Menu DVD-RW DVD-RW VR DVD-RW DVD-RW Video Note • When inserting a blank DVD+R or DVD+RW disc, the error message ("Disc Error") will appear.This DVD recorder is not compatible with a DVD+RW/R disc. • PLAYLIST will be created automatically when recording on DVD-RW in VR mode. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5

Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 6 Select “Auto Chapter” using K / L buttons, then press ENTER button. Option window will appear. “10 minutes” has been selected as the default. 7 Select a desired time option using K / L buttons, then press ENTER button. Chapter marks will be put as you specified. 8 Press SETUP button to exit. Setup > Recording Auto Chapter Timer Programming DVD-RW Recording Format VR mode 10 minutes OFF 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes 6 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 8 7 Note • The time for chapter marks is not accurate in Video mode. • A blank chapter may be creat- ed depending on the remain- ing time of the disc.

Recording If you are using a DVD-RW disc, by default it will be VR mode.You can change this to Video mode from SETUP menu. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. * VR mode only 3 Select “Format” using K / L buttons, then press ENTER button. Option window will appear. * VR mode only 4 Select “Yes” using { / B but- tons, then press ENTER but- ton. Option window will appear. * VR mode only 5 Select “Yes” using { / B but- tons, then press ENTER but- ton. Formatting will start. 6 Formatting is complete. 100% will be indicated. Formatting 100% Formatting 58% Disc Edit Format Finalize Yes No Disc Protect OFF ON Are you sure? Yes No Disc Edit Format Finalize Yes No Disc Protect OFF ON Disc Edit Format Finalize Disc Protect OFF ON Setup Menu DVD-RW DVD-RW VR DVD-RW DVD-RW Video Reformatting a disc Note • When you reformat the disc, the contents of the disc will be erased. • If you want to cancel format at step 5, select "No". POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 This operation may take a while to be completed.

Connections Getting started Changing the SETUP menu Others Español Note • Recording starts immediately and continues until the disc is full or you stop recording. • When the clock setting has not been made, the space for a date and time of title names in the original or playlist will be blank. • When you record a TV pro- gram which has Stereo and SAP audio on a DVD-RW/R (Video mode), you have to select the TV channel audio (Stereo or SAP) beforehand. Only the selected channel audio will be recorded. Refer to “Selecting the TV stereo or SAP” on page 20 for more details. • You cannot mix two formats on one DVD-RW disc. When you load a disc once recorded before, the record- ing format cannot be changed even if you change it in SETUP menu. • You cannot change the recording speed during the REC pause mode. • You can change a channel during the REC pause mode. Follow the steps below to record TV programs. 1 Turn on the DVD recorder and load a recordable disc. Make sure that the TV input is set on the DVD recorder. 2 Select a recording speed using REC MODE button. Refer to “Recording speed” on page 26. 3 Make sure that the recording format is set to the desired mode. Refer to “Formatting a disc” on pages 28-30. When a DVD-RW disc is loaded: You can choose Video mode or VR mode from SETUP menu. “VR mode” has been selected as the default. Refer to “Choosing the recording format of a blank disc” on pages 28-29. When a DVD-R disc is loaded: DVD-R discs will always be in Video mode. 4 Select a desired channel to record using CH K / L but- tons or number buttons. 5 Press REC button to start recording. REC mark will be displayed for 5 seconds. To pause the recording, press PAUSE F button. Press REC but- ton to restart the recording. 6 Press STOP C button to stop the recording. This operation may take a while to be completed. I CH 1 SP 2:01 Rem. This operation may take a while to be recognized. DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 5 2 4 4 5 6

Recording Note • You cannot check the record- ing sound with the Rec moni- tor function. You can confirm the recording pic- ture quality with the recording speed you have selected before attempting to record to a DVD disc. 1 While the DVD recorder is in STOP or REC with a DVD disc to record inserted, press REC MONITOR button. The TV program will be on the screen in the recording picture quality with the recording speed you have selected. If you want to change the recording speed, press REC MODE button repeatedly. The recording speed will be changed as you press the button as shown. Refer to “Recording speed” on page 26. • You cannot change the record- ing speed during recording. 2 Press REC MONITOR button again to exit. XP SP LP EP SLP SEP CH 18 Rec Monitor XP DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video Checking the recording picture quality POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 1

Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Note • The remaining recording time will appear on the display panel during an one-touch timer recording. Press DIS- PLAY button to see it on the TV screen. • You cannot pause a one-touch timer recording. • Unlike a timer recording, you can perform the following operations during a one-touch timer recording. - Turning the power off - Using REC, STOP C, or RETURN buttons. • The unit will be turned off automatically under the fol- lowing conditions. 1) No space remained on the disc. 2) When a power failure occurs. This is a simple way to set the recording time in blocks of 30 minutes. Check that the disc you are recording onto has enough space for the time you set. When the recording finishes the recorder automatically goes into standby. 1 Turn on the DVD recorder and load a recordable disc. Make sure that the TV input is set on the DVD recorder. 2 Select a recording speed using REC MODE button. Refer to "Recording speed" on page 26. 3 Make sure that the recording format is set to the desired mode. Refer to "Formatting a disc" on pages 28-30. When a DVD-RW disc is loaded: You can choose Video mode or VR mode from SETUP menu. "VR mode" has been selected as the default. Refer to pages 28-29 "Choosing the recording format of a blank disc." When a DVD-R disc is loaded: DVD-R discs will always be in Video mode. 4 Select a desired channel to record using CH K / L but- tons or number buttons. 5 Press REC button, then press REC button repeatedly until a desired recording time (30 minutes to 4 hours) appears on the TV screen. Recording will start. When the DVD recorder reaches the specified time, it will be turned off automatically. To change the recording length during the one touch timer recording, press REC button repeatedly until the desired length appear. To cancel the one-touch timer recording within the specified time, press STOP C button. 0:30 (Normal Recording) 4:00 3:30 1:00 I 0:30 This operation may take a while to be recognized. DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 5 4 2 5 This operation may take a while to be completed.

record up to 8 programs, up to a year in advance. Daily or weekly program recordings are also avail- able. • Be sure to set the clock before making a timer programming. • Insert a recordable disc. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Recording” using K / L / { / B buttons, then press ENTER button. Recording menu will appear. 4 Select “Timer Programming” using K / L buttons, then press ENTER button. Timer Programming list will appear. 5 Select the program which is not set up using K / L but- tons, then press ENTER but- ton. 6 Enter the date using K / L buttons, then press B button. e.g. January 1st 7 Enter the time to start and to end using K / L buttons, then press B button. Date Start End CH 1. 2. 3. 4 - - - - - - - - : - -AM Speed CH8 10 :00PM JAN/12 Setup > Recording > Timer Programming Daily L L MON-SAT JAN/01 DEC/31 L MON-FRI L SAT L FRI L SUN L L Setup > Recording > Timer Programming Date Start End CH Speed 1. 2. 3. 4. - - - JAN / 01 - - - - - - - - : - -AM - - : - -AM CH8 Setup > Recording > Timer Programming Date Start End CH Speed 1. 2. 3. 4 - - - - - - - - - Setup > Recording Auto Chapter Timer Programming VR mode DVD-RW Recording Format 10 minutes Setup Playback Setting Setup Menu DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L Note • If you have not set the clock yet: A clock setting window will appear after step 4. Continue with the step 4 in “Auto Clock Setting” on page 21 or “Manual Clock Setting” on page 22 before making a timer programming. • Press { or B buttons to move the cursor to the left and the right in the timer programming menu. 1 2 3 4 5 You can choose the timer programming menu by press- ing TIMER PROG. button. In this case, continue with step 5. 7 6 When pressing L button at the current date, timer recording mode will change as follows.

Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 8 Select the channel number to record using K / L buttons, then press B button. To record from external input, L1 or L2. 9 Select a recording speed using K / L buttons. Refer to “Recording speed” on page 26. 10 Press ENTER button when all information required is entered. Your program setting will be stored. • To set another program, repeat steps 5 to 10. • To exit, press SETUP button. 11 Press POWER button to turn off. indicator will appear on the front display. Date Start End CH Speed 1. XP 2. - - - CH8 10:30PM 10:00PM JAN/12 Setup > Recording > Timer Programming Date Start End CH Speed 1. 2. - - - CH8 10:30PM 10:00PM JAN/12 Setup > Recording > Timer Programming POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 11 8 9 1 Press POWER button so that indicator disappears from the front display. 2 Press TIMER PROG. button. Timer Programming list will appear. 3 Check the information on the list you will need. 4 To clear the timer programming, select your desired program using K / L buttons.Then, CLEAR button. To correct the timer program- ming, select your desired pro- gram using K / L buttons.Then, press ENTER button. Next, cor- rect the timer programming by using press K/L/{/B buttons. Finally, press ENTER button again. 5 Press TIMER PROG. button to exit. 6 Press POWER button to return to the timer standby mode. Date Start End CH Speed 1. XP 2. - - - CH8 10:30PM 10:00PM JAN/12 Setup > Recording > Timer Programming Checking, canceling, or correcting the timer programming information Note • Press TIMER PROG. button to check the timer programming in process. When the timer recording is proceeding, that program will be highlighted with red. In this case, you cannot select any other program. 10 Note • After step 11, the DVD recorder will be turned on automatically 2 minutes in advance of the recording time to start and waits to start. Then the recording will start at the recording time you set. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 5 6 Press C (STOP) button on the front panel of the main unit. STOP C button on the remote control is not effective. To stop the timer recording in process 4 4

PROG. 2 PROG. 1 When the End time of the programming currently being recorded and the Start time of the subsequent program are same: If PROG. 1 is a DVD recording program, the beginning of the PROG. 2 may be cut off. The amount of time cut off differs depending on the recorded media. For example, if both PROG. 1 and PROG. 2 are DVD recordings, the first 30 seconds (at the longest) will be cut off PROG. PROG. 1 PROG. 2 Actual recording PROG. 2 When the recording time is entirely overlapped: However, if you turn the power off for timer standby within 2 minutes to the Start time for PROG. 1, PROG. 1 will be recorded first, and the recording of PROG. 2 will start after the recording of PROG. 1 is completed. PROG. 1 PROG. 2 Actual recording PROG. 2 PROG. 1 When the recording time is partially overlapped: PROG. 1 will start after PROG. 2 is complete to be recorded. However, PROG. 1 will be recorded if you turn the power off for timer standby within 2 minutes to the Start time for PROG. 1. The first 30 seconds (at the longest) will be cut off PROG. 1 ex.1 PROG. 2 Actual recording PROG. 1 PROG. 2 PROG. 1 PROG. 2 Actual recording PROG. 1 PROG. 2 PROG. 3 ex. 2 A programming set previously has priority When the starting time is the same: A program set previously (PROG. 1) has priority. When some programming have been made at the end time of the programming currently being recorded: A program set previously (PROG. 2) has priority. The first 30 seconds (at the longest) will be cut off The first 30 seconds (at the longest) will be cut off Hints for timer recording • If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost. • If a disc is not on the tray, the indicator flashes and timer recording cannot be performed. Please insert a recordable disc. • When all the timer recording is completed, the indicator flashes.To play or eject the recorded disc, press POWER button first, and then press PLAY B or OPEN/CLOSE A button. • During timer recording or timer standby ( indicator is on the front display), any operations on the unit will not be available.To make these operations available, cancel the timer recording or timer standby first ( indicator disappears). • To cancel the timer standby mode, press POWER button. • When the Start and the End time are the same, the length of the recording will be set for 24 hours.When the disc reaches at the end during the recording, the DVD recorder turns itself off. • When the programmed Start and End time are earlier than the current time, the recording will be set on the same date in the next year. • If your programmed Start time is within 2 minutes from the current time, the power will turn on for recording standby right after you turn the power off. • If the Start time is earlier and the End time is later than the current time, the recording will start right after you turn the power off. This unit records the programs according to priority if the timer programmings are overlapped.The timer programming set previously has priority. A timer recording of lower priority will be canceled, start from the middle or stop on the way. Check the overlapped timer programmings and change the priority if necessary. The priority of overlapped settings 36 Timer recording (cont’d) Recording Note • When the recording time of two programs are overlapped, or the End time of a program and the Start time of another is the same, the first 30 sec- onds (at the longest) of the subsequent program will be cut off.

LINE1 (Rear). Use commercially available S-Video or Video cable and an Audio cable for this connection. DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video Connection to an external source 1. Press SETUP button to display SETUP/DISC menu. 2. Select “SETUP” using { / B buttons, then press ENTER button. 3. Select “Select Video” using K / L / { / B buttons, then press ENTER button. 4. Select “L2 (Front)” using K / L buttons, then press ENTER button. 5. Select the input jack type to connect using K / L buttons, then press ENTER button. If you want to use S-VIDEO INPUT, select “S-Video In”. If you want to use VIDEO INPUT (Composite), select “Video In”. Setup > Select Video L1 (Rear) L2 (Front) S-Video In Video In Setup > Select Video L1 (Rear) L2 (Front) Video In Video In Video In S-Video In Setup > Select Video L1 (Rear) L2 (Front) Video In Video In 1. Press SETUP button to display SETUP/DISC menu. 2. Select “SETUP” using { / B buttons, then press ENTER button. 3. Select “Select Video” using K / L / { / B buttons, then press ENTER button. 4. Select “L1 (Rear)” using K / L buttons, then press ENTER button. 5. Select the input jack type to connect using K / L buttons, then press ENTER button. If you want to use S-VIDEO INPUT, select “S-Video In”. If you want to use VIDEO INPUT (Composite), select “Video In”. Setup > Select Video L1 (Rear) L2 (Front) Video In S-Video In Setup > Select Video L1 (Rear) L2 (Front) Video In Video In Video In S-Video In Setup > Select Video L1 (Rear) L2 (Front) Video In Video In or Settings for an external source Recording Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Front of DVD recorder Rear of DVD recorder DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO INPUT COMPONENT VIDEO OUTPUT TV ANTENNA OUTPUT R R L L AUDIO VIDEO 1 2 (L1) VIDEO S-VIDEO S-VIDEO PR/CR PB/CB Y REC/OTR OPEN/CLOSE AUDIO INPUT R L (L1) VIDEO S-VIDEO To LINE 2 IN To LINE 1 IN Another source (VCR camcorder etc.) VIDEO S- VIDEO AUDIO R L OUTPUT Audio cable S-Video cable VIDEO S -VIDEO AUDIO L R OUTPUT S-Video cable Audio cable Video cable Video cable or or

Recording Before recording from an external source, see the instructions for the connection on page 37. DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video Recording from an external source 1. Turn the TV and the DVD recorder on, and be sure to select the input of the TV to which the DVD recorder is connected. 2. Press OPEN/CLOSE A button to open the disc tray, then place the disc to record properly. 3. Press OPEN/CLOSE A button to close the disc tray. 4. Select the input of the DVD recorder which the external equipment is connected. (L2 or L1) • To use the input jacks on the back of this unit, select “L1” position by pressing [0], [0], [1] on the remote control or the CH L / K buttons. • To use the input jacks on the front of this unit, select “L2” position by pressing [0], [0], [2] on the remote control or the CH L / K buttons. 5. Select a recording speed using REC MODE button. Refer to “Recording speed” on page 26. 6. Press REC button on the DVD recorder to start recording. 7. Press Play button on the external source to record from. 8. Press STOP C button on the DVD recorder to stop record- ing. This operation may take a while to be completed. XP SP LP EP SLP SEP This operation may take a while to be recognized. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 6 5 1 2 8 4 3

Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Note • Finalizing discs in Video mode automatically creates title menus. • Once you have finalized a disc recorded in Video mode, you cannot edit or record anything else on that disc. Discs recorded in VR mode can still be recorded and edited on this recorder even after being finalized. • When you insert a DVD-RW disc finalized with this DVD recorder,“Undo Finalize” will appear instead of “Finalize”. To release the finalizing for the disc, select “Undo Finalize” at step 3. Disc Edit Format Undo Finalize You will need to finalize the discs recorded in Video mode to play in other DVD players. Details are on pages 26-27. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. * VR mode only 3 Select “Finalize” using K / L buttons, then press ENTER button. Option window will appear. * VR mode only 4 Select “Yes” using { / B but- tons, then press ENTER but- ton. Finalizing will start. 5 Finalizing is complete. Finalizing 100% To cancel finalizing... • To cancel finalizing at step 4, press STOP C button, select “YES”, then press ENTER button. Finalizing is cancelled and the DVD recorder will be in stop mode. • If appear when pressing STOP button, you cannot cancel finalizing because the finalizing has been in certain progress. • When selecting “No” and press ENTER or RETURN button, finalizing will be continued. • You cannot cancel finalizing the DVD-R disc when it has been started. Finalizing 58% Disc Edit Format Finalize Yes No Disc Protect OFF ON Disc Edit Format Finalize Disc Protect OFF ON Setup Menu DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 4 2 3 4 This operation may take a while to be completed.

Recording To prevent accidental recording, editing, or erasing the titles, you can protect them from DISC menu. 1 Press SETUP button to dis- play SETUP/DISC menu. SETUP/DISC menu will appear. Screen: 2 Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 3 Select “Disc Protect OFF ➔ ON” using K / L buttons, then press ENTER button. Option window will appear. 4 Select “Yes” using { / B but- tons, then press ENTER but- ton. A disc will be protected. Writing to Disc 58% Disc Edit Format Finalize Disc Protect OFF ON Yes No Disc Edit Format Finalize Disc Protect OFF ON Setup Menu DVD-RW DVD-RW VR POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 This operation may take a while to be completed. Note • The Disc Protect setting is available only when a disc with VR mode is inserted. To cancel the disc protect: • When you insert a disc pro- tected with this unit,“Disc Protect ON →OFF” will appear instead of “OFF → ON”. To release the protect for the disc, select “Disc Protect ON →OFF” at step 3, then select “Yes”. Disc Edit Format Finalize Disc Protect ON OFF Yes No

Playing discs Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Before you attempt to play DVD discs, read the following information. Press DISPLAY button to call up the display menu.This menu will give you the information on the playing disc. Some operations are available while disc is playing. 1. Indicates a disc type and a format mode. 2. Indicates a recording speed and possible recording time. / Indicates a channel number. 3. Indicates a title number, chap- ter number, and the time lapse of disc play. 4. Each icon means: : Search : Audio : Subtitle : Angle (except VR mode) : Repeat : Marker : Noise Reduction : Zoom DVD-RW SP 1:25 Rem. Video mode 1 1 00:00:00 1 3 2 4 Guide to displays Playable discs This DVD recorder is compatible to play the follow- ing discs. To play a DVD, make sure that it meets the require- ments for Region Codes and Color Systems as described below. Discs that have the following logos will play on the DVD recorder. Other Disc types are not guaranteed to play. Note: The following discs can be played on this unit but their performance is not guaranteed : • DVD-RW Ver 1.2 / 2-4x CPRM compatible • DVD-R General Ver 2.0 / 8x Color systems DVDs are recorded in different color systems throughout the world.The most common color sys- tem is NTSC (which is used primarily in the United States and Canada). This DVD Recorder uses NTSC, so DVDs you play must be recorded in the NTSC system.You cannot play DVDs recorded in other color system . Region codes This DVD recorder has been designed to play DVD discs with Region One (1). DVDs must be labeled for ALL regions or for Region 1 in order to play on the DVD recorder.You cannot play DVDs that are labeled for other regions. Look for the symbols below on your DVDs. If these region symbols do not appear on your DVD, you cannot play the DVD in this DVD recorder. The number inside the globe refers to region of the world. A DVD labeled for a specific region can only play on the DVD recorder with the same region code. Hint for DVD playback The contents of DVD disc are generally divided into titles.Titles may be further subdivided into chapters. Logo Disc DVD VIDEO DVD-RW (VIDEO/VR mode) DVD-R (VIDEO mode) CD-DA (AUDIO CD) CD-R (CD-DA FORMAT, MP3 files) CD-RW (CD-DA FORMAT, MP3 files) DVD+RW (VIDEO mode) DVD+R (VIDEO mode) Start Rec. Stop/Start Stop Rec. Title 1 Title 2 Chapter 1 Chapter 1 Chapter 2 Chapter 3 Chapter 2

and DVD-RW (Video mode) discs which are already final- ized, a title list will be dis- played instead of thumbnails. • You can resume play from where you stopped playing the disc. (Resume play) Refer to page 46 for details about resume play. • Some discs may start playing automatically. 1 XP 2 3 4 5 6 7 8 CH96 12:24AM JAN/1 Title Menu 1 Press POWER button on the remote control or the front panel of the DVD recorder. When you are playing a DVD, turn the TV on and be sure to select the input to which the DVD recorder is connected. 2 Press OPEN/CLOSE A but- ton to open the disc tray. The disc tray will open. 3 Place the disc onto the disc tray with its label facing up and make sure to align the disc to the disc tray guide. 4 Press OPEN/CLOSE A but- ton to close the disc tray. 5 Press TOP MENU button to display the title menu. You can change “Original” or “Playlist” of VR mode using MENU / LIST button. Video mode: VR mode: MENU / LIST button 6 Select a desired title using K / L / { / B buttons, then press ENTER button. Playing will start. 7 Press STOP C button to stop play. To eject the disc, press OPEN/CLOSE A button to open the disc tray, then remove the disc before turning the DVD recorder off. Playlist 5 4 1 1 3 2 JAN/1 12:00AM JAN/1 3:00AM JAN/1 1:00AM JAN/1 2:00AM JAN/1 4:00AM Original 1 1 3 2 5 4 JAN/1 12:00AM JAN/1 3:00AM JAN/1 1:00AM JAN/1 2:00AM JAN/1 4:00AM Title List 1 1 3 2 5 4 JAN/1 12:00AM JAN/1 3:00AM JAN/1 1:00AM JAN/1 2:00AM JAN/1 4:00AM disc tray guide DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 5 7 1 2 4 5 6 Playback This operation may take a while to be recognized. 7

Playing discs Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 1 Press POWER button on the remote control or the front panel of the DVD recorder. When you are playing a DVD, turn the TV on and be sure to select the input to which the DVD recorder is connected. 2 Press OPEN/CLOSE A but- ton to open the disc tray. The disc tray will open. 3 Place the disc onto the disc tray with its label facing up and make sure to align the disc to the disc tray guide. 4 Press PLAY B button to start playing. Playing will start. If you are playing a DVD-Video disc, a menu may appear. Refer to pages 44-45 for details about a disc menu. 5 Press STOP C button to stop playing. MP3 MP3 CD CD DVD-V DVD-V Note • Some discs may start playing automatically. Note • The audio source of MP3 files cannot be recorded as digital sound by an MD or DAT deck. • Files whose extension is other than “.mp3(MP3)” will not be listed in the MP3 menu. • Some unplayable folders or tracks may be listed in the MP3 menu due to the record- ing status. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 5 4 For MP3 playback REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN MENU/LIST TOP MENU SPACE 0 F { B FWD g STOP C PLAY B REV h H G K L 1 2 1 In stop mode, press TOP MENU button to call up the MP3 menu. • To exit the menu, press TOP MENU button again. 2 Press K / L buttons to select a desired folder (group) or track, then press ENTER button. When selecting track: Playback will start. When selecting the folder: The files in folder will appear. Press K / L buttons to select the track or fold- er you want,then press ENTER button. • Press PLAY B,ENTER or B button to move to the lower hierarchies. • Press s button or RETURN button to the previous hierarchy. • Press STOP button to return to the first item. Hints for MP3 files: • Folders are known as Groups, files are known as Tracks. • Folders are accompanied by icon. • MP3 files are accompanied by icon. Reproduction will start from the select- ed track and go to the next one in turn. • The system can recognize up to 255 groups (or folders) and up to 255 tracks. • The name of group and track can be displayed in up to 32 charac- ters. Unrecognizable characters will be replaced with asterisks. • If there are no files in the folder, “No Files” will be displayed. This unit recommends the files record- ed under the following circumstances: • Sampling frequency:44.1kHz or 48kHz. • Constant bit rate:112kbps - 320kbps. FOLDER NAME 1 FOLDER NAME 2 FOLDER NAME 3 FOLDER NAME 4 FOLDER NAME 5 FOLDER NAME 6 1 FILE NAME 1 2 FILE NAME 2 DISC NAME List of MP3 Files 1/2

Playing discs Note • Menus vary among discs. Refer to the information accompanying the disc for details. Playing discs using the disc menu A DVD disc contains a disc menu that describes the contents or allows you to customize the play- back. For example, the menu may offer choices for subtitle lan- guages, special features, or chapter selection. Sometimes these are displayed automatically when you start play- back, otherwise only appear when you press MENU / LIST button. 1 Press MENU / LIST button. The DVD main menu will appear. If the feature is not available, may appear on the TV screen. 2 Select an item using K / L / { / B buttons, then press ENTER button to confirm. Continue this step to set up all the features you want or to start playing the disc from the menu. MENU / LIST button: Displays a DVD disc menu which varies with the disc and may be the same as the ‘Title menu.’ K / L / { / B buttons: Moves the cursor around screen. Enter button: Selects the currently highlighted menu option. Number buttons: Selects a numbered menu option (some discs only). (Press ENTER button after.) 3 Press MENU / LIST button to exit the menu. DVD-V DVD-V POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 3 2 1 2

Playing discs Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Note • The TOP MENU button will not always be active with all DVDs. • Menus vary among discs. Refer to the information accompanying the disc for details. Playing discs using the title menu Some DVDs have a title menu, which lists the titles available on them. It helps you to start play at a specific title. 1 Press TOP MENU button. The title menu will appear. If the feature is not available, may appear on the TV screen. 2 Select a title to play using the K / L / { / B buttons, then press ENTER button. Play will begin at the title you selected. TOP MENU button: Displays the ‘Title menu’ of a DVD disc which varies with the disc. K / L / { / B buttons: Moves the cursor around screen. Enter button: Selects the currently highlighted menu option. Number buttons: Selects a numbered menu option (some discs only). (Press ENTER button after.) 3 Press TOP MENU button to exit the title menu. DVD-V DVD-V POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 3 2 1 2

you stopped playing the disc last. 1 During play, press STOP C button. The resume message will appear. Screen: 2 Press PLAY B button. In a few seconds, play will resume from the point at which it stopped last.You can resume play at the same point even if you turn off the DVD recorder. To cancel the resume play and start playing the disc from the beginning, press STOP C button the second time while the play is stopped. Resume ON MP3 MP3 CD CD DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V Fast forward / Fast reverse 1 During play, press FWD D or REV E button. Every time you press FWD D or REV E button, approximate speed will be changed as follows. For DVD discs, sound will be output during fast forward in x2 only if you set “Fast Forward with Audio” to “ON” for the “Playback” setting in the SETUP menu. Fast forward or fast reverse playback across titles (for DVD discs) or tracks (for MP3) is not possible. For Audio CDs, approximate speed is fixed at x8 with sound. For MP3 files, approximate speed is fixed at x16. To return to the normal play, press PLAY B button. x20 Normal speed playback x2 x20 x5 x40 x40 FWD g REV h FWD g REV h FWD g REV h FWD g REV h FWD g REV h FWD g REV h MP3 MP3 CD CD DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V Note • Forward/reverse speed will be indicated with icons as fol- lows. Forward (Approx. Speed) x2: x20: x40: Reverse (Approx. Speed) x5: x20: x40: REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 2 REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR MENU/LIST TOP MENU SPACE 4 5 6 7 8 9 0 F { B FWD g STOP C PLAY B REV h H G CH GHI JKL MNO PQRS TUV WXYZ K L 1 1 1 Note • For MP3 files, playback will resume from the beginning of the track at which playback was stopped.

Playing discs Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Skipping TV commercials during play You can skip TV commercials by pressing CM SKIP button, so that you can enjoy the recorded pro- grams without interrupting. 1 During play, press CM SKIP button. Normal play will start at 30 sec- onds ahead from the point you press CM SKIP button. Every time you press CM SKIP button, the searching point will be extended by 30 seconds ahead. You can press up to 6 times (180 seconds). e.g. Press CM SKIP button once (forwarding 30 seconds.) Playback will restart automatically. B CM Skip 30 sec. DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video Pause 1 During play, press PAUSE F button. Play will pause and sound will be muted. 2 Press PLAY B button to resume play. MP3 MP3 CD CD DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2

Playing discs Step by step playback 1 During play, press PAUSE F button. Play will pause and sound will be muted. 2 Press SKIP G button repeatedly. The play will advance one frame (or step) at a time when you press the SKIP G button with the sound muted. To play step by step back- ward: Press SKIP H button repeatedly. Every time you press the button, the play will go backward by one frame. 3 Press PLAY B button to resume play. DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V Slow forward / Slow reverse play 1 During play, press PAUSE k button, then press FWD D or REV E button. Every time you press FWD D or REV E button, approximate speed will be changed as follows. (The sound will remain muted.) To return to the normal play, press PLAY B button. x1/8 Pause x1/16 x1/8 x1/16 x1/2 x1/4 FWD g REV h FWD g REV h FWD g REV h FWD g REV h FWD g REV h FWD g REV h DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V Note • Forward/reverse speed will be indicated with icons as fol- lows. Forward (Approx. Speed) x1/16: x1/8: x1/2: Reverse (Approx. Speed) x1/16: x1/8: x1/4: POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 3 2 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ENTER REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K 1 1 1 1

Playing discs Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Note • When selecting a smaller factor than the current one, the zoom area will not be displayed. • To remove the zoom menu, press ZOOM button again at step 1. • To cancel the zoom function, select x1.0 using { / B buttons, then press ENTER button. Zoom 1 During play, press ZOOM but- ton. Zoom menu will appear. Screen: There are four options (x1.0,x1.2,x1.5 and x2.0), these are displayed excluding the cur- rent zoom rate. 2 Select a desired zoom factor to zoom using { / B buttons, then press ENTER button. The zoom area will be displayed. 3 Select a desired zoom position using K / L / { / B buttons, then press ENTER button. The zoom play will start. 1 1 x1.2 x1.5 x2.0 01:23:45 DVD-Video B DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V SETUP REPEAT ZOOM ENTER RETURN MENU/LIST TOP MENU { B FWD g STOP C PLAY B REV h K L 1 2 3 Marker Setup This feature allows you to assign a specific point on a disc to be called back later. 1 During play, press DISPLAY button. The display menu will appear. Screen: 2 Select icon using { / B buttons, then press ENTER button. Marker setup menu will appear. Screen for DVD: Screen for CD: 3 Select a desired marker num- ber using { / B buttons. When it reaches the desired point, press ENTER button. 4 To return to the marker later, select the desired marker number using { / B buttons, then press ENTER button. 1 01:23:45 Audio CD 1 2 3 4 5 6 1 1 01:23:45 DVD-Video 1 2 3 4 5 6 1 1 01:23:45 DVD-Video CD CD DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V Note • To clear a marker, select the marker number to be cleared, then press CLEAR button. • All markers will be erased when you operate these opera- tions listed below. – Opening the disc tray. – Turning off the power. – Recording to a recordable disc. – Changing the mode between Original and Playlist.(VR mode) •You can mark up to 6 points. POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 3 4 1

1 During play, press SKIP G button to skip the current title or chapter and move to the next. The title or chapter will move forward by one at a time. To go back to the previous title or chapter, press SKIP H button.The title or chapter will move backward one title at a time. DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE REC MONITOR OPEN/CLOSE TIMER PROG. SPACE 1 2 3 4 5 6 7 8 9 0 F A FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ 1 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 2 1 Using DISPLAY button 1 During play, press DISPLAY button. The display menu will appear. Screen: 2 Select icon using { / B buttons, then press ENTER but- ton. ‘T’ for title will be highlighted. Title: Enter a desired title number to search using K / L buttons or number buttons, then press ENTER button. Title search will start. Chapter: To move to ‘C’ for chapter, press B button. Enter a desired chapter number to search using K / L buttons or number buttons, then press ENTER button. Chapter search will start. 1 1 01:23:45 DVD-Video

Connections Getting started Changing the SETUP menu Others Español Track search Using SKIP H / G buttons 1 During play, press SKIP G button to skip the current track and move to the next. The track will move forward one at a time. To go back to the previous track, press SKIP H button.The track will move backward one at a time. MP3 MP3 CD CD REC MODE CLEAR CM SKIP SKIP REC PAUSE REC MONITOR SPACE 1 2 3 4 5 6 7 8 9 0 F FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ 1 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L Time search 1 During play, press DISPLAY button. The display menu will appear. Screen for DVD: Screen for CD: 2 Select icon using { / B buttons, then press ENTER button. ‘T’ for title or track will be high- lighted. To move to the clock icon, press B button. 3 Enter a desired time to search using K / L buttons or number buttons, then press ENTER button. Time search will start. 1 01:23:45 Audio CD 1 1 01:23:45 DVD-Video CD CD DVD+R DVD+R DVD+RW DVD+RW Video DVD-V DVD-V DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-R DVD-R Note • Time search function is avail- able only in the same track or title. 3 2 1 Using DISPLAY button 1 During play, press DISPLAY button. The display menu will appear. Screen: 2 Select icon using { / B buttons, then press ENTER button. ‘T’ for track will be highlighted. 3 Enter a desired track number to search using K / L buttons or number buttons, then press ENTER button. Track search will start. 1 01:23:45 Audio CD POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 3 2 1

only be set with in the cur- rent title (for DVDs), or cur- rent track (for Audio CDs). • To cancel the repeat playback, select OFF at step 2.The repeat setting will also be cancelled when you stop play- back. • You cannot select “Group” during the random playback of MP3 files. Repeat play 1 During play, press REPEAT button. Repeat menu will appear. Screen: 2 Select a desired option to repeat using K / L buttons, then press ENTER button. The selected repeat play will start. Title: The current title will be played repeatedly. (DVD only) Chapter: The current chapter will be played repeatedly. (DVD only) All: The current disc will be played repeatedly. (CD, MP3, DVD-RW (VR mode) only) A-B: The A-B point will be played repeatedly. When pressing ENTER button while A-B is highlighted, the start- ing point (A) will be decided. Press ENTER button again to select the ending point (B). Track: The current track will be played repeatedly. (CD, MP3 only) Group: The current group will be played repeatedly. (MP3 only) OFF Track All Group 114 00:00:30 MP3 OFF Track All A-B 2 00:00:30 Audio CD OFF Title Chapter A-B 1 1 01:23:45 DVD-Video MP3 MP3 CD CD DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR MENU/LIST TOP MENU SPACE 7 8 9 0 F { B FWD g STOP C PLAY B REV h H G PQRS TUV WXYZ K L 1 2 Playing discs Note • To cancel random play, press STOP C button twice during random play.“Playmode OFF” appears on the screen. Random playback With this function, you can play a disc randomly instead of playing in the original order. 1 Press SETUP button to dis- play SETUP/CD menu. SETUP/CD menu will appear. Screen: 2 Select “CD” using { / B but- tons, then press ENTER but- ton. CD Playback Mode menu will appear. 3 Select “Random Play” using K / L buttons, then press ENTER button. Random play will start. CD Playback Mode Random Play Program Play Setup Menu MP3 MP3 CD CD SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN MENU/LIST TOP MENU F { B FWD g STOP C PLAY B REV h H G K L 2 3 1

Connections Getting started Changing the SETUP menu Others Español 53 Repeat/Random/Program playback (cont’d) Note • To erase tracks you selected, press CLEAR button. • You can make program set- tings up to 50. • To cancel program play, press STOP C button twice during program play.“Playmode OFF” appears on the screen. • You may also select a desired track using Number buttons at step 4. Program play You can program the disc to play in your desired order. 1 Press SETUP button to dis- play SETUP/CD menu. SETUP/CD menu will appear. Screen: 2 Select “CD” using { / B but- tons, then press ENTER but- ton. CD Playback Mode menu will appear. 3 Select “Program Play” using K / L buttons, then press ENTER button. Program play list will appear. 4 Select a desired track using K / L buttons, then press ENTER button or B button. A cursor will move to next. 5 Press PLAY B button to start program play. Program play will start. CD Playback Mode > Program Play Total 00:04:30 07 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - CD Playback Mode > Program Play Total 00:00:00 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - CD Playback Mode Random Play Program Play Setup Menu CD CD POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 5 2 3 4 1 Playing discs

Playing discs Note • Some discs will only allow you to change the sound- track from the disc’s menu. Press TOP MENU button or MENU / LIST button to dis- play the disc’s menu. • On DVD-RW discs recorded in VR mode that may have both a main and a sub audio channel, you can switch to main (L), sub audio (R) or a mix of both (L/R). • This unit CANNOT record in both stereo and SAP (Secondary Audio Program) at the same time. You can select the format of audio and video as you prefer depending on the contents of the disc you are playing. Switching audio soundtrack When playing a DVD-Video disc recorded with two or more soundtracks (these are often in different languages), you can switch them during play. On DVD-RW discs recorded in VR mode, you can switch to main (L), sub audio (R) or a mix of both (L/R). 1 During play, press DISPLAY button. The display menu will appear. Screen: 2 Select icon using { / B buttons, then press ENTER button. Audio menu will appear. 3 Select a desired audio sound- track using K / L buttons, then press ENTER button. Audio soundtrack will switch. 4 Select a desired audio chan- nel using K / L buttons, then press ENTER button. Audio channel will switch. 1 1 00:00:00 1 Dolby Digital Dual 2 Dolby Digital 2ch DVD-RW VR Original L/R L R 1 1 00:00:00 1 Dolby Digital Dual L/R 2 Dolby Digital 2ch ---- DVD-RW VR Original 1 1 00:00:00 1 Dolby Digital 5.1ch English 2 Dolby Digital 2ch Japanese DVD-Video 1 1 01:23:45 DVD-Video DVD-RW DVD-RW VR DVD-V DVD-V POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 3 1 4

Playing discs Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Note • Some discs will only allow you to change the subtitle from the disc menu. Press TOP MENU button or MENU / LIST button to display the disc menu. • If a 4-digit language code appears in the subtitle menu at step 2, please refer to the Language code on page 95. When playing Audio CDs or MP3 files you can switch between stereo, just the left channel or just the right channel. 1 During play, press DISPLAY button. The display menu will appear. Screen: 2 Select icon using { / B buttons, then press ENTER button. Audio menu will appear. 3 Select a desired audio chan- nel using K / L buttons, then press ENTER button. Audio channel will switch. 1 00:00:00 Audio CD L/R L R 1 00:00:00 Audio CD MP3 MP3 CD CD Switching subtitles Many DVD Video discs have subti- tles in one or more languages – the case usually tells you which subtitle languages are available. You can switch subtitle languages anytime during playback. 1 During play, press DISPLAY button. The display menu will appear. Screen: 2 Select icon using { / B buttons, then press ENTER button. Subtitle menu will appear. 3 Select a desired subtitle lan- guage using K / L buttons, then press ENTER button. Subtitle will be displayed in the selected language. When selecting “OFF,” subtitle will disappear. 1 1 00:00:00 OFF 1English 2Japanese DVD-Video 1 1 01:23:45 DVD-Video DVD-RW DVD-RW VR DVD-V DVD-V POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 3 1 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 3 1

Playing discs Switching camera angles Some DVD Video discs feature scenes shot from two or more angles, check the case for details: it should be marked with a angle icon if it contains multi-angle scenes. 1 During play, press DISPLAY button. The display menu will appear. Screen: Angle icon appears when a switch- ing camera angle is available. 2 Select icon using { / B buttons, then press ENTER button. Angle will switch each time you press ENTER button. 1 1 01:23:45 DVD-Video DVD-V DVD-V Reducing block noise 1 During play, press DISPLAY button. The display menu will appear. Screen: 2 Select icon using { / B buttons, then press ENTER button. Noise Reduction menu will appear. 3 Select a desired option using K / L buttons, then press ENTER button. Your setting will be activated. This function reduces noise in the playback picture.When playing back discs recorded in long time mode such as SLP or SEP mode, select "Type 1" or "Type 2". ("Type 2" is more effective.) When playing back discs with a few noises such as DVD-Video discs, select "OFF". 1 1 00:00:00 OFF Type 1 Type 2 DVD-Video 1 1 01:23:45 DVD-Video DVD+R DVD+R DVD+RW DVD+RW Video DVD-R DVD-R DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-V DVD-V POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 1 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 2 3 1

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Guide to a title list Title list allows you to check the titles recorded on the disc easily.You can choose a title to play from this screen and easily edit the titles as you prefer. 1. Titles recorded on the disc can be selected to edit by pressing ENTER button with the cursor on the title. 2. Protect icon, which appears when the title has been protected. 3. The selected title thumbnails from the title list. • The selected title will be pla • A sound is not output. yed back automat- ically. 4. The menus in here for editing titles as you pre- fer.The available menus depends on the disc type and the format type. 5. The details of the title, which can be changed to the title name you will edit. 6. Time status bar of the title. 7. The arrow icon, which means the title list includes a next or a previous page. Press B or { button by following direction of the icon. 8. Playback status of the current disc. Editing discs with Video mode You can edit discs with Video mode for the following items. Be sure that once you edit titles, they will not remain as original. • Deleting titles (Refer to page 59) • Putting names on titles (Refer to pages 60-61) • Setting or clearing chapter markers (Refer to page 62) Disc > Edit > Original 1 JAN/1 1:00AM CH12 XP 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF Disc > Edit > Original 1 1 3 2 5 4 JAN/1 2:00AM JAN/1 3:00AM 6 JAN/1 6:00AM JAN/1 5:00AM JAN/1 1:00AM JAN/1 4:00AM ON 2 1 3 4 6 5 7 8 Note • Once a disc is finalized, editing the disc or recording to the disc will not be available. (Except DVD-RW discs in VR mode.) • A playlist is not available with the DVD-R discs and DVD-RW discs in Video mode.

Editing Editing original titles The following items can be used to edit the original titles. • Deleting titles (Refer to page 63) • Deleting parts of titles (Refer to pages 64-65) • Putting names on titles (Refer to pages 65-66) • Setting or clearing chapter markers (Refer to pages 67-68) • Setting pictures for thumbnails (Refer to pages 68-69) • Setting titles to protect (Refer to page 70) • Releasing titles from protecting (Refer to page 71) Editing playlists You can create a playlist from original titles, so that you can edit as you prefer without losing original titles. The following items you can edit with a playlist. • Deleting titles (Refer to page 72) • Deleting parts of titles (Refer to pages 73-74) • Putting names on titles (Refer to pages 74-75) • Setting or clearing chapter markers (Refer to pages 76-77) • Setting pictures for thumbnails (Refer to pages 77-78) • Adding titles to a playlist (Refer to page 79) • Deleting a playlist (Refer to page 80) Editing discs with VR mode For discs with VR mode, you can edit from “Original” menu or “Playlist” menu, which is created from the original. Note • Original titles once edited will not remain as recorded originally.When you want to leave the original as it is, edit the playlist as you prefer.

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Deleting titles You can delete titles which you do not need anymore. Be advised that the titles once deleted cannot be brought back to the disc. When the last title in the title list in Video mode is deleted, the disc space to record will be increased. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Titlelist will appear. Screen: 3 Select a desired title using K / L / { / B buttons, then press ENTER button. Edit menu will appear. 4 Select “Title Delete” using K / L buttons, then press ENTER button. Option window will appear. 5 Select “Yes” using { / B but- tons, then press ENTER but- ton. Title will be deleted. 6 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit 1 Title Delete Edit Title Name Chapter Mark Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit 1 0:01:25 Title Delete Edit Title Name Chapter Mark Yes No JAN/ 1 1:00AM CH12 XP Disc > Edit 1 Title Delete Edit Title Name Chapter Mark 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc Edit Format Finalize DVD-RW DVD-RW Video POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 3 4 5 1 6

Editing You can put title names on the titles and change the names from this menu. The names you put on the titles will be displayed on a titlelist. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Titlelist will appear. Screen: 3 Select a desired title using K / L / { / B buttons, then press ENTER button. Edit menu will appear. 4 Select “Edit Title Name” using K / L buttons, then press ENTER button. A window for entering a title name will appear. 5 To enter a title name, follow the steps of “Guide to edit title name” on this page. character set area for entering title names When you finish entering a title name, press ENTER button. Disc > Edit > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit 1 Title Delete Edit Title Name Chapter Mark 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc Edit Format Finalize DVD-RW DVD-RW Video Putting names on titles Press ABC DEF GHI JKL MNO PQRS TUV WXYZ abc def ghi jkl mno pqrs tuv wxyz ! ” # $ % & ’ ( ) + , - . / : ; < = > ? @ [ ] ^ _ { | } 2 3 4 5 6 7 8 9 0 1 ABC abc Select @ ! ? 123 1 1 2 3 4 5 6 7 8 9 0 *1 Press button, character set will be changed to the " @!? " mode automatically. [Step1]: Select a desired character set using K/L buttons, then press ENTER button. [Step2]: Press Number buttons following by the list below. [ Guide to edit title name ] A B C a b c 1 2 3 @ ! ? • To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. • To go on to the next entering area for letters, press button. B • You can enter up to 30 letters. *1 *1 * POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 5 1 3 2 5 4 1

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 6 Select “Yes” using { / B but- tons, then press ENTER but- ton. The name you entered will be activated for the title. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit > Edit Title Name 1 A B C a b c 1 2 3 @ ! ? abc Yes No Writing to Disc POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 6 7

Editing Note • You cannot select a time for putting markers beyond a length of a title. • The length of chapters may be slightly longer or shorter than the one specified at the step 5. • A chapter marker may be delayed according to the recording content. Setting or clearing chapter markers You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can set chapter markers at a speci- fied time you selected for titles with more than 5 minutes. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER button. Titlelist will appear. Screen: 3 Select a desired title using K / L / { / B buttons, then press ENTER button. Edit menu will appear. 4 Select “Chapter Mark” using K / L buttons, then press ENTER button. Option window will appear. 5 Select a desired time using K / L buttons, then press ENTER button. Option window will appear. 6 Select “Yes” using { / B but- tons, then press ENTER but- ton. A chapter marker will be added. If you select “OFF” at step 5, all the chapter markers will be erased. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. 1 0:01:25 Title Delete Edit Title Name Chapter Mark OFF 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes Yes No Disc > Edit JAN/ 1 1:00AM CH12 XP 1 0:01:25 Title Delete Edit Title Name Chapter Mark OFF 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes Disc > Edit JAN/ 1 1:00AM CH12 XP Disc > Edit 1 Title Delete Edit Title Name Chapter Mark 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc Edit Format Finalize DVD-RW DVD-RW Video POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 7 3 4 2 5 6 1

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español When a title is deleted from an original list in VR mode, the disc space to record will be increased. Be advised that the titles once deleted cannot be brought back to the disc. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “Original” using { / B buttons, then press ENTER button. Original list will appear. . 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Original menu will appear. 5 Select “Title Delete” using K / L buttons, then press ENTER button. Option window will appear. 6 Select “Yes” using { / B but- tons, then press ENTER but- ton. Title will be deleted. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP ON Disc > Edit > Original 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF Yes No JAN/ 1 1:00AM CH12 XP ON Disc > Edit > Original Disc > Edit > Original 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF JAN/ 1 1:00AM CH12 XP 0:01:25 ON Disc > Edit > Original 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 7 3 4 2 5 6 1 Deleting titles Deleting titles

Editing Deleting parts of titles Before editing Edited Start point End point You can delete part of a title, the disc space to record will be increased. Be advised that the parts once deleted cannot be brought back to the disc. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER button. Original/PlayList menu will appear. Screen: 3 Select “Original” using { / B buttons, then press ENTER button. Original list will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Original menu will appear. 5 Select “Scene Delete” using K / L buttons, then press ENTER button. Option window will appear. 6 Use SKIP H / G, REV E, FWD D, PLAY B, and PAUSE F buttons to decide the start point, then press ENTER.Then use SKIP H / G, REV E, FWD D, PLAY B, and PAUSE F buttons again to move to the end point, and press ENTER. Press ENTER again to start the preview. A cursor will move to “Preview.” You can check the preview by pressing ENTER. The bar at the bottom of the screen indi- cates the total and the elapsed time of the title, and the area selected for deletion will be indicated in red during the preview. 1 0:00:55 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF Start End Preview Delete JAN/ 1 1:00AM CH12 XP Disc > Edit > Original Disc > Edit > Original 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF JAN/ 1 1:00AM CH12 XP 0:01:25 ON Disc > Edit > Original 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 3 4 2 5 6 1 6

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 7 Select “Delete” using K / L buttons, then press ENTER button. Option window will appear. 8 Select “Yes” using { / B but- tons, then press ENTER but- ton. Selected area will be deleted, and a chapter marker is created auto- matically where deletion is per- formed. If the thumbnail of the title is in the deleted area, the thumbnail will be set to the first picture of the title. Playback will start from the newly created chapter marker. 9 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF Start End Preview Delete Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit > Original 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF Start End Preview Delete Yes No JAN/ 1 1:00AM CH12 XP Disc > Edit > Original Putting names on titles You can put title names on the titles and change the names from this menu. The names you put on the titles will be displayed on a titlelist. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 9 8 7 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 1 Note • You cannot select “Scene Delete” when the number of chapter markers in the original or playlist is more than 900. Instructions continue on page 66

Editing 3 Select “Original” using { / B buttons, then press ENTER button. Original list will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Original menu will appear. 5 Select “Edit Title Name” using K / L buttons, then press ENTER button. A window for entering a title name will appear. 6 To enter a title name, follow the steps of “Guide to edit title name” on this page. character set area for entering title names When you finish entering a title name, press ENTER button. 7 Select “Yes” using { / B but- tons, then press ENTER but- ton. The name you entered will be activated for the title. 8 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit > Original > Edit Title Name 1 A B C a b c 1 2 3 @ ! ? abc Yes No Writing to Disc Disc > Edit > Original > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit > Original > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit > Original 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF JAN/ 1 1:00AM CH12 XP 0:01:25 ON Disc > Edit > Original 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Press ABC DEF GHI JKL MNO PQRS TUV WXYZ abc def ghi jkl mno pqrs tuv wxyz ! ” # $ % & ’ ( ) + , - . / : ; < = > ? @ [ ] ^ _ { | } 2 3 4 5 6 7 8 9 0 1 ABC abc Select @ ! ? 123 1 1 2 3 4 5 6 7 8 9 0 *1 Press button, character set will be changed to the " @!? " mode automatically. [Step1]: Select a desired character set using K/L buttons, then press ENTER button. [Step2]: Press Number buttons following by the list below. [ Guide to edit title name ] A B C a b c 1 2 3 @ ! ? • To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. • To go on to the next entering area for letters, press button. B • You can enter up to 30 letters. *1 *1 * POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 6 8 5 4 7 6 3

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Setting or clearing chapter markers You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can put a chapter marker anywhere you want. When the number of chapter markers in the original list comes to 999 in total, you cannot add any more chapter markers. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “Original” using { / B buttons, then press ENTER button. Original list will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Original menu will appear. 5 Select “Chapter Mark” using K / L buttons, then press ENTER button. Option window will appear. 6 Use SKIP H / G, REV E, FWD D,PLAY B,and PAUSE F buttons to decide the point at which you will create a new chapter marker. Or, use SKIP H / G to decide a chapter marker that you will delete. Select “Add” or “Delete” accordingly using K / L buttons, then press ENTER button. Option window will appear. : 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF Yes No JAN/ 1 1:00AM CH12 XP ON Add Delete Disc > Edit > Original Chapter 1/1 F Disc > Edit > Original 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF JAN/ 1 1:00AM CH12 XP ON Add Delete Chapter 1/1 Disc > Edit > Original 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF JAN/ 1 1:00AM CH12 XP 0:01:25 ON Disc > Edit > Original 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 5 6 Instructions continue on page 68 6

Editing : • You cannot delete the first chapter marker of each title. 7 Select “Yes” using { / B but- tons, then press ENTER button. When you select “Add” at step 6, a new chapter marker will be creat- ed at the point you have decided. When you select “Delete” at step 6, the chapter marker you have selected will be deleted. : The chapter marker which you selected will be deleted. : 8 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF JAN/ 1 1:00AM CH12 XP ON Yes No Writing to Disc Add Delete Disc > Edit > Original Chapter 2/2 This operation may take a while to be completed. 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF JAN/ 1 1:00AM CH12 XP ON Yes No Writing to Disc Add Delete Disc > Edit > Original Chapter 1/1 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF Yes No JAN/ 1 1:00AM CH12 XP ON Add Delete Disc > Edit > Original Chapter 2/2 F Note • If a selected picture for a thumbnail is deleted by delet- ing a part of a title, a default picture will be selected. You can set a picture to each title for a thumbnail. It helps you to remember the contents of the title you are playing.The begin- ning picture has been selected as the default. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Setting pictures for thumbnails POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 8 7 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 3 Select “Original” using { / B buttons, then press ENTER button. Original list will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Original menu will appear. 5 Select “Index Picture Set” using K / L buttons. Use SKIP H / G, REV E, FWD D, PLAY B, and PAUSE F but- tons to decide the picture you want to select as a thumbnail.Then press ENTER button. Option window will appear. 6 Select “Yes” using { / B but- tons, then press ENTER but- ton. A picture for thumbnail will be set. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit > Original 1 Yes No Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF ON Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit > Original 1 0:01:25 Yes No Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF ON JAN/ 1 1:00AM CH12 XP F Disc > Edit > Original 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF JAN/ 1 1:00AM CH12 XP 0:01:25 ON Disc > Edit > Original 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 7 3 4 5 6 5

Editing To prevent accidental editing, or erasing the titles, you can protect them from the original menu. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “Original” using { / B buttons, then press ENTER button. Original list will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Original menu will appear. 5 Select “Protect OFF ➔ON” using K / L buttons, then press ENTER button. Option window will appear. 6 Select “Yes” using { / B but- tons, then press ENTER button. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. To protect a whole disc (DVD-RW VR mode Only): Select “Disc Protect” from Disc menu, then select “Yes”. Refer to “Setting a disc to pro- tect” on page 40. This operation may take a while to be completed. Disc > Edit > Original 1 Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP ON Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF Disc > Edit > Original 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF Yes No JAN/ 1 1:00AM CH12 XP ON Disc > Edit > Original 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF JAN/ 1 1:00AM CH12 XP 0:01:25 ON Disc > Edit > Original 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Setting titles to protect POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 7 5 6 Note • The protected title will be marked with a key icon in the original list.

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español You are allowed to release the titles protecting feature once pro- tected. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “Original” using { / B buttons, then press ENTER button. Original list will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Original menu will appear. 5 Select “Protect ON ➔OFF” using K / L buttons, then press ENTER button. Option window will appear. 6 Select “Yes” using { / B but- tons, then press ENTER but- ton. The key icon will dissappear from the title in the original list. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc Edit > Original 2 Yes No Writing to Disc JAN/ 1 2:00AM CH12 XP OFF Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect ON Disc Edit > Original 2 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect ON Yes No JAN/ 1 2:00AM CH12 XP OFF B Disc Edit > Original 2 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect ON JAN/ 1 2:00AM CH12 XP 0:01:25 OFF Disc > Edit > Original 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Releasing titles from protecting POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 7 5 6

Editing In VR mode, even when a title is deleted from a Playlist, the original title will remain in an Original list. The disc space to record will not be increased. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “PlayList” using { / B buttons, then press ENTER button. Playlist will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Playlist menu will appear. 5 Select “Title Delete” using K / L buttons, then press ENTER button. Option window will appear. 6 Select “Yes” using { / B but- tons, then press ENTER button. Title will be deleted. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit > Playlist 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Yes No JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 1 3 2 5 4 Add New Title Delete Playlist JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Deleting titles POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 7 5 6

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español Deleting parts of titles You can delete a specific part of a title. Even when a title is deleted from the playlist, the original title will remain. The disc space to record will not be increased. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER button. Original/PlayList menu will appear. Screen: 3 Select “PlayList” using { / B buttons, then press ENTER button. Playlist will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Playlist menu will appear. 5 Select “Scene Delete” using K / L buttons, then press ENTER button. Option window will appear. 6 Use SKIP H / G, REV E, FWD D, PLAY B, and PAUSE F buttons to decide the start point, then press ENTER.Then use SKIP H / G, REV E, FWD D, PLAY B, and PAUSE F buttons again to move to the end point, and press ENTER. Press ENTER again to start the preview. A cursor will move to “Preview.” You can check the preview by pressing ENTER. The bar at the bottom of the screen indicates the total and the elapsed time of the title, and the area selected for deletion will be indicated in red during the preview. Disc > Edit > Playlist 1 0:00:55 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Start End Preview Delete JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 1 3 2 5 4 Add New Title Delete Playlist JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 5 6 Instructions continue on page 74 Before editing Edited Start point End point 6

Editing 7 Select “Delete” using K / L buttons, then press ENTER button. Option window will appear. 8 Select “Yes” using { / B but- tons, then press ENTER but- ton. Part of a title will be deleted. 9 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit > Playlist 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Start End Preview Delete Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Start End Preview Delete Yes No JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist You can put title names on the titles and change the names from this menu. The names you put on the titles will be displayed on a titlelist. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “PlayList” using { / B buttons, then press ENTER button. Playlist will appear. Disc > Edit > Playlist 1 1 3 2 5 4 Add New Title Delete Playlist JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Putting names on titles POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 9 7 8 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 Note • You cannot select “Scene Delete” when the number of chapter markers in the original or playlist is more than 900.

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Playlist menu will appear. 5 Select “Edit Title Name” using K / L buttons, then press ENTER button. A window for entering a title name will appear. 6 To enter a title name, follow the steps of “Guide to edit title name” on this page. character set area for entering title names When you finish entering a title name, press ENTER button. 7 Select “Yes” using { / B but- tons, then press ENTER but- ton. The name you entered will be activated for the title. 8 After writing to disc is com- pleted, press SETUP to exit DISC menu. This operation may take a while to be completed. 1 A B C a b c 1 2 3 @ ! ? abc Yes No Writing to Disc Disc > Edit > Playlist > Edit Title Name Disc > Edit > Playlist > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set 0:01:25 JAN/ 1 1:00AM CH12 XP Press ABC DEF GHI JKL MNO PQRS TUV WXYZ abc def ghi jkl mno pqrs tuv wxyz ! ” # $ % & ’ ( ) + , - . / : ; < = > ? @ [ ] ^ _ { | } 2 3 4 5 6 7 8 9 0 1 ABC abc Select @ ! ? 123 1 1 2 3 4 5 6 7 8 9 0 *1 Press button, character set will be changed to the " @!? " mode automatically. [Step1]: Select a desired character set using K/L buttons, then press ENTER button. [Step2]: Press Number buttons following by the list below. [ Guide to edit title name ] A B C a b c 1 2 3 @ ! ? • To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. • To go on to the next entering area for letters, press button. B • You can enter up to 30 letters. *1 *1 * POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 8 4 5 6 7

Editing You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can put a chapter marker anywhere you want. When the number of chapter markers in the playlist comes to 999 in total, you cannot add any more chapter markers. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “PlayList” using { / B buttons, then press ENTER button. Playlist will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Playlist menu will appear. 5 Select “Chapter Mark” using K / L buttons, then press ENTER button. Option window will appear. 6 Use SKIP H / G, REV E, FWD D,PLAY B,and PAUSE F buttons to decide the point at which you will create a new chapter marker. Or, use SKIP H / G to decide a chapter marker that you will delete. Select “Add” or “Delete” accordingly using K / L buttons, then press ENTER button. Option window will appear. : 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Add Delete Yes No JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist Chapter 1/1 F Disc > Edit > Playlist 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Add Delete JAN/ 1 1:00AM CH12 XP Chapter 1/1 Disc > Edit > Playlist 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 1 3 2 5 4 Add New Title Delete Playlist JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Setting or clearing chapter markers POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 5 6 6

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español : • You cannot delete the first chapter of each title. 7 Select “Yes” using { / B but- tons, then press ENTER button. A chapter marker will be added. When you select “Add” at step 6, a new chapter marker will be creat- ed at the point you have decided. When you select “Delete” at step 6, the chapter marker you have selected will be deleted. : The chapter marker which you selected will be deleted. : 8 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Add Delete Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist Chapter 2/2 This operation may take a while to be completed. 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Add Delete Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist Chapter 1/1 1 0:01:25 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Add Delete Yes No JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist Chapter 2/2 F Note • If a selected picture for a thumbnail is deleted by delet- ing a part of a title, a default picture will be selected. Setting pictures for thumbnails You can set a picture to each title for a thumbnail. It helps you to remember the contents of the title you are play- ing.The beginning picture has been selected as the default. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 8 7 REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR MENU/LIST TOP MENU SPACE 7 8 9 0 F { B FWD g STOP C PLAY B REV h H G PQRS TUV WXYZ K L 1 1 2 Instructions continue on page 78

Editing 3 Select “PlayList” using { / B buttons, then press ENTER button. Playlist will appear. 4 Select a desired title using K / L / { / B buttons, then press ENTER button. Playlist menu will appear. 5 Select “Index Picture Set” using K / L buttons. Use SKIP H / G, REV E, FWD D, PLAY B, and PAUSE F but- tons to decide the picture you want to select as a thumbnail.Then press ENTER button. Option window will appear. 6 Select “Yes” using { / B but- tons, then press ENTER but- ton. A picture for thumbnail will be set. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. 1 Yes No Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist Disc > Edit > Playlist 1 0:01:25 Yes No Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set JAN/ 1 1:00AM CH12 XP F Disc > Edit > Playlist 1 Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit > Playlist 1 1 3 2 5 4 Add New Title Delete Playlist JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 7 3 4 5 6 5

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español You can add or delete a title in the playlist as you prefer. You can add titles to a Playlist up to 99. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “PlayList” using { / B buttons, then press ENTER button. Playlist will appear. 4 Select “Add New Title” using K / L / { / B buttons, then press ENTER button. Original list will appear. 5 Select a desired title using K / L / { / B buttons, then press ENTER button. 6 After writing to disc is com- pleted, press SETUP button to exit DISC menu. To delete a title from Playlist, refer to “Deleting titles” on page 72. To delete a Playlist, refer to “Deleting a Playlist” on page 80. Disc > Edit > Playlist 6 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 5:00AM JAN/1 3:00AM JAN/12 8:00PM Disc > Edit > Playlist > Add New Title Writing to Disc 58% Disc > Edit > Playlist > Add New Title 1 1 3 2 JAN/12 5:00PM JAN/12 8:00PM JAN/10 10:30AM Disc > Edit > Playlist 1 1 3 2 5 4 Add New Title Delete Playlist JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Adding titles to a Playlist POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 6 5

Editing Note • Deleting a Playlist will not increase the available record- ing time. A Playlist can be deleted if no longer needed. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Original/PlayList menu will appear. Screen: 3 Select “PlayList” using { / B buttons, then press ENTER button. Playlist will appear. 4 Select “Delete Playlist” using K / L / { / B buttons, then press ENTER button. Option window will appear. 5 Select “Yes” using { / B but- tons, then press ENTER but- ton. A Playlist will be erased. The unit will be in stop mode after exiting the DISC menu automatically. 1 1 3 2 5 4 JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM JAN/1 1:00AM JAN/1 4:00AM Add New Title Delete Playlist Yes No Disc > Edit > Playlist Disc > Edit > Playlist 1 1 3 2 5 4 Add New Title Delete Playlist JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc > Edit Original Disc Edit Format Finalize Disc Protect OFF ON DVD-RW DVD-RW VR Deleting a Playlist POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 5

Editing Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español You can delete titles which you do not need, however the disc space to record will not be changed. Be aware to know that the titles once deleted cannot be brought back to the disc. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER but- ton. Titlelist will appear. Screen: 3 Select a desired title using K / L / { / B buttons, then press ENTER button. Edit menu will appear. You cannot select “Chapter Mark”. 4 Select “Title Delete” using K / L buttons, then press ENTER button. Option window will appear. 5 Select “Yes” using { / B but- tons, then press ENTER but- ton. Title will be deleted. 6 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit 1 Title Delete Edit Title Name Chapter Mark Yes No Writing to Disc JAN/ 1 1:00AM CH12 XP Disc > Edit 1 0:01:25 Title Delete Edit Title Name Chapter Mark Yes No JAN/ 1 1:00AM CH12 XP Disc > Edit 1 Title Delete Edit Title Name Chapter Mark 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc Edit Format Finalize DVD-R DVD-R Deleting titles POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 6 5

Editing You can put names on the titles and change the names from this menu. The names you put on the titles will be displayed on a titlelist. 1 Press SETUP button. Select “DISC” using { / B buttons, then press ENTER button. DISC menu will appear. 2 Select “Edit” using K / L but- tons, then press ENTER button. Titlelist will appear. Screen: 3 Select a desired title using K / L / { / B buttons, then press ENTER button. Edit menu will appear. You cannot select “Chapter Mark”. 4 Select “Edit Title Name” using K / L buttons, then press ENTER button. A window for entering a title name will appear. 5 To enter a title name, follow the steps of “Guide to edit title name” on this page. character set area for entering title names When you finish entering a title name, press ENTER button. 6 Select “Yes” using { / B but- tons, then press ENTER but- ton. 7 After writing to disc is com- pleted, press SETUP button to exit DISC menu. This operation may take a while to be completed. Disc > Edit > Edit Title Name 1 A B C a b c 1 2 3 @ ! ? abc Yes No Writing to Disc Disc > Edit > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit > Edit Title Name 1 0:01:25 A B C a b c 1 2 3 @ ! ? JAN/ 1 1:00AM CH12 XP Disc > Edit 1 Title Delete Edit Title Name Chapter Mark 0:01:25 JAN/ 1 1:00AM CH12 XP Disc > Edit 1 1 3 2 5 4 JAN/1 1:00AM JAN/1 4:00AM JAN/1 2:00AM JAN/1 3:00AM JAN/1 5:00AM Disc Edit Format Finalize DVD-R DVD-R Putting names on titles Press ABC DEF GHI JKL MNO PQRS TUV WXYZ abc def ghi jkl mno pqrs tuv wxyz ! ” # $ % & ’ ( ) + , - . / : ; < = > ? @ [ ] ^ _ { | } 2 3 4 5 6 7 8 9 0 1 ABC abc Select @ ! ? 123 1 1 2 3 4 5 6 7 8 9 0 *1 Press button, character set will be changed to the " @!? " mode automatically. [Step1]: Select a desired character set using K/L buttons, then press ENTER button. [Step2]: Press Number buttons following by the list below. [ Guide to edit title name ] A B C a b c 1 2 3 @ ! ? • To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. • To go on to the next entering area for letters, press button. B • You can enter up to 30 letters. *1 *1 * POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 1 2 3 4 7 5 6 5

Changing the SETUP menu Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 83 Note • If you change the setting in SETUP menu, the information of contents stays on even when the power is switched off. 1.Language setting Pages 84-85 Pages 86-87 Pages 88-89 Pages 90-91 2.Display setting 3.Audio setting 4.Parental setting SETUP menu Contents Items (highlight is the default) Disc Menu Language Audio Language Subtitle Language Set the language for disc menu. Set the language for audio. Set the language for subtitle. Set the background transparency of OSD screen. Set the OSD screen color. 1 (Green), 2 (Blue), 3 (Red) Set the language for OSD (On Screen Display). Set the brightness of front display. Set the time to work the screen saver on the screen. Set the type of sound signal which outputs from the digital audio output jack. Set whether DTS signal will be output or not. Set whether the sound recorded in 96kHz will be down sampled in 48kHz. Compressing the range of sound volume. Outputting the sound during play in fast forward. Set the parental level of your DVD discs. Set and change the password. OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver Digital Out Dynamic Range Control Fast Forward with Audio Parental Lock (Change password) English French Spanish Original English French 100% 35% 25% OFF English French OFF 5 minutes 10minutes English Français Español Auto Bright Dark 1 2 3 ON OFF PCM Auto 48kHz 96kHz Dolby Digital PCM Stream DTS ON OFF ON OFF ALL level 8 to 1 Enter the current four-digit password The following table is the contents which you can set and the default settings. Refer to the following table for useful operation.

1 Press SETUP button to display SETUP/DISC menu. SETUP/DISC menu will appear. 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Playback” using K / L / { / B buttons, then press ENTER button. Option window will appear. 4 Select a desired item using K / L buttons, then press ENTER button. Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup Playback Setting Setup Menu Note • Only the languages supported by the disc can be selected. • Audio Language setting may not be available to some discs. • You can change or switch off the subtitles on a DVD disc also from the disc menu if it is available. 84 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 Press STOP button if you are playing a disc. 3 4 5 4

Changing the SETUP menu Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 85 Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF English French Spanish Other Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Original English French Spanish Other Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF OFF English French Spanish Other Disc Menu Language (Default : English) Set the language for Disc Menu. • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. • When Original is selected, the audio language will be in the disc’s default language. • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. Audio Language (Default : Original) Set the Audio language. Subtitle Language (Default : OFF) Set the subtitle language. If “Other” is selected, press 4-digit code using number buttons. guage e age e Control i h A di English Original All OFF ON O English French Spanish Other Code Input - - - - • When you finish entering the code, press ENTER button. Refer to the lan- guage code table on page 95. 5 Press SETUP button to exit SETUP menu.

1 Press SETUP button to display SETUP/DISC menu. SETUP/DISC menu will appear. 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Display” using K / L / { / B buttons, then press ENTER button. Option window will appear. 4 Select a desired item using K / L buttons, then press ENTER button. Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 10 minutes Bright 1 English 35% Setup Playback Setting Setup Menu 86 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 Press STOP button if you are playing a disc. 3 4 5

Changing the SETUP menu Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 87 Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35% Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35% Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35% Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35%100% 85% 70% 50% 35% 25% 10% 0% Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35% 1 2 3 Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35% English Français Español OSD Background Transparency (Default : 35%) Set the background transparency of OSD screen. You can choose one among 0% through 100%. • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. OSD Background Color (Default : 1 Green) Set the OSD screen color. You can choose one among 1(Green), 2(Blue), and 3(Red). OSD Language (Default : English) Set the language for OSD. Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer 1 English Screen Saver 10 minutes Bright 35% Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer 1 English Screen Saver 10 minutes Bright 35% Auto Bright Dark • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. FL Dimmer (Default : Bright) Set the brightness of front display. You can choose one among “Auto”, ”Bright” and ”Dark”. When “Auto” is selected, the display dims after 15 seconds of no use. Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35% Setup > Display OSD Background Transparency OSD Background Color OSD Language FL Dimmer Screen Saver 1 English 10 minutes Bright 35% OFF 5 minutes 10 minutes 15 minutes 30 minutes • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. Screen Saver (Default : 10 minutes) Set the time to work the screen saver function on the screen. 5 Press SETUP button to exit SETUP menu.

1 Press SETUP button to display SETUP/DISC menu. SETUP/DISC menu will appear. 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Playback” using K / L / { / B buttons, then press ENTER button. Option window will appear. 4 Select a desired item using K / L buttons, then press ENTER button. 88 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 Press STOP button if you are playing a disc. 3 4 5 Choose the appropriate Audio settings for your equipment. It will only affect DVD discs during playback. Note • Dynamic Range Control func- tion is available only on the discs which are recorded in the Dolby Digital format. Setup Menu Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio OFF 4:3 Letter Box All English Original OFF ON Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio OFF 4:3 Letter Box All English Original OFF ON PCM Dolby Digital DTS Digital Out Set the digital audio output. • Select a setting using K / L buttons, then press ENTER button. Option window will appear. Proceed to steps A, B or C. Setup Playback Setting Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF

Changing the SETUP menu Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 89 Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF ON OFF Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF ON OFF • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. • Dynamic Range Control func- tion is effective only with analog audio connection. • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. Dynamic Range Control (Default : ON) Set to ON to compress the range between soft and loud sounds. Fast Forward with Audio (Default : OFF) Set to ON to output the sound during play in fast forward of x2. 5 Press SETUP button to exit SETUP menu. Settings for Dolby Digital (Default : Stream) age ontrol Audio English Original OFF OFF ON PCM Dolby Digital DTS PCM Stream • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. PCM : Convert the Dolby Digital into PCM(2 channel). When your amplifier/decoder is NOT com- patible with Dolby Digital, set to “PCM”. Stream : Outputs Dolby Digital signals When your amplifier/decoder is compatible with Dolby Digital, set to “Stream”. Settings for PCM (Default :Auto) ntrol udio Original OFF OFF ON PCM Dolby Digital DTS Auto 48kHz 96kHz • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. Auto : Select “Auto” usually. 48kHz : If your amplifier/decoder is NOT com- patible with 96kHz PCM, select “48kHz”. 96kHz sound will be output in 48kHz. 96kHz : If your amplifier/decoder is compatible with 96kHz PCM, select “96kHz”. 96kHz sound will be output. B A Note When playing disc with copy- right protection • If you select “Auto”, the sound will be down sampled at 48kHz. • If you select “96kHz”, no digital sound will be output. Select “Auto”, so that outputting 48kHz digital sound. Note When playing a DVD-RW disc recorded in VR mode • If the audio source on a disc is Dolby Digital format, set “Dolby Digital” to “PCM” so that you can switch to main (L), sub audio (R), or a mix of both (L/R) with your amplifier/decoder. Settings for DTS (Default : OFF) ntrol udio g Original OFF OFF ON PCM Dolby Digital DTS ON OFF • Select a setting using K / L buttons, then press ENTER button. Your setting will be activated. ON : Outputs DTS signals. When your amplifier/decoder is compatible with DTS, set to “ON”. OFF : No DTS, signal is output. When your amplifier/decoder is NOT compatible with DTS, set to “OFF”. C

Changing the SETUP menu 1 Press SETUP button to display SETUP/DISC menu. SETUP/DISC menu will appear. 2 Select “SETUP” using { / B buttons, then press ENTER button. SETUP menu will appear. 3 Select “Playback” using K / L / { / B buttons, then press ENTER button. Option window will appear. 4 Select “Parental Lock” using K / L buttons, then press ENTER button. Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup Playback Setting Setup Menu 90 POWER DISPLAY REC MODE CLEAR CM SKIP SKIP REC PAUSE SETUP REPEAT ZOOM ENTER RETURN REC MONITOR OPEN/CLOSE TIMER PROG. MENU/LIST TOP MENU SPACE 1 2 3 4 5 6 7 8 9 0 F A { B FWD g STOP C PLAY B REV h H G CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ K L 1 2 Press STOP button if you are playing a disc. 3 4 5 Some DVD-Video discs feature a Parental Lock level. Playback will stop if the ratings exceed the levels you set, it will require you to enter a password before the disc will playback.This fea- ture prevents your children from viewing inappropriate materi- al. 4 Note • Parental lock function may not be available to some discs. • With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function oper- ates in the way that you have set. • Record the password in case you forget it.

Changing the SETUP menu Recording Playing discs Editing Before you start Connections Getting started Changing the SETUP menu Others Español 91 Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF All 8 7 6 5 4 3 2 1 Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF All 8 7 6 5 4 3 2 1 Password - - - - Parental Lock (Default :All) Set the Parental Lock level. • Change the parental level using K / L buttons, then press ENTER button. Option window will appear Proceed to steps A or B. • Select “Yes” using s / B buttons, then enter a new password using Number buttons. Your setting will be activated. • Select “Yes” using s / B buttons, then enter a new password using Number buttons. Your setting will be activated. 5 Press SETUP button to exit SETUP menu. A password has been set already Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF All 8 7 6 5 4 3 2 1 Change Password? Yes No Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF All 8 7 6 5 4 3 2 1 Change Password? Yes No Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF All 8 7 6 5 4 3 2 1 Password - - - - Setup > Playback TV Aspect Parental Lock Disc Menu Language Audio Language Subtitle Language Digital Out Dynamic Range Control Fast Forward with Audio 4:3 Letter Box All English Original OFF ON OFF All 8 7 6 5 4 3 2 1 Password * * * * Change the password • If you select “No”, proceed to Step 5. Yes Yes Note • Press CLEAR button to erase numbers entered incorrectly. • When you forget the pass- word or you want to clear all settings in Parental lock, enter 4,7,3,7 using Number buttons in option window. Password will be cleared and parental levels will be set to All. • If you select “No”, proceed to Step 5. • Enter the current password using Number buttons. A B A password has not been set yet

you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. Symptom Remedy Power The power does not turn on. • Check that the AC power cord is connected securely. • (In case of power failure) Check the braker. Picture There is no picture. • Re-connect the connecting cord securely. • The connecting cords are damaged. • The Setup Display appears. Press RETURN button to turn off the display. • Check the connection to your TV (page 13). • Check if the INTERLACE/PROGRESSIVE mode is set correctly according to your TV (page 13). • Switch the input selector on your TV (such as to "LINE1") so that the signal from the DVD recorder appears on the TV screen. Picture noise appears. • The disc is dirty or flawed. • If the picture output signal from the DVD recorder passes through your VCR to get to your TV, or if you are connected to a combination TV/VIDEO player, the copy-protection signal applied to some DVD programs could affect picture quality. If you still experience this problem even when you connect the DVD recorder directly to your TV, try connecting the DVD recorder to your TV's S-VIDEO input. TV program pictures are distorted. • Adjust TV antenna. • Adjust the picture (see the TV's instruction manual). • Place the DVD recorder and TV farther apart. • Place the TV and any bunched antenna cables farther apart. TV program reception does not fill the screen. • Try to set the channels with "Auto Preset" in SETUP menu (page 18). • Select a channel of any TV program using the CH o / p buttons. The playback picture or TV program from the equipment connected through the DVD recorder is distorted. • If the playback picture output from a DVD player, VCR, or tuner goes through the DVD recorder before reaching your TV, the copy-protection signal applied to some programs could affect picture quality. Disconnect the playback equipment in question and connect it directly to your TV. Sound There is no sound. • The disc is dirty or flawed. • Re-connect all connections securely. • The connecting cord is damaged. • Check the connections to the amplifier input. • The input source setting on the amplifier is incorrect. • The recorder is in pause mode or in Slow-motion Play mode. • The recorder is in fast forward or fast reverse mode. • If the audio signal does not come through the DIGITAL OUT (COAXIAL) jack, check the Audio Setup settings (pages 88-89). TV channels cannot be changed. • Switch the input to TV. • Connect the antenna cable correctly (page 13). Playback picture is distorted • Keep the equipment which may cause electrical disturbances, such as a cellular phone, away. Sound is noisy. • The disc is dirty or flawed. Remote control The remote control does not function. • Batteries are weak. • There are obstacles between the remote control and the DVD recorder. • The remote is far from the DVD recorder. • There are no batteries in the remote. • Turn on the DVD recorder. • The remote control is not pointed at the remote sensor on the DVD recorder. • If above remedies do not solve the problem, please call the Service Center for help.

Connections Getting started Changing the SETUP menu Others Español Symptom Remedy Recording/Timer recording/Editing The channel cannot be changed from the channel you are recording. • Set the TV's input to "TV." The DVD recorder starts playing from the disc automatically. • The DVD VIDEO features an auto playback function. Recording does not start immediately after you press REC button. • An unused DVD-R or DVD-RW was inserted. It takes a while for the DVD recorder to automatically format a DVD-RW. Some functions such as Stop, Search, or Slow-motion Play cannot be performed. • Depending on the disc, you may not be able to do some of the operations above. See the instruction manual supplied with the disc. The language for the sound track cannot be changed. • Multilingual tracks are not recorded on the DVD VIDEO, DVD-R or DVD-RW being played. • The DVD VIDEO prohibits the changing of the language for the sound track. • Try changing the language using the DVD VIDEO's menu. The angles cannot be changed. • Multi-angles are not recorded on the DVD VIDEO being played. • You are trying to change the angles when icon does not appear on the TV screen (page 56). • The DVD VIDEO prohibits changing angles. • Try changing the angle using the DVD VIDEO's menu. Nothing was recorded even though you set the timer setting correctly. • There was a power failure during recording. • The DVD recorder's internal clock stopped due to a power failure that lasted for more than 30 seconds. Reset the clock (pages 21-23). • Disconnect the AC power cord from the AC outlet, and connect it again. • The program contains copy protection signals that restricts copying. • The timer setting overlapped with another setting that was set later or has priority. The subtitle language cannot be changed or turned off. • Multilingual subtitle are not recorded on the DVD VIDEO. • The DVD VIDEO prohibits changing of the subtitles. • Try changing the subtitle using the DVD VIDEO's menu. The disc does not start playback from the beginning. • Resume play was activated (page 46). Press STOP C button twice. • You have inserted a disc whose Title menu or DVD menu automatically appears on the TV screen when it is first insert. Playback The disc does not play. • No disc is inserted. • A blank disc is inserted. • The disc is upside down. Insert the disc with the labeled side facing up. • The disc is not correctly inserted. • The DVD recorder cannot play certain discs (such as a CD- ROM) (page 41). • The region code on the DVD VIDEO does not match the DVD recorder (page 41). • Moisture has condensed inside the DVD recorder. Remove the disc and leave the DVD recorder turned on for about two hours until the moisture evaporates (page 4). • If the disc was recorded on another recorder, the DVD recorder cannot play the disc if it was not finalized (page 39). Playback image freezes for a second. • During the playback of two layered disc, picture may freeze for a moment when the 1st layer switches to the 2nd layer. This is not a malfunction. Recording does not stop immediately after you press STOP C button. • It will take a few seconds for the DVD recorder to input disc data before recording can stop. Timer recording is not complete or did not start from the beginning. • The timer setting overlapped with another setting that was set later or has priority (page 36). • Disc space was not enough.

properly. • When static electricity, etc., causes the DVD recorder to operate abnormally, unplug the DVD recorder and then plug it in again. The disc tray does not open when you press OPEN/CLOSE A button. • It may take a few seconds for the disc tray to open after you have recorded or edited a disc. • This is because the DVD recorder is adding disc data to the disc. "Repairing" appears on the display. • If there is a power failure or unplugging during recording, finalizing, formatting or editing, a Repairing process will begin automatically just after turning the unit on again. It may take several minutes up to about four hours. Repairing Disc Error Recording Error Recording Error Region Error Parental Lock On Recording Error --- Please eject the disc. --- Playback feature may not be available on this Disc. --- Please eject the disc. --- Playback is not authorized in your region. --- Please eject the disc. --- The current selected parental level Prohibits playback. This program is not allowed to be recorded. Recording Error This program is not recordable in Video mode. This program is not allowed to be recorded on this disc. Unplayable disc is inserted in the DVD recorder. The disc is upside down. Insert the standardized disc which bear the marks on page 41. Insert the disc with the labeled side facing up. Recording Error This disc is protected and not recordable. Can not record on this disc. Cause Error message Solution Playback is not authorized in the region of the DVD-Video disc which you inserted in the DVD recorder. The current selected parental level in the SETUP Menu prohibits playback. The recording function encountered the copy prohibited program. You are trying to record the copy- once program onto the DVD-RW disc in Video mode. You are trying to record onto the disc which is unrecordable, or the disc status is unable to record. The disc is dirty. The disc is damaged. You are trying to record the copy- once program onto the DVD-RW disc which is not compatible with CPRM. You are trying to record on to the protected disc which is set in the Disc Setting Menu. Insert the DVD-Video disc with region codes 1 or ALL. Check the "Parental Lock" setting (pages 90-91). You cannot record copy prohibited programs. Set "DVD-RW Recording Format" to "VR mode" (page 28). Release the disc protect setting in the Disc Setting menu (page 40). Insert the recordable disc, and ensure the disc status satisfies the recording requirements (pages 26-27). Clean the disc with a cleaning cloth. Replace the disc. Insert the DVD-RW disc (ver.1.1 compatible with CPRM). Recording Error Disc is full. You are trying to record onto the disc which has no space for recording. Insert the recordable disc with enough recording space. (No area for new recording)

Connections Getting started Changing the SETUP menu Others Español Language Code Language Code Language Code Language Code (Afan) Oromo 6159 Abkhazian 4748 Afar 4747 Afrikaans 4752 Albanian 6563 Amharic 4759 Arabic 4764 Armenian 5471 Assamese 4765 Aymara 4771 Azerbaijani 4772 Bashkir 4847 Basque 5167 Bengali;Bangla 4860 Bhutani 5072 Bihari 4854 Bislama 4855 Breton 4864 Bulgarian 4853 Burmese 5971 Byelorussian 4851 Cambodian 5759 Catalan 4947 Chinese 7254 Corsican 4961 Croatian 5464 Czech 4965 Danish 5047 Dutch 6058 English 5160 Esperanto 5161 Estonian 5166 Faroese 5261 Fiji 5256 Finnish 5255 French 5264 Frisian 5271 Galician 5358 Georgian 5747 German 5051 Greek 5158 Greenlandic 5758 Guarani 5360 Gujarati 5367 Hausa 5447 Hebrew 5569 Hindi 5455 Hungarian 5467 Icelandic 5565 Indonesian 5560 Interlingua 5547 Interlingue 5551 Inupiak 5557 Irish 5347 Italian 5566 Japanese 5647 Javanese 5669 Kannada 5760 Kashmiri 5765 Kazakh 5757 Kinyarwanda 6469 Kirghiz 5771 Kirundi 6460 Korean 5761 Kurdish 5767 Laothian 5861 Latin 5847 Latvian; Lettish 5868 Sindhi 6550 Singhalese 6555 Siswat 6565 Slovak 6557 Slovenian 6558 Somali 6561 Spanish 5165 Sundanese 6567 Swahili 6569 Swedish 6568 Tagalog 6658 Tajik 6653 Tamil 6647 Tatar 6666 Telugu 6651 Thai 6654 Tibetan 4861 Tigrinya 6655 Tonga 6661 Tsonga 6665 Turkish 6664 Turkmen 6657 Twi 6669 Ukrainian 6757 Urdu 6764 Uzbek 6772 Vietnamese 6855 Volapuk 6861 Welsh 4971 Wolof 6961 Xhosa 7054 Yiddish 5655 Yoruba 7161 Zulu 7267 Lingala 5860 Lithuanian 5866 Macedonian 5957 Malagasy 5953 Malay 5965 Malayalam 5958 Maltese 5966 Maori 5955 Marathi 5964 Moldavian 5961 Mongolian 5960 Nauru 6047 Nepali 6051 Norwegian 6061 Occitan 6149 Oriya 6164 Panjabi 6247 Pashto; Pushto 6265 Persian 5247 Polish 6258 Portuguese 6266 Quechua 6367 Rhaeto-Romance 6459 Romanian 6461 Russian 6467 Samoan 6559 Sangho 6553 Sanskrit 6547 Scots Gaelic 5350 Serbian 6564 Serbo-Croatian 6554 Sesotho 6566 Setswana 6660 Shona 6560 Recording Error You cannot record more than 99 titles on one disc. Recording Error You cannot record more the 999 chapters on one disc. Recording Error You cannot record on this disc as Control Information is full. Recording Error You cannot record on the disc as Power Calibration Area is full. Recording Error This disc is already finalized. Cause Error message Solution You are trying to record onto the disc on which the number of recording titles comes up to the maximum (99). You are trying to record onto the VR mode DVD-RW disc on which the number of recording chapters comes up to the maximum (999). This disc has no space to write the Control Information when recording or deleting contents. When editing has been repeatedly performed, the control Information area may come up to be full even the recording area has enough space. When recordings are performed repeatedly onto an unstable disc, this area may come up to be full. Every time you insert a disc for recording, the disc's working area will be taken up. And if you repeat this frequently, it will be used up sooner and you may not be able to record full 99 titles. You are trying to record onto the disc already finalized. Delete unnecessary titles (pages 59, 63, 72). Delete unnecessary chapter markers (pages 67, 76). Delete unnecessary titles (pages 59, 63, 72). Insert a new disc. Release the finalizing for this disc (page 39). (The maximum is 99) (The maximum is 999) 95 Language code

represents sound. Compare this to digital audio which can be an electrical signal, but is an indirect representation of sound. See also Digital audio. Aspect ratio The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the screen is almost square); widescreen models are 16:9 (the screen is almost twice as wide as it is high). Chapter Just as a book is split up into sev- eral chapters, a title on a DVD disc is usually divided into chap- ters. See also Title. Component video output Each signal of luminance(Y) and component(PB/CB, PR/CR) is inde- pendent to output so that you can experience picture color as it is. Also, due to compatibility with progressive video (480p), you can experience higher-density picture than that in interlace (480i). CPRM (Content Protection for Recordable Media) CPRM is a copy protection sys- tem with scramble system regard- ing the recording of “copy-once” broadcast programs (e.g. some satellite broadcasts). Digital audio An indirect representation of sound by numbers. During record- ing, the sound is measured at dis- crete intervals (44, 100 times a second for CD audio) by an ana- log-to-digital converter, generating a stream of numbers. On playback, a digital-to-analog converter gen- erates an analog signal based on these numbers. See also Sampling frequency and Analog audio. Dolby Digital The system to compress digital sound developed by Dolby Laboratories. It offers you sound of stereo(2ch) or multi-channel audio (up to 5.1ch). DTS (Digital Theater System) DTS is a 5.1channel surround sound system, but it is different from Dolby Digital.The formats were developed by Digital Theater System, Inc. Finalize To make DVD discs, which have been recorded on, possible to play in DVD players.With this DVD recorder, it is possible to finalize DVD-R/DVD-RW discs. MP3 (MPEG Audio Layer 3) MP3 is a method of compressing files.You can copy MP3 files on CD-RW/R discs from the comput- er and play the files on this unit. PCM (Pulse Code Modulation) The most common system of encoding digital audio, found on CDs and DAT. Excellent quality, but requires a lot of data com- pared to formats such as Dolby Digital and MPEG audio. For com- patibility with digital audio recorders (CD, MD and DAT) and AV amplifiers with digital inputs, this unit can convert Dolby Digital and MPEG audio to PCM. See also Digital audio. Playlist From this list you can play con- tents of a disc as your desired order or in sequence.Also it is allowed to search a specific scene directly. Progressive Scan (480p) A type of display that does not split each frame into fields, and instead scans directly through all the scanlines of each frame in order. Progressive Scan provides less flickering and higher image resolution than traditional (480i) TV signals. Refer to page 13 for instructions on selective Progressive Scan mode. Regions code Regions associate discs and play- ers with particular areas of the world.This unit will only play discs that have compatible region codes.You can find the region code of your unit by looking on the rear panel. Some discs are compatible with more than one region (or all regions). Sampling frequency The rate which sound is measured by a specified interval to turn into digital audio data.The numbers of sampling in one second defines as sampling frequency.The higher the rate, the better the sound quality as possible as it is. SAP (Secondary Audio Program) Sub-audio channel which is deliv- ered separately from main-audio channel.This audio channel is used as an alternate in bilingual broad- casting. S-Video output It delivers independently each signal of color(C) and luminance(Y) to TV as video signals, so that higher-quali- ty picture will be gained. Title (DVD only) A collection of chapters on DVD disc. See also chapter. Track Audio CDs use tracks to divide up the content of a disc.The DVD equivalent is called a chapter. See also Chapter.

Connections Getting started Changing the SETUP menu Others Español System Power requirements Power consumption Weight Dimensions (width x height x depth) Operating temperature Operating humidity TV format DVD-Video, DVD-RW/R, CD-DA, CD-RW/R AC120 V, 60 Hz 23 W (standby: 4.0 W) 6.0 lbs ( 2.7 kg ) 17 1/8" x 2 5/8" x 11 3/4" (435 x 66 x 297 mm) 41Fº to 104Fº (5ºC to 40ºC) 5% to 85% (no condensation) NTSC General Receivable channels VHF UHF CATV 2-13ch 14-69ch C1-C125ch Recording Tuner Input/Output Recording format Recordable discs Video Recording format (DVD-RW only), Video format (DVD-RW, DVD-R) DVD-ReWritable, DVD-Recordable Audio recording format Sampling frequency Compression format Video recording format Sampling frequency Compression format 13.5MHz MPEG 48kHz Dolby Digital Video input Input level Jacks Video output Output level Jacks Component video output Output level Jacks S-Video input Y (Iuminance) - Input level C (color) - Input level Jacks Audio input During audio input Jacks Audio output During audio output Jacks S-Video output Y (Iuminance) - Output level C (color) - Output level Jacks VHF/UHF antenna input/output terminal Input 1 (rear), 2 (front) 1 Vp-p (75Ω) RCA jack Output 1 1 Vp-p (75Ω) RCA jack Y: 1.0 Vp-p (75Ω), PB/CB, PR/CR: 0.7 Vp-p (75Ω) RCA jacks Input 1 (rear), 2 (front) 1 Vp-p (75Ω) 286 mVp-p (75Ω) 4 pin mini DIN Input 1 (rear), 2 (front) L/R 2V rms (Input impedance: more than 22kΩ) RCA jacks Output 1,2 L/R 2V rms (Output impedance: less than 1kΩ) RCA jacks Digital audio output Output level Jacks 500 mVp-p (75Ω) RCA jack 1 Vp-p (75Ω) 286 mVp-p (75Ω) 4 pin mini DIN VHF/UHF set 75Ω Note: The specifications and design of this product are subject to change without notice. For the location of the nearest Sharp Authorized Service Center, or to obtain product literature, accessories, supplies or customer assistance, please call 1-800-BE-SHARP (1-800-237-4277) or visit SHARP’s website (http://www.sharpusa.com). Service Information (For the U.S.)

CHOQUE NO EXPONGA ESTE APARATO A LA HUMEDAD. Este dispositivo cumple con la Parte 15 de las reglas de la FCC (Comisión Federal de Comunicaciones). La operación se encuentra sujeta a las dos condiciones siguientes: (1) Este dispositivo no debería producir interferencias perjudiciales, y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluyendo las que puedan producir una operación indeseable. INFORMACION Este equipo se ha sometido a todo tipo de pruebas y cumple con las normas establecidas para dispositivo digital de Clase B, de conformidad con la Parte 15 de las reglas de la FCC (Comisión Federal de Comunicaciones). Estas reglas están diseñadas para asegurar una protección razonable contra interferencias perjudiciales en las instalaciones resi- denciales. Este equipo genera, utiliza y puede emitir energía de radiofrecuencia y, si no se instala y utiliza debidamente, es decir, conforme a las instrucciones, podrían producirse interferencias perjudiciales en las radiocomunicaciones. Sin embargo, no se garantiza que estas interferencias no se produzcan en una instalación determinada. Si este equipo oca- siona interferencias en la recepción de radio o televisión, lo cual puede comprobarse con sólo apagar y encender el equipo, intente corregir el problema mediante una o una combinación de las siguientes medidas: —Reoriente la antena receptora o cámbiela de lugar. —Aumente la separación entre el equipo y el receptor. —Enchufe el equipo a una toma de corriente situada en un circuito distinto del receptor. —Consulte a su distribuidor o a un técnico experto en radio/televisión. PRECAUCION: ESTA UNIDAD HA SIDO CLASIFICADA COMO PRODUCTO CLASS 1 LASER. EL USO DE MANDOS O AJUSTES O LA REALIZACION DE PROCEDIMIENTOS DISTINTOS DE LOS INDICA- DOS EN LA PRESENTE IMPLICA EL RIESGO DE EXPOSICION A UNA RADIACION PELIGROSA. COMO LOS RAYOS LASER UTILIZADOS EN ESTA UNIDAD PUEDEN RESULTAR PERJUDICIALES PARA SUS OJOS, NO INTENTE DESARMAR EL GABINETE. SOLICITE EL SERVICIO UNICAMENTE A PERSONAL CUALIFI- CADO. “ADVERTENCIA—Las reglas de la FCC (Comisión Federal de Comunicaciones) estipulan que cualquier modificación o cambio a este equipo no aprobado expre- samente por el fabricante podrá anular la autorización del usuario para operar este equipo”. Este símbolo previene al usuario del voltaje ais- lado dentro de la unidad que puede provocar descargas eléctricas peligrosas. Este símbolo advierte al usuario que existen instrucciones de operación y de mantenimien- to en la literatura incluida en esta unidad. PRECAUCION: TPARA REDUCIR EL RIESGO DE DESCARGA ELECTRICA, NO QUITE LA CUBIERTA. EL USUARIO NO DEBERA DAR NINGUN TIPO DE SERVICIO A NINGUNA PARTE INTER- NA. DEBERA SER REALIZADO SOLO POR PERSONAL DE SERVICIO CALIFICADO. PRECAUCION PELIGRO DE DESCARGA ELECTRICA NO ABRIR DECLARACIÓN DE CONFORMIDAD Para futura referencia, anote los números de modelo y de serie (indica- dos en la parte posterior esta unidad) en el espacio provisto. No. de modelo: DV-SR45U No. de serie: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Este aparato digital de la Clase B cumple con la norma ICES-003 de Canadá. PRECAUCIÓN: PARA EVITAR DESCARGAS ELÉCTRICAS, HAGA QUE LA PALETA ANCHA DEL ENCHUFE COINCIDA CON LA RANURA ANCHA E INTRODÚZCALA HASTA EL FONDO.

Connections Getting started Changing the SETUP menu Others Español Importantes Medidas de Seguridad y Precauciones 1) Lea las instrucciones - Lea detenidamente todas las instruc- ciones de seguridad y operación antes de usar el producto. 2) Conserve las instrucciones - Conserve las instrucciones de seguridad y operación para consultas futuras. 3) Respete las advertencias - Observe estrictamente todas las advertencias impresas en el producto y las incluidas en el manual de instrucciones. 4) Siga las instrucciones - Siga todas las instrucciones de operación. 5) Limpieza - Desconecte el producto del tomacorriente mural antes de limpiarlo. No use limpiadores líquidos ni aerosol. Use un paño húmedo para la limpieza del producto. 6) Enchufes - No use enchfes no recomendados por el fabri- cante del producto, ya que podría ser peligroso. 7) Agua y humedad - No use este producto cerca del agua, por ejem- plo, cerca de una bañera o lavamanos, cerca del fregadero de la cocina o lavandería, en un piso mojado, cerca de una piscina, etc. 8) Accesorios - No instale este producto en un carro,soporte, trípode o mesa inestables. El grabador de videocassettes podría caerse, causando serias lesiones a un niño o adulto, resultando también severamente dañado. Uselo sólo el un carro, soporte, trípode o mesa recomendados por el fabricante, o vendidos con el producto.Toda instalación del producto deberán hacerse de acuerdo a las instruc- ciones del fabricante, empleando los accesorios de instalación recomendados por el mismo. 9) La combinación de producto y carro debe ser movida con cuidado. Las detenciones brus- cas, la fuerza excesiva y las superficies disparejas podrán hacer que el producto y el carro se vuelquen. 10) Ventilación - El gabinete del producto tiene renuras y aberturas de ventilación que garantizan el funcionamiento confiable del producto, evitando que se recaliente. Estas aberturas no deberán ser bloquear las aberturas, nunca setúe el grabador de videocassettes encima de una cama, sofá, alfombra u otra superficie similar. El grabador de videocassettes no debe ser instalado en un mueble emportado, como una repisa para libros o bastidor, a menos que se pueda garantizar una venti- lación adecuada,o cuando las instrucciones del fabricante así lo especifiquen. 11) Alimentación - Este grabador de videocassettes sólo debe ser operado mediante el tipo de fuente de alimentación especificado en la etiqueta indicadora. Si no seta seturo del tipo de fuente de alimentación que tiene en su casa, con- sulte a su distribuidor o a la compañía de electricidad local En el caso de grabador de doseñados para funcionar a pilas o con otras fuentes de alimentación, consulte el manuel de instrucciones respectivo. 12) Conexión a tierra o polarización - Este producto está equipa- do con una clavija polarizada de corriente alterna (una clavija que tiene una espiga más ancha que la otra). Esta clavija sola- mente pordá ser insertada en el tomacorriente en una sola dirección. Esta es una medida de seguridad. Si no puediera insertar completamente la clavija en el tomacorriente, vuelva a intentarlo invirtiendo la clavija. Si aún no fuera posible insertar la clavija, tome contacto con un electricista para que repare su tomacorriente obsoleto . No modifique las características de seguridad de la clavija polarizada. 13) Protección del cable de alimentación - Los cables de ali- mentación deberán ser tendidos de manera tal que la proba- bilidad de que sean pisados o aplastados por otros objetos sea mínima.Preste especial atención a las clavijas de los cables,a los receptáculos, y al punto por donde salen del producto. 14) Conexión Tierra de una Antena Exterior: Si una antena exterior o sistema de cable es conectado al aparato de vídeo, asegúrese de que la antena o el cableado tenga conexión tierra para conseguir de esta manera una protección contra voltajes no deseados y car- gas estáticas. El artículo 810 del Código de Electricidad Nacional ANSI/NFPA número 70, proporciona información acerca de la manera adecuada de conexiones a tierra de la estructura del mástil y la estructura soporte, sobre la unidad del cable del interi- S3125A ADVERTENCIA SOBRE EL USO DE CARROS PORTÁTILES or de cobre de antena, tamaño de los conductores tierra, ubi- cación de la unidad de descarga de la antena, conexión a los elec- trodos tierra, y requerimientos de los electrodos tierra (Fig.A). 15) Tormentas eléctricas - Como medida adicional de protec- ción durante tormentas eléctricas, o cuando el producto permanezca sin uso durante períodos prolongados de tiem- po, desconéctelo del tomoacorriente mural y desconecte la antena o sistema de cable. Esto evitará que el grabador de videocassettes resulte dañado por tormentas eléctricas o sobretensiones en la línea de alimentación. 16) Líneas de alimentación - Un antena exterior no debe ser instalada en la cercanía de líneas de alimentación aéreas ni de otros circuitos de potencial para iluminación eléctrica, o donde pueda caerse y hacer contacto con tales líneas o cir- cuitos.Al instalar un sistema de antena exterior, enta mucho cuidado de no tocar tales líneas o circuitos de alimentación, ya que el contacto con ellos podría será fatal. 17) Sobrecarga - No sobrecargue los tomacorrientes murales ni los cables de extensión, ya que esto podría causar incen- dios o descargas eléctricas. 18) Entrada de objetos y líquidos - Nunca introduzca objetos de ningún tipo por las aberturas de sete producto, ya que por- dría tocar peligrosos puntos de alta tensión o cortocircuitar partes, provocando incendios o descargas elécticas. Nunca derrame ningún tipo de líquido sobre el producto. 19) Servicio - No intente reparar el producto usted mismo;al abrir o desmontar las cobiertas usted se expondrá a alta tensión y a otros peligros. Solicite todo servicio a personal calificado. 20) Daños que requieran reparación - En los siguientes casos, desconecte el producto del tomacorriente mural y llame a un técnico de servicio calificado: a) Cuando el cable de alimentación o la clavija estén dañados, b) Si se ha derramado líquido sobre la unidad, o si algún objeto ha caído dentro del producto, c) Si el producto ha sido expuesto a la lluvia o al agua, d) Cuando a pesar de haber sebuido las instrucciones de operación, el producto no funcione normalmente.Ajuste solamente los controles mencionados en el manual de instrucciones; el ajuste incorrecto de otros controles podrá causar daños a la unidad, la que por lo general requerirá de un prolongado trabajo de reparación (por un técnico calificado) para que sus condiciones normales de operación puedan ser restablecidas, e) Si el producto se ha caído o si el gabinete se ha dañado. f) Cuando el producto muestre un cambio notorio en su rendimiento. 21) Piezas de requesto - Cuando sea necesario reemplazar piezas, asegúrese de que el técnico de servicio emplee las piezas de requesto especificadas por el fabricante, o piezas que tengan las mismas características que las piezas origi- nales. Las sustituciones no autorizadas podrán causar incen- dios, descargas eléctricas y otoros problemas. 22) Revisión de seguridad - Al finalizar cualquier servicio de mantenimiento o reparación de este producto, solicítele al técnico que efectúe comprobaciones de seguridad para determinar si el producto se encuentra o no en condiciones óptimas de operación. 23) Calor - Este producto debe colocarse fuera del alcance de fuentes de calor tales como radiadores, rejillas de calefac- ción, estufas o cualquier otro producto destinado a pro- ducir calor, incluyendo los amplificadores. FIGURA A EJEMPLO DE CONEXIÓN A TIERRA DE ANTENA DE ACUERDO CON EL CÓDIGO ELÉCTRICO NACIONAL. CABLE DE COBRE PARA LA ANTENA. UNIDAD PARA LA DESCARGA DE LA ANTENA (NEC SECCIÓN 810-20) CONDUCTORES TIERRA (NEC SECCIÓN 810-21) ABRAZADERA DE LA ANTENA. ABRAZADERA A TIERRA. EQUIPO PARA EL SERVICIO ELÉCTRICO SISTEMA DE ELECTRODOS PARA EL SUMINISTRO DE TOMA A TIERRA (NEC ARTÍCULO 250, PARTE H) CÓDIGO DE NEC NATIONAL ELECTRIC S2898A

Español 100 Estas instrucciones le ayudarán a entender fácilmente cómo grabar discos DVD. Nota: Asegúrese que las pilas están en el mando a distancia y que ha conectado correctamente esta unidad y el TV. Paso 1: Elija un tipo de disco Puede elegir entre distintos tipos de discos DVD grabables. Elija un tipo de disco DVD grabable de acuerdo con sus necesidades de reproducción/ grabación.Vea los "tipos de discos DVD" en la parte inferior de esta página para más detalles sobre las diferencias entre los distintos medios compatibles. Este grabador de DVD puede grabar los sigu- ientes tipos de discos. * Esta unidad no puede grabar en los discos siguientes. • DVD-RW Ver 1.2 / 2-4x compatible con CPRM • DVD-R General Ver 2.0 / 8x Por ejemplo, cuando desea grabar repetidamente en el mismo disco o cuando desea editar el disco después de grabar, seleccione el disco de tipo regrabable DVD-RW. Cuando desea guardar grabaciones sin alterarlos, un DVD no regrabable DVD-R puede ser más conveniente. 4.7 Paso 2:Coloque un disco en blanco POWER DISPLAY OPEN/CLOSE TIMER PROG. 1 2 3 A CH .@/: ABC DEF GHI JKL MNO POWER DISPLAY OPEN/CLOSE TIMER PROG. 1 2 3 A CH .@/: ABC DEF GHI JKL MNO Mando a distancia Para abrir Para cerrar Formato del disco Coloque el disco en el grabador. Haga el formato del disco del menú SETUP, exis- ten los formatos de video (modo de Video) o de grabación de video (modo VR) según el tipo de disco colocado. Esto es necesario para preparar el disco para grabación.Vea los detalles en las páginas 28-30. * Al formatear, todo el con- tenido de ese disco se bor- rarán. • La unidad empieza a for- matear automáticamente cuando se inserta un disco no usado. Tipos de disco DVD . DVD-RW VR DVD-RW Video Desea Grabar programas de TV Volver a utilizar borrando partes no deseadas Editar las grabaciones Editar/grabar de equipos conectados Copiar discos para distribución Reproducir en otro equipo de DVD *1 *1 DVD-RW VR DVD-RW Video Detalles Grabación ¿Regrabable? Sí Sí Puede crear capítulos a intervalos fijos (auto.) Sí Sí Puede crear capítulos donde desee (manual) Sí No Puede grabar imágenes de tamaño 16:9 Sí Sí Puede grabar un programa de Copia-una-vez Sí No Edición Puede hacer funciones de edición básica Sí Sí Puede hacer funciones de edición avanzadas (edición de lista a reproducir) Sí No No Sí No Sí No Sí No *1 El DVD-RW (modo VR) sólo puede reproducirse en equipos de DV compatibles con VR. Nota: Para más detalles sobre las funciones anteriores y las limitaciones implícitas, lea las explicaciones en este manual. DVD-R DVD-R : Más adecuado : Puede utilizar : Algunas funciones son limitadas : No puede utilizar 2 Para encender 1 3 Cargando Esta operación puede demorar en reconocerse.