Renesas M16C/30P Operation & User’s Manual

2. Setup REJ10J0868-0200 Rev.2.00 January 16, 2006 2. Replace the oscillator circuit board (see Figure 2.22). Oscillator circuit board The Figure on the left shows the oscillator circuit board. Unscrew the screw securing the oscillator circuit board. Lift off the oscillator circuit board. Attach another oscillator circuit board to the connector. Secure the new oscillator circuit board with the screw. Figure 2.22 Replacing the oscillator circuit board 3. Reinstall the upper cover and secure the four screws of the PC7501. CAUTION Note on Replacing the Oscillator C ...

2. Setup REJ10J0868-0200 Rev.2.00 January 16, 2006 2.9.4 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2) Here following is a procedure of connecting to a 100-pin 0.65-mm-pitch foot pattern on the user system using the M3T- DIRECT100S (not included). For details on the M3T-100LCC-DMS (not included) and M3T-DIRECT100S (not included), refer to each user's manual. (1) Attach the M3T-DIRECT100S to the user system. (2) Attach the M3T-100LCC-DMS to the M3T-DIRECT100S. (3) Attach the CN2 side of the M30800T-PTC to the J4 side of the M3062PT2-EPB. (4) Attach t ...

2. Setup REJ10J0868-0200 Rev.2.00 January 16, 2006 2.8.2 If an Error is Detected in the Self-check If the self-check does not result normally (ERROR 1 to ERROR 4 in Figure 2.6), check the following. (1) Recheck the connection of the emulation probe and PC7501. (2) Redownload the proper firmware. IMPORTANT Note on the Self-check: z Perform the self-check while not connecting the user system. z If the self-check does not result normally (excluding user system errors), the emulation probe may be damaged. Then contact your local distributor. Page 29 of 102 ...

3. Usage (How to Use the Emulator Debugger) REJ10J0868-0200 Rev.2.00 January 16, 2006 (2) Debugging Information tab Specifying the compiler used and the object format Specify the compiler you are using and the format of the object file output by the compiler. - Compiler Select the compiler you are using. (By default, the C compiler from Renesas is selected.) - Object Format Select the format of the object file that is output by the compiler you are using. Specifying the method for storing debug information There are two methods for storing debug information: on-m ...

4. Hardware Specifications REJ10J0868-0200 Rev.2.00 January 16, 2006 Figure 4.5 Memory expansion mode and microprocessor mode (2 wait, accessing external area and using multiplex bus) Read timing Write timing BCLK CSi ADi BHE ALE RD ADi /DBi td(BCLK-CS) th(BCLK-CS) tcyc td(BCLK-AD) th(BCLK-AD) th(RD-CS) td(BCLK-ALE) th(BCLK-ALE) th(RD-AD) td(BCLK-RD) th(BCLK-RD) tac3(RD-DB) Hi-Z tsu(DB-RD) th(RD-DB) BCLK CSi ADi BHE ALE WR, WRL,WRH ADi /DBi td(BCLK-CS) th(BCLK-CS) tcyc td(BCLK-AD) td(BCLK-ALE) th(BCLK-ALE) th(WR-AD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) td(DB-WR) t ...

Precautions for safety REJ10J0868-0200 Rev.2.00 January 16, 2006 Precautions for Safety Definitions of Signal Words In both the user’s manual and on the product itself, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product. This symbol represents a warning about safety. It is used to arouse caution about ...

3. Usage (How to Use the Emulator Debugger) REJ10J0868-0200 Rev.2.00 January 16, 2006 (2) MAP tab Specifying the emulation memory allocation Sets the memory area assigned to the emulation memory by 4KB. Up to four areas can be set. An area set to [INTERNAL] will be allocated to the emulation memory by selecting the check box. An unchecked area or an unset area will be allocated to external area. The setting is effective only in the CS3#, CS2#, CS1# and CS0#. The maps of SFR, internal ROM and RAM are set automatically. (3) Flash Clear tab Setting to clear the MCU� ...

3. Usage (How to Use the Emulator Debugger) REJ10J0868-0200 Rev.2.00 January 16, 2006 2. Option Setting the debug options Check the box when not downloading the program to the internal flash ROM of the MCU. If this box is checked, the working efficiency (downloading, software break, etc.) will be improved because the program is downloaded in the emulation memory in the PC7501. However, maximum operating frequency is 10MHz The box is unchecked by default. 3. MCU Status Referring to the MCU Status It shows the status of each MCU pin. Check it to see if the MCU stat ...