Sharp XG-MB70X Setup Manual

Connecting Pin Assignments............................. 3 RS-232C Specifications and Commands .......... 4 Setting up the Projector Network Environment ... 6 1. Connecting the Projector to a Computer ........... 7 2. Setting an IP Address for the Computer ............ 8 3. Setting up a Network Connection for the Projector .. 10 Controlling the Projecter via LAN.................... 12 Controlling the Projector Using Internet Explorer (Version 5.0 or later)................................... 12 Confirming the Projector Status (Status) ............. 13 Controlling the Projector (Control) ....................... 13 Setting and Adjusting the Projector (Setting & Adjustment) ............................... 14 Setting the Security (Network – Security) ............ 14 Making General Settings for the Network (Network – General) .................................. 15 Setting for Sending E-mail when an Error Occurs (Mail – Originator) ..................................... 15 Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail – Recipient Setting) ..... 16 Setting the Projector Using RS-232C or Telnet ......17 When Connecting Using RS-232C....................... 17 When Connecting Using Telnet ............................ 18 SETUP MENU (Main Menu) ................................. 19 ADVANCED SETUP MENU ................................. 19 Controlling the Projector Using RS-232C or Telnet ......20 View Setting Detail List ([V]View All Setting) ....... 20 Set Items ............................................................... 20 Save Settings and Quit ([S]Save & Quit) ............. 21 Quit without Saving Settings ([Q]Quit Unchanged) .. 21 IP Address Setting ([1]IP Address) ....................... 22 Subnet Mask Setting ([2]Subnet Mask) ............... 22 Default Gateway Setting ([3]Default Gateway) .... 22 User Name Setting ([4]User Name) ..................... 23 Password Setting ([5]Password) .......................... 23 RS-232C Baud Rate Setting ([6]RS-232C Baud Rate) ............................ 23 Projector Name Setting ([7]Projector Name) ....... 23 Disconnecting All Connections ([D]Disconnect All) ...................................... 24 Entering ADVANCED SETUP MENU ([A]Advanced Setup) .................................. 24 Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) ............. 24 Data Port Setting (ADVANCED[2]Data Port) ....... 24 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) ............ 25 Setting of Accept IP Address (ADVANCED[6]Accept IP Addr(1) – [8]Accept IP Addr(3)) ................. 25 Accepting All IP Addresses (ADVANCED[9]Accept All IP Addr) ............ 25 Setting of Search Port (ADVANCED[0]Search Port) ...................... 26 Return to Default Settings (ADVANCED[!]Restore Default Setting) ............ 26 Return to Main Menu (ADVANCED[Q]Return to Main Menu) .............. 26 Troubleshooting ................................................. 27 Dimensions ........................................................ 30

Projection distance [L] Diag. [χ] Width Height Minimum [L1] Maximum [L2] 250" (635 cm) 553 cm (218") 311 cm (123") 8.2 m (27' 0") 12.4 m (40' 8") –61.1 cm (–24 5/64") 225" (572 cm) 498 cm (196") 280 cm (110") 7.4 m (24' 3") 11.2 m (36' 7") –55.0 cm (–21 43/64") 200" (508 cm) 443 cm (174") 249 cm (98") 6.6 m (21' 7") 9.9 m (32' 6") –48.9 cm (–19 17/64") 150" (381 cm) 332 cm (131") 187 cm (74") 4.9 m (16' 2") 7.4 m (24' 5") –36.7 cm (–14 14/32") 133" (338 cm) 294 cm (116") 166 cm (65") 4.4 m (14' 4") 6.6 m (21' 8") –32.5 cm (–12 13/16") 106" (269 cm) 235 cm (92") 132 cm (52") 3.5 m (11' 5") 5.3 m (17' 3") –25.9 cm (–10 13/64") 100" (254 cm) 221 cm (87") 125 cm (49") 3.3 m (10'10") 5.0 m (16' 3") –24.5 cm (–9 5/8") 92" (234 cm) 204 cm (80") 115 cm (45") 3.0 m (9'11") 4.6 m (15' 0") –22.5 cm (–8 55/64") 84" (213 cm) 186 cm (73") 105 cm (41") 2.8 m (9' 1") 4.2 m (13' 8") –20.5 cm (–8 3/32") 72" (183 cm) 159 cm (63") 90 cm (35") 2.4 m (7' 9") 3.6 m (11' 9") –17.6 cm (–6 15/16") 60" (152 cm) 133 cm (52") 75 cm (29") 2.0 m (6' 6") 3.0 m (9' 9") –14.7 cm (–5 25/32") 40" (102 cm) 89 cm (35") 50 cm (20") 1.3 m (4' 4") 2.0 m (6' 6") –9.8 cm (–3 55/64") Picture (Screen) size Projection distance [L] Diag. [χ] Width Height Minimum [L1] Maximum [L2] 300" (762 cm) 610 cm (240”) 457 cm (180") 9.1 m (29' 9") 13.7 m (44' 9") –10.2 cm (–4 1/64") 250" (635 cm) 508 cm (200") 381 cm (150") 7.6 m (24' 9") 11.4 m (37' 4") –8.5 cm (–3 11/32") 200" (508 cm) 406 cm (160") 305 cm (120") 6.0 m (19'10") 9.1 m (29'10") –6.8 cm (–2 43/64") 150" (381 cm) 305 cm (120") 229 cm (90") 4.5 m (14'10") 6.8 m (22' 5") –5.1 cm (–2 1/64") 100" (254 cm) 203 cm (80") 152 cm (60") 3.0 m (9'11") 4.6 m (14'11") –3.4 cm (–1 11/32") 84" (213 cm) 171 cm (67") 128 cm (50") 2.5 m (8' 4") 3.8 m (12' 6") –2.9 cm (–1 1/8") 72" (183 cm) 146 cm (58") 110 cm (43") 2.2 m (7' 2") 3.3 m (10' 9") –2.4 cm (–31/32") 60" (152 cm) 122 cm (48") 91 cm (36") 1.8 m (5'11") 2.7 m (8'11") –2.0 cm (–51/64") 40" (102 cm) 81 cm (32") 61 cm (24") 1.2 m (4' 0") 1.8 m (6' 0") –1.4 cm (–17/32") Distance from the bottom of the image to the lens center [H] The formula for picture size and projection distance [m/cm] [Feet/inches] L1 (m) = 0.0302χ L1 (ft) = 0.0302χ / 0.3048 L2 (m) = 0.0455χ L2 (ft) = 0.0455χ / 0.3048 H (cm) = –0.034χ H (in) = –0.034χ / 2.54 χ: Picture size (diag.) (in/cm) L: Projection distance(m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the bottom of the image to the lens center (cm/in) Note • There may be an error of ± 3% in the above values. • Values with a minus (–) sign indicate that the lens center is lower than the bottom of the screen. The formula for picture size and projection distance [m/cm] [Feet/inches] L1 (m) = 0.0329χ L1 (ft) = 0.0329χ / 0.3048 L2 (m) = 0.04957χ L2 (ft) = 0.04957χ / 0.3048 H (cm) = –0.24459χ H (in) = –0.24459χ / 2.54 χ: Picture size (diag.) (in/cm) L: Projection distance(m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the bottom of the image to the lens center (cm/in) STRETCH Mode (16:9) Distance from the bottom of the image to the lens center [H] Screen Size and Projection Distance H L Side View Screen Lens center The projection screen size varies according to the distance from the lens of the projector to the screen. Install the projector so that projected images are projected onto the screen at the optimum size by referring to the table below. Use the values in the table as a reference when installing the projector. NORMAL Mode (4:3)

Pin No. Signal Name I/O Reference 1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Not connected 5 SG Signal Ground Connected to internal circuit 6 Not connected 7 RS Connected to Pin 8 8 CS Connected to Pin 7 9 Not connected DIN-D-sub RS-232C adaptor: 9-pin D-sub male connector Pin No. Signal Name I/O Reference 1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Not connected 5 SG Signal Ground Connected to internal circuit 6 Not connected 7 RS Connected to internal circuit 8 CS Connected to internal circuit 9 Not connected Note • Pin 8 (CS) and Pin 7 (RS) are short circuited inside the projector. RS-232C Cable recommended connection: 9-pin D-sub female connector Pin No. Signal Pin No. Signal 1 CD 1 CD 2 RD 2 RD 3 SD 3 SD 4 ER 4 ER 5 SG 5 SG 6 DR 6 DR 7 RS 7 RS 8 CS 8 CS 9 CI 9 CI Note • Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. Computer). USB Terminal: 4-pin B-type USB female connector LAN Terminal : 8-pin RJ-45 modular connector Pin No. Signal Signal Name Pin No. Signal Pin No. Signal 1 VCC USB power 1 TX+ 5 2 USB– USB data– 2 TX– 6 RX– 3 USB+ USB data+ 3 RX+ 7 4 SG GND 4 8 8 9 6 5 1 2 4 3 7 1 6 11 5 15 10 INPUT 1/INPUT 2 and OUTPUT RGB Signal Terminal: 15-pin Mini D-sub female connector Connecting Pin Assignments RGB Input 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Not connected 5. Not connected 6. Earth (red) 7. Earth (green/sync on green) 8. Earth (blue) 9. Not connected 10. GND 11. Not connected 12. Bi-directional data 13. Horizontal sync signal: TTL level 14. Vertical sync signal: TTL level 15. Data clock Component Input 1. PR (CR) 2. Y 3. PB (CB) 4. Not connected 5. Not connected 6. Earth (PR) 7. Earth (Y) 8. Earth (PB) 9. Not connected 10. Not connected 11. Not connected 12. Not connected 13. Not connected 14. Not connected 15. Not connected 1 5 6 9 5 1 9 6 1 2 4 3 8...1 Projector Pin No. 4 5 6 Computer Pin No. 4 5 6

AV Mute : ON Keystone (-127 ~ +127) INPUT1 (RGB1) INPUT2 (RGB2) Freeze : ON Freeze : OFF Auto Sync Start INPUT3 (Video) INPUT4 (S-Video) _ _ _ 0 _ _ _ 1 ? ? ? ? _ _ _ 1 _ _ _ 1 _ _ * * _ _ _ 0 _ _ _ 1 * * * * _ _ _ 1 _ _ _ 2 _ _ _ 1 _ _ _ 2 _ _ _ 0 _ _ _ 1 _ _ _ 1 P O W R P O W R P O W R T A B N T L P S V O L A I M B K I M B K K E Y S I R G B I R G B I V E D I V E D F R E Z F R E Z A D J S OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR 0 : Standby, 1 : ON 0 : OFF, 1 : ON, 2 : Retry, 3 : Waiting, 4 : Lamp Error 0 : Normal, 1 : Temp High, 2 : Fan Err, 8 : Lamp 5% or less, 16 : Lamp Burnt-out, 32 : Lamp Not Ignition Failure, 64 : Temp Abnormally High Control Contents Return Command Parameter Return code (0DH) C1 C2 C3 C4 P1 P2 P3 P4 Response code format Normal response Problem response (communication error or incorrect command) O K E R R Command 4-digit Parameter 4-digit Command format Return code (0DH) Return code (0DH) Computer control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, commercially available) to the projector. (See page 27 of the projector’s operation manual for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate*: 9,600 bps / 115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None *Set the projector’s baud rate to the same rate as used by the computer. Basic format Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer. Info • When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands. • If more than one command will be sent to the projector, wait for projector reply before sending next com- mand. Note • Use “POWR????” and “TLPS___1” for projector polling. • When the projector receives these commands, the on-screen display will not disappear and these com- mands will not reset the “Auto Power Off” function timer when no signal is present. Commands Example: When turning on the projector, make the following setting. RS-232C Specifications and Commands → ← P O W R _ 1 _ _ O K Projector Computer

Note • If an underbar (_) appears in the parameter column, enter a space. • If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under Control Contents. *1 Parameters of CLR Temp settings are as follows. *2 For setting the projector name, send the commands in order of PJN1, PJN2 and PJN3. CLR Temps Parameter 5500K _ 0 5 5 6500K _ 0 6 5 7500K _ 0 7 5 8500K _ 0 8 5 9300K _ 0 9 3 10500K _ 1 0 5 Control Contents Parameter Command Control Contents Parameter Command _ _ _ 1 _ _ _ 3 _ _ _ 6 _ _ _ 2 _ _ _ 1 _ _ _ 3 _ _ _ 6 _ _ _ 2 _ _ _ 1 _ _ _ 3 _ _ _ 2 _ _ _ 1 _ _ _ 3 _ _ _ 2 _ _ _ 1 _ _ 1 0 _ _ 1 1 _ _ 1 2 _ _ 1 3 _ _ 1 0 _ _ 1 1 _ _ 1 2 _ _ 1 3 _ _ 1 0 _ _ 1 1 _ _ 1 2 _ _ 1 3 _ _ 1 0 _ _ 1 1 _ _ 1 2 _ _ 1 3 _ _ * * _ _ * * _ _ * * _ _ * * _ * * * _ * * * _ * * * _ * * * _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 1 _ _ _ 3 _ _ _ 0 _ _ _ 1 _ _ _ 2 _ _ _ 0 _ _ _ 1 _ _ _ 2 _ _ _ 1 _ _ _ 1 _ _ _ 1 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 1 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 1 _ _ _ 2 _ _ _ 3 _ _ _ 4 _ _ _ 5 _ _ _ 6 _ _ _ 7 _ _ _ 8 _ _ _ 1 _ _ _ 3 _ _ _ 4 _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 1 _ _ _ 2 _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 0 _ _ _ 1 _ _ _ 1 _ _ _ 1 _ _ _ 2 _ _ _ 3 _ _ _ 4 _ _ _ 5 _ _ _ 6 _ _ _ 7 _ _ _ 8 _ _ _ 9 _ _ 1 0 _ _ 1 1 _ _ _ 1 _ _ _ 1 _ _ _ 1 * * * * * * * * * * * * Return Return OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR 0 - 9999 0 - 100 OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR XGMB70X XG-MB70X XG-MB70X R A S R R A S R R A S R R A S R R B S R R B S R R B S R R B S R R A S V R A S V R A S V R B S V R B S V R B S V A F S T R A P S R A P S R A P S R A P S R B P S R B P S R B P S R B P S V A P S V A P S V A P S V A P S V B P S V B P S V B P S V B P S R A W E R B W E V A W E V B W E R A C T R B C T V A C T V B C T C S R A C S R A C S R B C S R B I R I S I R I S I A S I I A S I I A S I I B S I I B S I I B S I R A R E R B R E V A R E V B R E A A D J A A D J T L T T T L T L I M D I I M D I M E S Y M E S Y M E S Y M E S Y M E S Y M E S Y M E S Y M E S Y I M B G I M B G I M B G T H M D T H M D A P O W A P O W A T A F A T A F A T K S A T K S A S P K A S P K A O U T A O U T I M R E I M R E I M I N I M I N M O U T M O U T L N R S L N R S A L R E M E L A M E L A M E L A M E L A M E L A M E L A M E L A M E L A M E L A M E L A M E L A T N A M M N R D P J N 1 P J N 2 P J N 3 P J N 0 Lamp Usage Time (hour) Remaining Lamp Life (Percentage) OSD Display : OFF OSD Display : ON Video System : Auto Video System : PAL Video System : SECAM Video System : NTSC4.43 Video System : NTSC3.58 Video System : PAL-M Video System : PAL-N Video System : PAL-60 Background : Logo Background : Blue Background : None Eco Mode : Standard Eco Mode : Low Power Auto Power Off : Disable Auto Power Off : Enable Auto Focus : OFF Auto Focus : ON Auto Keystone : OFF Auto Keystone : ON Speaker : OFF Speaker : ON Audio Out : FAO Audio Out : VAO PRJ Mode : Reverse Off PRJ Mode : Reverse On PRJ Mode : Invert Off PRJ Mode : Invert On Monitor Out : Disable Monitor Out : Enable LAN/RS232C : Disable LAN/RS232C : Enable All Reset Language : ENGLISH Language : DEUTSCH Language : ESPAÑOL Language : NEDERLANDS Language : FRANÇAIS Language : ITALIANO Language : SVENSKA Language : Language : PORTUGUÊS Language : Language : Model Name Check Model Name Check 2 Projector Name Setting 1 (First four characters)* 2 Projector Name Setting 2 (Middle four characters)* 2 Projector Name Setting 3 (Last four characters)* 2 Projector Name Check INPUT 1 Bright Boost (0 -10) INPUT 2 Bright Boost (0 -10) INPUT 3 Bright Boost (0 -10) INPUT 4 Bright Boost (0 -10) INPUT 1 CLR Temp * 1 INPUT 2 CLR Temp * 1 INPUT 3 CLR Temp * 1 INPUT 4 CLR Temp * 1 INPUT 1 sRGB : OFF INPUT 1 sRGB : ON INPUT 2 sRGB : OFF INPUT 2 sRGB : ON IRIS : High Brightness IRIS : High Contrast INPUT1 Signal Type : Auto INPUT1 Signal Type : RGB INPUT1 Signal Type : Component INPUT2 Signal Type : Auto INPUT2 Signal Type : RGB INPUT2 Signal Type : Component INPUT1 Adjustment Reset INPUT2 Adjustment Reset INPUT3 Adjustment Reset INPUT4 Adjustment Reset Auto Sync : OFF Auto Sync : ON INPUT1 Resize : Normal INPUT1 Resize : Dot By Dot INPUT1 Resize : Border INPUT1 Resize : Stretch INPUT2 Resize : Normal INPUT2 Resize : Dot By Dot INPUT2 Resize : Border INPUT2 Resize : Stretch INPUT3 Resize : Normal INPUT3 Resize : Border INPUT3 Resize : Stretch INPUT4 Resize : Normal INPUT4 Resize : Border INPUT4 Resize : Stretch Auto Focus Start INPUT 1 Picture Mode : Standard INPUT 1 Picture Mode : Presentation INPUT 1 Picture Mode : Cinema INPUT 1 Picture Mode : Game INPUT 2 Picture Mode : Standard INPUT 2 Picture Mode : Presentation INPUT 2 Picture Mode : Cinema INPUT 2 Picture Mode : Game INPUT 3 Picture Mode : Standard INPUT 3 Picture Mode : Presentation INPUT 3 Picture Mode : Cinema INPUT 3 Picture Mode : Game INPUT 4 Picture Mode : Standard INPUT 4 Picture Mode : Presentation INPUT 4 Picture Mode : Cinema INPUT 4 Picture Mode : Game

Setting up the Projector Network Environment This section describes the basic procedure for using the projector via the network. If the network is already constructed, the projector’s network settings may need to be changed. Please consult your network administrator for assistance with these settings. Connect a LAN cable (category 5, cross-over type) between the computer and projector. Pages 8, 9 2. Setting an IP address for the computer Adjust the IP settings of the computer to enable one-to-one communications with the projector. Page 10 3. Setting up a network connection for the projector Adjust the projector network settings to conform to your network. LAN cable (commercially available) Use Internet Explorer (version 5.0 or later) to make various projector settings. Temporarily change the computer’s IP address. • Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other countries. • All other company or product names are trademarks or registered trademarks of their respective compa- nies.

1. Connecting the Pro- jector to a Computer Establishing a one-to-one connection from the projector to a computer. Using a LAN cable (Category 5, cross-over type) you can config- ure the projector via the computer. 1 Disconnect the computer’s LAN cable from the existing network. 2 Connect a LAN cable (a UTP cable, Category 5, cross-over type) to the projector’s LAN ter- minal and connect the other end of the cable to the computer’s LAN terminal. 3 Turn on the projector. 4 Turn on the Computer. Info Confirm that the LINK LED on the rear of the projector illuminates. If the LINK LED does not illuminate, check the following : • The LAN cable is properly connected. • The power switches of both the projector and the computer are on. LAN cable (cross-over type, commercially available) ON ON A LAN cable being connected to the network This completes the connection. Now proceed to “2. Setting an IP Address for the Com- puter”.

2. Setting an IP Address for the Computer The following describes how to make settings in Windows® XP (Professional or Home edi- tion). 1 Log on the network using the administrator’s account for the computer. 2 Click the “Start” button, and click “Control Panel”. 3 Click “Network and Internet Con- nections”, and click “Network Connections” in the new win- dow. • This manual uses examples to explain the operations in Category View. If you are using Classic View, double-click “Network Connections”. 4 Right-click “Local Area Connec- tion” and select “Properties” from the menu. 1 2 1 2 1 2

1 2 After confirming or setting, proceed to “3. Setting up Network Environment for the Projec- tor”. 5 Click “Internet Protocol (TCP/IP)”, and click the “Properties” button. 6 Confirm or change an IP address for the setup computer. 1 Confirm and note the current IP ad- dress and Subnet mask. Make sure to note the current IP ad- dress and Subnet mask as you will be required to reset it later. 2 The factory default setting for the pro- jector IP address is “192.168.150.2”. Set an IP address temporarily as fol- lows : IP Address : 192.168.150.3 7 After setting, click the “OK” but- ton, and then restart the com- puter.

3. Setting up a Network Connection for the Projector Settings for such items as the projector’s IP address and subnet mask are compatible with the existing network. 1 Start Internet Explorer (version 5.0 or later) on the computer, and enter “http://192.168.150.2/” in “Address”, and then press the “Enter” key. 2 If a user name and a password have not yet been set, just click the “OK” button. • If a user name and a password have been set, input the user name and the password, and click the “OK” button. • If the user name or password is entered incorrectly three times, an error mes- sage will be displayed. 3 When the screen as shown on the right appears, click “TCP/IP”.

pears, ready for network settings for the projector. Note • Confirm the existing network’s segment (IP address group) to avoid setting an IP ad- dress that duplicates the IP addresses of other network equipment or computers. If “192.168.150.2” is not used in the network having an IP address of “192.168.150.XXX”, you don’t have to change the projector IP address. • For details about each setting, consult your network administrator. 5 Click the “Apply” button. 6 The set values appear. Confirm that the values are set properly, and then click the “Confirm” but- ton. After setting items, wait for 10 seconds and then re-access. Setting up the Projector Network Environment This completes the network settings. Change the IP address of the setting computer back to its original address, and then con- nect the computer and the projector to the network. Setting example / Remarks Factory default setting: 192.168.150.2 Enter an IP address appropriate for the network. Factory default setting: 255.255.255.0 Set the subnet mask to the same as that of the computer and equipment on the network. Factory default setting: 0.0.0.0 * When not in use, set to “0.0.0.0”. Factory default setting: 0.0.0.0 * When not in use, set to “0.0.0.0”. Items IP Address Subnet Mask Default Gateway DNS Server

Controlling the Projector Using Internet Explorer (Version 5.0 or later) Complete connections to external equipment before starting the operation. (See pages 21- 28 of the projector’s operation manual.) Complete the AC cord connection. (See page 29 of the projector’s operation manual.) Note • When connecting the projector to the LAN, use a LAN cable (Category 5). When connecting the projector to a hub, use a straight-through cable. 1 Start Internet Explorer (version 5.0 or later) on the computer. 2 Enter “http://” followed by the projector IP address set by the procedure on page 11 followed by “/” in “Address”, and then press the “Enter” key. The factory default setting for the projector IP address is 192.168.150.2. If you did not change the IP address in “3. Setting up a Network Connection for the Projector” (page 10–11), enter “http://192.168.150.2/”. 3 A screen for controlling the pro- jector appears, ready for per- forming various status condi- tions, control, and settings. After connecting the projector to your network, enter the projector IP address in “Address” on Internet Explorer (Version 5.0 or later) using a computer on the network to start a setup screen that will enable control of the projector via the network.

Status (Status) On this screen, you can confirm the projector status. You can confirm the following items : ••••• MAC Address ••••• Power ••••• Condition ••••• Lamp Timer ••••• Lamp Life ••••• Input ••••• Signal Info Note • If you click the “Refresh” button before the screen is displayed completely, an error message (“Server Busy Error”) will be dis- played. Wait for a moment and then oper- ate again. • For details about each item, refer to the projector’s operation manual. Controlling the Projector via LAN Controlling the Projector (Control) On this screen, you can perform projector control. You can control the following items : ••••• Power ••••• Input Select ••••• Volume ••••• AV Mute [OFF] [ON] Note • If you click the “Refresh” button before the screen is displayed completely, an error mes- sage (“Server Busy Error”) will be displayed. Wait for a moment and then operate again. • You cannot operate this page while the pro- jector is warming up. • While the projector is in standby mode, you can only control “Power ON”. • For details about each item, refer to the projector’s operation manual.

Setting and Adjusting the Projector (Setting & Adjustment) Example: “Picture” screen display for INPUT 1 On these screens, you can make projector settings or adjustments. You can set or adjust the following items : ••••• Picture Mode ••••• Bright Boost ••••• CLR Temp ••••• sRGB [OFF][ON] ••••• IRIS ••••• Signal Type ••••• Auto Sync [OFF][ON] ••••• Resize (INPUT 1) ••••• OSD Display [OFF][ON] ••••• Video System (INPUT 3/4) ••••• Background ••••• Eco Mode [OFF][ON] ••••• Auto Power Off [OFF][ON] ••••• Auto Focus (Startup) [OFF][ON] ••••• Auto Keystone [OFF][ON] ••••• Internal Speaker [OFF][ON] ••••• Audio Out [OFF][ON] ••••• Projection Mode ••••• RS-232C Speed ••••• Monitor Out (Standby) ••••• OSD Language Note • If you click the “Refresh” button before the screen is displayed completely, an error mes- sage (“Server Busy Error”) will be displayed. Wait for a moment and then operate again. • You cannot operate this page while the pro- jector is warming up. • For details about each item, refer to the projector’s operation manual. Setting the Security (Network – Security) On this screen, you can make settings relat- ing to security. Note • User Name and Password can be up to 8 characters. • You can input the characters below : a-z, A-Z, 0-9, -, _ Description Setting of user name for security protection. Setting of password for security protection. It is possible to set up to three IP addresses allowing connec- tion to the projector. No limits are set to IP addresses connecting to the projector. For security improvement, only an IP address set by “Address 1-3” can be connected to the projector. Items User Name Password Accept IP Addres All IP Addresses From only specific IP address

Making General Settings for the Network (Network - General) On this screen, you can make general settings relating to the network. After clicking the “Apply” button, the set val- ues appear. Confirm that the values are set properly, and then click the “Confirm” but- ton. Note • After setting items, wait for 10 seconds and then re-access. • Projector Name can be up to 12 characters. • You can input the characters below : A-Z, 0-9, -, _, (,), space (When “a-z” are input, they are converted to “A-Z” automatically.) Description Setting the projector name. Setting the time interval in which the projector will be automatically disconnected from the network in units of a minute (from 1 to 65535 minutes). If the set value is made 0, the Auto Logout function is disabled. Setting the TCP port number used when exchanging a data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). Items Projector Name Auto Logout Time Data Port Search Port Setting for Sending E-mail when an Error Occurs (Mail – Originator Setting) On this screen, you can make settings for sending e-mail to report when the projector has generated an error. Note • SMTP Server, Originator E-mail Address and Originator Name can be up to 64 characters. • You can input the characters below: SMTP Server and Originator E-mail Address : a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ’, ., @, ` (You can input “@” only one time for “Origi- nator E-mail Address”.) Originator Name : a-z, A-Z, 0-9, -, _, (,), space Setting example / Remarks Setting an SMTP server address for e-mail transmis- sion. e.g.1 : 192.168.150.253 e.g.2 : smtp123.sharp.co.jp * When using a domain name, make settings for the DNS server. Setting the projector’s e-mail address. The e-mail address set here becomes Originator E-mail Address. Setting the sender’s name. The name set here appears in the “Originator Name” column of the body of the message. Items SMTP Server Originator E-mail Address Originator Name

Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail – Recipient Setting) On this screen, you can input e-mail destina- tions to which error notification (error items) e-mails are sent. Note • E-mail Address can be up to 64 characters. • You can input the characters below : a-z, A-Z, 0-9, -, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ’, ., @, ` (You can input “@” just one time.) • For details about error items, refer to the projector’s operation manual. Description Set addresses to which error notification e-mail is sent. You can set up to five addresses. Error e-mail is sent on the error items checked in their check boxes. Send test e-mail. This allows you to confirm that the settings for e-mail transmission are properly set. Items E-mail Address Error Mail (Lamp, Temp, Fan) Test

When Connecting Using RS-232C 1 Launch general purpose terminal emulator. 2 Input settings for the RS-232C port of the terminal emulator as follows. Baud Rate : 9600 bps* Data Length : 8 bit Parity Bit : None Stop Bit : 1 bit Flow Control : None ∗This is the factory default setting. If the value of Baud Rate for the projector has been changed, set Baud Rate here according to the changed value on the projector. 3 Input “PJS11234” and press the “Enter” key. 4 “OK” is displayed. Input “PJS25678” and press the “Enter” key within 10 seconds. 5 “User Name:” is displayed. Input the user name and press the “Enter” key. • If a user name has not yet been set, just press the “Enter” key. 6 “Password:” is displayed. Input the password and press the “Enter” key. • If a password has not yet been set, just press the “Enter” key. Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector. 7 Input “setup” and press the “Enter” key. • SETUP MENU will be displayed. Note • User name and password are not set in the fac- tory default settings. • If the user name or password is entered incor- rectly three times, SETUP MENU will be quit. ▼SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>

When Connecting Using Telnet 1 Click “Start” from the Windows® desk- top and select “Run”. 2 Enter “telnet 192.168.150.2” in the text box that opens up. (If the IP address of the projector is 192.168.150.2.) 3 Click the “OK” button. 4 “User Name:” is displayed. Input the user name and press the “Enter” key. • If a user name has not yet been set, just press the “Enter” key. 5 “Password:” is displayed. Input the password and press the “Enter” key. • If a password has not yet been set, just press the “Enter” key. 6 Input “setup” and press the “Enter” key. • SETUP MENU will be displayed. Note • If the IP address has been changed, ensure to enter the new IP address in step 2. • User name and password are not set in the fac- tory default settings. • If the user name or password is entered incor- rectly three times in steps 4 or 5, SETUP MENU will be quit. ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> ▼SETUP MENU

SETUP MENU (Main Menu) [1]IP Address (Factory default setting : 192.168.150.2) IP address settings. (Page 22) [2]Subnet Mask (Factory default setting : 255.255.255.0) Subnet mask settings. (Page 22) [3]Default Gateway (Factory default setting : Not Used) Default gateway settings. (Page 22) [4]User Name (Factory default setting : Not Re- quired) Setting of user name for security protection. (Page 23) [5]Password (Factory default setting : Not Required) Setting of password for security protection. (Page 23) [6]RS-232C Baud Rate (Factory default setting : 9600 bps) Baud rate settings for the RS-232C terminals. (Page 23) [7]Projector Name (Factory default setting : XG- MB70X) It is possible to assign a projector name. (Page 23) [A]Advanced Setup Enters ADVANCED SETUP MENU. (Page 24) [D]Disconnect All Disconnect all connections. (Page 24) [V]View All Setting Displays all setting values. (Page 20) Can also be used with ADVANCED SETUP MENU. [S]Save & Quit Save set values and quit menu. (Page 21) [Q]Quit Unchanged Quit menu without saving setting values. (Page 21) ADVANCED SETUP MENU [1]Auto Logout Time (Factory default setting : 5 min- utes) Setting of time until automatic disconnection of net- work connection. (Page 24) [2]Data Port (Factory default setting : 10002) Setting the TCP port number used when exchang- ing data. (Page 24) [5]Network Ping Test It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally. (Page 25) [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr (Factory default setting : Ac- cept All) For improved security, it is possible to set up to three IP addresses allowing connection to the projector. Set IP addresses can be cancelled using [9] Accept All IP Addr. (Page 25) [0] Search Port (Factory default setting : 5006) Setting the port number used when searching for the projector. (Page 26) [ ! ]Restore Default Setting Restores all setting values that can be set using the menu to the default state. (Page 26) [Q]Return to Main Menu Return to the main SETUP MENU. (Page 26) ▼SETUP MENU ▼ADVANCED SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> ******************** ADVANCED SETUP MENU *********************** [1]Auto Logout Time [2]Data Port [5]Network Ping Test [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr [0]Search Port [!]Restore Default Setting [Q]Return to Main Menu advanced>

View Setting Detail List ([V]View All Setting) 1 1 1 1 1 Enter “v” and press the “Enter” key. Display all setting values(*). Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the details to be set. Setting is carried out one item at a time, and saved at the end. ▼SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>v Model Name : XG-MB70X Projector Name : XG-MB70X MAC Address : 08:00:1f:b1:b7:74 IP Address : 192.168.150.2 Subnet Mask : 255.255.255.0 Default Gateway : Not Used RS-232 Baud Rate : 9600 bps Password : Not Required **********(Advanced Status)********** Data Port : 10002 Accept IP Address : Accept All Auto Logout Time : 5 minutes Search Port : 5006 1 * Set Items Example: When setting IP Address (change from 192.168.150.2 to 192.168.150.3) 1 1 1 1 1 Enter “1” (number of item to be set), and press the “Enter” key. Display current IP address (*1). 2 2 2 2 2 Enter IP address to be set and press the “En- ter” key. Display IP address after change (*2). 3 3 3 3 3 Enter “v” and press the “Enter” key to verify setting detail list. IP address is being changed (*3). Note • Verification of setting detail list can be omitted. • Setting details are not effective until they have been saved. (Page 21) • If an invalid number is entered, an error message (“Parameter Error!”) will be displayed. ▼SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>1 IP Address : 192.168.150.2 Please Enter : 192.168.150.3 (change) —> 192.168.150.3 ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>v Model Name : XG-MB70X Projector Name : XG-MB70X MAC Address : 08:00:1f:b1:b7:74 IP Address : 192.168.150.3 Subnet Mask : 255.255.255.0 Default Gateway : Not Used RS-232C Baud Rate : 9600 bps Password : Not Required **********(Advanced Status)********** Data Port : 10002 Accept IP Address : Accept All Busy Reply : ERR+ code Input Hold Time : 1000 milliseconds Auto Logout Time : 5 minutes Search Port : 5006 1 2 3 *1 *2 *3

Save Settings and Quit ([S]Save & Quit) Save set values and quit menu. 1 1 1 1 1 Enter “s” and press the “Enter” key. 2 2 2 2 2 Enter “y” and press the “Enter” key. ▼SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>s All Connection will be disconnect. Continue(y/n)? y Apply New setting...Done. 1 2 Quit without Saving Set- tings ([Q]Quit Unchanged) Quit menu without saving setting values. 1 1 1 1 1 Enter “q” and press the “Enter” key. 2 2 2 2 2 Enter “y” and press the “Enter” key. ▼SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>q Quit Without Saving(y/n)? y Setting Unchanged. 1 2

IP Address Setting ([1]IP Address) Setting of IP address. 1 1 1 1 1 Enter “1” and press the “Enter” key. 2 2 2 2 2 Enter numerical value to be set and press the “Enter” key. Display IP address after change (*). Subnet Mask Setting ([2]Subnet Mask) Setting subnet mask. 1 1 1 1 1 Enter “2” and press the “Enter” key. 2 2 2 2 2 Enter numerical value to be set and press the “Enter” key. Display subnet mask after change (*). The setting procedure for each item will be explained. For the basic procedure, please refer to “Set Items” on page 20. setup>1 IP Address :192.168.150.2 Please Enter :192.168.150.3 (change) —> 192.168.150.3 1 2 * setup>2 Subnet Mask :255.255.255.0 Please Enter :255.0.0.0 (change) —> 255.0.0.0 1 2 * Default Gateway Setting ([3]Default Gateway) Setting default gateway. 1 1 1 1 1 Enter “3” and press the “Enter” key. 2 2 2 2 2 Enter numerical value to be set and press the “Enter” key. Display gateway address after change (*). Note • If the values for IP Address, Subnet Mask or Gate- way of the projector have been changed via Telnet, the computer for controlling cannot be connected to the projector depending on the computer’s net- work settings. setup>3 note: “0.0.0.0” means “Using no default gateway.” Gateway Address :0.0.0.0 Please Enter :192.168.150.1 (change) —> 192.168.150.1 1 2 *

User Name Setting ([4]User Name) Carrying out security protection using user name. 1 1 1 1 1 Enter “4” and press the “Enter” key. 2 2 2 2 2 Enter user name and press the “Enter” key. Display set user name (*). Note • User name can be up to 8 characters. • You can input the characters below : a-z, A-Z, 0-9, -, _ • In the default state, user name is not set. Password Setting ([5]Password) Carrying out security protection using password. 1 1 1 1 1 Enter “5” and press the “Enter” key. 2 2 2 2 2 Enter password and press the “Enter” key. Display set password (*). Note • Password can be up to 8 characters. • You can input the characters below : a-z, A-Z, 0-9, -, _ • In the default state, the password is not set. setup>4 User Name : Please Enter : XG-MB70X (change) —> XG-MB70X 1 2 * setup>5 Password : Please Enter : sharppj (change) —> sharppj 1 2 * RS-232C Baud Rate Set- ting ([6]RS-232C Baud Rate) Setting of baud rate for RS-232C (COMPUTER and PROJECTOR) terminals. 1 1 1 1 1 Enter “6” and press the “Enter” key. 2 2 2 2 2 Select and enter the number 0 or 2 and press the “Enter” key. Display set baud rate (*). Note • Set the projector’s baud rate to the same rate as that used by the computer. Projector Name Setting ([7]Projector Name) It is possible to assign a projector name. 1 1 1 1 1 Enter “7” and press the “Enter” key. 2 2 2 2 2 Enter projector name. Display set projector name (*). Note • Projector name can be up to 12 characters. • You can input the characters below : A-Z, 0-9, -, _, (,), space (When “a-z” are input, they are converted to “A-Z” automatically.) • It is the same as the name which can be con- firmed or set, using RS-232C commands “PJN0”, “PJN1”, “PJN2” and “PJN3”. setup>6 note: It sets both RS-232C (COMPUTER) and RS-232C (PROJECTOR). 0 ... 9600 bps 2 ... 115200 bps Baud Rate Select[0, 2] :2 RS-232C Baud Rate : 115200 bps 1 2 * setup>7 Projector Name : XG-MB70X Please Enter : MY XG-MB70X (change) —> MY XG-MB70X 1 2 *

Disconnecting All Connec- tions ([D]Disconnect All) It is possible to disconnect all the TCP/IP connec- tions currently recognized by the projector. Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection. 1 1 1 1 1 Enter “d” and press the “Enter” key. 2 2 2 2 2 Enter “y” and press the “Enter” key. Note • If Disconnect All is performed, the connection to the projector via network will be forcibly discon- nected. Entering ADVANCED SETUP MENU ([A]Advanced Setup) Enters ADVANCED SETUP MENU. 1 1 1 1 1 Enter “a” and press the “Enter” key. Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) If there is no input after a fixed time, the projector automatically disconnects network connection using the Auto Logout function. It is possible to set the time until the projector is automatically disconnected in units of a minute (from 1 to 65535 minutes). 1 1 1 1 1 Enter “1” and press the “Enter” key. 2 2 2 2 2 Enter numerical value and press the “Enter” key. Display set numerical value (*). Note • If the set value is made 0, the Auto Logout func- tion is disabled. • If an invalid number is entered, an error message (“Parameter Error!”) will be displayed and returns the ADVANCED SETUP MENU. Data Port Setting (ADVANCED[2]Data Port) Setting of TCP port number can be set in the range of 1025 to 65535. 1 1 1 1 1 Enter “2” and press the “Enter” key. 2 2 2 2 2 Enter numerical value and press the “Enter” key. Display set numerical value (*). Note • Set according to need. Normally, use with the fac- tory default setting. setup>d Disconnect All Connections(y/n)?y Now Disconnecting... 1 2 setup>a ******************** ADVANCED SETUP MENU *********************** [1]Auto Logout Time [2]Data Port [5]Network Ping Test [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr [0]Search Port [!]Restore Default Setting [Q]Return to Main Menu advanced> 1 advanced>1 Valid range : 0 to 65535 (minute) note: if you enter “0”, auto logout function will be disable. Auto Logout Time : 5 Please Enter :15 (change) —> 15 1 2 * advanced>2 Valid range :1025 to 65535 Data Port :10002 Please Enter :10005 (change) —> 10005 1 2 *

Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally. 1 1 1 1 1 Enter “5” and press the “Enter” key. 2 2 2 2 2 Enter IP address of device to be tested and press the “Enter” key. Display entered IP address (*1). Display test result (*2). Note • If the “Enter” key is pressed without entering an IP address, the Ping destination IP address used previously is entered. • If there is a fault with the connection, “Error: No answer” is displayed after a 5 second retry. In this case, please confirm the settings for the projector and the computer, and contact your network ad- ministrator. Setting of Accept IP Ad- dress (ADVANCED[6]Accept IP Addr(1) - [8]Accept IP Addr(3)) It is possible to improve security of the projector by allowing connection from only a prescribed IP ad- dress. It is possible to set up to three IP addresses allowing connection to the projector. 1 1 1 1 1 Enter “6”, “7” or “8” and press the “Enter” key. 2 2 2 2 2 Enter numerical value and press the “Enter” key. Display set numerical value (*). Note • To invalidate the Accept IP Address being cur- rently set, enter “0.0.0.0”. • If there is one or more Accept IP Addr being set, no connections are allowed from IP addresses that are not yet set. They can be cancelled using [9]Accept All IP Addr. Accepting All IP Addresses (ADVANCED[9]Accept All IP Addr) Removes IP addresses set with “Accept IP Addr”. 1 1 1 1 1 Enter “9” and press the “Enter” key. 2 2 2 2 2 Enter “y” and press the “Enter” key. Note • At the point in time where “y” was entered, the numerical values for Accept IP Addr(1)-(3) are reset to ”0.0.0.0”. • If “n” is entered, setting is not altered. advanced>5 Ping dest IP addr :192.168.150.1 Please Enter :192.168.150.152 (change) —> 192.168.150.152 32 bytes from 192.168.150.152: icmp_seq = 1, time = 0 ms 32 bytes from 192.168.150.152: icmp_seq = 2, time = 0 ms 32 bytes from 192.168.150.152: icmp_seq = 3, time = 0 ms 32 bytes from 192.168.150.152: icmp_seq = 4, time = 0 ms 1 2 *1 *2 advanced>6 Accept IP Addr(1) : 0.0.0.0 Please Enter : 192.168.150.152 (change) —> 192.168.150.152 1 2 * advanced>9 Accept All IP Addresses(y/n)? y 1 2

Setting of Search Port (ADVANCED[0]Search Port) Sets the port number used when searching for the projector from the network. 1 1 1 1 1 Enter “0” and press the “Enter” key. 2 2 2 2 2 Enter numerical value and press the “Enter” key. Display set numerical value (*). Note • Set according to need. Normally, use with the fac- tory default setting. Return to Default Settings (ADVANCED[!]Restore Default Setting) Returns all menu setting values to the default state. 1 1 1 1 1 Enter “!” and press the “Enter” key. 2 2 2 2 2 Enter “y” and press the “Enter” key. Note • If the values for IP Address, Subnet Mask or Gate- way of the projector have been returned to the default settings via Telnet, the computer for con- trolling cannot be connected to the projector de- pending on the computer’s network settings. Return to Main Menu (ADVANCED[Q]Return to Main Menu) Returns to the main SETUP MENU. 1 1 1 1 1 Enter “q” and press the “Enter” key. Returns to the SETUP MENU. advanced>0 Please Enter Port Number for Search from Computer. Valid range : 1025 to 65535 Search Port : 5006 Please Enter : 5004 (change) —> 5004 1 2 * advanced>! Restore All Setting to Default(y/n)? y — User Setting Initialized — 1 2 advanced>q ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> 1

When connecting the projector using serial-connection \ Check that the RS-232C terminal of the projector and a computer or the commercially available controller are connected correctly. \ Check that the RS-232C cable is a cross-over cable. \ Check that the RS-232C port setting for the projector corresponds to the setting for the computer or the commercially available controller. When connecting the projector to a computer using network (LAN)- connection \ Check that the cable’s connector is firmly inserted in the LAN terminal of the projector. \ Check that the cable is firmly inserted into a LAN port for a computer or a network device such as a hub. \ Check that the LAN cable is a Category 5 cable. \ Check that the LAN cable is a cross-over cable when connecting the projector to a computer directly. \ Check that the LAN cable is a straight-through cable when connecting the projector with a network device such as a hub. \ Check that the power supply is turned on for the network device such as a hub between the projector and a computer. Check the network settings for the computer and the projector \ Check the following network settings for the projector. • IP Address Check that the IP address for the projector is not duplicated on the network. • Subnet Mask When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: • The subnet masks for the projector and the computer should be the same. (Example) When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the subnet mask should be “255.255.255.0”. • Gateway When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: • The subnets for the projector and the computer should be the same. (Example) When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the subnet mask should be “255.255.255.0”. Note • The factory default setting of the network setting for the projector IP address : 192.168.150.2 Subnet mask : 255.255.255.0 Gateway address : 0.0.0.0 (Not Used) • For network settings for the projector, refer to page 10.

1. Open a command prompt (MS-DOS Prompt). • In the case of Windows 98 or 98SE: click “START” ➔ “Programs” ➔ “MS-DOS Prompt” in order. • In the case of Windows Me: click “START” ➔ “Programs” ➔ “Accessories” ➔ “MS-DOS Prompt” in order. • In the case of Windows 2000: click “START” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order. • In the case of Windows XP: click “START” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order. 2. After launching the command prompt (MS-DOS Prompt), enter the command “ipconfig”, and press the “Enter” key. Note • Communication may not be established even after carrying out the network settings for the computer. In such cases, restart your computer. C:\>ipconfig “Enter” Note • Usage examples of ipconfig C:\>ipconfig /? displays how to use “ipconfig.exe”. C:\>ipconfig displays the set IP address, subnet mask and default gateway. C:\>ipconfig /all displays all the setting information related to TCP/IP. 3. To return to the Windows screen, enter “exit” and press the “Enter” key.

if an IP address is set. 1. Open a command prompt (MS-DOS Prompt). • In the case of Windows 98 or 98SE: click “START” ➔ “Programs” ➔ “MS-DOS Prompt” in order. • In the case of Windows Me: click “START” ➔ “Programs” ➔ “Accessories” ➔ “MS-DOS Prompt” in order. • In the case of Windows 2000: click “START” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order. • In case of Windows XP: click “START” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order. 2. After launching the command prompt (MS-DOS Prompt) enter a command “PING”. Entry example C:\>Ping XXX.XXX.XXX.XXX “XXX.XXX.XXX.XXX” should be entered with an IP address to be connected to, such as the projector. 3. When connecting normally, the display will be as follows. (The screen may be slightly different depending on the OS type). when the IP address connected to is “192.168.150.2” 4. When a command cannot be sent, “Request time out” will be displayed. Check the network setting again. If communication can still not be established properly, contact your network administrator. 5. To return to the Windows screen, enter “exit” and then press the “Enter” key. A connection cannot be made because you have forgotten your user name or your password. \ Initialize the settings. \ After the initialization, carry out setting again. Troubleshooting

Side View Side View Top View Rear View Front View Bottom View 1/8 (3.25) 11 7/64 (282) 1/16 (1.5) 2 11/64 (55.05) 12 13/64 (310) 1 29/32 (48.5) 3 1/2 (89) 13/64 (5) 2 3/16 (55.5) 3 15/16 (99.95) 5 3/32 (129.5) 5 3/32 (129.5) 39/64 (15.5) 35/64 (14) 4 3/16 (106.3) 8 9/32 (210.3) 8 7/8 (225.3) 1 7/32 (30.9) 1 9/64 (29.1) 1 7/32 (30.9) 1 47/64 (44.1) M4 M4 M4 M4