Sharp XV-Z200U Operation Manual

MANUAL DE OPERAÇÃO XV-Z200U PROJECTOR PROJECTEUR PROYECTOR PROJETOR ENGLISH ............. -1 – -72 FRANÇAIS ........... -1 – -71 ESPAÑOL ............ -1 – -70 PORTUGUÊS ...... -1 – -70

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE. WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equip- ment. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Introduction ENGLISH CAUTION RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREWS. See bottom of actual set. U.S.A. ONLY U.S.A. ONLY IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 12. Model No.: XV-Z200U Serial No.: PRODUCT DISPOSAL This product utilizes tin-lead solder, and high intensity discharge lamp (HID lamp) containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org .

During normal operation, when putting the projector into the standby mode always use the STANDBY button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. U.S.A. ONLY Declaration of Conformity SHARP PROJECTOR, MODEL XV-Z200U This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430 TEL: 1-800-BE-SHARP (1-800-237-4277) U.S.A. ONLY WARNING: Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof. LAMP REPLACEMENT BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-XVZ200++1 ONLY. UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING. HIGH PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL. DU REMPLACEMENT DE LA LAMPE. PRECAUTIONS A OBSERVER LORS DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS. L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE. NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XVZ200++1. RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX. ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN. LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE. A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI. CAUTION Caution Concerning the Lamp Replacement There is potential glass particles hazard if the lamp ruptures.

Quick Guide ......................................................... 7 Part Names .......................................................... 8 Operating the Remote Control ......................... 11 Accessories ....................................................... 12 Connections & Setup Connecting the Projector to Other Devices.... 14 Connecting the Power Cord ................................... 14 Connecting to Video Equipment .......................... 15 Connecting to a DVD Player and DTV Decoder ..... 17 Connecting to a Computer .................................. 21 Controlling the Projector by a Computer ............. 23 Setup .................................................................. 24 Using the Swivel Stand ............................................24 Removing the Swivel Stand .....................................24 Attaching the Swivel Stand ..................................... 25 Focusing and Zooming ...........................................25 Using the Lens Shift ................................................25 Adjusting the Projection Distance .......................... 26 Image Projection......................................................28 Basic Operation Image Projection ............................................... 30 Basic Procedure ......................................................30 Selecting the On-screen Display Language ...........31 Turning the Power off .............................................. 32 Keystone Correction ................................................33 Placement of the Projected Image Using the Keystone Correction ............................34 Freezing a Moving Image ....................................... 35 Adjusting the Picture Aspect Ratio ..........................35 Adjustments and Settings Using the Menu Screen .................................... 38 Menu Selections (Adjustment) ................................38 Menu Selections (Settings) ..................................... 40 Menu Bar Items ................................................. 42 Adjusting the Picture ........................................ 44 Adjusting Image Preferences ..................................44 Adjusting the Color Temperature ............................ 45 Gamma Correction Function ...................................46 Emphasizing the Contrast .......................................46 Picture Setting Function...........................................47 Adjusting the Computer and DVD/DTV Images ......................................... 48 When Auto Sync is OFF ...........................................48 Special Modes Adjustment .....................................49 Auto Sync Adjustment .............................................50 Checking the Input Signal .......................................50 Using the “Options” Menu ............................... 51 Checking the Lamp Life Status .............................. 51 Turning on/off the On-screen Display ......................51 Selecting the Signal Type ....................................... 52 Setting the Video Signal (VIDEO menu only)...........52 Selecting a Background Image .............................. 53 Setting the Eco Mode ..............................................53 Automatic Power Shut-off Function ........................ 54 Selecting the Menu Screen Position ........................54 Selecting the Menu Color ....................................... 55 Reversing/Inverting Projected Images ............ 56 Appendix Maintenance Indicators .................................... 58 Regarding the Lamp ......................................... 59 Lamp ...................................................................... 59 Caution Concerning the Lamp ................................59 Replacing the Lamp ................................................59 Removing and Installing the Lamp Unit ................. 60 Resetting the Lamp Timer .......................................61 Cleaning the Ventilative Holes ......................... 62 Using the Kensington Lock.............................. 63 Troubleshooting ................................................ 63 For SHARP Assistance (U.S.A. only)............... 63 Connecting Pin Assignments .......................... 64 (RS-232C) Specifications and Command Settings .............................. 65 Computer Compatibility Chart ......................... 66 Specifications .................................................... 67 Dimensions ........................................................ 68 Glossary ............................................................. 69 Index ................................................................... 70 CONSUMER LIMITED WARRANTY (VALID IN USA ONLY) .................................. 71 LIMITED WARRANTY (VALID IN CANADA ONLY) .......................... 72

All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions The safety and operating instructions should be retained for future reference. 3. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions All operating and use instructions should be followed. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture Do not use this product near water–for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8. Accessories Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 9. Transportation A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. The openings should never be covered or blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod- uct should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. IMPORTANT SAFEGUARDS 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization This product is equipped with a three-wire grounding- type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power cord. This will prevent damage to the product due to lightning and power-line surges. 15. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 16. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 17. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dan- gerous voltage or other hazards. Refer all servicing to qualified service personnel. CAUTION: Please read all of these instructions before you operate this product and save them for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to ensure your personal safety. However IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this Projector, observe the following basic rules for its installation, use and servicing. For your own protection and reliable usage of your Projector, please be sure to read these “IMPORTANT SAFEGUARDS” carefully before use.

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. e. If the product has been dropped or damaged in any way. f. If the product exhibits a distinct change in performance. 19. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 20. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 21. Wall or Ceiling Mounting This product should be mounted to a wall or ceiling only as recommended by the manufacturer. 22. Heat This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. • Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. • Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. • PC/AT is a registered trademark of International Business Machines Corporation in the United States. • Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries. • All other company or product names are trademarks or registered trademarks of their respective compa- nies.

your projector. Caution concerning the lamp unit I There is a potential hazard of glass particles if the lamp ruptures. In case of lamp rupture, contact your near- est Authorized SharpVision Service Center or Dealer for replacement. See “Replacing the Lamp” on page 59. Cautions concerning the setup of the projector I For minimal servicing and to maintain high image qual- ity, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens and part of filter must be cleaned more often than usual. As long as the projector is properly main- tained in this manner, use in these environments will not reduce the overall operation life. Please note that all internal cleaning must be performed by an Autho- rized SharpVision Service Center or Dealer. Do not set up the projector in places exposed to direct sunlight or bright light. I Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the cur- tains and dim the lights when setting up the screen in a sunny or bright room. Do not subject the projector to hard impact and/ or vibration. I Take care with the lens so as not to hit or damage the surface of the lens. Rest your eyes occasionally. I Watching the screen for long hours continuously will make your eyes tired. Be sure to occasionally rest your eyes. Do not expose the projector to extreme heat or cold. I Operating temperature: 41°F to 95°F (+5°C to 35°C) I Storage temperature: –4°F to 140°F (–20°C to +60°C) Notes on Operation I The exhaust ventilative holes, the lamp unit cover and adja- cent areas may get extremely hot during projector operation. To prevent injury, do not touch these areas until they have suf- ficiently cooled down. I Allow at least 1 foot (30 cm) of space between the ex- haust ventilative hole and the nearest wall or obstruc- tion. I If the cooling fan becomes obstructed, a protection device will automatically turn off the projector lamp. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. Then turn on the power by plugging the power cord back in. This will return the projector to the normal operating condition. Cautions regarding the transportation of the pro- jector I When transporting the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Take extra caution with the lens. Before mov- ing the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables con- nected to it. Other connected equipment I When connecting other audio-visual equipment or a computer to the projector, make the connections AF- TER turning off the projector and the equipment to be connected. I Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections. Temperature monitor function I If the projector starts to overheat due to setup problems or block- age of the air vents, “ ” and “ ” will blink in the lower left corner of the picture. If the tem- perature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter the standby mode. Refer to “Maintenance In- dicators” on page 58 for details. Info • The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction. 95˚F (+35˚C) 41˚F (+5˚C) CAUTION PRECAUCIÓN PRÉCAUTION BQC-XVZ200++1

illuminates green. In this page, connection of the projector and the video equipment is explained as an example for the procedure from setup to projection. Refer to each page for details. Quick Guide Required equipments Video cable (commercially available) Projector Remote control • Insert the batteries. (Page 11) Power cord 1. Place the projector facing a wall or a screen. 2. Connect to video equipment. (Page 16) 6. Turn the projector on using on the remote control. (Page 30) 3. Connect the output terminal of the video equip- ment to the input terminal of the audio equip- ment using an audio cable. 4. Plug the power cord into the AC socket of the projector and into the wall outlet. (Page 14) 5. Remove the lens cap from the lens. 7. Press on the remote control to select the INPUT 4 mode. (Page 31) "On-screen Display 8. Turn on the video equipment. To INPUT 4 terminal To video out- put terminal INPUT 4 button ON button ON Power cord Video equipment Lens cap Video cable (commercially available) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 9. Play the video. 10.Adjust the image size, image position and the focus. (Page 25) Note • This projector can also be connected to a computer as well as to video equipment. (Page 21) Adjust the height of the image by rotating the lens shift dial. Adjust the focus by rotating the focus ring. Adjust the zooming by moving the zoom knob.

Part Names Numbers in refer to the main pages in this operation manual where the topic is explained. 30 58 58 POWER indicator 6 Exhaust ventilative hole LAMP indicator TEMPERATURE WARNING indicator 39 ADJUSTMENT buttons (ƒ/∂/ß/©) 39 UNDO button 38 MENU button 35 RESIZE button 31 INPUT button 24 Swivel Stand LOCK/UNLOCK lever 11 Remote control sensor Lens cap Zoom knob 25 Exhaust ventilative hole 6 Focus ring 25 25 Lens shift dial 39 ENTER button 33 KEYSTONE button ON button 30 STANDBY button 32 47 PICTURE SETTING button Attaching the Lens Cap The lens cap can be attached to the projector using commercially available straps (for cellular phones etc.), as shown in the figure. Projector (Side and Rear View)

Using the Terminal Cover When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied) to hide the connecting cables. Attaching the Terminal Cover 1 Align with the tabs on the projector and then press the terminal cover in the direction of the arrow. 2 Tighten the two screws on the bottom of the projector. Removing the Terminal Cover 1 Loosen the two screws on the bottom of the projector. 2 Raise the terminal cover and pull it out in the direction of the arrow. 2 Tighten the screws 1 Loosen the screws 1 2 17 16 62 Intake ventilative hole AC socket Intake ventilative hole 62 18 INPUT 2/DIGITAL INPUT terminal INPUT 1 COMPONENT terminals (RCA) INPUT 4 VIDEO terminal (RCA) 20 DIGITAL INPUT TYPE switch 15 INPUT 3 S-VIDEO terminal (4-pin Mini DIN) 23 RS-232C terminal (9-pin D-sub) 11 Remote control sensor 14

Part Names Remote Control (Top View) FREEZE button 32 31 50 52 39 39 38 39 31 31 31 31 35 47 35 STANDBY button ENTER button 33 KEYSTONE button UNDO button INPUT 1 button INPUT 2 button INPUT 4 button AUTO SYNC button RESIZE button PICTURE SETTING button MENU button 30 ON button ADJUSTMENT buttons (ƒ/∂/ß/©) INPUT 3 button DIGITAL INPUT button RGB/COMP. button Remote control signal transmitters

I The remote control can be used to control the projector within the ranges shown in the illustration. Note • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material. When using the remote control: • Be sure not to drop, or expose to moisture or high temperature. • The remote control may malfunction under a fluorescent lamp. Under that circumstance, move the projector away from the fluo- rescent lamp. Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below. Caution • Insert the batteries making sure the polarities correctly match the and marks inside the battery compart- ment. • Batteries of different types have different properties, therefore do not mix batteries of different types. • Do not mix new and old batteries. This may shorten the life of new batteries or may cause old batteries to leak. • Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak. Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove them using a cloth. • The batteries included with this projector may exhaust over a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries when they have run out. • Remove the batteries from the remote control if you will not be using the remote control for a long time. Available Range of the Remote Control 45˚ 23' (7 m) 30˚ 30˚ 45˚ 30˚ Inserting the Batteries The batteries (two “AA” size) are included in the package. 1 Pull down the tab on the cover and remove the cover toward the direction of the arrow. 2 Insert the included batteries. • Insert the batteries making sure the polarities correctly match the and marks inside the battery compart- ment. 3 Insert the lower tab of the cover into the opening, and lower the cover until it clicks in place. Remote control Remote control

Terminal cover GCOVAA116WJKB Operation manual TINS-B005WJZZ Lens cap CCAPHA004WJ01 Screws for terminal cover XBBSN40P10000 Supplied accessories 3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP DVI to 15-pin D-sub adaptor (7.9'' (20 cm)) AN-A1DV DVI cable (9'10'' (3.0 m)) AN-C3DV Note • Some of the cables may not be available depending on the region. Please check with your nearest Autho- rized SharpVision Service Center or Dealer. Optional accessories

Before Connecting Note • Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that it is the last device to be turned on after all the connec- tions are made. • Be sure to read the operation manuals of the devices to be connected before making connections. This projector can be connected to: Video equipment: I A VCR, DVD player or other video equipment (See page 15.) I A DVD player or DTV* decoder (See page 17.) *DTV is the umbrella term used to describe the new digital television system in the United States. A computer using: I DVI to 15-Pin D-sub adapter (See page 21.) I A DVI cable (See page 22.) I An RS-232C cable (See page 23.) Connecting the Power Cord Plug in the supplied power cord into the AC socket on the rear of the pro- jector. Power cord Supplied accessory -14 Power cord

-15 Connecting to Video Equipment S-video cable (commercially available) To S-video output terminal To INPUT 3 terminal VCR or other video equipment Connecting to Video Equipment Using an S-video Cable (INPUT 3) Using an S-video cable, a VCR, DVD player or other video equipment can be connected to INPUT 3 input terminal. 1 Connect an S-video cable to the projector. 2 Connect the S-video cable to the video equipment. Note • The INPUT 3 (S-VIDEO) terminal uses a video signal system in which the picture is separated into color and luminance sig- nals to realize a higher-quality image. To view a higher-quality image, use a com- mercially available S-video cable to con- nect the INPUT 3 terminal on the projec- tor and the S-video output terminal on the video equipment.

VCR or other video equipment To video output terminal Composite video cable (commercially available) Connecting to Video Equipment Using a Composite Video Cable (INPUT 4) Using a composite video cable, a VCR, DVD player or other video equipment can be con- nected to INPUT 4 input terminal. 1 Connect a composite video cable to the projector. 2 Connect the composite video cable to the video equipment. Connecting the Projector to Other Devices -16

-17 Connecting to a DVD Player and DTV Decoder To analog component output terminal To INPUT 1 terminals DVD player or DTV decoder Component cable (commercially available) Connecting to Component Video Equipment Using a Component Cable (INPUT 1) Use a component cable when connecting com- ponent video equipment such as DVD players and DTV decoders to INPUT 1 terminals. 1 Connect a component cable to the projector. 2 Connect the above cable to the component video equipment. Note • Make sure to turn both the projector and the video equipment off before connect- ing.

D-sub cable Type: AN-C3CP (9'10" (3.0 m)) DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm)) Optional accessories Connecting to Compo- nent Video Equipment Using a 3 RCA to 15-pin D-sub Cable and the DVI to 15-pin D-sub Adaptor (INPUT 2) Use a 3 RCA to 15-pin D-sub cable and the DVI to 15-pin D-sub adaptor when connecting com- ponent video equipment such as DVD players and DTV decoders to INPUT 2 terminal. 1 Connect a DVI to 15-pin D-sub adaptor to the projector. 2 Connect a 3 RCA to 15-pin D- sub cable to the above adaptor. • Secure the connectors by tightening the thumbscrews. 3 Connect the above cable to the video equipment. Note • When connecting this projector to com- ponent output terminal of the DTV de- coder, select “Component” for “Signal Type” on the OSD menu or press on the remote control. (See page 52.) • Make sure to turn both the projector and the video equipment off before connect- ing. To analog component output terminal To INPUT 2 terminal DVD player or DTV decoder DVI to 15-pin D-sub adaptor (sold separately) 3 RCA to 15-pin D-sub cable (sold separately) -18 Connecting the Projector to Other Devices

Optional accessory DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm)) Connecting to RGB Video Equipment Using the DVI to 15-pin D-sub Adaptor and the RGB Cable (INPUT 2) Use the DVI to 15-pin D-sub adaptor and the RGB cable when connecting RGB video equip- ment such as DVD players and DTV decoders to INPUT 2 terminal. 1 Connect a DVI to 15-pin D-sub adaptor to the projector. 2 Connect the above adaptor to an RGB cable. 3 Connect the above cable to the video equipment. • Secure the connectors by tightening the thumbscrews. Note • When connecting this projector to DVI out- put of the DTV decoder, select “RGB” for “Signal Type” on the OSD menu or press on the remote control. (See page 52.) To RGB output terminal RGB cable (commercially available) To INPUT 2 terminal DVD player or DTV decoder DVI to 15-pin D-sub adaptor (sold separately) -19

To DIGITAL INPUT terminal DIGITAL INPUT TYPE switch DVD player or DTV decoder To DVI digital output terminal DVI cable (sold separately) -20 Connecting to Video Equipment with the DVI Output Terminal Using a DVI Cable (DIGITAL INPUT) Use the DVI cable when connecting video equipment with the DVI output terminal such as DVD players and DTV decoders to DIGITAL INPUT terminal. 1 Slide the “DIGITAL INPUT TYPE” switch on the back ter- minal board to “VIDEO”. 2 Connect the DVI cable to the DIGITAL INPUT terminal. 3 Connect the other end to the corresponding terminal on the DVD player or DTV decoder. • Secure the connectors by tightening the thumbscrews. Note • Select DIGITAL INPUT mode when con- necting to video equipment with the digital output terminal. (See page 31.) • Make sure to turn both the projector and the video equipment off before switching the “DIGITAL INPUT TYPE” switch and connecting. Connecting the Projector to Other Devices

-21 Connecting to a Computer Optional accessory DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm)) Connecting to a Computer Using the DVI to 15-pin D-sub Adaptor and the RGB Cable (INPUT 2) 1 Connect a DVI to 15-pin D-sub adaptor to the projector. 2 Connect the above adaptor to an RGB cable. 3 Connect the above cable to the computer. • Secure the connectors by tightening the thumbscrews. Note • Refer to “Computer Compatibility Chart” on page 66 for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions not to work. • When connecting the projector to a com- puter in this way, select “RGB” for “Signal Type” on the OSD menu or press on the remote control. (See page 52.) • A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized SharpVision Service Center or Dealer. • Depending on the computer you are us- ing, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer operation manual for switch- ing the computer signal output settings. To INPUT 2 terminal Notebook computer To RGB output terminal RGB cable (commercially available) DVI to 15-pin D-sub adaptor (sold separately) Connecting the thumbscrew cables I Connect the thumbscrew cable making sure that it fits cor- rectly into the terminal. Then, firmly secure the connec- tors by tightening the screws on both sides of the plug. I Do not remove the ferrite core attached to the RGB cable. Ferrite core

puter with DIGITAL RGB output Terminal (DIGITAL INPUT) 1 Slide the “DIGITAL INPUT TYPE” switch on the back ter- minal board to “PC”. 2 Connect a DVI cable to the pro- jector. 3 Connect the above cable to the computer. • Secure the connectors by tightening the thumbscrews. Note • Select DIGITAL INPUT mode when con- necting to digital output terminal of the computer. (See page 31.) • Before switching the “DIGITAL INPUT TYPE” switch and connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the com- puter to be connected. After making all connections, turn on the projector and then the computer. • Be sure that the computer is the last de- vice to be turned on after all the connec- tions are made. “Plug and Play” function I This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy setup. I Before using the “Plug and Play” function, be sure to turn on the projector first and the con- nected computer last. Note • The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA DDC compatible computer. To DIGITAL INPUT terminal To DVI digital output terminal DVI cable (sold separately) Desktop computer DIGITAL INPUT TYPE switch Optional accessory DVI cable Type: AN-C3DV (9'10'' (3.0 m)) Connecting the Projector to Other Devices

-23 Controlling the Projector Using an RS-232C Cable When the RS-232C terminal on the projector is connected to a computer with an RS-232C cable (null modem, cross type, commercially available), the computer can be used to con- trol the projector and check the status of the projector. See page 65 for details. 1 Connect an RS-232C cable to the projector. 2 Connect the above cable to the computer. Note • Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer. • The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details. • Refer to “Computer Compatibility Chart” on page 66 for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions not to work. Controlling the Projector by a Computer Desktop computer To RS-232C terminal To RS-232C terminal RS-232C cable (commercially available)

ing or rotating the projector. • When lowering the projector, be careful not to get your fingers caught in the area be- tween the Swivel Stand and the projector. Note • When the height or direction of the pro- jector is adjusted, the image may become distorted (keystoned), depending on the relative positions of the projector and the screen. See page 33 for details on the keystone correction. Using the Swivel Stand You can adjust the angle and direction of the projected image by using the Swivel Stand. 1 Unlock the lever on the Swivel Stand. 2 Adjust the angle and direction of the projected image as you want by lifting up the projec- tor and rotating the projector on the Swivel Stand. 3 Lock the lever on the Swivel Stand. Removing the Swivel Stand 1 Lift the projector (2) with pressing the removing-stand button on the back of the pro- jector (1). Adjustable up to ±10° from the standard position. Adjustable up to ±25° from the standard position. Adjustable up to ±3° from the standard position. Swivel Stand LOCK/UNLOCK lever 1 2 Removing- stand button -24

-25 Attaching the Swivel Stand 1 Align the tabs on the front bot- tom of the projector (1). 2 While holding down the button (2), place the projector onto the Swivel Stand (3) to attach. 3 Press the projector down firmly to attach it to the Swivel Stand to make sure it is se- curely attached to the Swivel Stand. Focusing and Zooming The picture can be focused and zoomed in or out by using the Focus ring and the Zoom knob. 1 Rotate the Focus ring until the image on the screen comes into focus. 2 Slide the Zoom knob. The im- age can be adjusted to the de- sired size within the zoom range. Using the Lens Shift The picture can be adjusted within the shift range of the lens by rotating the lens shift dial on the top of the projector using your finger. 1 3 2 Focus ring Zoom knob Lens shift dial UP DOWN Projected Image

Setup • Refer to pages 33 and 34 about the function of Keystone correction and placement of projector using the correction. • Decide the placement of the projector referring to the figures on the table and the diagram below according to the size of your screen and input signal. Center of the screen (a) (b) (c) (d) (f) Placement range (e) ±10° (a) Maximum projection distance (b)Minimum projection distance (c) Horizontal placement range when projection distance is maximum. (d)Horizontal placement range when projection distance is minimum. (e) Vertical placement range when projection distance is maximum. ( f) Vertical placement range when projection distance is minimum. Note • The aspect ratio of the projected image shifts slightly when the lens shift is at a position other than the top position. • The aspect ratio of the projected image also shifts slightly when the “H Keystone” and “V Keystone” functions are adjusted simultaneously. • When adjusting “H Keystone” and “V Keystone” at the same time, the values of adjustable angles for each setting become smaller. • Keystone correction cannot be applied to On-screen Display. • When Keystone correction is applied, the resolution of image can be deteriorated to some extent. • There are errors of ±3% in the formulas below. 3 4 : Screen area : Picture area 9 16 : Picture area When using a wide screen (16:9) In case of displaying the 16:9 picture on the whole of the 16:9 screen. When using a normal screen (4:3) In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen. Screen size (16:9)(x) Projection distance and Keystone correction Maximum projection distance Minimum projection distance Diag. 200" 150" 133" 106" 100" 92" 84" 72" 60" 40" Projection distance (a) Composite, S-video 480I/P, 1080I 720P RGB Vertical placement range (e) Projection distance (b) Composite, S-video 480I/P, 1080I 720P RGB Vertical placement range (f) Horizontal Placement range (d) Horizontal Placement range (c) Screen size (4:3)(x) Projection distance and Keystone correction Maximum projection distance Minimum projection distance Diag. 200" 150" 100" 84" 72" 60" 40" Horizontal Placement range (c) Projection distance (a) Composite, S-video 480I/P, 1080I 720P RGB Vertical placement range (e) Projection distance (b) Composite, S-video 480I/P, 1080I 720P RGB Vertical placement range (f) Horizontal Placement range (d) (a) = (0.04849498x - 0.038639669) / 0.3048 x: Screen size (diag.) (b) =(0.040201488x - 0.038804856) / 0.3048 34' 6'' (10.5m) 25'10''(7.9m) 22'11''(7.0m) 18' 3'' (5.6m) 17' 2'' (5.2m) 15'10''(4.8m) 14' 5'' (4.4m) 12' 4'' (3.8m) 10' 3'' (3.1m) 6' 10''(2.1m) – 23' 9'' (7.2m) 15' 9'' (4.8m) 13' 3'' (4.0m) 11' 4'' (3.5m) 9' 5'' (2.9m) 6' 3'' (1.9m) – 7' 3'' (2.2m) 4' 7'' (1.4m) 3' 11''(1.2m) 3' 3'' (1.0m) 2' 7'' (0.8m) 1' 8'' (0.5m) – 8' 2'' (2.5m) 5' 3'' (1.6m) 4' 7'' (1.4m) 3' 11''(1.2m) 2' 11''(0.9m) 1' 4'' (0.4m) – 5' 11''(1.8m) 3' 11''(1.2m) 3' 3'' (1.0m) 2' 7'' (0.8m) 2' 4'' (0.7m) 1' 4'' (0.4m) – 3' 11''(1.2m) 2' 7'' (0.8m) 2' 4'' (0.7m) 1' 12''(0.6m) 1' 8'' (0.5m) ' 12''(0.3m) 26' 3'' (8.0m) 19' 8'' (6.0m) 13' 1'' (4.0m) 10'11''(3.3m) 9' 4'' (2.9m) 7' 9'' (2.4m) 5' 2'' (1.6m) 6' 11''(2.1m) 5' 3'' (1.6m) 3' 3'' (1.0m) 2' 11''(0.9m) 2' 4'' (0.7m) 1' 12''(0.6m) 1' 4'' (0.4m) 7' 7'' (2.3m) 5' 7'' (1.7m) 3' 7'' (1.1m) 2' 11''(0.9m) 2' 7'' (0.8m) 1' 12''(0.6m) 1' 4'' (0.4m) 5' 3'' (1.6m) 3' 11''(1.2m) 2' 7'' (0.8m) 1' 12''(0.6m) 1' 8'' (0.5m) 1' 4'' (0.4m) ' 12''(0.3m) 4' 7'' (1.4m) 3' 3'' (1.0m) 2' 4'' (0.7m) 1' 8'' (0.5m) 1' 8'' (0.5m) 1' 4'' (0.4m) ' 8'' (0.2m) 8' 2'' (2.5m) 6' 3'' (1.9m) 5' 7'' (1.7m) 4' 3'' (1.3m) 3' 11''(1.2m) 3' 7'' (1.1m) 3' 3'' (1.0m) 2' 11''(0.9m) 2' 4'' (0.7m) 1' 4'' (0.4m) 5' 11''(1.8m) 4' 3'' (1.3m) 3' 11''(1.2m) 2' 11''(0.9m) 2' 11''(0.9m) 2' 7'' (0.8m) 2' 4'' (0.7m) 1' 12''(0.6m) 1' 8'' (0.5m) ' 12''(0.3m) 4' 11''(1.5m) 3' 7'' (1.1m) 3' 3'' (1.0m) 2' 7'' (0.8m) 2' 4'' (0.7m) 2' 4'' (0.7m) 1' 12''(0.6m) 1' 8'' (0.5m) 1' 4'' (0.4m) ' 8'' (0.2m) 5' 11''(1.8m) 4' 3'' (1.3m) 3' 11''(1.2m) 2' 11''(0.9m) 2' 11''(0.9m) 2' 7'' (0.8m) 2' 4'' (0.7m) 1' 12''(0.6m) 1' 8'' (0.5m) ' 12''(0.3m) 8' 6'' (2.6m) 6' 7'' (2.0m) 5' 7'' (1.7m) 4' 7'' (1.4m) 4' 3'' (1.3m) 3' 11''(1.2m) 3' 7'' (1.1m) 2' 11''(0.9m) 2' 4'' (0.7m) 1' 8'' (0.5m) 7' 7'' (2.3m) 5' 7'' (1.7m) 4' 11''(1.5m) 3' 11''(1.2m) 3' 7'' (1.1m) 3' 3'' (1.0m) 2' 11''(0.9m) 2' 7'' (0.8m) 2' 4'' (0.7m) 1' 4'' (0.4m) 28' 7'' (8.7m) 21' 5'' (6.5m) 18'12''(5.8m) 15' 1'' (4.6m) 14' 3'' (4.3m) 13' 1'' (4.0m) 11'11''(3.6m) 10' 3'' (3.1m) 8' 6'' (2.6m) 5' 7'' (1.7m) 11'10''(3.6m) 8' 10''(2.7m) 7' 10''(2.4m) 6' 3'' (1.9m) 5' 11''(1.8m) 5' 3'' (1.6m) 4' 11''(1.5m) 4' 3'' (1.3m) 3' 3'' (1.0m) 2' 4'' (0.7m) 10' 6'' (3.2m) 7' 10''(2.4m) 6' 11''(2.1m) 5' 7'' (1.7m) 5' 3'' (1.6m) 4' 7'' (1.4m) 4' 3'' (1.3m) 3' 7'' (1.1m) 2' 11''(0.9m) 1' 12''(0.6m) (a) = (0.052833802x - 0.038639669) / 0.3048 x: Screen size (diag.) (b) =(0.043798292x - 0.038804856) / 0.3048

-27 90° 90° 90° 90° Upper and Lower Lens Shift Position • This projector is equipped with a lens shift function that lets you adjust the projection height. • Adjust the projection height to match the setup configuration. • The screen can be moved maximum the length of one screen vertically using the lens shift. Note • Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. Tilting or angling the projector will reduce the effectiveness of the lens shift function. Screen size: 100 inches (254 cm) Aspect ratio: 16:9 Screen Upper and Lower Lens Shift Position (Ceiling Mount) When the projector is in the inverted position, use the upper edge of the screen as the base line, and exchange the lower and upper lens shift values. Screen Lower lens shift position (High mount setup) Upper lens shift position (Desktop setup) Lens center Lens center Screen size: 100 inches (254 cm) Aspect ratio: 16:9 Lower edge of screen (White portion) = Standard (0) point

dience. I Use the projector’s menu screen to reverse the projected im- age. (See page 56 for use of this func- tion.) Note • Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all feet flat and lev- eled. Projection using a mirror I Place a mirror (normal flat type) in front of the lens. Info • When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of the audience. Ceiling-mount setup I It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. I Before mounting the projector, remove the Swivel Stand. (See pages 24 and 25 for removing and attaching the Swivel Stand.) I Before mounting the projector, contact your nearest Authorized SharpVision Service Center or Dealer to obtain the recommended ceiling-mount bracket (sold separately). (AN-CM260 ceiling-mount bracket, AN- EP101B extension tube for AN-CM260.) I When the projector is in the inverted position, use the upper edge of the screen as the base line. I Use the projector’s menu screen to select the appropriate pro- jection mode. (See page 56 for use of this function.) When using the default setting. MOn-screen Display Image Projection The image is reversed. When using the default setting. MOn-screen Display The image is inverted. Setup

the projector before operating the following procedures. Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language ac- cording to the procedure on page 31. 1 Plug the power cord into the wall outlet. • The POWER indicator illuminates red, and the projector enters standby mode. 2 Press on the remote control or on the projector. • The blinking green LAMP indicator shows that the lamp is warming up. Wait until the indicator stops blinking before operating the projector. • If the power is turned off and then im- mediately turned on again, it may take a short while before the lamp turns on. Note • After the projector is unpacked and turned on for the first time, a slight odor may be emitted from the exhaust ventilative holes. This odor will soon disappear with use. When the power is on, the LAMP in- dicator illuminates, indicating the sta- tus of the lamp. Green: Lamp is ready. Green blinking: Warming up. / Cooling down. Red: Change the lamp.

on the projector to select the IN- PUT mode. • After pressing once on the projector, use to select the desired input mode. Note • When no signal is received, “NO SIG- NAL” will be displayed. When a sig- nal that the projector is not preset to receive is received, “NOT REG.” will be displayed. About the INPUT modes Used for projecting im- ages from equipment connected to INPUT 1 terminals. Used for projecting im- ages from equipment connected to INPUT 2 terminal. Used for projecting im- ages from equipment connected to INPUT 3 terminal. Used for projecting im- ages from equipment connected to INPUT 4 terminal. Used for projecting im- ages from equipment connected to DIGITAL INPUT terminal. INPUT 1 (Compo- nent) INPUT 2 (Compo- nent/RGB) INPUT 3 (S-Video) INPUT 4 (Video) DIGITAL On-screen Display Selecting the On- screen Display Lan- guage English is the preset language for the On- screen Display; however, this can be changed to German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese. Display the “Language” menu and se- lect the desired Language. ➝For operating the menu screen, see pages 38 to 41. INPUT 1 Mode INPUT 2 Mode INPUT 3 Mode INPUT 4 Mode DIGITAL INPUT Mode "On-screen Display (Example)

1 Press on the remote con- trol or on the projector, then press or again while the confirmation message is displayed, to put the projec- tor into the standby mode. • A dimly-lit screen is displayed for a short time to reduce lamp damage. Note • If you accidentally pressed and do not want to put the projector into the standby mode, wait until the confirmation message disappears. 2 Unplug the power cord from the AC outlet after the cooling fan stops. Info • Do not unplug the power cord dur- ing projection or cooling fan opera- tion. This can cause damage due to the rise in internal temperature, as the cooling fan also stops. • When connected to equipment such as an amplifier, be sure to turn off the power to the equipment con- nected first and then to the projec- tor. Image Projection STANDBY button STANDBY button

Vertical Keystone Correction KEYSTONE button ", ',\, | buttons KEYSTONE button ", ',\, | buttons Description Horizontally adjusts the keystone settings. Vertically adjusts the keystone settings. V and H Keystone adjustments are returned to the factory preset settings. Selected Item H Keystone V Keystone Reset Keystone Correction This function can be used to adjust the Key- stone settings. Note • For details about using the menu screen, see pages 38 to 41. 1 Press on the projector or on the remote control. 2 Press / to select “H Key- stone” or “V Keystone”. 3 Press / to move the mark on the selected adjustment item to the desired setting. Note • Straight lines and the edges of the displayed image may appear jagged, when adjusting the Key- stone setting. • When adjusting “H Keystone” and “V Keystone” at the same time, the values of adjustable angles for each setting become smaller. • The adjustable value of the “V Key- stone” becomes extremely small when “H Keystone” is made to be the maximum value. • Keystone correction is disabled while the picture mode is set to “SMART STRETCH”. (See page 35.) 4 To return to the normal screen, press again.

jected Image Using the Keystone Correction Place the projector at a distance from the screen that allows images to be projected onto the screen by referring to “Adjusting the Pro- jection Distance” on pages 26 and 27. 1 Project the test pattern of the Keystone correction function onto the screen. Rotate the Fo- cus ring until the image on the screen comes into focus. (See page 25.) 2 Change the projection angle using the Swivel Stand to prop- erly project images onto the screen. (See page 24). 3 Align the edge of the screen closest to the projector with the test pattern by adjusting the zoom and the Swivel Stand. (See pages 24 and 25.) 4 Adjust the Keystone function so that the size of the projected image matches the screen size. (See page 33.) 5 Align the image on the screen by adjusting the zoom function and the Swivel Stand. 6 Adjust the focus so that the projected image is in focus at the center of the screen. (See page 25.) Note • The aspect ratio of the projected image shifts slightly when the lens shift is at a position other than the top position. • The aspect ratio of the projected image also shifts slightly when the “H Keystone” and “V Keystone” functions are adjusted simultaneously. : Screen area Image Projection -34

Image You can instantly freeze a moving image with the remote control. 1 Press . • The projected image is frozen. 2 Press again to return to the moving image from the cur- rently connected device. Adjusting the Picture Aspect Ratio This function allows you to modify or custom- ize the picture display mode to enhance the input image. Depending on the input signal, you can choose SIDE BAR, SMART STRETCH, CINEMA ZOOM or STRETCH image. Press . Each time is pressed, the picture mode changes as shown on the next page. FREEZE button RESIZE button RESIZE button

1024
576 480I 480P 576I 576P NTSC PAL SECAM VGA SVGA XGA 768
576 1024
576 480P – – 720P – – 1024
576 1024
576 1024
576 SIDE BAR STRETCH CINEMA ZOOM SMART STRETCH 1024
576 – – 1024
576 1024
576 1080I For 4:3 aspect ratio For 16:9 aspect ratio • “STRETCH” is fixed when 540P, 720P or 1080I signal is entered. • “SMART STRETCH” cannot be selected while input signal from a computer (VGA, SVGA or XGA) is entered. 480I 480P 576I 576P NTSC PAL SECAM 540P 1080I 720P VGA SVGA XGA Input Signal SIDE BAR SMART STRETCH Output screen image STRETCH CINEMA ZOOM 4:3 aspect ratio Letterbox 16:9 aspect ratio Squeeze 4:3 aspect ratio Note • “SMART STRETCH” cannot be selected while the Keystone correction (page 33) is being adjusted. • Keystone correction (page 33) is disabled while the picture mode is set to “SMART STRETCH”. • 580I/580P is displayed on the screen when signal 576I/576P is input. Image Projection

The menu screens allow you to adjust the image and various projector settings. The menu can be operated to achieve two functions, adjustment and setting. (For adjusting the menu items, see pages 38 and 39. For setting the menu items, see pages 40 and 41.) Menu screen (example) Menu Selections (Adjustments) 1 Press . • The menu screen is displayed. Note • The “Picture” menu screen for the selected input mode is displayed. -38 ENTER button UNDO button MENU button ", ', \, | buttons ENTER button UNDO button MENU button ", ', \, | buttons

Select the menu icon. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode 2 Press \ \\ \\ or | || || to display the other menu screens. • The menu icon for the selected menu screen is highlighted. Note • The “Fine Sync” menu is not avail- able for INPUT 3 or 4. • For items on the menus, see the tree charts on pages 42 and 43. 3 Press " " " " " or ' ' ' ' ' to select the item you want to adjust. Note • To display a single adjustment item, press after selecting the item. Only the menu bar and the selected adjustment item will be displayed. Then if you press " or ', the fol- lowing item (“Bright” after “Con- trast”) will be displayed. • Press to return to the previous screen. 4 Press \ \\ \\ or | || || to adjust the item selected. • The adjustment is stored. 5 Press . • The menu screen will disappear. Adjust the item. Select the item.

Note • The “Picture” menu screen for the selected input mode is displayed. 2 Press \ \\ \\ or | || || to display the other menu screens. • The menu icon for the selected menu screen is highlighted. Note • The “Fine Sync” menu is not avail- able for INPUT 3 or 4. • For items on the menus, see the tree charts on pages 42 and 43. -40 Using the Menu Screen ENTER button UNDO button MENU button ", ', \, | buttons ENTER button UNDO button MENU button ", ', \, | buttons Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Select the menu icon.

3 Press " " " " " or ' ' ' ' ' to select the item you want to set. Note • Press to return to the previous screen. • In some menus, select the icon us- ing “ ”. 4 Press | || ||. • The sub menu is displayed. 5 Press " " " " " or ' ' ' ' ' to select the set- ting of the item displayed in the sub menu. 6 Press . • The item selected is set. 7 Press . • The menu screen will disappear. Sub menu Select the item. Sub menu

Language ( ) English Deutsch Español Nederlands Français Italiano Svenska Português Front CeilingFront Rear CeilingRear Picture ( ) Tint 30 30 Color 30 30 Sharp 30 30 Contrast 30 30 Bright 30 30 Red 30 30 Blue 30 30 Reset 5500K 6500K 8500K 9300K 10500K Standard Cinema 1 Cinema 2 Memory 2 Memory 3 Memory 4 Memory 5 Memory OFF Cinema 3 7500K CLR Temp Gamma White Emphasis [ON/OFF] Picture Setting Memory 1 Fine Sync ( ) Auto Sync [ON/OFF] Clock 30 30 30 30 30 30 Phase 15 15 H-Pos V-Pos Reset Special Modes Signal Info Resolution Hor Freq Vert Freq 640
480 37.5 kHz 72 Hz 640
480 720
480 480P RGB Background [None/Blue] Options ( ) Component Auto Power Off [ON/OFF] Menu Position Menu Color [Opaque/Translucent] Center Lamp Timer (Life) OSD Display [ON/OFF] Signal Type Upper Right Lower Right Upper Left Lower Left Eco Mode [Eco/Standard] PRJ Mode ( ) 10 0 10 0 10 0 10 0 10 0 10 0 I INPUT 1 / 2 / DIGITAL INPUT Mode Main menu Sub menu Main menu Note • The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only. • “Color”, “Tint”, and “Sharp” do not appear when “RGB” is selected in INPUT 2 mode. • “Signal Type” is not displayed when using INPUT 1. • “Color”, “Tint”, “Sharp”, “Clock”, “Phase”, “H- Pos”, “V-Pos”, “Special Modes” and “Auto Sync” cannot be used in the DIGITAL INPUT mode. • “Clock”, “Phase” and “Auto Sync” cannot be used in the Component mode.

Lamp Timer (Life) Picture ( ) Tint 30 30 30 30 Color 30 30 Sharp Contrast 30 30 Bright 30 30 Red 30 30 Blue 30 30 Reset 5500K 3D Progressive 6500K 3D Progressive 3D Progressive 8500K 3D Progressive 9300K 3D Progressive 10500K 3D Progressive Standard 3D Progressive Cinema 1 3D Progressive Cinema 2 3D Progressive Memory 2 3D Progressive Memory 3 3D Progressive Memory 4 3D Progressive Memory 5 Auto 3D ProgrOFFessive Memory OFF 3D Progressive Cinema 3 Background [None/Blue] Options ( ) PAL NTSC3.58 NTSC4.43 PAL–M PAL–60 SECAM Language ( ) English Deutsch Español Nederlands Français Italiano Svenska Português Auto Power Off [ON/OFF] Menu Position Menu Color [Opaque/Translucent] Center PRJ Mode ( ) Front CeilingFront Rear CeilingRear 7500K CLR Temp Gamma White Emphasis [ON/OFF] Picture Setting 3D Progressive Memory 1 OSD Display [ON/OFF] Video System PAL–N Upper Right Lower Right Upper Left Lower Left Eco Mode [Eco/Standard] 10 0 10 0 10 0 10 0 10 0 10 0 Note • “Tint” cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60. I INPUT 3 / 4 Mode Main menu Sub menu Main menu

tings. Adjusting the Picture Adjusting Image Prefer- ences Note • First select “Memory 1-5” or “Memory OFF” when you want to save the “Picture” menu settings. See page 47 for details. Adjust the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. On-screen Display Note • “Color”, “Tint” and “Sharp” do not appear for RGB input in INPUT 2 mode. • To reset all adjustment items, select “Re- set” on the “Picture” menu screen and press . • “Tint” cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60. • “Color”, “Tint” and “Sharp” cannot be used in the DIGITAL INPUT mode. -44 Contrast Bright Color Tint Sharp Red Blue For adjusting the contrast level For adjusting the brightness of an image For adjusting the color intensity of an image For adjusting the tones of an image For making sharper or softer the contour of an image For adjusting the redness of an image For adjusting the blueness of an image For less contrast For less brightness For less color intensity Skin tones become purplish For less sharpness For weaker red For weaker blue For more contrast For more brightness For more color intensity Skin tones become greenish For more sharpness For stronger red For stronger blue Selected Item Description \ button | button

Adjusting the Color Temperature This function allows for selecting the desired color temperature. With the lower value se- lected, the projected image becomes warmer, reddish and incandescent-like while with the higher value, the image becomes cooler, blu- ish and fluorescent-like. Select “CLR Temp” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. On-screen Display 5500K 6500K 7500K 8500K 9300K 10500K Selected Item Description The less the value is set to, the warmer, reddish, incandescent-like the image becomes. The more the value is set to, the cooler, bluish, fluorescent-like the image becomes. “CLR Temp” is fine adjusted by following the procedure below. 1 Select “CLR Temp” in the “Pic- ture” menu on the menu screen and press . • A single menu bar of “CLR Temp” is displayed. 2 Press ' ' ' ' ' or " " " " " to fine adjust the color temperature. • With the lower value selected, the pro- jected image becomes magenta- tinged. With the higher value selected, the projected image becomes green- tinged. • Pressing \ or | changes the value of the color temperature in the sub menu. Note •Values on “CLR Temp” are only for gen- eral standard purposes.

function. Four gamma settings are available to allow for differences in the brightness of the room. Select “Gamma” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Adjusting the Picture On-screen Display -46 Emphasizing the Con- trast This function emphasizes the bright portions of images to obtain a higher contrast image. Select “White Emphasis” in the “Pic- ture” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. On-screen Display Standard Cinema 1 Cinema 2 Cinema 3 Selected Item Description Standard picture without gamma correction Gives greater depth to darker portions of images. Brightness is toned down and the image becomes more balanced. Brighten the darker portions of images for easier viewing in a dimly lit room. (ON) (OFF) Selected Item Description For emphasizing the bright portions of images For disabling “White Emphasis”

Settings of all items in “Picture” can be stored for the respective input modes. The stored settings can be selected in any input modes. Besides “Memory 1” to “Memory 5”, other settings on the “Picture” menu can be stored for each input mode. The settings stored in “Memory OFF” cannot be applied when another input mode is selected. Memory 1-5 Memory OFF Selected Item Description On-screen Display PICTURE SETTING button PICTURE SETTING button Picture Setting Func- tion This function stores all items set in “Picture”. Five settings can be stored separately in “Memory 1” to “Memory 5”. Each stored set- ting is reassigned to each input mode (INPUT 1 to INPUT 4 and DIGITAL). Even when the input mode or signal is changed, you can easily select optimal set- tings from the stored settings. IStoring the Adjustment Val- ues for Each Memory Num- ber Select “Picture Setting” on the “Picture” menu and the memory location where you want to store the settings. Then adjust the setting items on the “Picture” menu. ➝For operating the menu screen, see pages 38 to 41. IApplying the Stored Settings If you want to apply the stored settings on the “Picture” menu, select “Picture Setting” on the “Picture” menu and the memory location where you have stored the settings. Note • This function can be operated using the on the projector or on the remote control, as well as the OSD menu screen. Each time or is pressed, the memory number changes as shown be- low. Memory 1 Memory 2 Memory 3 Memory OFF Memory 5 Memory 4

Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen. When Auto Sync is OFF When “Auto Sync” is “OFF”, interference such as flickering or vertical stripes may occur if displaying tilings or vertical stripes. Should this occur, adjust “Clock”, “Phase”, “H-Pos” and “V-Pos” for obtaining an optimum image. Select “Clock”, “Phase”, “H-Pos” or “V- Pos” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • “Clock”, “Phase”, “H-Pos” and “V-Pos” can- not be used in the DIGITAL INPUT mode. • “Clock” and “Phase” cannot be used in the Component mode. • Computer image adjustments can be made easily by pressing AUTO SYNC on the re- mote control. See page 50 for details. • To reset all adjustment items, select “Re- set” on the “Fine Sync” menu screen and press . • The adjustable area of each item may be changed according to the input signal. On-screen Display -48 Selected Item Description Clock Phase H-Pos V-Pos Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centers the on-screen image by moving it to the left or right. Centers the on-screen image by moving it up or down.

On-screen Display Special Modes Adjust- ment Ordinarily, the type of input signal is detected and the correct resolution mode is automati- cally selected. However, for some signals, the optimal resolution mode in “Special Modes” on the “Fine Sync” menu screen may need to be selected to match the computer display mode. Set the resolution by selecting “Special Modes” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.) • When inputting DTV 1080I signal, select the corresponding type of signal. • When inputting 720P signal from the video equipment, select “720P”. When inputting 1280 × 720 signal from the com- puter, select “HTPC”. • “Special Modes” cannot be used in the DIGITAL INPUT mode.

AUTO SYNC button On-screen Display (ON) (OFF) Selected Item Description Auto Sync adjustment will occur when the projector is turned on or when the input signals are switched, when connected to a computer. Auto Sync adjustment is not automatically performed. Auto Sync Adjustment Used to automatically adjust a computer im- age. Select whether the image is to be synchro- nized automatically when switching the sig- nal with “ON” or “OFF”. Select “Auto Sync” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 48.) • The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector. • “Auto Sync” cannot be used in the DIGI- TAL INPUT mode. • Auto Sync adjustment is also performed by pressing AUTO SYNC on the remote control. Checking the Input Signal This function allows you to check the current input signal information. Select “Signal Info” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • 540P is displayed on the screen when signal 1080I is inputted during DVI con- nection.

(ON) (OFF) Checking the Lamp Life Status You can confirm the cumulative lamp usage time and the remaining lamp life (percentage). Display the “Options” menu to check the lamp life status. ➝For operating the menu screen, see pages 38 to 41. Note • It is recommended that the lamp be changed when the remaining lamp life becomes 5%. For lamp replacement, contact your near- est Authorized SharpVision Service Cen- ter or Dealer. • The table above indicates rough estimates in the case of using only in each mode shown. Remaining lamp life changes within the range of the values shown depending on the frequency at which “Eco Mode” is switched to “ ” (Eco mode) and “ ” (Standard mode) (see page 53). Using the “Options” Menu On-screen Display On-screen Display All On-screen Displays are displayed. INPUT/FREEZE/AUTO SYNC/ “An invalid button has been pressed.” are not displayed. Selected Item Description Turning on/off the On- screen Display This function allows you to turn on or off the on-screen messages that appear during input select. Select “OSD Display” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Remaining lamp life 100% 5% Approx. Approx. 4,000 hours 200 hours Approx. Approx. 3,000 hours 150 hours Lamp usage condition Operated exclusively in Eco mode ( ) Operated exclusively in Standard mode ( )

-52 Selecting the Signal Type This function allows you to select the input signal type Component or RGB for INPUT 2. Select “Signal Type” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • “RGB” or “Component” can be selected with on the remote control only in INPUT 2. On-screen Display Setting the Video Signal (VIDEO menu only) The video input system mode is preset to “Auto”; however, it can be changed to a spe- cific system mode if the selected system mode is not compatible with the connected audiovi- sual equipment. Select “Video System” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • When the system mode is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal. • “Auto” cannot be set for PAL-M and PAL- N input signals. Select “PAL-M” or “PAL- N” in “Video System” menu for PAL-M and PAL-N input signals. On-screen Display Set when RGB signals are received. Set when Component signals are received. RGB Component Selected Item Description RGB/COMP. button

Selecting a Background Image This function allows you to select the image displayed when no signal is being sent to the projector. Select “Background” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Blue screen Black screen (Blue) (None) Selected Item Description On-screen Display Setting the Eco Mode This function allows you to select the desired power consumption mode. Select “Eco Mode” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • Although lamp life and noise are improved when “Eco Mode” is set to “ ” (Eco mode), brightness decreases by 20%. • “Eco Mode” is factory preset to “ ” (Stan- dard mode). (Eco mode) (Standard mode) Brightness 80% 100% Power consumption 230 W 285 W Selected Item Lamp life Approx. 4,000 hours Approx. 3,000 hours On-screen Display

Selecting the Menu Screen Position This function allows you to select the desired position of the menu screen. Select “Menu Position” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. On-screen Display Center Upper Right Lower Right Upper Left Lower Left Selected Item The menu is displayed on the center of the image. The menu is displayed on the upper right of the image. The menu is displayed on the lower right of the image. The menu is displayed on the upper left of the image. The menu is displayed on the lower left of the image. Description On-screen Display Automatic Power Shut- off Function When no input signal is detected for more than 15 minutes, the projector will automatically en- ter the standby mode if set to “ ” (ON). Select “Auto Power Off” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. Note • “Auto Power Off” is factory preset to “ ”. • When the Auto Power Off function is set to “ (ON)”, 5 minutes before the projector enters the standby mode, the message “En- ter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes. Selected Item Description Projector automatically enters the standby mode after 15 minutes without an input signal. Automatic Power Shut-off disabled.

Selecting the Menu Color This function allows you to select the color of the menu screen. Select “Menu Color” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 38 to 41. On-screen Display The menu is displayed opaquely. The menu is displayed translucently. The part of the menu on the image becomes transparent. (Opaque) (Translucent) Selected Item Description

This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications. Setting the Projection Mode Display the “PRJ Mode” menu and se- lect the desired projection mode. ➝For operating the menu screen, see pages 38 to 41. Note • This function is used for the reversed im- age and ceiling-mount setups. See page 28 for these setups. On-screen Display Normal image Inverted image Reversed image Reversed and inverted image Front CeilingFront Rear CeilingRear Selected Item Description

I If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below. TEMPERATURE WARNING indicator POWER indicator LAMP indicator TEMP. LAMP POWER About the temperature warning indicator If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, “ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and then the projector will enter the standby mode. After “ ” appears, be sure to perform the following measures. About the lamp indicator I The lamp life becomes 0%, when used for approximately 4,000 hours with “Eco mode” or when used for approximately 3,000 hours with “Standard mode” (see page 53). I When the remaining lamp life becomes 5% or less, “ ” (yellow) will be displayed on the screen. When the percentage be- comes 0%, “ ” will change to “ ” (red), the lamp will automatically turn off and then the projector will automatically en- ter the standby mode. At this time, the lamp indicator will illuminate in red. I If you try to turn on the projector a fourth time without replacing the lamp, the pro- jector will not turn on. Maintenance indicator Condition Problem Possible Solution Temperature warning indicator Normal Abnormal Off Red on/ Standby The internal temperature is abnormally high. Abnormal • Blocked air intake • Relocate the projector to an area with proper ventilation. • Cooling fan break- down • Internal circuit failure • Clogged air intake • Take the projector to your nearest Authorized SharpVision Service Center or Dealer for repair. Lamp indicator Red on/ Standby The lamp does not illuminate. • Burnt-out lamp • Lamp circuit failure • Carefully replace the lamp. (See page 59.) • Take the projector to your nearest Authorized SharpVision Service Center or Dealer for repair. • Please exercise care when replacing the lamp. Red on Time to change the lamp. • Remaining lamp life becomes 5% or less. Power indicator The power is not turned on. • The lamp unit cover is open. • Securely install the cover. • If the power is not turned on even when the lamp unit cover is securely installed, contact your nearest Authorized SharpVision Service Center or Dealer for advice. Green on/ Red on Off Green on Green blinks when the lamp is warming up.

Info • If the temperature warning indicator illuminates, and the projector enters the standby mode, follow the pos- sible solutions on the previous page and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.) • If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. • If you want to clean the air vents during projector operation, be sure to put the projector into the standby mode. After the cooling fan has stopped, clean the vents. • The cooling fan keeps the internal temperatures of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction. • Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds. Lamp I It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be- comes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 51. I For lamp replacement, please consult your nearest Authorized SharpVision Service Center or Dealer. IMPORTANT NOTE TO U.S. CUSTOMERS: The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho- rized Projector Dealer or Service Center. For the name of the nearest Authorized SharpVision Service Center or Dealer, please call toll-free: 1-888-GO-SHARP (1-888-467-4277). U.S.A. ONLY Caution Concerning the Lamp I This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. I When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. I Should the lamp break, the glass particles may spread inside the lamp unit or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible. I Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Authorized SharpVision Service Center or Dealer to remove the damaged lamp and assure safe operation. Replacing the Lamp Caution • Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching it can lead to burn or injury. • Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit. I If the new lamp does not light after replacement, take your projector to the nearest Authorized SharpVision Service Center or Dealer for repair. Purchase a replacement lamp unit of type BQC- XVZ200++1 from your nearest Authorized SharpVision Service Center or Dealer. Then carefully change the lamp by following the instructions described in this section. If you wish, you may have the lamp replaced at your nearest Authorized SharpVision Service Center or Dealer.

ing the Lamp Unit Caution • Be sure to remove the lamp unit by the handle. Do not touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, carefully follow the steps below. • Replace the lamp after turning off the power and unplugging the power cord. 1 Put the projector into the standby mode. • Press . • Wait until the cooling fan stops. 2 Unplug the power cord. • Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). 3 Remove the Swivel Stand. (See page 24.) 4 Remove the lamp unit cover. • Loosen the user service screw that se- cures the lamp unit cover. • Slide the lamp unit cover in the direc- tion of the arrow. 5 Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. User service screw -60 Regarding the Lamp STANDBY button Power cord

• Press the lamp unit firmly into the lamp unit compartment. Fasten the secur- ing screws. 7 Attach the lamp unit cover. • Slide the lamp unit cover in the direc- tion of the arrow. • Fasten the user service screw. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. 1 Plug the power cord. • Confirm that the POWER indicator illuminates red. 2 Reset the lamp timer. • Press , , , , and in order. Then press . • “LAMP 0000H” is displayed on the screen. Info • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, the lamp may become damaged or explode. Power cord ON button UNDO button INPUT button ENTER button

• This projector is equipped with ventilative holes to ensure the opti- mal operating condition of the projec- tor. • Periodically clean the ventilative hole by vacuuming it off with a vacuum cleaner. • The ventilative holes should be cleaned every 100 hours of use. Clean the ventilative holes more often when the projector is used in a dirty or smoky location. Cleaning the Ventilative Holes 1 Put the projector into the standby mode. • Press . • Wait until the cooling fan stops. 2 Unplug the power cord. 3 Clean the dust off by putting the cleaner hose on the intake ventilative holes. Side and Rear view Bottom view Intake ventilative holes Intake ventilative holes Intake ventilative holes Swivel stand Cleaner hose -62 STANDBY button Power cord

•Selected input is wrong. (See page 31.) •Cables incorrectly connected to back panel of the projector. (See pages 14–23.) •“Contrast” and “Bright” adjustments are set to minimum position. (See page 44.) •Picture adjustments are not correct. (See page 44.) •Adjust the focus. (See page 25.) •Projection distance is too long or too short to allow for proper focus. (See pages 26 and 27.) •OSD Display is set to “OFF”, preventing to display some or all On-screen Displays. (See page 51.) •If the picture is normal, the sound is due to cabinet shrinkage caused by temperature changes. This will not affect operation or performance of the projector. •Refer to “Maintenance Indicators” on page 58. •Adjust the “Phase” setting. (See page 48.) •Change the input signal type. (See page 52.) If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on this page. If this operation manual does not answer your ques- tion, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an e-mail at [email protected] . Our World Wide Web address is http://www.sharpusa.com/ . Problem No picture appears. Color is faded or poor. Picture is blurred. No OSD appears. An unusual sound is occasionally heard from the cabinet. Maintenance indicator illuminates. Picture noise appears. Image is green on INPUT 2 Component. Image is pink (no green) on INPUT 2 RGB. Kensington Security Standard connector This projector has a Kensington Secu- rity Standard connector for use with a Kensington MicroSaver Security Sys- tem. Refer to the information that came with the system for instructions on how to use it to secure the projector. Rear View Using the Kensington Lock Troubleshooting For SHARP Assistance (U.S.A. only)

RS-232C Port: 9-pin D-sub male connector Pin No. Signal Name I/O Reference 1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Reserved Connected to internal circuit 5 SG Signal Ground Connected to internal circuit 6 Reserved Connected to internal circuit 7 Reserved Connected to internal circuit 8 Reserved Connected to internal circuit 9 Not connected DVI-I (INPUT 2 / DIGITAL INPUT) port : 29 pin connector • DVI Digital INPUT Pin No. Signal Pin No. Signal 1 T.M.D.S data 2– 16 Hot plug detection 2 T.M.D.S data 2+ 17 T.M.D.S data 0– 3 T.M.D.S data 2 shield 18 T.M.D.S data 0+ 4 Not connected 19 T.M.D.S data 0 shield 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 T.M.D.S clock shield 8 Not connected 23 T.M.D.S clock+ 9 T.M.D.S data 1– 24 T.M.D.S clock– 10 T.M.D.S data 1+ C1 Not connected 11 T.M.D.S data 1 shield C2 Not connected 12 Not connected C3 Not connected 13 Not connected C4 Not connected 14 +5V power C5 Ground 15 Ground • DVI Analog RGB Input Pin No. Signal Pin No. Signal 1 Not connected 16 Hot plug detection 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 Not connected 8 Vertical sync 23 Not connected 9 Not connected 24 Not connected 10 Not connected C1 Analog input Red 11 Not connected C2 Analog input Green 12 Not connected C3 Analog input Blue 13 Not connected C4 Horizontal sync 14 +5V power C5 Ground 15 Ground • DVI Analog Component Input Pin No. Signal Pin No. Signal 1 Not connected 16 Not connected 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 Not connected 21 Not connected 7 Not connected 22 Not connected 8 Not connected 23 Not connected 9 Not connected 24 Not connected 10 Not connected C1 Analog input Pr/Cr 11 Not connected C2 Analog input Y 12 Not connected C3 Analog input Pb/Cb 13 Not connected C4 Not connected 14 Not connected C5 Ground 15 Ground 17 • • • • • • • • • ~ • • • • • • • • • • • • • ~ • • • • • • • • ~ • • • • 24 18 23 C3 2 1 9 16 C1 C2 C4 C5 8 7 6 7 8 9 1 2 3 4 5

commercially available) to the projector. (See page 23 for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Baud rate: 9,600 bps Data length: 8 bits Parity bit: None Stop bit: 1 bit Flow control: None Basic format Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer. Info • When more than one code is being sent, send each command only after the OK response code for the previous command from the projector is verified. Note • When using the computer control function of the projector, the projector’s operating status cannot be read by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with the on-screen display. Commands Example: • When power on. Response code format Normal response Problem response (communication error or incorrect command) Command format (RS-232C) Specifications and Command Settings → ← P O W R _ 1 _ _ O K Projector Computer Return code (0DH) C1 C2 C3 C4 P1 P2 P3 P4 Command 4-digit Parameter 4-digit O K Return code (0DH) E R R Return code (0DH) Note • If an underbar (_) appears in the parameter column, enter a space. CONTROL CONTENTS POWER ON STANDBY INPUT 1 (COMPONENT 1) INPUT 2 (COMPONENT 2) INPUT 3 (S-VIDEO) INPUT 4 (VIDEO) DIGITAL INPUT MODE OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR P P I I I I I O O V V V V V W W E E E E E R R D D D D D _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1 0 1 2 3 4 5 BUTTONS & REMOTE CONTROL BUTTONS COMMAND PARAMETER RETURN

Note • This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s opera- tion manual. Horizontal Frequency: 15–70 kHz Vertical Frequency: 43–75 Hz Pixel Clock: 12–80 MHz Compatible with sync on green XGA compatible in intelligent compression PC/ MAC/ WS Horizontal Frequency (kHz) Vertical Frequency (Hz) VGA PC SVGA XGA VESA Standard DVI Support ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Resolution 640
350 720
350 640
400 720
400 640
480 800
600 1,024
768 Display Upscale Intelligent Compression 27.0 60 27.0 60 27.0 60 60 31.5 70 31.5 70 31.5 70 31.5 60 34.7 70 37.9 72 37.5 75 31.4 50 35.1 56 37.9 60 44.5 70 48.1 72 46.9 75 ✔ 31.5 70 27.0 26.2 50 35.5 43 40.3 50 58.1 72 56.5 70 1,280
720 — 45.0 60 MAC 16" PC/ MAC 13" PC/ MAC 19" 640
480 832
624 Intelligent Compression 34.9 67 60.0 1,024
768 VGA SVGA ✔ ✔ XGA 48.4 60 75 46.8 75 49.6 75 Upscale

tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit. If you have any questions about this matter, please call toll free 1-877-DTV-SHARP (1-877-388- 7427). U.S.A. ONLY Specifications Product type Model Video system Display method DLP panel Lens Projection lamp Video input signal S-video input signal Component input signal (INPUT 1) Component input signal (INPUT 2) Horizontal resolution RGB input signal Pixel clock Vertical frequency Horizontal frequency Computer control signal Rated voltage Input current Rated frequency Power consumption Heat dissipation Operating temperature Storage temperature Cabinet I/R carrier frequency Dimensions (approx.) Weight (approx.) Supplied accessories Replacement parts Projector XV-Z200U PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43 DTV 480I/480P/720P/1080I DLP chip, RGB optical shutter method Panel size: 0.6 Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments Drive method: Digital Light Processing (DLP™) No. of dots: 589,824 dots (1,024 [H]
576 [V]) 1–1.2
zoom lens, F1.75–2.04 f=28.0–33.5 mm 210 W/168 W SHP lamp RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω terminated 4-pin Mini DIN connector (INPUT 3) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated RCA Connector Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB: 0.7 Vp-p, 75 Ω terminated PR: 0.7 Vp-p, 75 Ω terminated 29-pin connector DVI input signal: Digital 250–1,000 mV 50 Ω Analog 0.7 Vp-p 75 Ω Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB: 0.7 Vp-p, 75 Ω terminated PR: 0.7 Vp-p, 75 Ω terminated 520 TV lines (NTSC 3.58 input) DVI-I terminal Input impedance 50 Ω Input level 250-1000 mV Input impedance 75 Ω Input level 0.7 Vp-p • Separate sync/Composite sync Input level TTL level Input impedance 1 KΩ • Green on sync Input level (Synchronizing input) 0.286 Vp-p Input impedance 75 Ω 12–80 MHz 43–75 Hz 15–70 kHz 9-pin D-sub connector (RS-232C Port) AC 100–240 V 3.2 A 50/60 Hz 285 W 1,070 BTU/hour 41°F to 95°F (5°C to 35°C) 4°F to 140°F (20°C to 60°C) Plastic 38 kHz 141⁄2 (W)
69⁄16 (H)
127⁄8 (D) (368
153.8
327 mm) (including swivel stand) 141⁄2 (W)
45⁄8 (H)
127⁄8 (D) (368
118
327 mm) (main body only) 10.1 lbs. (4.6 kg) (including swivel stand) 9.0 lbs. (4.1 kg) (main body only) Remote control, Two AA size batteries, Power cord, Terminal cover, Lens cap (attached on the body), Operation manual, Screws for terminal cover Lamp unit (Lamp/cage module) (BQC-XVZ200++1), Remote control (RRMCGA218WJSA), AA size batteries, Power cord (QACCDA007WJPZ), Terminal cover (GCOVAA116WJKB), Lens cap (CCAPHA004WJ01), Operation manual (TINS- B005WJZZ), Screws for terminal cover (XBBSN40P10000) This SHARP projector uses a DMD chip. This very sophisticated chip contains 589,824 pixels. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. Specifications are subject to change without notice.

6 9/16 (153.8) 4 5/8 (118) 14 1/2 (368) Front View Bottom View Side View Top View Side View Rear View Dimensions Units: inches (mm)

aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9. Auto Sync Optimizes projected computer images by auto- matically adjusting certain characteristics. Background Initial setting image projected when no signal is being output. Clock Clock adjustment is used to adjust vertical noise when clock level is incorrect. CLR Temp (Color temperature) Function that can be used to adjust the color tem- perature to suit the type of image input to the pro- jector. Decrease the color temperature to create warmer, reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture. Composite sync Signal combining horizontal and vertical sync pulses. Digital keystone correction Function to digitally correct a distorted image when the projector is set up at an angle, smoothes out jaggies on keystone images and compresses the image not only horizontally but vertically keeping the 16 : 9 aspect ratio. DVI (Digital Visual Interface) Display digital interface that also supports analog interfaces. Gamma Image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. You can select from four differ- ent modes: Standard, Cinema 1, Cinema 2 and Cinema 3. Intelligent compression and expansion High quality resizing of lower and higher resolu- tion images to fit the projector’s native resolution. Phase Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal flicker. Resize Allows you to modify or customize the picture dis- play mode to enhance the input image. You can select from four different modes: SIDE BAR, SMART STRETCH, CINEMA ZOOM and STRETCH. RS-232C Function to control the projector from the com- puter by using the RS-232C ports on the projec- tor and computer. Stretch Mode that stretches the 4:3 image horizontally to display it on the wide screen. Sync on green Video signal mode of a computer which overlaps horizontal and vertical sync signal to green color signal pin.

Adjusting the Picture ............................................ 44 ADJUSTMENT buttons ........................................ 39 Aspect ratio .......................................................... 35 Automatic power shut-off function ........................ 54 Auto sync adjustment ........................................... 50 AUTO SYNC button ............................................. 50 B Background .......................................................... 53 C Ceiling-mount ....................................................... 28 Ceiling+Rear ........................................................ 56 Clock .................................................................... 48 COMPONENT terminals ...................................... 17 D DIGITAL INPUT terminal ...................................... 20 DVI ....................................................................... 20 E Eco mode ............................................................. 53 ENTER button ...................................................... 39 Exhaust ventilative hole ......................................... 6 F Focus ring ............................................................ 25 FREEZE button .................................................... 35 I INPUT buttons...................................................... 31 K Kensington Lock .................................................. 63 KEYSTONE button ............................................... 33 L LAMP indicator ..................................................... 58 Lens shift .............................................................. 25 M MENU button........................................................ 38 O ON button ............................................................. 30 On-screen display ................................................ 51 On-screen display language ................................ 31 P Phase ................................................................... 48 Power cord ........................................................... 14 POWER indicator ................................................. 30 R Rear projection ..................................................... 28 Remote control ..................................................... 10 Remote control sensor ......................................... 11 Remote control signal transmitter ........................ 10 RESIZE button ..................................................... 35 RS-232C terminal ................................................ 23 S STANDBY button ................................................. 32 STRETCH ............................................................ 35 S-VIDEO INPUT terminal ..................................... 15 Sync on green ...................................................... 66 T TEMPERATURE WARNING indicator ................. 58 U UNDO button........................................................ 39 V VIDEO INPUT terminal ........................................ 16 Video System ....................................................... 52 Z Zoom knob ........................................................... 25

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer. The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Model Specific Section (In-Home Service) Your Product Model Number & Description: Warranty Period for this Product: Additional Item(s) Excluded from Warranty Coverage (if any): Where to Obtain Service: What to do to Obtain Service: XV-Z200U Projector (Be sure to have this information available when you need service for your Product.) One (1) year parts and labor from date of purchase except for the Projector Lamp for which the warranty period is ninety (90) days from date of purchase. After the ninety (90) day warranty period on the Projector Lamp, parts and labor for a lamp replacement are the responsibility of the consumer. Cleaning of Optical System and/or replacement of any filter. Labor & materials required to remove and reinstall a suspended projector in installations not accessible with a standard (8' step) ladder or ceilings exceeding 12’ in height. Labor & materials required to remove and reinstall a projector in complex systems including, but not limited to, projectors installed in custom enclosures, projectors connected to third party control and automation systems, and realignment of projectors installed in “mirrored” rear projection enclosures. From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP. Contact your Sharp Authorized Servicer to obtain in-home service for this Product. The Servicer will come to your home and if necessary to remove the Product for repair at the Servicer’s facility, the Servicer will reinstall it upon completion of repair. Be sure to have Proof of Purchase available. VALID IN USA ONLY TO OBTAIN PRODUCT INFORMATION, CALL 1-877-DTV-SHARP OR VISIT www.sharpusa.com.

Congratulations on your purchase! Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer: Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as specified herein. This warranty shall not apply to: (a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate use as outlined in the owner’s manual. (b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp’s Authorized Service Centres or Sharp’s Authorized Servicing Dealers. (c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to head cleaning tapes and chemical cleaning agents. (d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons, cables and paper. (e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear. (f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or liquid spillage. (g) Any product received without appropriate model, serial number and CSA/cUL markings. (h) Any products used for rental or commercial purposes. (i) Any installation, setup and/or programming charges. Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television with the screen size of 27” or larger and on any Sharp Over The Range Microwave Oven. This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. WARRANTY PERIODS Projector 1 year (bulb 90 days) To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact: SHARP ELECTRONICS OF CANADA LTD. SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9 (905) 568-7140 Web site: www.sharp.ca VALID IN CANADA ONLY