Panasonic WVRM70 - ACCESSORY Operating Instructions Manual

please read these instructions completely. 

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the pres- ence of uninsulated "dangerous volt- age" within the product's enclosure that may be of sufficient magnitude to con- stitute a risk of electric shock to per- sons. The exclamation point within an equi- lateral triangle is intended to alert the user to the presence of important oper- ating and maintenance (servicing) instructions in the literature accompa- nying the appliance. The serial number of this product may be found on the bot- tom of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. Warning: This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in strict accor- dance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SER- VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PER- SONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN SA 1965 SA 1966 For U.S.A CAUTION: Before attempting to connect or operate this prod- uct, please read the label on the bottom.

4 CONNECTIONS ............................................................................................................................................................ 7 OPERATING PROCEDURE ........................................................................................................................................... 13 SPECIFICATIONS ......................................................................................................................................................... 32

the optional WV-CP610 and WV-BP510 series CCTV Camera, enables remote control of camera settings. Also it is available to receive the alarm (motion detec- tor) signal multiplexed with the video signal from the WV-CP610 and WV-BP510 series camera. FEATURES The WV-RM70 Camera Controller enables remote con- trol of the following functions: • Remote control of camera settings for the WV- CP610 and WV-BP510 series camera, including Electronic Sensitivity Up, Electronic Shutter, and more. • Remote control of camera and auxiliary equipment, by using optional receiver and accessories, includ- ing: 1. Remote control of Pan/Tilt Head and Camera Housing. 2. Remote control of Motorized Zoom Lens : Focus, Zoom and Iris. Also it is available to receive the alarm (motion detec- tor) signal multiplexed with the video signal from the WV-CP610 and WV-BP510 series camera.

In order to prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Do refer to all servicing to qualified service person- nel. • Handle the unit with care. Do not abuse the unit. Avoid striking, shaking, etc. It could be damaged by improper handling or stor- age. • Do not expose the unit to rain or moisture, or try to operate it in wet areas. Do take immediate action if the unit becomes wet. Turn the power off and refer servicing to qualified service personal. Moisture can damage the unit and also create the danger of electric shock. • Do not use strong or abrasive detergents when cleaning the unit body. Do use a dry cloth to clean the unit when dirty. In case the dirt is hard to remove, use a mild deter- gent and wipe gently. • Do not operate the unit beyond its temperature, humidity or power source ratings. Do not use the unit in an extreme environment where high temperature or high humidity exist. Use the unit under conditions where temperatures are within 14˚F-140˚F (−10˚C - +60˚C) and humidity is below 90%. The input power source is 12V DC (10.8 - 16.0V DC). Caution: To prevent fire or shock hazard, the UL list- ed wire VW-1, style 1007 should be used for the cable for DC12V Input Terminal.

REMOTE OPERATE Camera Controller WV-RM 70 PROG ALARM RESET NORMAL SYSTEM ALARM OFF ON OFF IN OUT TERM VIDEO CAMERA DC12V IN GND GND ALARM OUT RESET OUT DATA T(A) T(B) R(A) R(B) q w e r t y u i o !0 !1 !2 !3 !4 !5 !6

This indicator lights up when DC power is supplied to the DC 12V Input Terminal. 2. Remote Indicator (REMOTE) This indicator lights up when this controller is con- trolled remotely by Personal Computer. 3. Left Switch (A) This switch is used to move the cursor (in the Setup Menu) in the left direction or move the Pan/Tilt Head toward the left direction. 4. Down Switch (C) This switch is used to move the cursor (in the Setup Menu) in the down direction or move the Pan/Tilt Head toward the down direction. 5. Up Switch (D) This switch is used to move the cursor (in the Setup Menu) in the up direction or move the Pan/Tilt Head toward the up direction. 6. Set Switch The mode selected in the setup menu is enabled by pressing this switch. 7. Right Switch (B) This switch is used to move the cursor (in the Setup Menu) in the right direction or move the Pan/Tilt Head toward the right direction. 8. Mode Selection Switch (NORMAL/ALARM OFF/SYSTEM) This switch is used to select the activated mode. Refer to the Mode Selection on page 13 for more details. 9. Program Switch (PROG) This switch is used to display the Program Menu on the monitor screen by pressing this switch for more than 2 seconds, 10. Alarm Reset Switch (ALARM RESET) When the unit is in the alarm mode, this indicator starts blinking. Press this switch to cancel alarm and the indicator light turns off. 11. Alarm Terminal RESET OUT: When the controller resets the acti- vated alarm by pressing the Alarm Reset Switch, the alarm reset output signal is provid- ed at this terminal for the Time Lapse VCR.

at this terminal for the Time Lapse VCR. 12. Data Terminal These terminals are used to transmit / receive control data to / from a Personal Computer. Use data grade cable, suitable for RS-485 (2 shielded, twisted pairs), cable length may be extended up to 4,000 ft. (1,200m). Designation Direction T (A) Personal Computer ←Controller T (B) Personal Computer ←Controller GND R (A) Personal Computer →Controller R (B) Personal Computer →Controller GND 13. Termination Switch (TERM ON/OFF) This switch is used to enable termination of this controller’s data terminal. 14. Video Output Connector (VIDEO OUT) A 1.0 Vp-p / 75Ωcomposite video signal is provid- ed at this connector. 15. Camera Input Connector (CAMERA IN) This connector accepts either a color or B/W com- posite video signal from the camera. Also, VD2, to synchronize camera in vertical timing, and data, to control camera site devices, are multiplexed through this connector. 16. DC 12V Input Terminal (DC 12V IN) This terminal accepts 12V DC (10.8 - 16.0V DC) power source. Cautions : 1. Connect to a 12V DC class 2 power supply only. 2. To prevent fire or shock hazard, the UL listed wire VW-1, style 1007 should be used for the cable for DC 12V Input Terminal.

Before connecting this controller, confirm the Dip Switch Setting if the system setting change is required. Pulse (VTR): +5V DC approx. 500msec. Initially, VTR position is selected at the factory. 2. Set switch (SW2) on the board to choose the char- acter display mode on the monitor. NOR : White with Black border REV : Black with White border Initially, normal (NOR) position is selected at the factory. OPC VTR REV NOR REV NOR SW1 SW2 SW5 SW3 SW4 Front Rear 1. Set switch (SW1) on the board to choose the alarm reset output sig- nal as either Open Collector (OPC) or Pulse (VTR). Open Collector (OPC) : 16V DC 100mA max. 3. Confirm switches (SW3) on the board are set to the position as shown. These switches are used only for factory test. 4. Confirm switch (SW4) on the board is set to the "VS" position. This switch is used only for fac- tory test. 1 2 3 4 OFF VD VS

line selection mode for data terminal. 4 LINE : normal connections are made. 2 LINE : simplified connections are made. Initially, 4 LINE is selected at the factory. The above switching should be made by qualified service personal or system installers. 2. Connection of Alarm Output Terminal • Make sure the polarity of the buzzer to meet with this terminal. The positive (+) terminal of the buzzer should be con- nected with the Alarm Output Terminal. • The Alarm Output Terminal is composed of the Open Collector Output and the capacity is 16V DC, 100mA or less. 2LINE 4LINE GND ALARM OUT RESET OUT (1) In case the buzzer is operable within the capacity of Alarm Output Terminal, connect buzzer as shown right. (2) In case the buzzer is not operable within the capacity of Alarm Output Terminal, the external relay unit should be used as shown below. GND ALARM OUT RESET OUT NC NO +12V C NC : Normally Closed NO : Normally Open C : Common To Buzzer Relay Buzzer

I Basic Connection TL Camera WV-CP610 Camera WV-CS304 Pan/Tilt Receiver Camera Controller WV-RM70 Time Lapse VCR Monitor Motion Detect Output Personal Computer RS-485 Converter (RS-485/ RS-232C)

I System 300 TL TL Time Lapse VCR PC WV-CU101 WV-CS304 WV-BS204 WV-CP610 WV-CP610 WV-RM70 WJ-SW208 WJ-MP404 WJ-SQ508 WV-CU300 RS-485 ALARM OUT WV-RM70 Converter (RS-485/ RS-232C) Converter (RS-485/ RS-232C) Monitor Monitor Time Lapse VCR

The maximum cable length in the system is approximately 3,000 ft. See the diagram below and set up the cable-loss compensation switch for each unit accordingly. For examples: Position of the switch of WV-RM70 0 ≤A < 1300 → S 1300 ≤A < 2300 → M 2300 ≤A < 3000 → L Position of the Position of the switch of WV-RM70 switch of WJ-MP404 S: 0 ≤A + B < 1300 → S S: 1300 ≤A + B < 2300 → M S: 2300 ≤A + B < 3000 → L M: 1300 ≤A + B < 2300 → S M: 2300 ≤A + B < 3000 → M L: → S WV-RM70 WV-RM70 WJ-MP404 A ft A ft 3,000 ft B ft Camera Camera

Computer I 4 Data Line (Dip Switch SW5 : 4 LINE) I 2 Data Line (Dip Switch SW5 : 2 LINE) T(A) T(B) R(A) R(B) R(A) R(B) T(A) T(B) Personal Computer Camera Controller T(A) T(B) R(A) R(B) R(A) R(B) T(A) T(B) Personal Computer Camera Controller T(A) T(B) R(A) R(B) R(A) R(B) T(A) T(B) R(A) R(B) T(A) T(B) Personal Computer Camera Controller T(A) T(B) R(A) R(B) Data Terminal Camera Controller Transmit Data Receive Data

1. Mode Selection This controller can select the activated mode by selecting Mode Selection Switch located on the front panel. Switch Position Functions NORMAL ALARM OFF SYSTEM Activated Mode Normal Mode Alarm Off Mode System Mode Function 1 : Controller setup Function 2 : Camera Setup (for WV-CP610 series) Function 3 : Camera Control Function 4 : Receiver Control Function 5 : Alarm Control Function 6 : Remote Control by Personal Computer Function 1 : Controller setup Function 2 : Camera Setup (for WV-CP610 series) Function 3 : Camera Control Function 4 : Receiver Control Function 6 : Remote Control by Personal Computer Function 1 : Controller setup Function 5 : Alarm Control Function 6 : Remote Control by Personal Computer (Except Camera Site Control)

By pressing the Program (PROG) Switch for more than 2 seconds, when Mode Selection Switch is selected at Normal (NORMAL) position or Alarm Off (ALARM OFF) position, the following displays appear on the monitor screen. Fig. 1 As shown in Fig. 2, the Program Menu has four main sub menus: Camera Control, Receiver Control, Camera Setup and Controller Setup. These sub menus are fur- ther divided in to additional submenus. Program Menu Camera Control Iris Control Sens Up Control Shutter BLC AGC White Balance Receiver Control Pan/Tilt Control (Manual) Zoom/Focus Control AUX 1, 2 Control Wiper/Defroster Pan Action (Auto/Random Panning) Camera Set Up Controller Set Up System Communication Fig. 2 Move the cursor to the desired program by pressing the Up (D) Switch or the Down (C) Switch on the con- troller, then press the Set Switch to select program where the cursor is positioned. ** Program Menu ** Camera Control * Receiver Control * Camera Set Up * Controller Set Up *

Move the cursor to the “Camera Control” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the fol- lowing display on the monitor screen. Fig. 3 Press the Set Switch repeatedly to select the desired functions. The function is selected as shown in the fol- lowing sequence. →Iris →Sens Up →Shutter →BLC → ←ATW, AWC ←AGC ← 3-1. Lens Iris Control The following function is available only when speci- fied lens is mounted on the specified camera. 1. Display the Iris Menu as shown in Fig. 4 by repeat- ing the previous procedures. Fig. 4 2. Press the Right (B) Switch to open the lens iris or press the Left (A) Switch to close the lens iris. Adjust the lens iris by pressing the switches to obtain the proper picture exposure. While pressing the switches, the character is inversely displayed on the monitor screen. 3. By pressing both of these switches at the same time for one second, the lens iris is set to the facto- ry preset condition. ** Program Menu ** Camera Control * Receiver Control * Camera Set Up * Controller Set Up * ←close Iris open→ B ←close Iris open→

The following function is available only when speci- fied camera with the electronic sensitivity feature is used. 1. Display the Sens Up Menu as show in Fig. 5 by repeating the previous procedures. Fig. 5 2. Press the Up (D) Switch or the Down (C) Switch to select the desired mode, “Off”, “Auto” or “Manu”. 3. When selected “Auto” or “Manu” mode, press the Right (B) Switch to select a higher sensitivity up setting, or press the Left Switch to select a lower sensitivity up setting. 3-3. Electronic Shutter The following function is available only when speci- fied camera with the electronic shutter feature is used. 1. Display the Shutter Menu as shown in Fig. 6 by repeating the previous procedures. Fig. 6 2. Press the Up (D) Switch or the Down (C) Switch to select the desired mode, “On” or “Off”. 3. When selected “On” mode, press the Right (B) Switch to select faster shutter speeds or press the Left (A) Switch to select slower shutter speeds. ↑Sens Up↓:off ↑Sens Up↓:←A x10→ ↑Shutter↓:off ↑Shutter↓:←/10000→

The following function is available only when speci- fied camera with the Auto/Preset BLC Function is used. 1. Display the BLC Menu as shown in Fig. 7 by repeating the previous procedures. Fig. 7 2. Press the Up (D) Switch or the Down (C) Switch to select the desired mode, “Off”, “Auto” or “Preset”. 3-5. Gain Control The following function is available only when speci- fied camera with the AGC feature is used. 1. Display the AGC Menu as shown in Fig. 8 by repeating the previous procedures. ↑BLC↓:Auto ↑AGC↓:On Fig. 8 2. Press the Up (D) Switch or the Down (C) Switch to select the desired mode, “On” or “Off”. 3-6. White Balance The following function is available only when the specified camera with the ATW/AWC White Balance Function is used. 1. Display the ATW, AWC Menu as shown in Fig. 9 by repeating the previous procedures. ←ATW,AWC→:ATW Fig. 9

select desired mode, “ATW” or “AWC”. After completing the above settings, press the Program (PROG) Switch to return the previous Program Menu as shown in Fig. 1. To return to the normal camera picture, press the Program (PROG) Switch again. 4. Receiver Control Press the Program (PROG) Switch for more than 2 sec- onds to display the Program Menu. Move the cursor to the “Receiver Control” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the following dis- play on the monitor screen. Fig. 10 ** Program Menu ** Camera Control * Receiver Control * Camera Set Up * Controller Set Up * ↑Tilt↓/ ←Pan→ B Press the Set Switch repeatedly to select the desired functions. The function is selected as shown in the following sequence. →Tilt/Pan →Zoom/Focus →Aux → ←Pan Action ← Wiper/Defroster ← Note : Normally, a WV-RC100 or WV-RC150 Recei- ver is required to perform the following func- tions. 4-1. Pan/Tilt Control (Manual Operation) 1. Display the Tilt/Pan Menu as shown in Fig. 11 by repeating the previous procedures. ↑Tilt↓/ ←Pan→ Fig. 11

move the Pan/Tilt Head toward up or down. Press the Rignt (B) Switch or the Left (A) Switch to move the Pan/Tilt Head toward right or left. While press- ing these switches, the character is inversely dis- played on the monitor screen. 3. If the Up (D) Switch and the Right (B) Switch are pressed at the same time, the Pan/ Tilt Head moves diagonally towards Up and Right. 4-2. Zoom/Focus Control 1. Display the Zoom/Focus Menu as shown in Fig. 12 by repeating the previous procedures. Fig. 12 ↑t Z w↓/ ←n F f→ 2. Press the Up (D) Switch or the Down (C) Switch to adjust the lens zoom to achieve the desired picture while observing the monitor screen. Press the Up (D) Switch to optically bring an object closer, pressing the Down (C) Switch has the reverse effect. 3. Press the Right (B) Switch or the Left (A) Switch to adjust the lens focus to achieve a sharply picture while observing the monitor screen. 4-3. Auxiliary Control 1. Display the Aux Menu as shown in Fig. 13 by repeating the previous procedures. Fig. 13 ←1:On Aux →2:Off

off the user’s auxiliary switch 1 in the Receiver (WV- RC100 or WV-RC150). 3. Press the Right (B) Switch repeatedly to turn on or off the user’s auxiliary switch 2 in the Receiver (WV- RC100 or WV-RC150). 4-4. Wiper / Defroster Control 1. Display the Wip / Def Menu as shown in Fig. 14 by repeating the previous procedures. Fig. 14 2. Press the Left (A) Switch repeatedly to turn on or off the housing wiper. 3. Press the Right (B) Switch repeatedly to turn on or off the housing defroster. ←Wip:Off,→Def:On 4-5. Pan Action (Auto/Random Panning) 1. Display the Pan Menu as shown in Fig. 15 by repeating the previous procedures. ←A Pan:Off R→ Fig. 15 2. Press the Right (B) Switch or the Left (A) Switch repeatedly to select the desired Panning mode off, Auto or Random. After completing the above settings, press the Program (PROG) Switch to return the previous Program Menu as shown in Fig. 1. To return to the normal camera picture, press the Program (PROG) Switch again.

The following functions are only available with the camera that has set up functions such as the Panasonic WV-CP610 or WV-BP510 series camera. 1. Press the Program (PROG) Switch for more than 2 seconds to display the Program Menu. 2. Move the cursor to the “Camera Set Up” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the fol- lowing display on the monitor screen. ** SET UP ** CAMERA ID OFF * ALC/ELC ALC * SHUTTER OFF AGC ON SENS UP OFF SYNC INT WHITE BAL ATW * WIDE D-RANGE OFF MOTION DET OFF DNR OFF END SET UP ENABLE ** Program Menu ** Camera Control * Receiver Control * Camera Set Up * Controller Set Up * B Fig. 16 3. Select the desired item by pressing the Up (D) Switch or the Down (C) Switch and then select the desired mode by pressing the Right (B) Switch or the Left (A) Switch. Press the Set Switch to execute the selection or entering the sub menu. Notes: • Refer to the Operating Instructions of the camera for more details. • While pressing both the Left (A) Switch and the Right (B) Switch, press the Set Switch for a few seconds on the SET UP Menu as shown in Fig.16. At this time all adjustments and selections are being changed to the factory default settings.

Camera Control * Receiver Control * Camera Set Up * Controller Set Up * 6. Controller Set Up 6-1. Entering Controller Setup Menu 1. Press the Program (PROG) Switch for more than 2 seconds to display the Program Menu. 2. Move the cursor to the “Controller Set Up” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the fol- lowing display on the monitor screen. Fig. 17 ** Controller Set Up ** System * Communication * Set up Disable B ** Controller Set Up ** System * Communication * Set up Enable ** Controller Set Up ** System * Communication * Set up Disable 3. Move the cursor to the “Disable” position by press- ing the Up (D) Switch or the Down (C) Switch, then press the Set Switch and “Enable” is dis- played. B Fig. 18 4. Select the desired item by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to select item where the cursor is posi- tioned. Press the Program (PROG) Switch to return to the previous Program Menu as shown in Fig. 1. To return to the normal camera picture, press the Program (PROG) Switch again. Note: When Mode Selection Switch is selected at System (SYSTEM) position, Controller Set Up Menu appears by pressing the Program (PROG) Switch for more than 2 seconds.

1. Display the Controller Set Up Menu by repeating the previous procedures. ** System ** Camera ID Off * Cable Comp S Alarm Time 60 S Alarm Display Off Return B ** Controller Set Up ** System * Communication * Set up Enable Fig. 19 2. Move the cursor to the “System” position by press- ing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the System Menu as shown in Fig. 19. 3. Move the cursor to the desired item by pressing the Up (D) Switch or the Down (C) Switch and then select the desired mode by pressing the Right (B) Switch or the Left (A) Switch. 4. After completing the above settings, move the cur- sor to the “Return” Position then press the Set Switch to return to the previous Controller Set Up Menu. 5. Press the Program (PROG) Switch to return to the previous Program Menu. To return to the normal camera picture, press the Program (PROG) Switch again. (1) Camera ID Setting 1. Display the System Menu as shown in Fig. 20 by repeating the previous procedures. Fig. 20 2. Move the cursor to the “Camera ID” position by pressing the Up (D) Switch or the Down (C) Switch, then select either “On” or “Off” mode by pressing the Right (B) Switch or the Left (A) Switch. 3. When the Camera ID needs editing, perform the following steps by using the sub menu of Camera ID. ** System ** Camera ID Off * Cable Comp S Alarm Time 60 S Alarm Display Off Return

................ ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789 ().,'":;&#!?= +-*/%$ ←→ Space Posi Return Clear DOOR .......... -24- Fig. 21 5. Move the character cursor to the desired letter by pressing the Up (D) Switch, Down (C) Switch, Right (B) Switch and Left (A) Switch, then press the Set Switch. The selected letter is written to the editing cur- sor and the editing cursor moves to right auto- matically. 6. Repeat the above procedure until all character editing is completed. Character Cursor Editing Cursor Character Areas Command Editing Area Fig. 22 ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789 ().,'":;&#!?= +-*/%$ ←→ Space Posi Return Clear DOOR .......... 4. Move the cursor to the “Camera ID” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to dis- play the Camera ID Editing Menu as shown in Fig. 21. 7. When the position of the editing cursor is to be shifted in the editing area, move the character cursor to the “←“ or “→“ by pressing the switches, then press the Set Switch. This function is used to move the editing posi- tion or to correct an individual character. Fig. 23 N N

DOOR .......... -25- Fig. 24 9. When all characters in the editing area are to be erased, move the character cursor to the “Clear” position by pressing the switches, then press the Set Switch. Fig. 25 10. After completing the editing Camera ID, the Camera ID display position on the monitor screen can be set as follow. Move the charac- ter cursor to the “Posi” position by pressing the switches, then press the Set Switch to display the Camera ID as shown in Fig. 26. N N ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789 ().,'":;&#!?= +-*/%$ ←→ Space Posi Return Clear DOOR .......... N 8. When blank space is needed, move the char- acter cursor to the “Space” position by press- ing the switches, then press the Set Switch. The blank space is inserted into the cursor position in the editing area. N ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789 ().,'":;&#!?= +-*/%$ ←→ Space Posi Return Clear DOOR .......... DOOR......... B Fig. 26

Camera ID Off * Cable Comp S Alarm Time 60 S Alarm Display Off Return -26- The Camera ID display position can be placed anywhere on the screen by pressing the Up (D) Switch, Down (C) Switch, Left (A) Switch and Right (B) Switch. Notes : 1. The positioning of the Camera ID stops at the edges of the monitor screen except the right side of the monitor screen. 2. The Camera ID moves faster when the Up (D) Switch, Down (C) Switch, Right (B) Switch or Left (A) Switch is kept pressed. 11. After completing the positioning, press the Set Switch to return to the Camera ID Editing Menu as shown in Fig. 21. 12. Move the Character cursor to the “Return” position by pressing the switches, then press the Set Switch to return to the System Menu. (2) Cable Compensation Setting 1. Display the System Menu as shown in Fig. 27 by repeating the previous procedures. Fig. 27 2. Move the cursor to the “Cable Comp” position by pressing the Up (D) Switch or the Down (C) Switch, then select the most suitable cable length as shown below by pressing the Right (B) Switch or the Left (A) Switch repeatedly. S : Up to 1,300ft (400m) M : 1,300ft (400m) to 2,300ft (700m) L : 2,300ft (700m) to 3,000ft (900m) (When using RG-59U, BELDEN 9259 or equiv- alent cable)

Unit Number 1 Baud Rate 9600 Data Bit 8 Parity Check None Stop Bit 1 Xon/Xoff Not Use Wait Time Off Delay Time Off Alarm Data Off Return ** Controller Set Up ** System * Communication * Set up Enable ** System ** Camera ID Off * Cable Comp S Alarm Time 60 S Alarm Display Off Return -27- (3) Alarm Time Setting 1. Display the System Menu as shown in Fig. 27 by repeating the previous procedures. 2. Move the cursor to the “Alarm Time” position by pressing the Up (D) Switch or the Down (C) Switch, then select the desired alarm time, 0.5s - 120s, by pressing the Right (B) Switch or the Left (A) Switch repeatedly. (4) Alarm Display Setting 1. Display the System Menu as shown in Fig. 27 by repeating the previous procedures. 2. Move the cursor to the “Alarm Display” posi- tion by pressing the Up (D) Switch or the Down (C) Switch, then select either “On” or “Off” mode by pressing the Right (B) Switch or the Left (A) Switch repeatedly. To return to the Controller Set Up Menu, move the cursor to the “Return” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch. Fig. 28 6-3. Communication Setup 1. Display the Controller Set Up Menu by repeating the previous procedures. 2. Move the cursor to the “Communication” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the fol- lowing display on the monitor screen. Fig. 29 B

Unit Number 1 Baud Rate 9600 Data Bit 8 Parity Check None Stop Bit 1 Xon/Xoff Not Use Wait Time Off Delay Time Off Alarm Data Off Return -28- 3. Move the cursor to the desired item by pressing the Up (D) Switch or the Down (C) Switch and then select the desired mode by pressing the Right (B) Switch or the Left (A) Switch. 4. After completing the above settings, move the cur- sor to the “Return” position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to return to the previous Controller Set Up Menu. 5. Press the Program (PROG) Switch to return to the previous Program Menu. To return to the normal camera picture, press the Program (PROG) Switch again. (1) Unit Number Setting 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. Fig. 30 2. Move the cursor to the “Unit Number” position by pressing the Up (D) Switch or the Down (C) Switch, then select the desired unit num- ber, 1-16, by pressing the Right (B) Switch or the Left (A) Switch repeatedly. (2) Baud Rate Setting 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Baud Rate” position by pressing the Up (D) Switch or the Down (C) Switch. Select the desired baud rate, 1200 - 19200, by pressing the Right (B) Switch or the Left (A) Switch repeatedly. (3) Data Bit Setting 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Data Bit” position by pressing the Up (D) Switch or the Down (C) Switch. Select the desired data bit, 7 or 8, by pressing the Right (B) Switch or the Left (A) Switch.

1. Display the communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Parity Check” position by pressing the Up (D) Switch or the Down (C) Switch. Select the desired parity check, None, Odd or Even, by pressing the Right (B) Switch or the Left (A) Switch. (5) Stop Bit Setting 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Stop Bit” position by pressing the Up (D) Switch or the Down (C) Switch. Select the desired stop bit, 1 or 2, by pressing the Right (B) Switch or the Left (A) Switch. (6) Xon / Xoff 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Xon / Xoff” position by pressing the Up (D) Switch or the Down (C) Switch. Select desired mode, Not Use or Use, by pressing the Right (B) Switch or the Left (A) Switch. (7) Wait Time Setting 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Wait Time” position by pressing the Up (D) Switch or the Down (C) Switch. Select the desired wait time, Off or 100mS - 1000mS by pressing the Right (B) Switch or the Left (A) Switch repeatedly. (8) Delay Time Setting 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Delay Time” position by pressing the Up (D) Switch or the Down (C) Switch. Select the desired delay time, Off or 10mS - 100mS, by pressing the Right (B) Switch or the Left (A) Switch repeatedly. (9) Alarm Data Setting This setting determines whether the alarm data received from the camera is transmitted or not

computer. Select the alarm data transmission mode as fol- lows. Off: The controller does not transmit alarm data to the computer. Auto 1: The controller relays alarm data every time it receives data from the camera. Auto 2: The controller transmits alarm data periodi- cally to give the computer time to process the latest data before receiving new data. Use this mode if the computer takes time to process all of received data. 1. Display the Communication Menu as shown in Fig. 30 by repeating the previous procedures. 2. Move the cursor to the “Alarm Data” position by pressing the Up (D) Switch or the Down (C) Switch. Select the desired mode, “Auto 1”, “Auto 2” or “Off”, by pressing the Right (B) Switch or the Left (A) Switch. To return to the Controller Set Up Menu, move the cursor to the “Return” position by pressing the Up (D) Switch or the Down (C) Switch then press the Set Switch. Note: For more details on the settings, refer to the operating instructions of the connected equip- ment. ←Alarm→ Notes: • “Alarm” display position can be placed at upper or lower right side of the monitor screen. Refer to the Title Setting on page 23 for setup method. • It is available to choose the “Alarm” display mode on the monitor screen. Refer to the Alarm Display Setting on page 27 for setup method. ALARM RESET 7. Alarm Control (1) Alarm Operation When this unit receives an alarm from the camera, such as Panasonic WV-CP610 is activated at motion detect mode, or camera site receiver WV- RC100 or WV-RC150, the Alarm Indicator blinks. The indicator keeps blinking and “Alarm” is dis- played on the monitor screen.

formed, the picture may be disturbed momen- tarily. This is normal and is not indicative of a prob- lem. q e w Right Switch Down Switch Up Switch Left Switch Set Switch (2) To Cancel Alarm Press the Alarm Reset (ALARM RESET) Switch for alarm reset. The indicator light turns off and “Alarm” display on the monitor screen disappears. 8. All Reset It is possible to undo all the changes the end user made to return to the factory settings without having to go through each individual menu. This feature is called the ALL RESET operation and is accomplished as follows : 1. Ensure that the Program Menu is not displayed. (a normal camera picture is displayed). 2. While pressing both the Left (A) Switch and the Right (B) Switch, press the Set Switch for more than 2 seconds. The “All Reset” display appears momentarily on the monitor screen. At this time all adjustments and selections are being changed to the factory default settings.

DC12V (DC 10.8V - 16.0V), 230mA Camera Input : Composite Video Signal: 1.0Vp-p / 75Ω VD2 Output Signal: 2.5Vp-p / 75Ω Data Signal: 0.5Vp-p / 75Ω Video Output : Composite Video Signal: 1.0Vp-p / 75Ω VD2 Input Signal: more than 1.5Vp-p / 75Ω (Mode Selection Switch is set at SYSTEM) Data Signal: 0.5Vp-p / 75Ω (Mode Selection Switch is set at SYSTEM) Alarm Output : Open collector output : 16V DC, 100mA max. Alarm Reset Output : Pulse (VTR) : +5V DC 500msec. or Open collector output : 16V DC, 100mA max. Data Input / Output : RS-485 Remote Control Functions Camera Set Up : For Panasonic WV-CP610 or WV-BP510 series camera Camera Functions : Electronic Sensitivity Up Mode Select : Auto / Manual / Off Electronic Shutter : On / Off, Shutter Speed Select Back Light Compensation : Auto / Preset/Off Automatic Gain Control : On / Off White Balance : ATW / AWC Lens Functions : Iris : Open / Close / Preset Focus : Near / Far Zoom : Tele / Wide Housing : Wiper : On / Off, Defroster : On / Off Pan / Tilt : Manual Pan : Right / Left, Manual Tilt : Up / Down Auto Pan : On / Off, Random Pan : On / Off Auxiliary Switch : Aux 1-2 : On / Off

14˚F - 140˚F (−10˚C - +60˚C) Ambient Operating Humidity : Less than 90% Dimensions : 5-7/16” (W) x 7-5/16” (D) x 2”(H) 138 (W) x 185 (D) x 51 (H) mm Weight : 1.8 lbs. (0.8 kg) Weight and dimensions shown are approximate. Specifications are subject to change without notice.

N 19 Video Imaging Systems Company A Division of Panasonic Broadcast & Television Systems Company A Unit of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 4H-2, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southeast: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211 Southwest: 8105 Beltsline Road, Suite 100, Irving, TX 75063 (927) 915-1334 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC. San Gabriel Industrial Park, 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00630 (809)750-4300