Savin 5308L Operating Instructions Manual

reference. For safety, please follow the instructions in this manual.

maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read the Safety Information before using this machine. It contains important information related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS. Notes: Some illustrations may be slightly different from your machine. Certain options may not be available in some countries. For details, please contact your local dealer. Two kinds of size notation are employed in this manual. With this machine refer to the Inch version. For good print quality, Gestetner recommends that you use genuine Gestetner master and ink. Gestetner shall not be responsible for any damage or expense that might result from the use of parts other than genuine Gestetner parts in your Gestetner office product. Power Source: 120 V, 60 Hz, 2.5 A or more Please be sure to connect the power cord to a power source as above. For details about power source, see ⇒ P.110 “Power connection”. Read this manual carefully before you use this product and keep it handy for future reference. For safety, please follow the instructions in this manual.

Notice: This equipment has been tested and found to comply with the limits for a Class A digital devices, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, might cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note to users in Canada Note: This Class A digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement: Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. In accordance with ISO Standard 7001, this machine uses the following symbols for the main switch: a a a a means POWER ON. b b b b means POWER OFF. SAVIN CORPORATION 333 Ludlow Street Stamford CT06904 203–967–5000

followed. Safety During Operation In this manual, the following important symbols are used: Examples Of Indications R WARNING: Ignoring this warning could cause serious injury or even death. R CAUTION: Ignoring this caution could cause injury or damage to property. Symbols R mean a situation that requires you take care. Do NOT carry out the operation represented by this symbol m. This example means “Do not take apart”. Symbols $ mean you MUST perform this operation. This example means “You must remove the wall plug”.

the inside front cover of this manual. • Avoid multi-wiring. • Do not damage, break or make any modifications to the pow- er cord. Do not place heavy objects on it, pull it hard or bend it more than necessary. These actions could cause an elec- tric shock or fire. • Do not plug or unplug the power cord with your hands wet. Otherwise, an electric shock might occur. • Make sure the wall outlet is near the machine and freely ac- cessible so that in event of an emergency it can be un- plugged easily. • Do not remove any covers or screws other than those spec- ified in this manual. Some parts of the machine are at a high voltage and could give you an electric shock. When the ma- chine needs to be checked, adjusted, or repaired, contact your service representative. • Do not take apart or attempt any modifications to this ma- chine. There is a risk of fire, electric shock, explosion or loss of sight. • If the machine looks damaged or breaks down, smoke is coming out, there is a strange smell or anything looks un- usual, immediately turn off the main switch then unplug the power cord from the wall. Do not continue using the ma- chine in this condition. Contact your service representative. • If metal, liquid or foreign matter falls into the machine, turn off the main switch and unplug the main power cord. Con- tact your service representative. Do not keep using the ma- chine with a fault or defect. • Do not put any metal objects or containers holding water (e.g. vases, flowerpots, glasses) on the machine. If the con- tents fall inside the machine, a fire or electric shock could occur.

tric shock might occur. • Do not place the machine on an unstable or tilted surface. If it top- ples over, it could cause injury. • After you move the machine, fix it with the caster fixture. Other- wise, the machine might move or come down to cause a personal injury. • When you move the machine, unplug the power cord from the wall outlet to avoid fire or electric shock. • When the machine will not be used for a long time, unplug the power cord. • When you pull out the plug from the socket, grip the plug to avoid damaging the cord and causing fire or electric shock. • If you use the machine in a confined space, make sure there is a continuous air turnover. • Do not reuse stapled paper. Do not use aluminum foil, carbon- containing paper or other conductive paper. Otherwise, a fire might occur. • This machine has been tested for safety using this supplier's parts and consumables. We recommend you only use these specified supplies. • This equipment is only to be installed by a qualified service per- sonnel. • Deliver to collection point for waste products. Do not be disposed of via domestic refuse collection. • If ink comes into contact with your eyes, rinse immediately in run- ning water. In the case of any abnormal symptoms, consult a doctor.

• If ink is ingested, force vomiting by drinking a strong saline solu- tion and consult a doctor immediately. • Be careful not to cut yourself on any sharp edges when you reach inside the machine to remove misfed sheets of paper or masters. • Do not touch the belt at the end of the paper delivery table. Do not insert your hands under the paper feed table or the paper de- livery table. You might be injured.

Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the in- structions under this symbol. Be sure to read the instructions, all of which are de- scribed in the Safety Information section. R CAUTION: This symbol indicates a potentially hazardous situation that might result in mi- nor or moderate injury or property damage that does not involve personal injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are described in the Safety Information section. * The statements above are notes for your safety. Important If this instruction is not followed, paper might be misfed, originals might be damaged, or data might be lost. Be sure to read this. Preparation This symbol indicates the prior knowledge or preparations required before op- erating. Note This symbol indicates precautions for operation, or actions to take after misop- eration. Limitation This symbol indicates numerical limits, functions that cannot be used together, or conditions in which a particular function cannot be used. Reference This symbol indicates a reference. [ ] Keys that appear on the machine's panel display. { } Keys built into the machine's operation panel.

O OO O Standard Printing See ⇒ P.5 “Standard Printing”. O OO O Adjusting The Print Image Position See ⇒ P.8 “Adjusting The Print Image Position”. O OO O Adjusting The Print Image Density See ⇒ P.10 “Adjusting The Print Image Density”. O OO O Making Half-tone Prints See ⇒ P.11 “Tint Mode—Making Half-tone Prints”. O OO O Making Clear Prints See ⇒ P.12 “Fine Mode—Making Clear Prints”. O OO O Changing The Print Speed See ⇒ P.13 “Changing The Printing Speed”. O OO O Reducing And Enlarging Using Preset Ratios See ⇒ P.15 “Preset Reduce/Enlarge—Reducing And Enlarging Using Preset Ra- tios”. O OO O Erasing Center And Edge Margins See ⇒ P.17 “Center/Edge Erase—Erasing Center And Edge Margins”. GRREDU0E GRENLA0E GRMARG0E

See ⇒ P.19 “Edge Erase—Erasing Edge Margins”. O OO O Erasing The Shadow Of Pasted Originals See ⇒ P.21 “Paste Shadow Erase—Erasing The Shadow Of Pasted Originals”. O OO O Printing On Thick Or Thin Paper See ⇒ P.22 “Printing On Thick Or Thin Paper”. O OO O Selecting Original Type See ⇒ P.23 “Selecting Original Type”. O OO O Ink Saving See ⇒ P.24 “Economy Mode—Ink Saving”. O OO O Printing From Several Originals At Once See ⇒ P.25 “Auto Cycle—Printing From Several Originals At Once”. O OO O Group Printing From The Same Original See ⇒ P.27 “Class Mode—Group Printing From The Same Original”. O OO O Group Printing From Different Originals See ⇒ P.29 “Memory Mode—Group Printing From Different Originals”. GRCLAS0E R R R R R R R D C B GRCLAS1E A A B C D

See ⇒ P.32 “Combine Copies—Combining 2 Originals Into One Print”. O OO O Skip Feed Printing See ⇒ P.35 “Skip Feed Printing”. O OO O Storing Your Print Settings In Memory See ⇒ P.36 “Program—Storing Your Print Settings In Memory”. O OO O Printing Secret Documents See ⇒ P.40 “Security Mode—Printing Secret Documents”. O OO O Making Color Prints See ⇒ P.49 “Making Color Prints”. O OO O Printing In Two Colors See ⇒ P.51 “Printing In Two Colors”. GRCOMB0E 2 1 1 2

Machine Exterior 1. Front Door Open for access to the inside of the ma- chine. 2. Operation Panel Operator controls and indicators are lo- cated here. See ⇒ P.xii “Operation Panel”. 3. Platen Cover Lower this cover over an original before printing. 4. Original Table Release Lever Use to open the original table unit when installing the master. 5. Feed Roller Pressure Lever Use to adjust the contact pressure of the paper feed roller according to paper thickness. 6. Paper Feed Side Plates Use to prevent paper skew. 7. Paper Feed Table Set paper on this table for printing. 8. Side Table Fine Adjusting Dial Use to shift the paper feed table side- ways. 9. Paper Feed Table Down key Press to lower the paper feed table. TSLH01EE 2 3 4 5 6 7 8 9 1 10

Flip up when you use the keys under- neath. Machine Interior 1. Document Feeder (Option) Original inserted into the document feed- er are individually and automatically fed onto and removed from the exposure glass. See ⇒ P.41 “Printing Using The Op- tional 30 Originals Document Feeder”. 2. Paper Delivery Side Plates Use to align the prints on the paper deliv- ery table. 3. Paper Delivery End Plate Use to align the leading edge of prints. 4. Paper Delivery Table Completed prints are delivered here. 5. Main Switch Use to turn the power on or off. 6. Drum Unit The master is wrapped around this unit. 7. Drum Unit Lock Lever Lift to unlock and pull out the drum unit. 8. Ink Holder Set the ink cartridge in this holder. TSLH01DE 8 1 2 3 4 5 6 7

Note Ì Other options: • Color Drum: LG drum • Color Drum: B4 drum • Tape Dispenser • Key Counter TSLP015E

Press to make prints of secret documents. See ⇒ P.40 “Security Mode—Printing Se- cret Documents”. 2. {{{{Paste Shadow Erase}}}} key Press to erase the shadow of pasted orig- inals. See ⇒ P.21 “Paste Shadow Erase— Erasing The Shadow Of Pasted Originals”. 3. {{{{Tint}}}} key Press to make half-tone prints. See ⇒ P.11 “Tint Mode—Making Half-tone Prints”. 4. {{{{Image Density}}}} key Press to make prints darker or lighter. See ⇒ P.10 “Adjusting The Print Image Densi- ty”. 5. Check Indicator This indicator lights when you have se- lected one or more of the functions ac- cessed by lifting the flip up cover and pressing the keys underneath (e. g. {Secu- rity} key, {Paste Shadow Erase} key etc.). This lets you know whether one or more of these functions is selected, even if the cover is lowered. 6. {{{{Skip Feed}}}} key Press to select skip feed printing. See ⇒ P.35 “Skip Feed Printing”. 7. {{{{Center/Edge Erase}}}} key Press to print book originals that have a solid image on the center or edges. See ⇒ P.17 “Center/Edge Erase—Erasing Center And Edge Margins”. 8. {{{{ }}}} and {{{{ }}}} keys ( Scroll keys) Press to select size and direction of paper or original in Center/Edge Erase. 9. {{{{Reduce}}}} key Press to reduce the image. See ⇒ P.15 “Preset Reduce/Enlarge—Reducing And En- larging Using Preset Ratios”. 10. {{{{Full Size}}}} key Press to make full size prints. 11. {{{{Enlarge}}}} key Press to enlarge the image. See ⇒ P.15 “Preset Reduce/Enlarge—Reducing And En- larging Using Preset Ratios”. 12. {{{{Economy}}}} key Press to save ink. See ⇒ P.24 “Economy Mode—Ink Saving”. 21 20 14 13 12 10 9 8 7 6 11 1 2 3 4 5 15

Press to select Letter, Photo, or Letter/ Photo mode. See ⇒ P.23 “Selecting Origi- nal Type”. 14. {{{{Fine}}}} key Press to select the fine image. See ⇒ P.12 “Fine Mode—Making Clear Prints”. 15. {{{{Image Position}}}} key Press to shift the image forwards or back- wards. See ⇒ P.8 “Adjusting The Print Im- age Position”. 16. {{{{Program}}}} key Press to input or recall user programs. See ⇒ P.36 “Program—Storing Your Print Settings In Memory”. 17. {{{{Clear Modes}}}} key Press to clear the previously entered job settings. 18. {{{{Auto Cycle}}}} key Use to process the master and make prints automatically. See ⇒ P.25 “Auto Cycle—Printing From Several Originals At Once”. 19. {{{{Proof}}}} key Press to make proof prints. 20. {{{{WWWW}}}} and {{{{VVVV}}}} keys (Speed keys) Press to adjust the printing speed. See “Print Speed” in ⇒ P.115 “Main Frame”. 21. {{{{Memory/Class}}}} key Press to select Memory or Class mode. See ⇒ P.27 “Class Mode—Group Printing From The Same Original” or ⇒ P.29 “Mem- ory Mode—Group Printing From Different Originals”. 22. {{{{Number}}}} keys Press to enter the desired number of prints and data for selected modes. 23. {{{{#}}}} key Use to enter data in selected modes. 24. {{{{Clear/Stop}}}} key While entering numbers, press to cancel a number you have entered. While copying, press to stop copying. 25. {{{{Start}}}} key Press to make a master. 26. {{{{Print}}}} key Press to start printing. TSLS021N 26 25 24 23 22 16 17 18 19

These indicators are lit when a non-stan- dard condition occurs within the ma- chine. 2. Memory/Class Indicator Shows the number entered in Memory or Class mode. 3. Speed Indicators These indicators show the printing speed that is selected. 4. Counter Displays the number of prints entered. While printing, it shows the number of prints remaining. 5. Guidance Display Display the machine's condition. 5 1 2 4 3

1.OPERATION Printing Paper............................................................................................ 1 Originals..................................................................................................... 2 Preparation For Printing ........................................................................... 3 Loading Paper............................................................................................... 3 Setting Up The Paper Delivery Table............................................................ 4 Standard Printing ...................................................................................... 5 Restoring Paper Feed And Paper Delivery Tables................................. 7 Adjusting The Print Image Position......................................................... 8 Shifting The Print Image Position Forward Or Backward.............................. 8 Shifting The Print Image Position To The Right Or Left................................ 8 Adjusting The Print Image Density........................................................ 10 Before Making A Master.............................................................................. 10 After Making A Master................................................................................. 10 Tint Mode—Making Half-tone Prints...................................................... 11 Fine Mode—Making Clear Prints............................................................ 12 Changing The Printing Speed ................................................................ 13 Stopping The Machine During The Multi-print Run.............................. 14 When You Want To Stop The Machine During The Multi-print Run And Print The Next Original ........................................................................................ 14 When You Want To Change The Number Of Prints Entered Or Check The Completed Prints......................................................................................... 14 Preset Reduce/Enlarge—Reducing And Enlarging Using Preset Ratios 15 Center/Edge Erase—Erasing Center And Edge Margins..................... 17 Edge Erase—Erasing Edge Margins...................................................... 19 Paste Shadow Erase—Erasing The Shadow Of Pasted Originals...... 21 Printing On Thick Or Thin Paper............................................................ 22 Printing On Thick Paper.............................................................................. 22 Printing On Thin Paper................................................................................ 22 Selecting Original Type........................................................................... 23 Economy Mode—Ink Saving .................................................................. 24 Auto Cycle—Printing From Several Originals At Once ....................... 25 Class Mode—Group Printing From The Same Original....................... 27 Memory Mode—Group Printing From Different Originals................... 29 Combine Copies—Combining 2 Originals Into One Print ................... 32 Skip Feed Printing................................................................................... 35

Storing Your Settings .................................................................................. 36 Recalling A Program ................................................................................... 37 Protecting A Program.................................................................................. 38 Removing Program Protection.................................................................... 39 Security Mode—Printing Secret Documents ........................................ 40 2.OPTIONAL FUNCTIONS Printing Using The Optional 30 Originals Document Feeder.............. 41 Document Feeder Exterior.......................................................................... 41 Originals...................................................................................................... 41 Setting Originals In The Document Feeder................................................. 42 Combine Copies With The Document Feeder ............................................ 44 Memory Mode With The Document Feeder................................................ 45 Color Printing Using The Optional Color Drum.................................... 49 Making Color Prints..................................................................................... 49 Changing The Color Drum Unit................................................................... 49 Printing In Two Colors................................................................................. 51 3.SERVICE PROGRAM MODE Accessing Service Programs................................................................. 53 Changing The Settings Of Service Programs....................................... 54 Service Program Menu ............................................................................... 55 User Codes............................................................................................... 62 How To Set User Code Mode (# 120)......................................................... 62 How To Use User Code Mode .................................................................... 63 How To Check The User Code Counter (# 121)......................................... 63 How To Clear The User Code Counter (# 122)........................................... 64 How To Check The Total Number Of Masters And Prints Made Under All User Codes (# 123) ............................................................................................. 65 How To Clear The User Code Total Counter (# 124).................................. 66 4.REPLENISHING SUPPLIES Loading Paper On The Paper Feed Table ............................................. 69 Replenishing Paper..................................................................................... 69 Changing The Paper Size........................................................................... 70 When The Add Ink Indicator (j) Blinks................................................ 71 Master Roll Replacement ....................................................................... 74 Placing A New Roll Of Tape In The Tape Dispenser (Option) ............. 76 5.WHAT TO DO IF SOMETHING GOES WRONG If Your Machine Does Not Operate As You Want ................................. 79

“x” +“ORIGINAL JAM. REMOVE ORIGINAL” ........................................... 82 “x” + “PAPER FEED JAM. REMOVE JAMMED PAPER” ......................... 85 “x” + “MASTER FEED JAM. REMOVE JAMMED MASTER”.................... 88 “x” + “PAPER WRAP JAM. REMOVE JAMMED PAPER” ........................ 89 “x” + “MASTER EJECT JAM. REMOVE JAMMED MASTER”.................. 92 “x” + “DELIVERY JAM. REMOVE JAMMED PAPER” .............................. 94 When The Open Cover/Unit Indicator (M) Blinks................................. 95 When The Master Eject Indicator (k) Blinks........................................ 97 When Other Indicators Blink .................................................................. 98 When The Prints Are Thrown Over The Paper Delivery Table ............ 99 Poor Printing.......................................................................................... 100 Dirt On The Back Side Of Paper............................................................... 100 Dirt On The Front Side Of Paper (Black Line/Stain) ................................. 102 White Prints Or Incomplete Prints............................................................. 102 6.REMARKS Operation Notes..................................................................................... 105 General Cautions ...................................................................................... 105 Print Paper ................................................................................................ 107 Originals.................................................................................................... 107 Where To Put Your Machine................................................................. 109 Environmental Conditions ......................................................................... 109 Power connection...................................................................................... 110 Access to machine.................................................................................... 111 Maintaining Your Machine.................................................................... 112 Main Frame............................................................................................... 112 Optional Document Feeder....................................................................... 113 Combination Chart ................................................................................ 114 7.SPECIFICATION Main Frame............................................................................................. 115 30 Originals Document Feeder............................................................. 118 Consumables......................................................................................... 119 INDEX...................................................................................................... 120

• Paper smaller than 90 mm × 148 mm, 3.6" × 5.9" • Paper larger than 268 mm × 388 mm, 10.5" ×15.2" • Paper heavier than 157.0 g/m2, 41.7 lb • Paper lighter than 47.1 g/m2, 12.5 lb • Roughly-cut paper • Paper of different thickness in the same stack • Buckled or curled paper • Low stiffness paper Correct curls in the paper before setting it in the machine. When you cannot cor- rect the paper curl, stack the paper with the curl face down. Otherwise the paper might wrap around the drum or stains might appear. Store paper where it will not curl or absorb moisture. Use paper soon after it is unpacked. Only use paper where the leading edge has two right angle corners, as shown below. GRPRIN0E

• Maximum size: 257 × 364 mm, 10.2" × 14.4" • Maximum total thickness: 30 mm, 1.1" • Maximum total weight: 5 kg, 11.0 lb Ì If you use paste-up originals, make sure the pasted parts hold firmly to the base sheet and press the {Paste Shadow Erase} key. If the thickness of the paste- up original is more than 0.1 mm and the space between the pasted parts is less than 2 mm, 0.08", a shadow might appear on the prints. Ì If you use originals that have bold letters or solid images at the leading edges, you might get prints with dirty edges. In this case, insert the widest margin first, or raise the printing speed. Ì The first 5 mm, 0.2" of the leading edge cannot be printed. Make sure the lead- ing edge margin is at least 5 mm, 0.2". Ì a: 5 mm, 0.2" Original Print a

3 1 Preparation For Printing Loading Paper A Carefully open the paper feed ta- ble. B Put the paper feed side plates lock lever. Adjust the side plates to match the paper size. 1: Paper Feed Side Plates Lock Le- ver C Place the paper on the paper feed table. Note Ì Correct the paper curl before setting the paper. If you cannot do so, stack the paper with the curl face down as shown. TSLH026E TSLH01AE 1 TSLY013E GRMARU0E GRBATS0E

side plates touch the paper light- ly. Put back the lock lever. Setting Up The Paper Delivery Table A Open the paper delivery table. Reference When the prints are not deliv- ered in a neat stack, see ⇒ P.99 “When The Prints Are Thrown Over The Paper Delivery Table”. B Lift the paper delivery side plates and adjust them to the paper size. C Lift the paper delivery end plate and move it to match the print pa- per size. D Turn on the main switch. TSLY015E TSLH01YE 2 1 2 1 TSLH030E 2 1 TSLH01ZE TSLH01RE On Off On Off

is used as opposed to “Copying” in order to distinguish between the pro- cess that your machine uses to make prints, and the process used by a stan- dard copier machine. A standard copier scans in the origi- nal for each copy set made. This ma- chine, however, scans in your original once and makes multiple prints from this master. This chapter describes the basic pointing operations that your ma- chine is capable of. A Lift the platen cover. B Set the original face down on the exposure glass. The original should be centered according to the size marks on the right scale. C Lower the platen cover. D Press the {{{{Start}}}} key. A trial print is delivered to the pa- per delivery table. TSLH01BE TSLH010E TSLY01CE TSLS012N

the image density and the image position of the proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys or the fine adjust- ment dial. See ⇒ P.8 “Adjusting The Print Image Position”. Ì If the image density is slightly dark or light, adjust the image density using the {W} or {V} key. See ⇒ P.10 “Adjusting The Print Image Density”. F Enter the number of prints re- quired with the {{{{Number}}}} keys. Note Ì Up to 9999 prints can be entered at one time. Ì To change the number entered, press the {Clear/Stop} key and enter the new number. G Press the {{{{Print}}}} key. Note Ì After printing is completed, the same number of prints is auto- matically set for the next job. Ì To stop the machine during the multi-print run, press the {Clear/ Stop} key. Ì To return the machine to the ini- tial condition after printing, press the {Clear Modes} key. TSLS013N TSLS011N TSLS014N

7 1 Restoring Paper Feed And Paper Delivery Tables A Remove the paper from the paper feed table. The paper feed table will lower. B Turn off the main switch. C Close the paper feed table. D Move the end plate until the plate handle is flush with the end of the table. E Lower the end plate. F Move the side plates to the sides, then lower them. G Close the table. TSLY016E TSLH01RE On Off On Off TSLH020E TSLH021E TSLH01VE TSLH01ME 1 2 1 2

After master making, you can adjust the print image position to suit your needs. There are two ways: O OO O Shifting The Image Position Forward Or Backward Shift the image position using the {Image Position} keys. O OO O Shifting The Image Position To The Right Or Left Shift the image position using the side table fine adjusting dial. Shifting The Print Image Position Forward Or Backward * Paper feed direction A Press the left {{{{Image Position}}}} key to move the image forwards, the right key to move it backwards. Note Ì When you shift the image for- wards, leave a margin (more than 5 mm, 0.2") at the leading edge. If there is no margin, pa- per might wrap around the drum and cause a misfeed. Ì The right or left {Image Position} keys shift the image about 0.5 mm, 0.02" each time they are pressed. When the indicator changes, the image position shifts about 5 mm, 0.2". B Press the {{{{Proof}}}} key to check the image position. Shifting The Print Image Position To The Right Or Left * Paper feed direction GRFORW0E TSLS015N TSLS013N GRLEFT0E

9 1 A Turn the side table fine adjusting dial as shown in the illustrations. O OO O Shifting the image to the right O OO O Shifting the image to the left Note Ì The image position can be shift- ed up to about 10 mm, 0.4" each way. Each division on the scale is 2 mm, 0.08". B Adjust the paper delivery side plates to the print paper position. C Press the {{{{Proof}}}} key to check the image position. TSLH02IE TSLH02JE TSLS013N

You can adjust the print image densi- ty to suit your needs. There are two ways: O OO O Before Making A Master Adjust the image density using the {Image Density} key. O OO O After Making A Master Adjust the image density using the {W} or {V} key. Before Making A Master A Use the {{{{Image Density}}}} key before pressing the {{{{Start}}}} key. After Making A Master A Press the {{{{WWWW}}}} or {{{{VVVV}}}} key. To in- crease the speed, press the {{{{VVVV}}}} key. To reduce the speed, press the {{{{WWWW}}}} key. Note Ì The faster the printing speed be- comes, the lighter the printing density is. If you want darker prints, decrease the printing speed. TSLS016N TSLS017N

11 1 Tint Mode—Making Half-tone Prints Use the {Tint} key to make half-tone prints. A Press the {{{{Tint}}}} key to select Tint mode. B Set your originals on the exposure glass or in the optional document feeder. C Press the {{{{Start}}}} key. D Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Ad- justing The Print Image Position”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Position To The Right Or Left”). E Enter the number of prints with the {{{{Number}}}} keys. F Press the {{{{Print}}}} key. GRTINT0E TSLS018N TSLS012N TSLS014N

Use the {Fine} key to make clear prints. A Press the {{{{Fine}}}} key to select Fine mode. B Set your originals on the exposure glass or in the optional document feeder. C Press the {{{{Start}}}} key. Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Ad- justing The Print Image Position”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Position To The Right Or Left”). D Enter the number of prints with the {{{{Number}}}} keys. E Press the {{{{Print}}}} key. TSLS019N TSLS012N TSLS014N

13 1 Changing The Printing Speed Use the {W} or {V} key to adjust the speed of the machine with the image density and printing paper. A Press the {{{{VVVV}}}} key to increase the speed and press the {{{{WWWW}}}} key to re- duce the speed. Note Ì The following speeds are avail- able: • Setting 0: 80 sheets/minute • Setting 1: 100 sheets/minute • Setting 2: 120 sheets/minute Ì As a default setting, Setting 1 is selected. Ì The faster the printing speed be- comes, the lighter the printing density is, and vice versa. TSLS017N

print Run When You Want To Stop The Machine During The Multi- print Run And Print The Next Original A Press the {{{{Clear/Stop}}}} key. B Set the new original. C Enter the number of prints and press the {{{{Start}}}} key. When You Want To Change The Number Of Prints Entered Or Check The Completed Prints A Press the {{{{Clear/Stop}}}} key. B Change the number of prints or check the completed prints. Note Ì When you change the number of prints, you can re-enter the number with the {Number} keys after pressing the {Clear/Stop} key. C Press the {{{{Print}}}} key. TSLS01AN TSLS012N TSLS01AN TSLS014N

15 1 Preset Reduce/Enlarge—Reducing And Enlarging Using Preset Ratios You can select a preset ratio for print- ing. Note Ì The center and the leading edge of the print image do not shift when a print image is made with this func- tion. a: Paper Feed Direction b: Constant Ì You can select one of 7 preset ratios (3 enlargement ratios, 4 reduction ratios). Ì You can select a ratio regardless of the size of an original or printing paper. With some ratios, parts of the image might not be printed or margins will appear on prints. Ì Prints can be reduced or enlarged as follows: O OO O Reduction (Metric version) *1 Select this ratio when you make prints with a lot of edge margins. O OO O Reduction (Inch version) *1 Select this ratio when you make prints with a lot of edge margins. GRREDU0E GRENLA0E GRFULLOE a b Reduction Ratio Original Size Print Size 93 % *1 87 % A5 B6 A4 B5 82 % B4 A4 B5 A5 71 % A4 A5 B4 B5 Reduction Ratio Original Size Print Size 93 % *1 77 % 81/2"×14" 81/2"×11" 74 % 10"×14" 81/2"×11" 65 % 81/2"×11" 51/2"×81/2"

O OO O Enlargement (Inch version) A Select the desired reduction or en- largement ratio using the {{{{Re- duce}}}} key or the {{{{Enlarge}}}} key. B Make sure that the original and the print paper are the correct size. C Set your originals on the exposure glass or in the optional document feeder. D Press the {{{{Start}}}} key. E Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). F Make your prints. Enlarge- ment Ratio Original Size Print Size 141 % B5 B4 A5 A4 122 % A4 B4 A5 B5 115 % B5 A4 B6 A5 Enlarge- ment Ratio Original Size Print Size 155 % 51/2"×81/2" 81/2"×14" 129 % 51/2"×81/2" 81/2"×11" 121 % 81/2"×11" 11"×15" TSLS01BN TSLS012N

17 1 Center/Edge Erase—Erasing Center And Edge Margins When printing from thick books, or similar originals, the binding margin at the center and the edges might ap- pear on prints. To prevent this, follow the steps below. Note Ì As a default setting, the paper sizes and directions that can be used are as follows: Ì If you want to use other size origi- nals, you can register the size using Service Program mode (See ⇒ P.55 “Service Program Menu”). Ì The margin width to be erased can be adjusted with Service Program mode (See ⇒ P.55 “Service Program Menu”). A Press the {{{{Center/Edge Erase}}}} key twice to select the Center/Edge Erase mode. Check Indicator is blinking and is shown in the guidance dis- play. Note Ì To cancel this mode, press the {Center/Edge Erase} key again. B Press the {{{{ }}}} or {{{{ }}}} key to se- lect the paper size and direction. Metric version B4L, A4L, A5K, A5L, B5K, B5L Inch version 81/2" × 14"L, 81/2" × 11"L, 51/2" × 81/2"L, 51/2" × 81/2"K GRMARG0E TSLS01CN TSLS01DN

size and direction, press the {{{{#}}}} key. D Set the book on the exposure glass. E Press the {{{{Start}}}} key. F Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Ad- justing The Print Image Position”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Position To The Right Or Left”). G Enter the number of prints with the {{{{Number}}}} keys. H Press the {{{{Print}}}} key. TSLS01TN TSLH014E TSLS012N TSLS014N

19 1 Edge Erase—Erasing Edge Margins If you want to erase edge margins of a book original, follow the steps below. Note Ì As a default setting, the paper sizes and directions that can be used are as follows: Ì If you want to use other size origi- nals, you can register the size using Service Program mode (See ⇒ P.55 “Service Program Menu”). Ì The margin width to be erased can be adjusted with Service Program mode (See ⇒ P.55 “Service Program Menu”). A Press the {{{{Center/Edge Erase}}}} key to select Edge Erase mode. Check Indicator is blinking and is shown in the guidance dis- play. Note Ì To cancel this mode, press the {Center/Edge Erase} key twice. B Press the {{{{ }}}} or {{{{ }}}} key to se- lect the paper size and direction. C When you reach the desired paper size and direction, press the {{{{#}}}} key. D Set the book on the exposure glass. Metric version B4L, A4L, A5K, A5L, B5K, B5L Inch version 81/2"× 14"L, 81/2"× 11"L, 51/2"×81/2"L, 51/2"× 81/2"K TSLS01CN TSLS01DN TSLS01TN TSLH014E

F Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Ad- justing The Print Image Position”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Position To The Right Or Left”). G Enter the number of prints with the {{{{Number}}}} keys. H Press the {{{{Print}}}} key. TSLS012N TSLS014N

21 1 Paste Shadow Erase—Erasing The Shadow Of Pasted Originals If you want to erase the shadow of pasted originals, follow the steps be- low. A Set the original on the exposure glass. B Press the {{{{Paste Shadow Erase}}}} key. C Press the {{{{Start}}}} key. D Enter the number of prints with the {{{{Number}}}} keys. E Press the {{{{Print}}}} key. TSLH010E TSLS01PN TSLS012N TSLS014N

When you make prints on thick (127.9 to 157.0 g/m2, 34.0 to 41.7 lb) or thin (47.1 to 81.4 g/m2, 12.5 to 21.6 lb) pa- per, perform the following steps. Printing On Thick Paper A When you use paper heavier than 127.9 g/m2, 34.0 lb and lighter than 157.0 g/m2, 41.7 lb, position pres- sure lever to the Thick paper posi- tion. Note Ì When you use paper heavier than 64 g/m2, 17 lb and lighter than 157.0 g/m2, 41.7 lb, posi- tion the pressure lever to the standard position. Ì In the case of paper smaller than B5, 51/2" × 81/2" and heavier than 81.4 g/m2 (21.6 lb), move the feed roller pressure lever to the Thin paper position. Printing On Thin Paper A Set the side pads (move the side pad levers to as shown). B Position pressure lever to the Standard paper position. TSLH01CE TSLH02KE TSLH01CE

23 1 Selecting Original Type Select one of the following three types to match your originals: O OO O Photo mode Delicate tones of photographs and pictures can be reproduced with this mode. O OO O Letter mode Select this mode when your origi- nals contain only letters (no pic- tures). O OO O Letter/Photo mode Select this mode when your origi- nals contain photographs or pic- tures with letters. Note Ì Moire patterns might occur when screened originals are printed. Ì When using Photo mode to print originals with both letter and pho- tographs, the letter will appear lighter. To avoid this, select Let- ter/Photo mode with the {Type of Original} key. A Press the {{{{Type of Original}}}} key to select Photo mode. B Press the {{{{Image Density}}}} key to adjust the image density. C Set your originals on the exposure glass or in the optional document feeder. D Press the {{{{Start}}}} key. E Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). F Make your prints. TSLS01EN TSLS016N TSLS012N

When you want to save ink, select Economy mode. Note Ì Prints will come out lighter. A Press the {{{{Economy}}}} key. B Set your originals on the exposure glass or in the optional document feeder. C Press the {{{{Start}}}} key. D Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). E Make your prints. TSLS01FN TSLS012N

25 1 Auto Cycle—Printing From Several Originals At Once Use the {Auto Cycle} key to process masters and make prints at one stroke. Note Ì When you use the optional docu- ment feeder, it is not necessary to place originals one by one. All originals are fed and prints are completed after you press the {Print} key. Ì If you use the optional tape dis- penser, the tape dispenser drops a strip of paper onto the top of the paper stack after the last page of each printing set is fed out to the paper delivery table. This marks the end of each printing group. A Set the original on the exposure glass or in the optional document feeder. Note Ì You can set up to 30 originals into the optional document feeder. B Enter the number of prints re- quired with the {{{{Number}}}} keys. C Press the {{{{Start}}}} key. D Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). E Press the {{{{Auto Cycle}}}} key. Note Ì If you press the {Auto Cycle} key, you cannot make proof prints by pressing the {Proof} key. TSLS011N TSLS012N TSLS01GN

penser, turn on the tape dispenser power switch. G Press the {{{{Print}}}} key. Note Ì Repeat steps A through C until all originals are printed when you set originals on the expo- sure glass. Ì If you set originals into the op- tional document feeder, origi- nals are fed and prints are completed automatically. Ì After the last page of each set is fed out to the paper delivery ta- ble, the optional tape dispenser drops a strip of paper on the top of the paper stack. The next cy- cle begins. TSLP013E On Off

27 1 Class Mode—Group Printing From The Same Original Use the {Memory/Class} key to make sets of prints from the same original. The same number of prints is made for each set. Note Ì The optional tape dispenser auto- matically feeds out strips of paper which separate the printing groups on the paper delivery table. Ì Up to 20 sets of prints can be select- ed for one original. A Press the {{{{Memory/Class}}}} key to light the Class indicator. B With the {{{{Number}}}} keys, enter the number of prints for each set to be made from the original. C Press the {{{{#}}}} key. D With the {{{{Number}}}} keys, enter the desired number of sets. Note Ì The maximum number of sets that can be made is 20. GRCLAS0E R R R R R R R TSLS01XN TSLS011N TSLS01TN TSLS011N

penser power switch. F Set one original face down on the exposure glass or in the optional document feeder. G Press the {{{{Start}}}} key. H Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). I Make your prints. Note Ì After the last page of each print- ing set is fed out to the paper de- livery table, the tape dispenser drops a strip of paper on the top of the paper stack. Ì If the power switch of the op- tional tape dispenser is turned off or the tape dispenser is not installed in your machine, the group printing cycle stops after each set is delivered. Remove the set of prints from the paper delivery table and press the {Print} key to start the next group printing cycle. TSLP013E On Off TSLS012N TSLS014N

29 1 Memory Mode—Group Printing From Different Originals Use the {Memory/Class} key to make sets of prints from different originals. Note Ì With the optional document feed- er, you can set several originals and make prints of all of them at once. See ⇒ P.45 “Memory Mode With The Document Feeder”. Ì The optional tape dispenser auto- matically feeds out strips of paper which separate the printing groups on the paper delivery table. A Press the {{{{Memory/Class}}}} key to light the Memory indicator. B With the {{{{Number}}}} keys, enter the desired number of prints for the first original. C Press the {{{{#}}}} key. This stores the number of prints to be made for the first original in memory 1. Note Ì When the number of prints in each set is the same, it is not nec- essary to input the number of prints for each group in memo- ry. Simply select Auto Cycle mode and enter the desired number of prints once. D C B GRCLAS1E A A B C D TSLS01WN TSLS011N TSLS01TN

number of prints for the second original. E Press the {{{{#}}}} key. This stores the number of prints to be made for the second original in memory 2. Note Ì Repeat steps D and E for each original. Ì The number of prints for up to 20 originals can be stored. F Press the {{{{#}}}} key again. The memory returns to memory 1. Note Ì If you store the number of prints for 20 originals, the memory number returns to 1. It is not necessary to press the {#} key. G Set the first original face down on the exposure glass. Note Ì Set originals one sheet at a time in the same order that you stored them in memory. H Press the {{{{Start}}}} key. I Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). TSLS011N TSLS01TN TSLH010E TSLS012N

31 1 J Turn on the optional tape dis- penser power switch. K Press the {{{{Auto Cycle}}}} key. Note Ì If you press the {Auto Cycle} key, you cannot make proof prints by pressing the {Proof} key. L Press the {{{{Print}}}} key. Note Ì After the first set is fed to the pa- per delivery table, the optional tape dispenser drops a strip of paper on the top of the paper stack. M After the first set is completed, set the second original on the expo- sure glass and press the {{{{Start}}}} key. Note Ì Repeat this step until you have finished printing. TSLP013E On Off TSLS01GN TSLS014N TSLS012N

Into One Print As a default, this function cannot be used. If you want to use this function, set “SET COMBINE KEY” to “Yes”. See “SET COMBINE KEY” in ⇒ P.55 “Service Program Menu”. You can print 2 separate originals on a single sheet of paper. The following tables list the combinations that can be used when combining two origi- nals. Note Ì The following tables list the combi- nations that can be used in this function: O OO O Metric version O OO O Inch version Ì If the master length of the first original is longer than the maxi- mum allowable length or shorter than the minimum allowable length, Combine Copies mode is canceled. The following table gives the maximum and minimum al- lowable master length. Ì Master length = actual original length × Enlargement/Reduction ratio Ì Any image closer than 5 mm, 0.2" to the leading edge of the first orig- inal will not be printed. Also, any image closer than 4 mm, 0.16" to the leading edge of the second original will not be printed. When the image is too close to the leading edge, use copies of the originals with the image shifted at least 5 mm, 0.2" for the first original (4 Original Size A4 K B5 K A5 K B6 K A6 K Pa- per Size B4 L 87 % 100 % 122 % 141 % -- A4 L 71 % 82 % 100 % 115 % 141 % B5 L 61 % 71 % 87 % 100 % 122 % A5 L -- -- 71 % 82 % 100 % GRCOMB0E 2 1 1 2 Original Size 81/2" × 11"K 51/2" × 81/2"K Paper Size 81/2" × 14"L 77 % 100 % 81/2" × 11"L 65 % 100 % 51/2" × 81/2"L -- 65 % Minimum Maximum LG drum model 91 mm, 3.6" 243 mm, 9.5" B4 drum model 91 mm, 3.6" 243 mm, 9.5"

33 1 mm, 0.16" for the second original) from the leading edge. Ì You can select different kinds of image settings for the first and sec- ond original. Ì Make sure that the paper feed side plates touch the paper lightly when in the Combine Copies func- tion. Otherwise, the two original images will not appear at the prop- er position on the prints. Reference When you use the optional docu- ment feeder with this function, see ⇒ P.29 “Memory Mode—Group Printing From Different Originals”. A Set the first original face down. Note Ì The first original will be printed on the leading part of the print. B Press the {{{{Center/Edge Erase}}}} key twice. C Press the {{{{ }}}} or {{{{ }}}} key to se- lect the original size and direc- tion. D When you reach the desired size and direction, press the {{{{#}}}} key. E Press the {{{{Combine Copies}}}} key to select your desired mode. TSLY01AE TSLS01CN TSLS01DN TSLS01TN TSLS01JN

G The beeper sounds after the first original is on the master. Set the second original face down. H Press the {{{{Start}}}} key. I Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). J Enter the number of prints with the {{{{Number}}}} keys. K Make your prints. TSLS012N TSLS012N TSLS011N

35 1 Skip Feed Printing If the backs of prints are dirty, you can increase the time between two prints using the {Skip Feed} key. In the default setting, when one sheet of paper is fed the drum rotates twice. However, you can select the number of rotations of the drum. This gives you the chance to remove prints one by one from the paper delivery table or insert one sheet of paper between two prints. A Set your originals on the exposure glass or in the optional document feeder. B While holding down the {{{{Skip Feed}}}} key, select the number of rotations of the drum while one sheet of paper is fed with the {{{{Number}}}} keys. Note Ì You can select from 1 to 9 rota- tions. Ì The beeper sounds after you set the number of rotations. C Press the {{{{Start}}}} key. D Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). E Enter the number of prints with the {Number} keys. F Make your prints. TSLS01YN TSLS012N TSLS011N

Memory You can store up to 9 frequently used print job settings in machine memory, and recall them for future use. Note Ì The stored programs are not cleared when you turn off the main switch. Ì The stored programs cannot be de- leted. If you want to change a stored program, overwrite it. Storing Your Settings A Set the print settings you want to put into memory. B Press the {{{{Program}}}} key. Numbers already containing a program are displayed on the guidance display. C Enter “0” with the {{{{Number}}}} keys. D Press the {{{{#}}}} key. Note Ì The program numbers (1 to 9) will be displayed in the guid- ance display. Ì If a user program has been pro- tected, that program number will not appear in the display. For how to change a protected user program, see ⇒ P.38 “Pro- tecting A Program”. Ì If all the user programs have been protected, the machine re- turns to the ready condition. TSLS01KN TSLS011N TSLS01TN

37 1 E Select the program number you want to store the settings in with the {{{{Number}}}} keys. Note Ì Make sure that the previous job settings stored under the select- ed program number are over- written. F Press the {{{{#}}}} key. Recalling A Program A Press the {{{{Program}}}} key. Note Ì Numbers already containing a program are displayed on the guidance display. B Select the program number you want to recall with the {{{{Number}}}} keys. C Press the {{{{#}}}} key. Note Ì The stored settings are recalled. D Set your originals on the exposure glass or in the optional document feeder. TSLS011N TSLS01TN TSLS01KN TSLS011N TSLS01TN

Protecting A Program If you want to prevent someone from writing over your program, do the following procedure. A While holding down the {{{{Clear/ Stop}}}} key, press the {{{{Program}}}} key. B Enter “1” with the {{{{Number}}}} keys. C Press the {{{{#}}}} key. Note Ì The numbers of the programs which are not protected will be displayed in the guidance dis- play. D Select the program number you want to protect with the {{{{Number}}}} keys. E Press the {{{{#}}}} key. TSLS012N TSLS01RN TSLS01LN TSLS01TN TSLS011N TSLS01TN

39 1 Removing Program Protection A While holding down the {{{{Clear/ Stop}}}} key, press the {{{{Program}}}} key. B Enter “0” with the {{{{Number}}}} keys. C Press the {{{{#}}}} key. Note Ì If no program number is pro- tected, the machine returns to the ready condition. D Select the program number you want to remove protection from with the {{{{Number}}}} keys. E Press the {{{{#}}}} key. TSLS01RN TSLS01MN TSLS01TN TSLS011N TSLS01TN

Documents This function prevents others from making prints of secret documents from the master. For example, if you want to print some documents with sensitive information, use this func- tion after making your prints so that nobody can access that master again. A Make your prints. B Hold down the {{{{Security}}}} key for at least 5 seconds. Note Ì If you press the {Proof} key or the {Print} key after setting Se- curity mode, the beeper sounds and you cannot make prints. Ì You cannot cancel Security mode even if you turn off the main switch. Ì If you make the next master, Se- curity mode is canceled. TSLS01NN

Printing Using The Optional 30 Originals Document Feeder Insert a stack of originals in the document feeder. They will be fed automatically. Document Feeder Exterior 1. Original Tray Original used to make masters are deliv- ered to this tray. 2. ADF Unit Feeds the original to the master making position. 3. Original Guides Adjust these guides to position the origi- nals correctly. 4. ADF Unit Open Lever Use to open the ADF unit. Originals Setting the following originals in the document feeder might cause original mis- feeds or damage to the originals. Set these originals on the exposure glass. • Originals heavier than 90 g/m2, 23.9 lb (when setting a stack of originals) • Originals lighter than 50 g/m2, 13.3 lb (when setting a stack of originals) • Originals heavier than 120 g/m2, 31.9 lb (when setting one original at a time) • Originals lighter than 40 g/m2, 10.6 lb (when setting one original at a time) • Carbon coated originals • Damaged originals TSLP018E 1 2 3 4

• Originals perforated for ring binders • Book originals • Originals written with a pencil or ball-point pen • Originals smaller than 148 mm × 105 mm, 5.8" × 4.1" • Originals larger than 257 mm × 364 mm, 10.2" × 14.4" • Folded, curled, creased originals • Bound, stapled, or clipped originals • OHP transparencies • Translucent paper • Pasted originals Note Ì If you use paste-up originals, make sure the pasted parts hold firmly to the base sheet and press the {Paste Shadow Erase} key. If the thickness of the paste- up original is more than 0.1 mm, and the space between the pasted parts is less than 2 mm, 0.08", a shadow might appear on the prints. Ì The first 5 mm, 0.2", of the leading edge cannot be printed. Make sure the leading edge margin is at least 5 mm, 0.2". Ì a: 5 mm, 0.2" Setting Originals In The Document Feeder Note Ì If you set one original into the document feeder while another original is still on the exposure glass, the original set into the document feeder will be scanned first. Original Print a

43 2 A Adjust the guide to the original size. B Insert the aligned originals face up in the document feeder until they stop. Limitation Ì Approximately 30 originals (64 g/m2, 17 lb) can be inserted at one time in the 30 originals document feeder. The first (top) original will be fed first. Note Ì Do not insert different size originals at the same time. Ì The guides must fit snugly against both sides of the stack. C Set the desired settings and press the {{{{Start}}}} key. D Make your prints. TSLH011E TSLH012E TSLS012N

stops, that original is fed automatically and a trial print is delivered to the paper delivery table after the print of the first original is completed. Check the image position of the trial print of the next original. If necessary, make proof prints using the {Proof} key to check the image position again. Combine Copies With The Document Feeder As a default, this function cannot be used. If you want to use this function, set “SET COMBINE KEY” to “Yes”. See “SET COMBINE KEY” in ⇒ P.55 “Service Program Menu”. A Insert the 2 originals face up, tops pointing towards the operation side. Note Ì When you use the optional 30 originals document feeder, the bottom orig- inal will be printed on the leading part of print. B Check the print paper size and the reproduction ratio. C Press the {{{{Combine Copies}}}} key to select your desired mode. TSLH013E TSLS01JN

45 2 D Press the {{{{Start}}}} key. E Check the image position of the trial or proof print. Note Ì If the image position is not correct, adjust it using the {Image Position} keys (see ⇒ P.8 “Shifting The Print Image Position Forward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Position To The Right Or Left”). Ì After the first original is on the master, the second original is fed. Ì If you set only one original, the beeper sounds after the first original is on the master. Set the second original and the desired image settings. Then, press the {Start} key. F Enter the number of prints with the {{{{Number}}}} keys. G Make your prints. Memory Mode With The Document Feeder Note Ì To prevent original misfeeds, do not set originals of different sizes. Ì Do not set more than 30 originals at one time in the optional 30 originals doc- ument feeder. TSLS012N TSLS011N

B With the {{{{Number}}}} keys, enter the desired number of prints for the first original. C Press the {{{{#}}}} key. This stores the number of prints to be made for the first original in memory 1. Note Ì When the number of prints in each set is the same, it is not necessary to in- put the number of prints for each group in memory. Simply select Auto Cycle mode and enter the desired number of prints once. TSLS01WN TSLS011N TSLS01TN

47 2 D Set your originals face up into the document feeder. Note Ì When you use the optional 30 originals document feeder, the originals are fed from the bottom of the stack. Make sure that the originals are set in the correct sequence with the first original on the bottom. E Press the {{{{Start}}}} key. F Check the image position of the trial or proof print. Note Ì If the image position is not correct, adjust it using the {Image Position} keys (see ⇒ P.8 “Shifting The Print Image Position Forward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Position To The Right Or Left”). TSLH013E TSLS012N

H Press the {{{{Auto Cycle}}}} key. Note Ì In Auto Cycle mode, printing starts automatically after a trial print is de- livered. I Press the {{{{Print}}}} key. Note Ì After the last page of each set is fed out to the paper delivery table, the tape dispenser drops a strip of paper on the top of the paper stack. The next cy- cle begins. TSLP013E On Off TSLS01GN TSLS014N

49 2 Color Printing Using The Optional Color Drum Color drum units (red, blue, green, brown, yellow, purple, navy, ma- roon, orange, teal and gray) are avail- able as options in addition to the standard black unit. For making color prints, a separate drum unit is neces- sary for each color. Making Color Prints A Make sure that the COLOR is shown in the guidance display. B Press the {{{{Start}}}} key. C Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). D Make your prints. Changing The Color Drum Unit A Open the front door. B Lift the lock lever until it locks in position. GRCOPR0E TSLS012N TSLH01IE TSLH01KE

Note Ì If you cannot pull out the drum unit, push the drum unit han- dle, then pull out the drum unit. D Hold the rail on the drum and slide out the drum while pulling the release towards you. E Remove the drum unit from the machine while holding the upper drum stay. Note Ì Be careful not to let the drum unit fall. F Insert the color drum unit along the guide rail. G Slide in the drum unit until it locks in position. H Lower the drum unit lock lever. TSLH01LE TSLH01FE TSLH01GE TSLH01PE TSLH01HE TSLH027E

51 2 I Close the front door. Note Ì Make sure that the Cover Open indicator (M) turns off, and the COLOR is shown in the guid- ance display. Printing In Two Colors After printing in one color, you can print in another color on the same side of the print. Important Ì Leave the prints for a while before printing on them again to let the ink dry. Ì If the prints are not dry, the paper feed roller might become dirty. In this case, wipe off the roller with a cloth. Note Ì You cannot print in two colors at one time. A Prepare the two originals. Set the first original on the exposure glass. B Press the {{{{Start}}}} key. C Check the image position of the trial or proof print. Note Ì If the image position is not cor- rect, adjust it using the {Image Position} keys (see ⇒ P.8 “Shift- ing The Print Image Position For- ward Or Backward”) or the side table fine adjusting dial (see ⇒ P.8 “Shifting The Print Image Po- sition To The Right Or Left”). D Enter the number of prints with the {{{{Number}}}} keys. GRPREP0E TSLS012N TSLS011N

F Remove the prints from the paper delivery table and set them on the paper feed table again as shown in the illustration. G Exchange the drum unit. See ⇒ P.49 “Changing The Color Drum Unit”. H Set the second original and press the {{{{Start}}}} key. I Check the image position. J Press the {{{{Print}}}} key. TSLS014N TSLY019E TSLH01QE TSLS012N

Accessing Service Programs The service programs can be set by following this procedure. Reference For the service program menu, see ⇒ P.55 “Service Program Menu”. A Press the {{{{Clear Modes}}}} key. B Hold down the {{{{Clear/Stop}}}} key for at least 3 seconds. The SP-mode display appears on the guidance display. Note Ì If you press the wrong key, try pressing the above keys from the beginning. C With the {{{{Number}}}} keys, enter the desired service program number (SP No.). Reference For the SP No., see ⇒ P.55 “Ser- vice Program Menu”. When you want to leave the service program mode A Press the {{{{Clear Modes}}}} key. Reference If you want to change the set- tings of a selected service program, see ⇒ P.54 “Chang- ing The Settings Of Service Programs”. TSLS01UN TSLS01AN TSLS011N TSLS01UN

54 3 Changing The Settings Of Service Programs A After entering the desired SP No., press the {{{{#}}}} key. The value or mode set at the factory will be displayed at the end of the second line on the guidance display. Note Ì If you designate the wrong SP No., press the {Clear Modes} key. Then, re- enter the desired SP No. B Enter the desired value or mode with the {{{{Number}}}} keys. C Press the {{{{#}}}} key to store the desired value or mode. TSLS01TN TSLS011N TSLS01TN

55 3 Note Ì If you enter the wrong value or mode, press the {Clear Modes} key. Then, go back to step A. When you want to leave the service program mode A Press the {{{{Clear Modes}}}} key. Service Program Menu SP No. Mode Function 5 TAPE MARKER OFF Specifies whether the optional tape dispenser can be used. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes 10 MIN PRINT Specifies the minimum number of prints that can be input with the {Number} keys. Note Ì Default: 0 Ì Adjustment value: 0 to 9999 11 MAX PRINT Specifies the maximum number of prints that can be input with the {Number} keys. Note Ì Default: 0 Ì Adjustment value: 0 to 9999 TSLS01UN

56 3 12 SET DISPLAY If you want to change the language used by the guidance display, select the language version. Note Ì Default: 1 Ì Adjustable value: • 0: Japanese • 1: English • 2: German • 3: French • 4: Italian • 5: Spanish • 6: Chinese • 7: Dutch • 8: Portuguese (BRAZIL) 13 SET SIZE MODE Change the size mode. Note Ì Default: 0 Ì Adjustment value: 0: mm 1: Inch 17 SET COMBINE KEY If you want to use Combine Copies mode, select "Yes". Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes Ì For details about Combine Copies, See ⇒ P.32 “Combine Copies—Combining 2 Originals Into One Print”. 20 BUZZER ON Turns the buzzer ON or OFF. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes SP No. Mode Function

57 3 21 PRINTS/MASTER COST The optional key counter usually counts the num- ber of prints made regardless of the number of masters used. For accounting purposes, it is possi- ble for the key counter to be incremented by a val- ue between 0 and 50 whenever a new master is used. Example: The key counter is adjusted to increase by 20 for each master fed. If 100 copies have been made and the master is replaced, the key counter will increase by 120. Note Ì Default: 0 Ì Adjustment value: 0 – 50 25 CLEAR 2 IN 1 By default, when master making is finished in Combine Copies mode, this mode stays selected for the next master making. If you want master making turned off, select “1”. Note Ì Default: 0 Ì Adjustable value: 0: No 1: Yes Ì Even if you select “1” in this mode, Combine Copies mode is not cleared when the next orig- inal are set in the optional document feeder. Ì For details about Combine Copies, See ⇒ P.32 “Combine Copies—Combining 2 Originals Into One Print”. 29 PHT BCKGRND COR- RECT When you make prints in Photo or Letter/Photo mode, the background of the prints might become dirty. You can prevent this using this function. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes 40 ORIGINAL Specifies the image mode at power on. Note Ì Default: 0 Ì Adjustment value: • 0: Letter mode • 1: Letter/Photo mode • 2: Photo mode SP No. Mode Function

58 3 41 IMAGE DENSITY Specifies the image density at power on. Note Ì Default: 1 Ì Adjustment value: • 0: Light • 1: Standard • 2: Dark • 3: Darker 42 PRINT SPEED Specifies the printing speed at power on. Note Ì Default: 1 Ì Adjustment value: • 0 : 80 sheets/minute • 1 : 100 sheets/minute • 2 : 120 sheets/minute 43 AUTO CYCLE MODE Specifies whether Auto Cycle mode is selected at power on. Note Ì Default: 1 Ì Adjustment value: 0: No 1: Yes 81 QUALITY START NO. You can select how many times Quality Start mode is carried out for each master making. When you set the Quality Start function, the bold letter or solid images might be light. Note Ì Default: 1 Ì Adjustment value: 0 to 3 times 82 SKIP FEED NO. When you use the Skip Feed Printing function, you can select how many times the drum rotates while one sheet of paper is fed. Note Ì Default: 2 times Ì Adjustment value: 1 to 9 times SP No. Mode Function

59 3 84 AUTO MULTI COPY If you set an original on the exposure glass and press the {Combine Copies} key and {Start} key, two identical images are printed on the one sheet. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes Ì For details about Combine Copies, see ⇒ P.32 “Combine Copies—Combining 2 Originals Into One Print”. 87 MEMORY PRINT If you wish to make print sets of a single page doc- ument placed on the exposure glass in Memory Mode, change this setting to Stack. Each print set or stack will contain the number of prints you pro- gram in Memory mode. If set to Memory, Memory mode will work. Note Ì Default: 0 Ì Adjustment value: 0: Memory 1: Stack Ì For details about Memory mode, see ⇒ P.29 “Memory Mode—Group Printing From Different Originals”. 88 AUTO MEMORY/ CLASS In this function, the machine stops printing for 2 seconds after one set of prints are completed in Memory mode and Class mode. This gives you the chance to separate each set when you do not have an optional tape dispenser. For example, you can remove prints one by one from the paper delivery table or insert one sheet of paper between the prints. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes 113 RESETTABLE COUNT Used to display the total number of masters and prints. • M: Total number of masters • P: Total number of prints SP No. Mode Function

60 3 114 CLR RESETTABLE COUNT Clears the resettable master/print counter. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes 120 USER CODE MODE Selects user code mode. When you set this func- tion, you have to also specify the auto reset time. For details about user code mode, see ⇒ P.62 “Us- er Codes”. Note Ì Default: • User Code mode:0 • Auto Reset time: 0 Ì Adjustment value: • User Code mode: 0: No 1: Yes • Auto Reset time: 0: No, 1 – 5 minutes UC COUNT Displays the number of masters and prints made in each user code. Note Ì M: Number of masters Ì P: Number of prints 122 CLR UC COUNT Clear each user code counter. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes 123 TOTAL UC COUNT Display the total number of masters and prints for all the 20 user codes. Note Ì M: Number of masters Ì P: Number of prints 124 CLEAR TOTAL UC COUNT Clear the total user code counter. Note Ì Default: 0 Ì Adjustment value: 0: No 1: Yes SP No. Mode Function

61 3 Entering decimal values in SP No. 160–162: • Press the {Program} key to enter a decimal point. • Press the {q} key to fix the value. 160 SIDE ERS. Adjust the default side edge margin width in Edge Erase and Center/Edge Erase mode. Note Ì Default: • Metric Version: 5 mm • Inch Version: 0.2" Ì Adjustable value: • Metric Version: 2 – 20 mm • Inch Version: 0.1" – 0.8" 161 CENTER ERS. Adjust the default center margin width in Center/ Edge Erase mode. Note Ì Default: • Metric version: 10 mm • Inch version: 0.4" Ì Adjustable value: • Metric version: 4 – 60 mm • Inch version: 0.2" – 2.3" 162 HORIZONTAL ERS. Adjust the default horizontal edge (top and bot- tom) margin in Edge Erase and Center/Edge Erase mode. Note Ì Default: • Metric version: 5 mm • Inch version: 0.2" Ì Adjustable value: • Metric version: 2 – 20 mm • Inch version: 0.1" – 0.8" SP No. Mode Function

62 3 User Codes If the machine is set to use the User Code function, operators must input their user codes before the machine can operate. The machine keeps count of the number of prints made under each user code. In this mode, the following 20 user codes (fixed) can be used to access the machine: 382, 191, 182, 173, 164, 155, 146, 137, 128, 119, 482, 291, 282, 273, 264, 255, 246, 237, 228, 219 Note Ì To prevent unauthorized users from accessing the machine, note down the codes and then black out the codes from this manual. How To Set User Code Mode (# 120) The following procedure explains how to set user code mode. This must be done before a user code can be in- put. A Press the {{{{Clear Modes}}}} key. B Hold down the {{{{Clear/Stop}}}} key for at least 3 seconds. C Enter “120” with the {{{{Number}}}} keys and press the {{{{#}}}} key. D Enter “1” (Yes) with the {{{{Number}}}} keys and then press the {{{{#}}}} key. E Specify the Auto Reset time. En- ter the desired setting with the {{{{Number}}}} keys and press the {{{{#}}}} TSLS01UN TSLS01AN TSLS011N TSLS01VN

leave Service Program mode. How To Use User Code Mode A Input your assigned 3-digit user code with the {{{{Number}}}} keys, then press the {{{{#}}}} key. B Make your prints. C After you have finished, press the {{{{Clear/Stop}}}} key while holding down the {{{{Clear Modes}}}} key. Note Ì This prevents others from mak- ing prints using your user code. Ì If you do not follow this step, the machine will not request the next user for their codes unless the auto reset time has expired. How To Check The User Code Counter (# 121) Reference If you want to check the total mas- ters and prints made under all user codes, see ⇒ P.65 “How To Check The Total Number Of Masters And Prints Made Under All User Codes (# 123)”. A Press the {{{{Clear Modes}}}} key. B Hold down the {{{{Clear/Stop}}}} key TSLS011N TSLS01UN TSLS011N TSLS01SN TSLS01UN

64 3 for at least 3 seconds. C Enter “121” with the {{{{Number}}}} keys and press the {{{{#}}}} key. The number of masters and prints made under the user code “382” will be displayed in the guidance display. D Keep pressing the {{{{#}}}} key to dis- play the number of masters and prints made under your user code. E Press the {{{{Clear Modes}}}} key to leave Service Program mode. How To Clear The User Code Counter (# 122) Reference If you want to clear every user code counter, see ⇒ P.66 “How To Clear The User Code Total Counter (# 124)”. A Press the {{{{Clear Modes}}}} key. TSLS01AN TSLS011N TSLS01TN TSLS01UN TSLS01UN

for at least 3 seconds. C Enter “122” with the {{{{Number}}}} keys and press the {{{{#}}}} key. D Keep pressing the {{{{#}}}} key until desired user code is displayed. E Enter “1” (Yes) with the {{{{Number}}}} keys and press the {{{{#}}}} key. F Press the {{{{Clear Modes}}}} key to leave Service Program mode. How To Check The Total Number Of Masters And Prints Made Under All User Codes (# 123) A Press the {{{{Clear Modes}}}} key. B Hold down the {{{{Clear/Stop}}}} key for at least 3 seconds. TSLS01AN TSLS011N TSLS01TN TSLS01VN TSLS01UN TSLS01AN

66 3 C Enter “123” with the {{{{Number}}}} keys and press the {{{{#}}}} key. The total number of masters and prints made under all user codes will be displayed in the guidance display. • M: Number of masters • P: Number of prints D Press the {{{{Clear Modes}}}} key to leave Service Program mode. How To Clear The User Code Total Counter (# 124) A Press the {{{{Clear Modes}}}} key. B Hold down the {{{{Clear/Stop}}}} key for at least 3 seconds. C Enter “124” with the {{{{Number}}}} keys and press the {{{{#}}}} key. TSLS011N TSLS01UN TSLS01UN TSLS01AN TSLS011N

keys and press the {{{{#}}}} key. E Press the {{{{Clear Modes}}}} key to leave Service Program mode. TSLS01VN TSLS01UN

Loading Paper On The Paper Feed Table The Load Paper indicator (B) blinks when the paper feed table runs out of paper. Replenishing Paper A Press the {{{{Clear/Stop}}}} key. Note Ì This step is necessary only if you want to pause a print run to replenish paper. B Press the {{{{Paper Feed Table Down}}}} key. Note Ì The paper feed table will lower without the key being pressed when the printing paper runs out. Ì The top sheet might remain be- tween the feed rollers. In this case, remove the top sheet. C Load paper on the paper feed ta- ble. TSLS01AN TSLH029E TSLY013E

ting the paper. D Press the {{{{Print}}}} key to resume printing. Changing The Paper Size A Remove the paper from the paper feed table. The paper feed tray will lower. B Put the paper feed side plates lock lever. Adjust the paper feed side plates to match the paper size. 1: Paper Feed Side Plates Lock Le- ver C Place the paper on the paper feed table. Note Ì Correct any paper curl before setting the paper. Ì Make sure that the side plates touch the paper lightly. Ì Put back the lock lever. D Adjust the side plates and the end plate. TSLS014N TSLY016E TSLH01AE 1 TSLY013E 2 1 2 1 TSLH030E

71 4 When The Add Ink Indicator (j) Blinks The Add Ink indicator (j) blinks when it is time to supply ink. R CAUTION: R CAUTION: R CAUTION: R CAUTION: A Open the front door. • If ink comes into contact with your eyes, rinse immediately in run- ning water. In the case of any abnormal symptoms, consult a doctor. • Keep the ink or ink container out of reach of children. • If ink is ingested, force vomiting by drinking a strong saline solu- tion and consult a doctor immediately. • This machine has been tested for safety using this supplier's parts and consumables. We recommend you only use these specified supplies. TSLH01IE

C Remove the cap of the new ink cartridge. D Insert the new cartridge into the ink holder. E Return the ink holder to its original position until it clicks. Note Ì Always supply ink of the same color. 1 2 TSLH01JE TSLT012E 1 2 TSLT013E

73 4 Ì Make sure to firmly insert the part indicated by the arrow mark into the guide. F Close the front door. The machine will start idling to supply ink to the drum. Note Ì It will stop when the correct amount of ink reaches the drum. TSLT011E

The Master End indicator (C) is lit when it is time to replace the master roll. A Open the original table. Note Ì Lift the original table release le- ver and lift the original table. B Open the right side cover. C Open the plotter cover. D Remove the used master roll and pull out both spools. Then, insert both spools into a new master roll. Note Ì When the Master End indicator lights, it is necessary to replace the master roll even if some master remains on the old roll. E The new master roll must be po- sitioned as shown in the illustra- tion. TSLH01SE TSLH01TE TSLH02EE TSLT010E TSLH01XE

75 4 F Set the paper edge of the master roll as shown. Note Ì Rotate the spools backward to take up any slack in the master. G Close the plotter cover. H Close the right side cover. I Return the original table to its original position. TSLH01UE TSLH023E TSLH02DE TSLH025E

Dispenser (Option) Note Ì Make sure that the main switch is turned on and the power switch of the tape dispenser is off. A Open the cover of the tape dis- penser. B As shown, put the roll in the dis- penser. Note Ì Make sure that the tape is in- stalled in the proper direction. If it is not in the correct direction, the tape dispenser will not work correctly. C Feed the leading edge of the roll in the dispensing slot until it stops. Note Ì Push the tape as far as possible through the slot. D Turn on the power switch of the tape dispenser. TSLP010E TSLP011E TSLP012E TSLP013E On Off

77 4 E Press the manual cut button to trim off the leading edge of the tape. TSLP014E

GOES WRONG If Your Machine Does Not Operate As You Want If a malfunction or a misfeed occurs within the machine, the following indicators will blink or light. O OO O When the misfeed indicator (x x x x) blinks Indicator Guidance Display Page x ORIGINAL JAM. REMOVE ORIGINAL REMOVE ORIGINAL ⇒ P.82 ““x” +“ORIGINAL JAM. REMOVE ORIGINAL”” x PAPER FEED JAM. REMOVE JAMMED PAPER REMOVE JAMMED PAPER ⇒ P.85 ““x” + “PAPER FEED JAM. RE- MOVE JAMMED PAPER”” x MASTER FEED JAM. RE- MOVE JAMMED MASTER REMOVE JAMMED MASTER ⇒ P.88 ““x” + “MASTER FEED JAM. RE- MOVE JAMMED MASTER”” x PAPER WRAP JAM. REMOVE JAMMED PAPER REMOVE JAMMED PAPER ⇒ P.89 ““x” + “PAPER WRAP JAM. RE- MOVE JAMMED PAPER”” x MASTER EJECT JAM. RE- MOVE JAMMED MASTER REMOVE JAMMED MASTER ⇒ P.92 ““x” + “MASTER EJECT JAM. RE- MOVE JAMMED MASTER”” x DELIVERY JAM. REMOVE JAMMED PAPER REMOVE JAMMED PAPER ⇒ P.94 ““x” + “DELIVERY JAM. RE- MOVE JAMMED PAPER”” TSLS020N