Getac V200 Operation & User’s Manual

All brand and product names are trademarks or registered trademarks of their respective companies. NOTE The information in this manual is subject to change without notice. Most screens and operating instructions in this manual are based on Windows 7. If you’re using a different version of Windows, the screens and related operations may not be the same. For the latest version of the manual, please visit the Getac website at www.getac.com.

consumers energy-efficient solutions, making it easy to save money while protecting the environment for future generations. Please reference ENERGY STAR® related information from www.energystar.gov. As an ENERGY STAR® Partner, Getac Technology Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. An ENERGY STAR® qualified computer uses 70 % less electricity than computers without enabled power management features. Earning the ENERGY STAR® z When every home office is powered by equipment that has earned the ENERGY STAR®, the change will keep over 289 billion pounds of greenhouse gases out of the air. z If left inactive, ENERGY STAR® qualified computers enter a low-power mode and may use 15 watts or less. New chip technologies make power management features more reliable, dependable, and user-friendly than even just a few years ago. z Spending a large portion of time in low-power mode not only saves energy, but helps equipment run cooler and last longer. z Businesses that use ENERGY STAR® enabled office equipment may realize additional savings on air conditioning and maintenance.

office (e.g., computer, monitor, printer, and fax) can save enough electricity to light an entire home for more than 4 years. z Power management (“sleep settings”) on computers and monitors can result in much savings annually. Remember, saving energy prevents pollution Because most computer equipment is left on 24 hours a day, power management features are important for saving energy and are an easy way to reduce air pollution. By using less energy, these products help lower consumers’ utility bills, and prevent greenhouse gas emissions.

Chapter 1 Getting Started ............................................................. 1-1 Getting the Computer Running ............................................. 1-2 Unpacking ........................................................................... 1-2 Connecting to AC Power .................................................... 1-3 Opening and Closing the Cover ........................................ 1-4 Operating in Tablet Mode ................................................. 1-5 Turning On and Off the Computer ................................... 1-7 Taking a Look at the Computer ............................................. 1-8 Front Components .............................................................. 1-8 Rear Components ............................................................. 1-10 Right-Side Components .................................................... 1-11 Left-Side Components ...................................................... 1-11 Top-open Components ..................................................... 1-13 Bottom Components ........................................................ 1-15 Using the Accessories ............................................................ 1-16 Using the Tether (Optional) ............................................. 1-16 Attaching the Handgrip Strap ......................................... 1-17 Attaching the Shoulder Strap .......................................... 1-18 Chapter 2 Operating Your Computer ............................................ 2-1 Starting and Stopping the Computer .................................... 2-2 Starting the Computer ....................................................... 2-2 Stopping the Computer ..................................................... 2-2 Using the Internal Keyboard .................................................. 2-4 Typewriter Keys .................................................................. 2-4 Cursor-Control Keys ............................................................ 2-4 Numeric Keypad ................................................................. 2-5

Fn Key .................................................................................. 2-6 Hot Keys .............................................................................. 2-6 Using the Touchpad ................................................................ 2-8 Configuring the Touchpad ............................................... 2-10 Navigating on the Screen ..................................................... 2-11 Using the Touchscreen ..................................................... 2-11 Using Multi-touch Gestures (Windows 7 Only) .............. 2-12 Using the Dual Mode Display (Optional) ........................ 2-15 Using the Input Panel ........................................................... 2-18 Using OSD Control Panel ...................................................... 2-19 Using the Fingerprint Scanner (Optional) ........................... 2-20 Using the Video Features ..................................................... 2-22 Configuring the Display Modes ....................................... 2-22 Using Landscape or Portrait View ................................... 2-23 Using the Audio Features ..................................................... 2-25 Connecting Audio Devices ............................................... 2-25 Using G-Camera Lite ............................................................. 2-27 Using the Network Features .................................................. 2-28 Using the Modem ............................................................. 2-28 Using the LAN ................................................................... 2-29 Using the Wireless LAN .................................................... 2-29 Using the Bluetooth Feature ................................................ 2-32 Turning On/Off the Bluetooth Radio .............................. 2-32 Connecting to another Bluetooth Device ....................... 2-33 Chapter 3 Managing Power ........................................................... 3-1 AC Adapter .............................................................................. 3-2 Battery Pack ............................................................................. 3-3 Charging the Battery Pack ................................................. 3-3 Checking the Battery Level ................................................ 3-4 Replacing the Battery Pack ................................................ 3-5 Battery Low Signals and Actions ....................................... 3-6 Power Management ............................................................... 3-7

Power-Saving Tips ................................................................... 3-9 Chapter 4 Expanding Your Computer ........................................... 4-1 Connecting an External Monitor ........................................... 4-2 Connecting a Serial Device ..................................................... 4-3 Connecting a USB Device ....................................................... 4-4 Connecting an eSATA Device ................................................. 4-5 Using Smart Cards (Optional) ................................................. 4-6 Using PC Cards ......................................................................... 4-7 Using ExpressCards (Optional) ............................................... 4-9 Using the SD Card Reader .................................................... 4-11 Using the Port Replicator (Optional) ................................... 4-12 System Memory Upgrade ..................................................... 4-13 Chapter 5 Using BIOS Setup and System Recovery ...................... 5-1 BIOS Setup ............................................................................... 5-2 When and How to Use ....................................................... 5-2 Main Menu .......................................................................... 5-3 Advanced Menu .................................................................. 5-4 Security Menu ..................................................................... 5-6 Boot Menu .......................................................................... 5-8 Exit Menu ............................................................................ 5-9 System Recovery .................................................................... 5-10 Chapter 6 Installing Software Drivers and Utilities .................... 6-1 How to Use the Driver Disc .................................................... 6-2 Installation for Windows XP .................................................. 6-3 Drivers on the First Page .................................................... 6-3 Drivers on the Second Page ............................................... 6-4 Installation for Windows Vista ............................................... 6-6 Drivers on the First Page .................................................... 6-6 Drivers on the Second Page ............................................... 6-7 Drivers on the Third Page .................................................. 6-8 Installation for Windows 7 ................................................... 6-10

Drivers on the Second Page ............................................. 6-11 Drivers on the Third Page ................................................ 6-12 Chapter 7 Using Getac Software ................................................... 7-1 Using G-Manager .................................................................... 7-2 Using Button Manager ........................................................... 7-4 Chapter 8 Caring for the Computer .............................................. 8-1 Protecting the Computer ....................................................... 8-2 Using an Anti-Virus Strategy ............................................. 8-2 Using Security Center (for Windows Vista) or Action Center (for Windows 7) ...................................................... 8-2 Using the Cable Lock .......................................................... 8-3 Taking Care of the Computer ................................................ 8-4 Location Guidelines ............................................................ 8-4 General Guidelines ............................................................. 8-4 Cleaning Guidelines ............................................................ 8-5 Battery Pack Guidelines ...................................................... 8-5 Touchscreen Guidelines ...................................................... 8-6 When Traveling ....................................................................... 8-8 Chapter 9 Troubleshooting ............................................................ 9-1 Preliminary Checklist ............................................................... 9-2 Solving Common Problems .................................................... 9-3 Battery Problems ................................................................ 9-3 Bluetooth Problems ............................................................ 9-3 Display Problems ................................................................. 9-4 Hardware Device Problems ................................................ 9-5 Hard Disk Drive Problems ................................................... 9-5 Keyboard, Mouse, and Touchpad Problems ..................... 9-6 LAN Problems ...................................................................... 9-6 Modem Problems ................................................................ 9-7 PC Card Problems ................................................................ 9-7 Power Management Problems .......................................... 9-7 Software Problems ............................................................. 9-8

Startup Problems ................................................................ 9-9 WLAN Problems ................................................................ 9-10 Other Problems ................................................................. 9-11 Resetting the Computer ....................................................... 9-12 Appendix A Specifications ............................................................... A-1 Appendix B Regulatory Information .............................................. B-1 On the Use of the System ....................................................... B-2 Class B Regulations ............................................................. B-2 UL1604 Installation Instructions ........................................ B-3 Safety Notices ..................................................................... B-4 On the Use of the RF Device .................................................. B-7 USA and Canada Safety Requirements and Notices ........ B-7 European Union CE Marking and Compliance Notices .. B-10

Chapter 1 Getting Started Congratulations on purchasing this rugged computer. This chapter first tells you step by step how to get the computer up and running. Then, you will find a section briefly introducing the external components of the computer.

Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: z Notebook computer z Accessories: − AC adapter − AC power cord − Shoulder strap − Handgrip strap − Driver disc − Document(s) − Stylus (option) − Digitizer pen and size “AAAA” battery (option) − Tether (option) Inspect all the items. If any item is damaged or missing, notify your dealer immediately. Keep the shipping carton and packing materials in case you need to ship or store the computer in the future.

Connecting to AC Power The computer operates either on the external AC power or internal battery power. It is suggested that you use AC power when you start up the computer for the very first time. CAUTION: Use only the AC adapter included with your computer. Using other AC adapters may damage the computer. 1. Make sure that the computer is turned off. 2. Plug the DC cord of the AC adapter to the power connector of the computer (n). 3. Plug the female end of the AC power cord to the AC adapter and the male end to an electrical outlet (o). 4. When the AC adapter is connected, power is being supplied from the electrical outlet to the AC adapter and onto your computer. Now, you are ready to turn on the computer.

CAUTION: z When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. z When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening and Closing the Cover To open the top cover: 1. Pull loose the cover latch (n) and release the clamp (o). 2. Lift up the cover (p). You can tilt the cover forward or backward for optimal viewing clarity.

To close the top cover: 1. Close the display. 2. Lift the cover latch and engage the clamp on the display. Then, push in the cover latch to click it into place. Operating in Tablet Mode In addition to being used as a regular notebook computer (Laptop mode), your computer can also be operated in Tablet mode. In Tablet mode, you operate the computer with a stylus or digitizer pen, or a fingertip, instead of a keyboard or mouse. 1. Open the top cover so that it is almost perpendicular with the keyboard of the computer. 2. Turn the display counter-clockwise by 165o. CAUTION: Do not rotate the display more than 165 o, or attempt to rotate the display clockwise.

3. Close the computer with the display facing up. 4. Lift the cover latch and engage the clamp on the display. Then, push in the cover latch to click it into place. In Tablet mode, the computer can be operated while holding it as shown. A handgrip strap is supplied to help you hold the computer. (See “Attaching the Handgrip Strap” in this chapter for installation instructions.)

To return to Laptop mode, perform the steps for changing the computer into Tablet mode in reverse order. Turning On and Off the Computer Turning On 1. Make sure that the computer is connected to AC power. 2. Press the power button ( ). 3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.) CAUTION: If you have to turn the computer on again immediately after turning it off, wait for at least five seconds. Turning the computer off and on rapidly can damage it.

Taking a Look at the Computer NOTE: z Depending on the model you purchased, the appearance of your computer may not be exactly the same as those shown in this manual. z You need to open the protective covers to access the connectors. When not using a connector, make sure to close the cover completely for water- and dust-proof integrity. (Engage the locking mechanism if existing.) Front Components Ref Component Description n Strap Holder Two buckles hold the shoulder strap. Four bottom hooks hold the handgrip strap. o Speaker Sends out sound and voice from your computer. p OSD Control Button Opens or closes the OSD (On Screen Display) control panel. P1 Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.) q Sunlight- readable Button Toggles the sunlight-readable mode ON and OFF. IMPORTANT: To prevent burns to your fingers if using the computer (especially in Tablet Mode) with sunlight-readable mode turned on, do wear gloves when touching the top portion of the LCD display as it may be hot to the touch.

Ref Component Description P2 Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.) r RF Button Toggles the wireless LAN /Bluetooth/3G radio frequency ON and OFF. P3 Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.) s Reset Button Serves as the Ctrl+Alt+Del keyboard keys. P4 Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.) t Software Keyboard Button Opens or closes the software keyboard on your screen. P5 Can be re-defined using the OSD utility. (See “Using Button Manager” in Chapter 7 for information.) u Top Cover Latch Locks the top cover. v Power Button Turns the computer power ON and OFF.

Rear Components Ref Component Description n Strap Holder Two buckles (option) hold the shoulder strap. Four bottom hooks hold the handgrip strap. o Audio Output Connector Connects a set of headphones, external speakers with amplifier, or an audio recording device. p Microphone Connector Connects an external microphone. q USB Port Connects a USB device, such as a flash disk, printer, digital camera, joystick, and more. r Kensington Lock Locks the computer to a stationary object for security. s VGA Connector Connects an external display monitor. NOTE: Depending on your model, this port could be a serial connector. t Serial Connector Connects a serial mouse or serial communication device.

Right-Side Components Ref Component Description n Battery Pack Compartment Inside is the battery pack that supplies power to your computer when external power is not connected. o Hard Disk Drive Compartment Inside is the hard disk drive. Left-Side Components

Ref Component Description n Power Connector Connects the AC adapter. o USB Port Connects a USB device, such as a flash disk, printer, digital camera, joystick, and more. p eSATA/USB Combo Port Connects an eSATA device such as an external hard drive or optical drive. Can also function as a USB port. q RJ-11 Connector Connects the telephone line. r RJ-45 Connector Connects the LAN cable. s Can be one of the below depending on your model: ExpressCard Slot Accepts an ExpressCard for additional functions. PCMCIA Slot Accepts a PC card for additional functions. t Can be one of the below depending on your model: Smart Card Reader Accepts a smart card for additional security feature. PCMCIA Slot Accepts a PC card for additional functions. u SD Card Reader Accepts a SD (Secure Digital) card for removable storage media.

Top-open Components Ref Component Description n Webcam Lens (option) Allows you to use your computer’s camera function. The camera lens can be rotated. o LCD Screen Displays the output of the computer. May include the optional touchscreen feature. p Light Sensor Detects the surrounding lighting condition for automatic adjustment of the LCD brightness and optional keyboard backlight. q Fingerprint Scanner (option) Uses fingerprint verification to protect your computer against unauthorized access. r Keyboard Serves as the data input device.

Ref Component Description s Indicators Show the current status of the computer’s devices. Power Lights green when the computer is turned on. Lights yellow when the computer is in Sleep mode. Battery Charge Lights green when the battery is fully charged. Lights yellow when the battery is being charged. Blinks yellow when the battery’s capacity is below 10%. Blinks green and yellow by turns to indicate charging is suspended because the battery’s temperature is either too high or too low. Hard Disk Drive In-Use Lights green when the computer is accessing the hard disk drive. Blinks red when the optional hard disk drive heater is on for low temperature operation. RF Lights when the wireless LAN/Bluetooth/3G radio frequency is on. Num Lock Lights when Num Lock is on. Caps Lock Lights when Caps Lock is on. t Stylus/Digitizer Pen (option) Serves as the input device by tapping on the screen to make selections and enter information. u Touchpad Serves as the pointing device.

Bottom Components Ref Component Description n Expansion Bus Connector Inside is the expansion bus connector for using the Port Replicator option. o Memory Slots Inside are the memory slots for expanding the memory size of your computer.

Using the Accessories Using the Tether (Optional) A tether is provided for attaching the stylus to your computer. 1. Insert one of the tether’s loop ends through the hole of the stylus (as indicated by n below). Then, insert the other end through the first loop (as indicated by o below) and pull it tight. 2. Insert the other loop end to the tether hole on the computer (as indicated by n below). Then, insert the stylus end through the loop (as indicated by o below) and pull it tight.

Attaching the Handgrip Strap To use the handgrip strap, attach its four loops to the four bottom hooks on your computer. Make sure the loops are securely hooked. When you need to operate and hold your computer at the same time, insert your hand through the strap for a firm grip.

Attaching the Shoulder Strap To use the shoulder strap, secure the snap hooks to the two buckles on your computer. (Select models have four buckles for different positioning of the strap.) CAUTION: z The strap has been designed to carry only the weight of the computer. Therefore, be sure that the strap does not carry a weight that exceeds the weight of the computer. The strap may accidentally come loose from the computer. z Do not use a strap that is damaged or about to tear.

Chapter 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user, you may choose to read only the parts containing information unique to your computer. CAUTION: The computer can get uncomfortably warm when you use it in high temperatures. As a safety precaution in such a circumstance, do not place the computer on your lap or touch it with your bare hands for extended periods of time. Prolonged body contact can cause discomfort and potentially a burn.

Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk. The computer will automatically load the OS after you turn it on. This process is called booting. NOTE: An operating system is the platform for all your software application programs to run on. Your computer uses the Microsoft Windows operating system. Stopping the Computer When you finish a working session, you can stop the computer by turning off the power or leaving the computer in Standby/Sleep or Hibernation mode: To stop in this mode... Do this... To start up or resume again Off Follow the shutdown procedure of your operating system. This can prevent loss of unsaved data or damage to your software programs. If the system is locked up because of hardware or software problems, press the power button to turn off the computer. Press the power button.

To stop in this mode... Do this... To start up or resume again Standby/Sleep Depending on your settings in Windows, you can place the computer in Standby/Sleep mode by: • Closing the display cover • Pressing the Fn+F12 hot key • Pressing the power button Press any key. Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover • Pressing the Fn+F12 hot key • Pressing the power button Press the power button. If you choose to stop in Standby/Sleep or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.)

Using the Internal Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus an Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: z Typewriter keys z Cursor-control keys z Numeric keys z Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes. When the lock keys (Caps Lock and Num Lk) are pressed, their corresponding indicators light up. The Control (Ctrl) / Alternate (Alt) key is normally used in combination with other keys for program-specific functions. The Escape (Esc) key is usually used for stopping a process. Examples are exiting a program and canceling a command. The function depends on the program you are using. Cursor-Control Keys Cursor-control keys are generally used for moving and editing purposes. NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes.

Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTE: z When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off. z Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead.

Function Keys On the top row of the keys are the function keys: F1 to F12. Function keys are multi-purpose keys that perform functions defined by individual programs. Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key. Hot Keys Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way. Each time a hot key combination is pressed, it shifts the corresponding function to the other or next choice. You can easily identify the hot keys with the icons imprinted on the keytop. The hot keys are described next. Key Description Switches the keyboard backlight on and off (optional). Switches the wireless radio on and off. Decreases the sound volume. Increases the sound volume.

Key Description Switches the display output when external devices are connected. NOTE: This function only applies to Plug & Play display devices. Decreases the LCD brightness (20 levels). Increases the LCD brightness (20 levels). Switches the touchscreen on and off (option). Switches the touchpad on and off. Switches the system sound output off (mute) and on. Switches LCD backlight on and off. Serves as the sleep button that you can define with Windows’ Power Options. (See the “Power Management” in Chapter 3.) Windows Keys The keyboard has two keys that perform Windows-specific functions: Windows Logo key and Application key. The Windows Logo key opens the Start menu and performs software-specific functions when used in combination with other keys. The Application key usually has the same effect as a right mouse click. (See your Windows manual for more information.)

Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons. The touchpad consists of a rectangular pad (work surface) and a left and right buttons. To use the touchpad, place your forefinger or thumb on the pad. The rectangular pad acts like a miniature duplicate of your display. As you slide your fingertip across the pad, the pointer (also called cursor) on the screen moves accordingly. When your finger reaches the edge of the pad, simply relocate yourself by lifting the finger and placing it on the other side of the pad. Here are some common terms that you should know when using the touchpad:

Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Double-click Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination. The object will drop into the new location. –or– Gently tap twice on the pad and on the second tap, keep your finger in contact with the pad. Then, move your finger across the pad to drag the selected object to your destination. When you lift your finger from the pad, the selected object will drop into place. Scroll To scroll is to move up and down or left and right in the working area on the screen. To move vertically, place your finger on the right or left edge of the pad and slide your finger up and down along the edge. To move horizontally, place your finger on the top or bottom edge of the pad and slide your finger left and right. This function works only after you install the touchpad driver supplied with the computer and it may not work for all applications. TABLE NOTE: If you swap the left and right buttons, “tapping” on the touchpad as an alternative method of pressing the left button will no longer be valid.

Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vice versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, go to Control Panel Æ Mouse Properties.

Navigating on the Screen The screen of your computer is touch-sensitive. You can control the location of the cursor/pointer on the screen using your finger or the included stylus or digitizer pen to communicate with the computer. CAUTION: Do not use sharp objects on the LCD display. Doing so may damage the display surface. Use your finger or the included stylus or digitizer pen. NOTE: When there is a noticeable discrepancy in the placement of the stylus on the screen and the indicated position of the onscreen pointer, calibrate the touchscreen using the calibration utility called IdeaCom Calibration on Windows XP/Vista or CalTouch on Windows 7. Using the Touchscreen If your computer is equipped with the touchscreen feature, you can use your finger or the included stylus to navigate and select objects on the screen.

Here are some common terms that you should know when using the touchscreen: Term Action Click/Point Tap gently on the touchscreen. Double-click Tap twice on the touchscreen rapidly. Drag and drop Tap lightly on the touchscreen and move your finger until you reach your destination (drag). Finally, release your finger (drop) when you finish dragging your selection to the destination. The object will drop into the new location. Using Multi-touch Gestures (Windows 7 Only) If your computer model comes with multi-touch-capable screen and Windows 7, you can interact with your computer by placing two fingers on the screen. The movement of the fingers across the screen creates “gestures,” which send commands to the computer. Here are the multi-touch gestures that you can use: Gestures Actions ( = finger down; = finger up) Descriptions Pan (Scroll) or Drag 1 or 2 fingers up or down. Use panning to see another part of a page that has scroll bars.

Gestures Actions ( = finger down; = finger up) Descriptions Zoom (Pinch) Move two fingers apart/toward each other. Use zooming to make an item (a photo for example) on the screen larger or smaller. The gesture works in applications that support mouse wheel zooming. Rotate or Move two fingers in opposing directions. -or- Use one finger to pivot around another. Use rotating to move a picture or other item on the screen in a circular direction (clockwise or counter- clockwise). The gesture works in applications that support the specific gesture. Press and Tap Press on target and tap using a second finger. Use press and tap to access the shortcut menu.

Gestures Actions ( = finger down; = finger up) Descriptions Two- finger Tap Tap two fingers at the same time (where the target is in the midpoint between the fingers). The function is defined by applications that support the specific gesture. Flicks Make quick drag gestures in the desired direction. Flick left or right to navigate back and forward in a browser and other applications. The gesture works in most applications that support back and forward.

Using the Dual Mode Display (Optional) Dual mode display incorporates both touchscreen and digitizer functions. The display is set to Touchscreen mode by default. Touchscreen mode provides all the functionalities that an ordinary touchscreen has. When the computer receives signals from the active digitizer pen, the display automatically switches to Digitizer mode. When using the digitizer pen, be sure to install the included size “AAAA” battery. Here are some common terms that you should know when using the active digitizer feature: Term Action Wake up The digitizer pen automatically enters Sleep mode after 30 seconds of inactivity. To start using the pen, tap the tip of the pen to activate it.

Term Action Move Move the cursor pointed by the digitizer pen. Click/Point Tap gently on the display. Double-click Tap twice on the display rapidly. Drag and drop Tap lightly on the display and move your digitizer pen until you reach your destination (drag). Finally, release your digitizer pen (drop) when you finish dragging your selection to the destination. The object will drop into the new location. Right-click Press and hold down the digitizer pen button (A), then tap gently the object. CAUTION: z When the LCD display is used alone or with an external display simultaneously, the digitizer function cannot be used when the area of either display is set larger than the default setting of the display resolution. z Even when only an external display is in use, the cursor will move on the external display if you touch the surface of the LCD display with the pen or bring the pen close to the surface of the LCD display when the digitizer driver is active. Therefore, do not touch the LCD display when only an external display is in use.

z The active digitizer feature cannot be used in the BIOS Setup program or when using the full screen in DOS mode. NOTE: z You can move the cursor by bringing the digitizer pen close to the screen, without actually touching the screen’s surface. z Do not move the digitizer pen too quickly. If the pen moves too quickly, the cursor may be unable to follow its movement. z If you cannot click on the edge of the screen, hold the digitizer pen perpendicular to the display and try clicking again.

Using the Input Panel Use the Input Panel to enter text and perform various keyboard functions. There are two types of Input Panels for you to use in Windows 7: z Touch Keyboard allows you to enter text by tapping the keys with your stylus, like pressing the keys on a standard keyboard. z Writing Pad allows you to write on the writing pad, like writing on a piece of paper. Your handwriting will be converted into typed text. To open the Input Panel, tap the Input Panel tab, which appears by default on the left edge of the screen. (You can also press the button on the front of the computer to open or close the Input Panel.) To switch between the two types, tap or at the upper left corner of the Input Panel. NOTE: For more information on using the Input Panel, see Windows’ online help.

Using OSD Control Panel The OSD Control Panel allows you to easily activate or operate certain functions on your computer. To use the OSD Control Panel: 1. Press the button on the front of your computer. 2. The following screen appears, providing several control buttons. For detailed descriptions of the Control Panel, click the button. 3. To close the Control Panel, either press the button on your computer again or click the button .

Using the Fingerprint Scanner (Optional) The fingerprint scanner provides a strong authentication mechanism based on fingerprint recognition. You can log on to your computer or sign in to a web site with your fingerprint instead of a password. You can also encrypt files and folders with your fingerprint. NOTE: You can register a fingerprint only after creating a password for the Windows user account. CAUTION: For the fingerprint file/folder encryption feature, the maximum file/folder size allowed is 2GB. To register your fingerprint, click Start Æ All Programs Æ Fingerprint Software Æ Fingerprint Registration. Click the finger you want to register and follow the onscreen instructions to complete.

You can then use the Fingerprint Software to set up how the fingerprint authentication works. For detailed information, click Start Æ All Programs Æ Fingerprint Software Æ Help.

Using the Video Features The video subsystem of your computer features: z 12.1-inch wide TFT (Thin-Film Transistor) color LCD display with 1200×800 WXGA resolution z Simultaneous display on LCD and external monitor z Multi-display capability z Built-in light sensor to automatically adjust the LCD brightness and optional keyboard backlight z Power Management z Sunlight-readable LCD display NOTE: The computer enters the Standby/Sleep or Hibernation mode when the LCD is closed. If you want to use the computer with the LCD closed, set according in Windows Control Panel so the computer does not enter the Standby/Sleep or Hibernation mode when the LCD is closed. Configuring the Display Modes NOTE: When using an external CRT monitor, the resolution depends on the CRT monitor’s supported resolution. Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.)

Using Landscape or Portrait View After Windows is started up, you can rotate the display and perform the touchscreen and active digitizer operations in the rotated mode. To rotate the display, press the button located on the front of your computer to open the OSD control panel and click . Each time this Rotate button is clicked, the screen display rotates counter-clockwise by 90O. NOTE: z If the screen display resolution has been set to 800×600 pixels, you can rotate the display to Primary Landscape and Secondary Landscape only. z While the display is rotated: – Do not set the display resolution larger than the resolution of the LCD display. – If you exit Windows, the next time Windows is started up, the operation of the touchpad will not match the display angle for a few seconds. – The computer’s performance will decrease slightly. – If a video is played, the picture may not be displayed properly or the sound may be broken up. This problem can be corrected by rotating the display to Primary Landscape. – The touchpad’s scroll function does not work. z The display cannot be rotated when DOS mode is set to “Full Screen.” For a Model without 3G Module Primary Landscape Primary Portrait Secondary Landscape Secondary Portrait Primary Landscape Display Display Display Display Display

For a Model with 3G Module Primary Landscape Primary Portrait Secondary Landscape Primary Landscape NOTE: Due to SAR of FCC, a minimum distance of 20 cm must be maintained between the human body and the 3G antenna located on both sides of the LCD display. Display Display Display Display

Using the Audio Features NOTE: If you experience interference while recording, try lowering the microphone recording volume. The audio subsystem of your computer features: z Built-in sound system for recording and playing sound on your computer z Azalia interface (high density audio codec) z Built-in Speaker z External audio connectors Ways of playing and recording sound vary with the operating system used. See your operating system documentation or online help for specific information. Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. NOTE: After connecting an external audio device, make sure that you specify the use of the correct audio device in Windows.

z Audio Output Connector ( ) can be connected to speakers, headphones, or earphone set. z Microphone Connector ( ) can be connected to an external microphone for recording voice or sound. NOTE: When using the external speakers/headphones or microphone, you cannot use the internal one.

Using G-Camera Lite G-Camera Lite allows you to take pictures with the Webcam, if supplied with your computer. To start G-Camera Lite, click Start Æ All Programs Æ G-Camera Lite Æ G-Camera Lite. The camera control panel appears. Click the Shutter button or press Enter to take photos. For detailed descriptions of G-Camera Lite, click the button . Mode Current settings Setting buttons for different modes

Using the Network Features Using the Modem The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line. NOTE: z When using the communication software, you may have to disable power management. z Set parameters such as modem speed (baud rate) and line type (pulse dialing or tone dialing). z Do not enter the Standby/Sleep mode when using the communication software.

Using the LAN The internal 10/100/1000Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub. Using the Wireless LAN Depending on your model, an internal mini PCI-E wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: z Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes support z WEP (Wired Equivalent Privacy) 64/128-bit data encryption z IEEE 802.11a/g/n standard compliance

Technology 802.11a 802.11g 802.11n Stated Maximum Throughput (Mbps) 54 54 100 Mbps or more Data Rates (Mbps) 54, 48, 36, 24, 18, 12, 9, 6 54, 36, 18, 9 100 ~ 210 Band (GHz) 5.15 ~ 5.35 2.4 2.4 / 5 Modulation Technology OFDM (Orthogonal Frequency Division Multiplexing) OFDM (Orthogonal Frequency Division Multiplexing) Spatial multiplexing, uses MIMO (multiple- input multiple- output) To take advantage of the WLAN feature, make sure that the WLAN driver is installed correctly. If your WLAN card was provided by your dealer instead of the computer manufacturer, contact your dealer for the correct driver to use. Turning On/Off the WLAN Radio NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to turn off wireless LAN when using your computer in the airplane. 1. Press Fn+F1 to turn on or off the wireless radio. The indicator lights up to indicate the wireless radio is on. 2. Windows Mobility Center has wireless network turned on by default. The Wireless Network icon on the taskbar should appear without a red X. (In case you have previously turned it off in Windows Mobility Center, be sure to turn it on when using the function the next time.)

Connecting to a Wireless Network To connect to a wireless network: 1. Make sure that the WLAN radio is on (as described in the previous section). 2. Tap the Wireless Network icon on the taskbar. (An orange light in the icon indicates connections are available.) 3. In the list of available wireless networks, tap a network, and then tap Connect. 4. Some networks require a network security key or passphrase. To connect to one of those networks, ask your network administrator or Internet service provider (ISP) for the security key or passphrase. For more information on setting a wireless network connection, refer to Windows online help. NOTE: You can use Intel® PROSet Wireless to take full advantage of the WiFi capabilities of your computer. See the Help of the utility for instructions.

Using the Bluetooth Feature Your computer incorporates the Bluetooth capability for short-range (about 10 meters) wireless communications between devices without requiring a cable connection. With Bluetooth, data can be transmitted through walls, pockets and briefcases as long as two devices are within range. Turning On/Off the Bluetooth Radio 1. Press Fn+F1 to turn on or off the wireless radio. The indicator lights up to indicate the wireless radio is on. 2. The Bluetooth function is enabled by default, as indicated by the Bluetooth icon on the Windows taskbar. (In case you have previously disabled the function in the Bluetooth utility, be sure to enable it when using the function the next time.). The status of the Bluetooth connection is indicated by the Bluetooth icon located in the taskbar. (You need to tap on the taskbar to show the hidden icons.) Status Icon Off (blue with red logo) On (blue with white logo). Connected (blue with green logo) You can use the Bluetooth Utility to configure Bluetooth wireless connection settings and transfer files.

Connecting to another Bluetooth Device 1. Make sure that the Bluetooth function is enabled (as described above). 2. Make sure that the target Bluetooth device is turned on, discoverable and within close range. (See the documentation that came with the Bluetooth device.) 3. Start the Bluetooth utility by double-clicking the Bluetooth icon on the taskbar and click New Connection. 4. The Add New Connection Wizard window appears. Select Express Mode (Recommended), and then click Next.

5. Select the device to connect to and click Next. 6. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information. For detailed information on using the Bluetooth Utility, see the Bluetooth Utility Help.

Chapter 3 Managing Power Your computer operates either on external AC power or on internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.

AC Adapter CAUTION: z The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. z The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. z When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or computer. z When unplugging the connector, always hold the plug head. Never pull on the cord. The AC adapter serves as a converter from AC (Alternating Current) to DC (Direct Current) power because your computer runs on DC power, but an electrical outlet usually provides AC power. It also charges the battery pack when connected to AC power. The adapter operates on any voltage in the range of 100~240 V AC.

Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 8. Charging the Battery Pack NOTE: z Charging will not start if the battery’s temperature is below 0 °C (32 °F) or above 40 °C (104 °F); the charging process will stop if the battery’s temperature gets above 60 °C (140 °F). To avoid damaging the battery under this situation, disconnect the AC adapter and wait for the battery to return to room temperature before charging again. z During charging, do not disconnect the AC adapter before the battery has been fully charged; otherwise you will get a prematurely charged battery. To charge the battery pack, connect the AC adapter to the computer and an electrical outlet. The Battery Charge Indicator ( ) on the computer glows yellow to indicate that charging is in progress. You are advised to keep the computer power off while the battery is being charged. When the battery is fully charged, the Battery Charge Indicator is off. It takes approximately 3 hours to fully charge the Li-Ion battery pack when the computer is off, and approximately 6 hours to fully charge the Li-Ion battery pack when the computer is on.

CAUTION: After the computer has been fully recharged, do not immediately disconnect and reconnect the AC adapter to charge it again. Doing so may damage the battery. NOTE: The battery level may automatically lessen due to the self-discharge process (0.21 % per day), even when the battery pack is fully charged (100 %). This happens no matter if the battery pack is installed in the computer. Checking the Battery Level NOTE: Any battery level indication is an estimated result. The actual operating time can be different from the estimated time, depending on how you are using the computer. By Operating System You can check the approximate battery level using the battery meter function of the operating system. To read the battery level in Windows, click the battery icon on the taskbar. By Gas Gauge On the exterior side of the battery pack is a gas gauge for displaying the estimated battery charge. When the battery pack is not installed in the computer and you want to know the battery charge, you can press the switch with a pointed device to see the corresponding value of indicator segment that light green. Switch

The value of the corresponding green segment indicates the relative percentage of the battery charge. The battery pack is fully discharged when you see no segment glowing green. Replacing the Battery Pack CAUTION: z There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. z Do not attempt to disassemble the battery pack. If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup. To replace the battery pack, follow these steps: 1. Make sure that the computer is not turned on or connected to AC power. 2. Locate the battery compartment on the right side of the computer. 3. Slide the door lock toward the left to unlock (n). Then slide the door latch downward to open the door( o). 4. Pull on the ribbon strip to remove the battery pack.

5. With the ribbon strip facing outward, slide the new battery pack all the way into the slot. 6. Close the door. Make sure the door latch clicks into place. Then, slide the door lock toward the right. Battery Low Signals and Actions When the battery is low, Windows gives warning messages and the Battery Charge Indicator ( ) blinks yellow to alert you. Immediately save your data upon Battery Low. The remaining operating time depends on how you are using the computer. If you are using the audio subsystem, PC card, hard or USB flash disk, the battery might run out of charge very quickly. Always respond to Battery Low by connecting the AC adapter, turning off the computer, or placing your computer in Hibernation mode. If you do not take any action, the computer will automatically hibernate and turn off. NOTE: You can set up the threshold of Battery Low and actions for Windows to take with Windows Power Options. (For more information, see Windows’ Help.)

Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time. In general, Windows’ power management works in this way: What... When... Power to the hard disk is turned off When the hard disk has been idle for a set period. Power to the display is turned off When the display has been idle for a set period. The computer enters the Standby/Sleep mode. The hard disk and display are turned off and the entire system consumes less power. When the entire system has been idle for a set period. When you manually activate the mode. The computer enters the Hibernation mode. (See the next subsection for more information.) When the entire system has been idle for a set period. When you manually activate the mode. For detailed information on power management, see Windows’ Help.

Hibernation Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the computer can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shuts down. The next time you turn on your computer, you return to exactly where you left off.

Power-Saving Tips Aside from enabling your computer’s power saving mode (see previous section), you can do your part to maximize the battery’s operating time by following these suggestions. z Do not disable Power Management. z Decrease the LCD brightness to the lowest comfortable level. z Shorten the length of time before Windows turn off the display. z Many USB devices use power just by being connected. If you use a USB mouse, you can save power by disconnecting the mouse and using the touchpad. If you use a USB flash drive, unplug it when you are not using it. z If you work with an application that uses a PC card, exit the application when you finish using it. z If you have a PC card installed, remove it when not in use. Some PC cards drain power even while they are inactive. z Turn off the wireless radio if you are not using the wireless module. z Turn off the computer when you are not using it.

Chapter 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.

Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external display monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s D-type signal connector to the computer’s VGA connector. 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4. To use the monitor, turn on the monitor before turning on the computer. 5. The monitor should respond by default. If not, you can switch the display to the monitor or to both (simultaneous display), or to multi-display by pressing the Fn+F5 hot key. In Windows, you can also change the display through the settings in Display Properties. 6. You can change display settings through your operating system. See your operating system documentation or online help for specific information. CAUTION: Do not disconnect the external monitor while the computer is in the Standby/Sleep mode or Hibernation mode. If no external monitor is connected when the computer resumes, the LCD might not display properly.

Connecting a Serial Device Your computer has one or two serial port (depending on model) for connecting a serial device such as a serial mouse or serial communication device (modem). Follow this procedure to connect a serial device: 1. Make sure the computer is not turned on 2. Plug the device cable to the serial port on the rear of the computer. 3. Turn on the computer. NOTE: Portable modems that derive power through the serial port cannot be used with the computer. Instead, use a modem that is powered by its own internal battery or external AC power.

Connecting a USB Device Your computer has two USB ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. NOTE: The eSATA/USB Combo port can also function as a USB port. The USB port support transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices. To connect a USB device, simply plug the device cable to one of the USB ports.

Connecting an eSATA Device Your computer has an eSATA/USB Combo port for connecting eSATA devices (such as an external hard drive and external optical drive) / USB devices (see previous section). The port supports SATA II with transfer rate up to 3.0Gbit/s. It can provide 5V power if a certified USB-eSata combo cable is used. To connect an external eSATA device, simply plug the device cable to the eSATA port.

Using Smart Cards (Optional) Your computer may have a smart card reader. With an embedded microcontroller, smart cards have the unique ability to store large amounts of data, carry out their own on-card functions (e.g., encryption and mutual authentication), and interact intelligently with a smart card reader. To insert a smart card: 1. Locate the smart card slot (the one without the eject button). 2. Slide the smart card, with its label and embedded computer chip facing up into the slot. 3. When a new card is seated, use the third-party smart card software to allow your computer to read it. To remove a smart card: 1. Make sure that the third-party smart card software is not accessing the smart card. 2. Pull the card out of the slot.

Using PC Cards NOTE: z Some PC cards require additional system resources. Before using such PC card, you may have to free other system resources for the PC card. z Although some PC cards can be inserted and removed without turning off the computer, you cannot remove or install PC cards during Sleep/Standby mode. Your computer has one or two PC card slots that support CardBus specifications. The slots can accommodate a type II card. Typical type II cards are flash memory, SRAM, modem, LAN, and SCSI cards. To insert a PC card: 1. Locate the PC card slot on the left side of the computer. 2. Slide the PC card, with its label facing up, into the slot until the eject button pops out. 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove a PC card: 1. Double-click on the Safely Remove Hardware icon ( for Windows Vista/Windows 7 or for Windows XP) found on the Windows taskbar and the Safely Remove Hardware window appears on screen. Eject button

2. Select (highlight) the PC card from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot.

Using ExpressCards (Optional) NOTE: The ExpressCard interface is not compatible with the PC card interface. Your computer may have an ExpressCard slot. ExpressCard supports the PCI Express and USB 2.0 serial data interfaces (supporting speeds of up to 2.5 Gbps and 480 Mbps respectively), improving speed in data transfer while conserving power usage. The ExpressCard slot can accommodate a 54 mm (ExpressCard/54) or 34 mm (ExpressCard/34) wide ExpressCard. Typical ExpressCards support a very extensive range of applications including memory, wired and wireless communication cards, and security devices. Shown next are the appearances of ExpressCards for your reference. ExpressCard/54 ExpressCard/34

To insert an ExpressCard: 1. Locate the ExpressCard slot on the left side of the computer (the upper one). 2. Slide the ExpressCard, with its label facing up, all the way into the slot until the rear connectors click into place. 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove an ExpressCard: 1. Double-click on the Safely Remove Hardware icon ( for Windows Vista/Windows 7 or for Windows XP) found on the Windows taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the ExpressCard from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot. Eject button

Using the SD Card Reader NOTE: z If your hard disk is divided into several drives, make sure that all drives have been formatted before using the Card Reader. Otherwise, you may encounter problems when using the Card Reader. z You can use only storage cards. Your Card Reader does not support cards with I/O (input/output) functions such as a wireless network card or Bluetooth card. Your computer has a Card Reader. The Card Reader is a small drive for reading from and writing to removable storage cards (or called memory cards). The Card Reader supports Secure Digital (SD) cards. To insert a storage card: 1. Locate the Card Reader slot on the left side of the computer. 2. Align the card with its connector pointing to the slot and its label facing up. Slide the card into the slot until it reaches the end. 3. Windows will detect the card and assign it a drive name. To remove a storage card: 1. Double-click My Computer. 2. Right-click the drive with the card and select Eject. 3. Push the card to release and then pull the card out of the slot.

Using the Port Replicator (Optional) NOTE: To use the port replicator, the Vehicle Dock driver supplied with your computer must be installed. A port replicator is available as an option. This device eliminates the hassles of having you connect and disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector at the bottom of your computer. 1. Slide open the expansion bus connector cover. 2. Connect your port replicator to the expansion bus connector. For more detailed information, refer to the instructions supplied with the port replicator.

System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 8 GB on the DDR3 SO-DIMM slot. CAUTION: RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. When inserting or removing a RAM module, do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter. Doing so has been known to cause damage, fire, or electrical shock. To install the RAM module: 1. Remove the battery pack (see chapter 3) and make sure that the computer is not connected to AC power. 2. Carefully place the computer upside down. 3. Remove the four screws to open the compartment cover.

4. To install the RAM module, match the module's notched part with the socket's projected part and firmly insert the module into the socket at a 20-degree angle. Then push down until the retaining clips lock the module into position. CAUTION: If the RAM module is difficult to insert or difficult to push down, do not force it. Check once more to ensure that the module is positioned correctly. 5. Close the compartment cover and secure with four screws.

Chapter 5 Using BIOS Setup and System Recovery BIOS Setup Utility is a program for configuring the BIOS (Basic Input/ Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. System Recovery reinstalls Windows to your computer and restores it to the factory default status. This chapter tells you how to use the BIOS Setup and System Recovery.

BIOS Setup When and How to Use You need to run BIOS Setup Utility when: z You see an error message on the screen requesting you to run BIOS Setup Utility. z You want to restore the factory default BIOS settings. z You want to modify some specific settings according to the hardware. z You want to modify some specific settings to optimize the system performance. To run BIOS Setup Utility, press the F2 key when the prompt appears on the screen during the system startup. The prompt shows up on the screen for only a few seconds. You must press the F2 key quickly. The BIOS Setup Utility main screen appears as shown next. Main Advanced Security Boot Exit Model: SATA HDD: System Time: System Date: Processor Info: Installed System Memory: System BIOS Version: KBC/EC BIOS Version: LAN MAC Address: Serial Number: V200-X [INTEL SSDSA2M080G2GC] 80026MB [16:33:08] [07/05/2010] Intel(R)Core(TM)i7 CPU [email protected] 2048MB R1.01 R1.01u 00-22-20-0A-98-B4 12231241241324 F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select X Sub-Menu F10 Save and Exit 16

In general, you can use the arrow keys to move around and + / – keys to change the setup values. Keyboard information can be found at the bottom of the screen. NOTE: z The BIOS Setup Utility screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ. z The BIOS Setup Utility program may have been updated after the publication of this manual. z The settings you select in your operating system might override similar settings in BIOS Setup Utility. Main Menu The Main menu contains the system date and time settings as well as shows the basic configuration of the system. Main Advanced Security Boot Exit Model: SATA HDD: System Time: System Date: Processor Info: Installed System Memory: System BIOS Version: KBC/EC BIOS Version: LAN MAC Address: Serial Number: V200-X [INTEL SSDSA2M080G2GC] 80026MB [16:33:08] [07/05/2010] Intel(R)Core(TM)i7 CPU [email protected] 2048MB R1.01 R1.01u 00-22-20-0A-98-B4 12231241241324 F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select X Sub-Menu F10 Save and Exit System Time sets the system time. System Date sets the system date. 16

Advanced Menu The Advanced menu contains the advanced settings as shown next. Main Advanced Security Boot Exit Japanese Keyboard: SATA Mode Total Graphics Memory: USB Wake-Up From S3 High Brightness Thermal: TouchScreen: Serial port COM1: Serial port COM2: Serial port COM4: Boot-time Diagnostic Screen: Wake-On-LAN(WOL) Turbo Mode Intel Trusted Execution Intel AMT Setup Prompt: [Disabled] [AHCI] [MaxDVMT] [Disabled] [Disabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] [Enabled] [Disabled] [Enabled] Item Specific Help Support Japanese Keyboard F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select X Sub-Menu F10 Save and Exit Japanese Keyboard enables support for the Japanese keyboard. SATA Mode sets the mode to enhanced AHCI (Advanced Host Controller Interface) or IDE. Turbo memory feature works only when the SATA AHCI mode is enabled. Total Graphics Memory sets the amount of total graphics memory (pre-allocated + fixed + DVMT) for use by the internal graphics device. USB Wake-Up From S3 allow a USB device activity to wake up the system from S3 (Sleep) state. High Brightness Thermal allows dynamic control of maximum LCD brightness level according to the ambient temperature. This helps protect the LCD under over-heating situations. Disabled

Digitizer Type or TouchScreen (actual item shown depends on your model) Digitizer Type allows you to select the type of digitizer you are using. TouchScreen allows you to unconditionally disable it when set at Disabled. Serial Port COM1/COM2/COM4 allows you to unconditionally disable it when set at Disabled. Boot-time Diagnostic Screen allows you to display the diagnostic screen during system boot-up. Wake-On-LAN (WOL) allow a LAN activity to wake up the system from S3 (Sleep) state. Turbo Mode enables or disables Processor Turbo Mode. Intel Trusted Execution enables utilization of additional hardware capabilities provided by Intel® Trusted Execution Technology. Intel AMT Setup Prompt sets if the prompt for entering Intel AMT Setup appears during POST. If disabled, you cannot enter Intel AMT Setup.

Security Menu The Security menu contains the security settings, which safeguard your system against unauthorized use. Main Advanced Security Boot Exit Supervisor Password Is: User Password Is: Set Supervisor Password: Set User Password Password on boot: TPM Support Set Clear [Enter] [Enter] [Disabled] [Disabled] Item Specific Help Supervisor Password controls access to the setup utility. F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select X Sub-Menu F10 Save and Exit Supervisor/User Password Is shows whether you have set the supervisor/user password or not for the system. Set Supervisor/User Password sets the supervisor/user password. When typing the password, first make sure that Num Lock is off, and then type the password in the entry fields and press Enter. Confirm your password by typing it again and pressing Enter. You can set the supervisor/user password to be required for starting up the system and/or entering BIOS Setup. NOTE: z You can set the user password only when the supervisor password has been set. z If both the administrator and user passwords are set, you can enter any of them for starting up the system and/or entering BIOS Setup. However, the user password only allows you to view/change the settings of certain items. Enter

Password on Boot allows you to enable or disable the entering of password for booting up your system. Once the password is successfully set and this item is enabled, it is required for booting up the system. TPM Support enables or disables TPM support. TPM (Trusted Platform Module) is a component on your computer’s mainboard that is specifically designed to enhance platform security by providing a protected space for key operations and other security critical tasks. NOTE: z To use the TPM feature, the TPM driver supplied with your computer must be installed. z The next two items Current TPM State and Change TPM State would only appear if the item TPM Support is set at Enabled. Current TPM State shows the current TPM state. Change TPM State allows you to select between No Change, Clear, Deactivate & Disable, and Enable & Activate.

Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. Main Advanced Security Boot Exit Boot priority order: 1: USB FDC: 2: SATA HDD: INTEL SSDSA2M080G2GC – (S1) 3: USB KEY: 4: USB HDD: 5: LAN BOOT: IBA GE Slot 00C8 v1338 6: 7: 8: Excluded from boot order: : USB CDROM: Item Specific Help Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down. and specifies the device fixed or removable exclude or include the device to boot. enables or disables a device. <1 – 4> Loads default boot sequence. F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select X Sub-Menu F10 Save and Exit The bootable devices will be automatically detected during POST and shown here, allowing you to set the sequence that the BIOS uses to look for a device from which to load the OS. Below is a brief description of keyboard usage: Key Function ↑ , ↓ Selects (highlight) a boot device. +, – Changes the boot sequence. 1 to 4 Loads the default boot sequence. X Moves the highlighted boot device from the “Boot priority order” list to the “Excluded from boot order” list, and vice versa. Shift+1 Deactivates/activates the highlighted boot device on the “Boot priority order” list. When a device has been deactivated, an “!” (exclamation) symbol appears beside the item and system will bypass it when detecting boot device during POST.

Exit Menu The Exit menu displays ways of exiting BIOS Setup Utility. After finishing with your settings, you must save and exit so that the changes can take effect. Main Advanced Security Boot Exit Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Item Specific Help Exit System Setup and save your changes to CMOS. F1 Help ↑↓ Select Item -/+ Change Values F9 Setup Defaults Esc Exit ←→ Select Menu Enter Select X Sub-Menu F10 Save and Exit Exit Saving Changes saves the changes you have made and exits BIOS Setup Utility. Exit Discarding Changes exits BIOS Setup Utility without saving the changes you have made. Load Setup Defaults loads the factory default values for all the items. Discard Changes restores the previous values for all the items. Saves Changes saves the changes you have made.

System Recovery Use System Recovery when: z Your Windows operating system does not start at all. z You want to restore the factory default Windows settings. WARNING: Using this feature will reinstall Windows to your system. All data on the hard disk drive will be lost. To run System Recovery: 1. During system startup when the following screen appears, press Ctrl + Alt + F2 keys for four seconds. 2. The message This will help you reinstall Windows to the whole HDD to factory default. All data on HDD will be lost appears on the screen to ask if you want to access System Recovery. Type 1 to continue.

3. A warning message appears as follows: **************************************** You must accept the following terms before performing the recovery process: 1. The recovery software is solely the purpose of reinstalling or restoring software associated with the hard disk of this operating Getac machine. 2. Except the above, no other use is granted hereunder. **************************************** (1)Yes, I agree to the provisions of this agreement and wish to continue. (0)No, I do not agree to the provisions of this agreement and do not wish to continue. Type 1 to continue. 4. Type Y when the message Are you sure you want to recover now? (Y)Yes (N)No appears onscreen. The following screen appears and system will perform the recovery process and Windows operating system will be re-installed to its default setting:

5. After the recovery process has been completed successfully, the GSI (Getac Smart Installer) screen is displayed at the first boot-up of Windows operating system. 6. GSI will automatically perform system hardware detection and driver installation. After GSI has completed the whole process successfully, system will reboot.

Chapter 6 Installing Software Drivers and Utilities To take full advantage of the unique features of your computer, drivers and utilities must be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers and utilities. If not, you need to install them using the disc supplied with your computer. This chapter describes how to install the drivers and utilities.

How to Use the Driver Disc NOTE: z The drivers may have been updated after this manual was published. For driver upgrade, please contact your dealer. z This disc supports Windows XP, Windows Vista, and Windows 7. z The available items may differ according to your computer model. Some items are for select models only. z Do not remove the driver disc when installing the driver. An autorun program is provided on the driver disc to help you easily install the drivers. As you insert the disc, the autorun program automatically starts. If you need to start the program manually, run the Autorun.exe program from the driver disc. When the following screen appears, select Windows XP, Windows Vista, or Windows 7 based on the operating system installed. The User Manual item on the screen allows you to view the User Manual with Adobe Acrobat Reader. If you do not have Adobe Acrobat Reader on your computer, install the program by clicking Adobe Reader.