Panasonic RC-CD350 Operating Instructions Manual

Operating instructions CD Clock Radio PRESET TUNING -PRESET SOUND EQ -S.VIRTUALIZER SLEEP CLOCK/ALARM ALARM .CHECK-ON/OFF DOZE TUNER/BAND -AUTO PRESET ADJUST PLAY MODE 2 1 3 DISPLAY -DIMMER Dear customer Thank you for purchasing this product. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. Note “EB” on the packaging indicates the United Kingdom. Matsushita Electric Industrial Co., Ltd. Web Site: http://www.panasonic.co.jp/global/ RQT7608-B H0204ZZ0 EB GN En Supplied accessories 1 loop antenna: RSA0031 Use the numbers indicated when asking for replacement parts. www. panasonic.co.uk (for UK customers only) • Order accessory and consumable items for your product with ease and confidence by telephoning our Customer Care Centre Mon-Friday 9:00am- 5:30pm. (Excluding public holidays.) • Or go on line through our Internet Accessory ordering application. • Most major credit and debit cards accepted. • All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd. • It couldn’t be simpler! Customer Care Centre For UK customers: 08705 357357 For Republic of Ireland customers: 01 289 8333 Technical Support For UK customers: 0870 1 505610 This Technical Support Hot Line number is for Panasonic PC software related products only. For Republic of Ireland, please use the Customer Care Centre number listed above for all enquiries. For all other product related enquiries, please use the Customer Care Centre numbers listed above. Troubleshooting guide Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, consult your dealer for instructions. The clock shows “-:--”. • Set the clock. There is a lot of noise. • Keep away from mobile phones, televisions, and other tuners. • Extend and change the direction of the antenna. The alarm doesn’t sound at the set time. • Ensure the alarm’s indicator is on (“ALARM 1”, “ALARM 2”, or “ALARM 3”). The memory has been cleared. • Reset the items into the memory. • Insert a battery to preserve the memory contents. “no dISC” appears. • You haven’t inserted a CD. Play doesn’t start or display is incorrect. • Clean the CD. • Clean the lens with a blower (SZZP1038C recommended). If the lens gets marked with fingerprints, gently wipe them off with a cotton swab. • Wait an hour for condensation to dry, then try again. • Make sure the label is facing out. • Replace the CD if it is scratched, warped, or irregularly shaped. The CD or radio display disappears. • These displays disappear after a few seconds. To show them again, press [DISPLAY, –DIMMER]. For the United Kingdom and Republic of Ireland

(For United Kingdom) (“EB” area code model only) For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer. If a new plug is to be fitted please observe the wiring code as stated below. If in any doubt please consult a qualified electrician. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral, Brown: Live. As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black or Blue. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red. WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN/YELLOW. THIS PLUG IS NOT WATERPROOF–KEEP DRY. Before use Remove the connector cover. How to replace the fuse The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug. 1. Open the fuse cover with a screwdriver. CAUTION! THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. CAUTION! • DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS. • DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS. • DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS LIGHTED CANDLES, ON THE UNIT. • DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY FRIENDLY MANNER. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. The socket outlet shall be installed near the equipment and easily accessible or the mains plug or an appliance coupler shall remain readily operable. This product may receive radio interference caused by mobile telephones during use. If such interference is apparent, please increase separation between the product and the mobile telephone. THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES. CLASS 1 LASER PRODUCT (Back of product) Caution for AC Mains Lead CAUTION! IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13-AMPERE SOCKET. Fuse cover Figure A Figure B Fuse (5 ampere) Fuse (5 ampere) Figure A Figure B 2. Replace the fuse and close or attach the fuse cover.

• Avoid cuts, scratches, or poor connections in the AC mains lead, as they may result in possible fire or electric shock hazard. Also, excessive bending, pulling or splicing of the cord should be avoided. • Do not unplug the AC mains lead by pulling on the cord. To do so may cause premature failure or a shock hazard. • Do not operate this unit on AC power in a bathroom, as a potential shock hazard may result. • If the unit is not used for a long period of time, remove the batteries to prevent potential damage due to possible battery leakage. • Do not heat, disassemble, or allow contact with flame or water. • Do not peel off the covering and do not use if the covering has been peeled off. Battery mishandling can cause electrolyte leakage which can damage items the fluid contacts and may cause a fire. If electrolyte leaks from the batteries, consult your dealer. Wash thoroughly with water if electrolyte comes in contact with any part of your body. • Do not use irregularly shaped CDs. • Do not use non-specification discs. • Do not use CDs printed with label printers available on the market. • Do not use CDs with labels and stickers that are coming off or with adhesive exuding from under labels and stickers. Note on CD-R/RW This unit can play CD-R and CD-RW recorded with CD-DA. Use an audio recording disc and finalize* it when you finish recording. The unit may not be able to play some discs due to the condition of the recording. * A process that enables CD-R/CD-RW players to play audio CD-R and CD-RW. Note Specifications are subject to change without notice. Mass and dimensions are approximate. To clean this unit, wipe with a soft, dry cloth. • Never use alcohol, paint thinner or benzine to clean this unit. • Before using chemically treated cloth, read the instructions that came with the cloth carefully. Precautions Cautions Batteries CDs Specifications Frequency range FM: AM: Sampling frequency Decoding Beam source Number of channels Wow and flutter D/A converter Speakers Power requirement Memory back-up Dimensions (W x H x D) Mass 87.5 to 108.0 MHz (50 kHz step) 522 to 1629 kHz (9 kHz step) 44.1 kHz 16 bit linear Semiconductor laser (wavelength 780 nm) 2 channel, stereo Less than possible measurement data 1 bit DAC 4.5 cm, 6 Ω x 2 AC 230-240 V, 50 Hz Power consumption: 11 W 9 V (One 6F22/6LR61, 006P battery) 266 x 149 x 137 mm 1.47 kg without battery (For the United Kingdom) 1.43 kg without battery (For Australia and New Zealand) Maintenance Power consumption in standby mode: 2.3 W

1 Press to select the time setting 2 Within 10 seconds, press to set the time Press and hold to change the time faster. 3 Press to start the clock and finish The display returns to its original state after a confirmation tone is heard. Do the following to advance the clock by an hour during the summer months. 1 Press [ADJUST, CLOCK/ALARM] to select the summer time setting ( ). 2 Press [u/3] or [4/i] to select “on”. 3 Press [ADJUST, CLOCK/ALARM] to finish (a tone sounds). appears and the clock advances by an hour. Repeat the above, selecting “OFF” in step 2, to turn off and restore the time. Connections and power EXT ANT • Stand the antenna up so it clicks into place. • When disconnecting, pull firmly. Improving reception • Extend and change the direction of the antenna. 6F22/6LR61, 006P battery (not included) This battery saves the clock, alarm, and radio-preset settings if power is interrupted. It lasts about a year (one month without AC power). Connect the AC mains lead to household mains socket (The United Kingdom only) BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 2 BEFORE CONNECTION. Connect the antenna Insert a battery (not included) for memory backup (bottom of unit) 1 Press down on the catch and pull down. 2 Pull out the connector and attach the battery. Note These speakers do not have magnetic shielding. Do not place them near televisions, personal computers or other devices easily influenced by magnetism. 3 Insert the battery as shown. Setting the clock PRESET TUNING -PRESET SOUND EQ -S.VIRTUALIZER SLEEP CLOCK/ALARM ALARM .CHECK-ON/OFF DOZE TUNER/BAND -AUTO PRESET ADJUST PLAY MODE 2 1 3 DISPLAY -DIMMER Summer time ADJUST CLOCK/ALARM Summer time setting ( ) Time setting (Original display) AM PM ADJUST CLOCK/ALARM

In step 2, press and hold to start automatic tuning. Tuning stops when a station is found. Preset up to 20 FM and 12 AM stations. Use Auto Preset to preset all the stations the unit can receive, or Manual Preset to preset only those stations you want. Do the following once each for FM and AM. Press and hold The frequency returns to the lowest in the band, then it scrolls and “AUTO” flashes. The first station to be preset plays when finished. Tune to the station Press and hold Select the channel Press Select the band Press CDs Pause Press Press again to restart play Stop and off Press Note When the CD is stopped the unit also turns off automatically. You cannot use skip, search, or the play mode. The unit is in the standby condition when the AC power supply cord is connected. The primary circuit is always “live” as long as the power cord is connected to an electrical outlet. Skip/Search Press to skip, press and hold to search Backward Forward Repeat/Random Press to select the mode 1-x: Repeat one track x: Repeat all tracks RND: Play all tracks randomly No display: Play modes off PRESET TUNING -PRESET SOUND EQ -S.VIRTUALIZER SLEEP CLOCK/ALARM ALARM .CHECK-ON/OFF DOZE TUNER/BAND -AUTO PRESET ADJUST PLAY MODE 2 1 3 DISPLAY -DIMMER PRESET TUNING -PRESET SOUND EQ -S.VIRTUALIZER DISPLAY -DIMMER SLEEP CLOCK/ALARM ALARM CHECK-ON/OFF 2 3 DOZE TUNER/BAND -AUTO PRESET PLAY MODE ADJUST 1 PRESET TUNING -PRESET SOUND EQ -S.VIRTUALIZER DISPLAY -DIMMER SLEEP CLOCK/ALARM ALARM CHECK-ON/OFF 2 3 PLAY MODE ADJUST 1 PLAY MODE -PRESET Adjust the volume 0 (min.) to 50 (max.) 1 Press to open, insert a CD, and close securely 2 Press to play Elapsed play time Track number Insert label out so it clicks into place The unit turns off automatically after finishing play of the last track. PLAY MODE -PRESET Radio Manual tuning Off Press FM mode Switch to MONO if there is a lot of noise in FM Press Sound will not be stereo but noise should reduce. Press again to cancel. Preset tuning Auto Preset Manual Preset Selecting channels PRESET TUNING -PRESET SOUND EQ -S.VIRTUALIZER SLEEP CLOCK/ALARM ALARM .CHECK-ON/OFF DOZE TUNER/BAND -AUTO PRESET ADJUST PLAY MODE 2 1 3 DISPLAY -DIMMER FM FM AM TUNER/BAND -AUTO PRESET PLAY MODE -PRESET PRESET TUNING Adjust the volume 0 (min.) to 50 (max.) 2 Tune to a station 1 Select the band PLAY MODE -PRESET MONO FM AUTO TUNER/BAND -AUTO PRESET PLAY MODE -PRESET PLAY MODE -PRESET FM PRESET TUNING TUNER/BAND -AUTO PRESET