Panasonic SC-HTB70 Owner's Manual

1 Standby/on switch (Í/I) Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. 2 Adjust the volume of this system 3 Select the input source “TV” ------------# “BD/DVD” ^-------- “ ”(------} 4 Speaker angle indicator (> 8) Angle 1: 0o tilt Speaker angle indicator lights green [HTB70] Angle 2: Tilted at 30o Speaker angle indicator lights amber [HTB70] Angle 3: Tilted at 80o/90o [HTB65] Angle 2: Tilted at 90o Speaker angle indicator lights red 5 Input selector indicators ...

image are as one. ≥To change the applied effect, refer to “Sound modes”. (> right) ≥To turn off Dolby Virtual Speaker and the 3D surround effects, select “STEREO” as the sound mode. (> right) ≥To turn off the 3D surround and the Clear-mode dialog effects, refer to “Using the Dolby Virtual Speaker effect”. (> 21) By changing the sound mode, it is possible to enjoy the sound that is suitable according to the TV program or image from connected device. ∫To select the sound mode Press [SOUND]. � ...

≥Turn muting off. (> 18) ≥Check the connections to the other device. (> 15) ≥Make sure that the received audio signal is compatible with this system. (> 25) ≥Turn this system off and then on again. ≥If the connections are correct, there might be a problem with the cables. Redo the connections with different cables. ≥Check the audio output settings on the connected device. The dual audio cannot be changed from main to secondary. If the audio received from the connected device is not “Dolby Dual Mono” or the output setting is not “Bitst ...

≥Turn off all equipment before connection and read the appropriate operating instructions. Do not connect the AC power supply cord until all other connections are completed. Connection with the TV A Optical digital audio cable ≥When you use the optical digital audio cable, insert the tip correctly into the terminal. Connection with other device B Audio cable  OPTICAL OUT OPTICAL DIGITAL AUDIO IN (TV)  L R AUDIO OUT AUDIO IN BD/DVD e.g., Set top box Refer to the operating instructions of the respective devices for the optim ...

Place the main unit in the desired position and attach each cord onto the rack or table. ≥Make sure that the slack of the cord is minimal. [A]: With basic stands [B]: With 30o stands [C]: With 80o stands A Screw (supplied) ≥Tighten securely. B Screw eye ≥Attach at a position capable of supporting over 33 kg (72.8 lbs). ≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.  e.g., With basic stands  ...

used and the wall are strong enough to support the weight of at least 33 kg (72.8 lbs). The screws and other items are not supplied as the type and size will vary with each installation. ≥Refer to step 2 for details about the required screws. ≥Be sure to attach the fall prevention cord as a secondary safety measure. Supplied accessories Additionally required accessories (commercially available) ≥Screws for wall mounting............................................................ ...

Complete all the necessary connections to the main unit. (> 15 to 17) ≥Connect the AC power supply cord to the main unit, but do not connect it to the household AC outlet until the installation is completed. Attach the cord to the main unit. A Wall mount bracket (supplied) B Screws C At least 30 mm (1 3/16q) D ‰4.0 mm (5/32q) E ‰7.5 mm to ‰9.4 mm (19/64q to 3/8q) F Wall G Wall mount bracket (supplied) H Cord§ § If the cord cannot be threaded through the holes, try bending the cord in 2 locations, about ...